Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Vortex flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Flow visualization of leading-edge vortex enhancement by spanwise blowing

Flow visualization studies were conducted in a small pilot wind tunnel to determine qualitative effects of blowing a discrete jet essentially parallel to the leading edge of a 45 deg-swept trapezoidal wing featuring leading- and trailing-edge flaps. Test parameters included wing angle-of-attack, jet momentum coefficient, leading- and trailing-edge flap deflections, and nozzle chordwise displacement. Results of this study indicate that blowing from a reflection plane over the wing enhances the leading-edge vortex and delays vortex bursting to higher angles-of-attack and greater span distances. Increased blowing rates decrease vortex size, growth rate, and vertical displacement above the wing surface at a given span station and also extend the spanwise effectiveness of lateral blowing. Deflection of a leading-edge flap delays the beneficial effects of spanwise blowing to higher angles-of-attack. Nozzle chordwise locations investigated for the wing with and without leading-edge flap deflection appear equally effective in enhancing the separated leading-edge flow.

Erickson, G. E.↗
NASA NTRS1976

A numerical study of flow phenomena within a vortex sink rate sensor

A numerical investigation of a viscous incompressible fluid with constant properties within a vortex sink rate sensor is undertaken. A computer program was developed, for obtaining the numerical solution of the Navier-Stokes equations, assuming laminar flow, having general prescribed inlet conditions and axisymmetric boundary conditions. Computational results for various viscous flows and assorted boundary conditions have been obtained. In the vortex chamber, the radial momentum is conserved, whereas the axial momentum is negligible. In the sink region, the radial and tangential velocities, as well as the tangential vorticities, have significantly high values. In the sink tube, the radial momentum is negligible. The radial momentum within the vortex chamber is converted to the axial momentum in the sink tube. A change in the flow rate had an appreciable effect within the sensor and particularly near the sink tube entrance. As the flow rate was increased, both the tangential velocity and tangential vorticity increased rapidly. At the higher flow rates, vortices were produced at the corner of the entrance section of the sink tube.

Patel, D. K.↗
NASA NTRS1979

A viscous flow analysis for the tip vortex generation process

A three dimensional, forward-marching, viscous flow analysis is applied to the tip vortex generation problem. The equations include a streamwise momentum equation, a streamwise vorticity equation, a continuity equation, and a secondary flow stream function equation. The numerical method used combines a consistently split linearized scheme for parabolic equations with a scalar iterative ADI scheme for elliptic equations. The analysis is used to identify the source of the tip vortex generation process, as well as to obtain detailed flow results for a rectangular planform wing immersed in a high Reynolds number free stream at 6 degree incidence.

Shamroth, S. J.↗
NASA NTRS2009

Fundamental Study of a Jet-in-Cross-Flow Interacting with a Vortex Generator for Film Cooling Applications

Results of an experimental study are presented on the effectiveness of a vortex generator (VG) in preventing lift-off of a jet-in-cross-flow (JICF). The study is pertinent to film-cooling applications and its relevance to NASA programs is first briefly discussed. In the experiment, the jet issues into the boundary layer at an angle of 20deg to the free-stream. The effect of a triangular, ramp-shaped VG is studied while varying its geometry and location. Detailed flow-field properties are obtained for a case in which the height of the VG and the diameter of the orifice are comparable to the approach boundary layer thickness. The VG produces a streamwise vortex pair with vorticity magnitude three times larger (and of opposite sense) than that found in the JICF alone. Such a VG appears to be most effective in keeping the jet attached to the wall. The effect of parametric variation is studied mostly from surveys ten diameters downstream from the orifice. Results over a range of jet-to-freestream momentum flux ratio (1<J<11) show that the VG has a significant effect even at the highest J covered in the experiment. When the VG height is halved there is a lift-off of the jet. On the other hand, when the height is doubled, the jet core is dissipated due to larger turbulence intensity. Varying the location of the VG, over a distance of three diameters from the orifice, is found to have little impact.

Zaman, Khairul↗
NASA NTRS1977

A generalized vortex lattice method for subsonic and supersonic flow applications

If the discrete vortex lattice is considered as an approximation to the surface-distributed vorticity, then the concept of the generalized principal part of an integral yields a residual term to the vorticity-induced velocity field. The proper incorporation of this term to the velocity field generated by the discrete vortex lines renders the present vortex lattice method valid for supersonic flow. Special techniques for simulating nonzero thickness lifting surfaces and fusiform bodies with vortex lattice elements are included. Thickness effects of wing-like components are simulated by a double (biplanar) vortex lattice layer, and fusiform bodies are represented by a vortex grid arranged on a series of concentrical cylindrical surfaces. The analysis of sideslip effects by the subject method is described. Numerical considerations peculiar to the application of these techniques are also discussed. The method has been implemented in a digital computer code. A users manual is included along with a complete FORTRAN compilation, an executed case, and conversion programs for transforming input for the NASA wave drag program.

Miranda, L. R.↗
NASA NTRS2010

Experimental Study of an Inclined Jet-In-Cross-Flow Interacting with a Vortex Generator

An experiment is conducted on the effectiveness of a vortex generator (VG) in preventing lift-off of a jet-in-cross-flow (JICF), with film-cooling application in mind. The jet issues into the boundary layer at an angle of 20 to the free-stream. The effect of a triangular ramp-shaped VG is studied while varying its geometry and location. Detailed flow-field properties are documented for a specific case in which the height of the VG and the diameter of the orifice are comparable to the approach boundary layer thickness. This combination of VG and JICF produce a streamwise vortex pair with vorticity magnitude three times larger (and of opposite sense) than that found in the JICF alone. Such a VG appears to be most effective in keeping the jet attached to the wall. While most of the data are taken at a jet-to-freestream momentum flux ratio (J) of 2, limited surveys are done for varying J. The VG is found to have a significant effect even at the highest J (=11) covered in the experiment. Effect of parametric variation is studied mostly from surveys ten diameters downstream from the orifice. When the VG height is halved there is a lift-off of the jet. On the other hand, when the height is doubled, the jet core is dissipated due to larger turbulence intensities. Varying the location of the VG, over a distance of three diameters from the orifice, is found to have little impact. Rounding off the edges of the VG with increasing radius of curvature progressively diminishes the effect. However, a small radius of curvature may be quite tolerable in practice.

Zaman, K. B. M. Q.↗
NASA NTRS2010

Automatic Tip Vortex Core Profiling for Numerical Flow Simulations of Rotorcraft in Hover

An automated approach is presented that extracts visual and quantitative data from vortex cores produced by Navier-Stokes simulations of rotorcraft in hover mode. This approach extracts contiguous rotor tip vortex-core trajectories, cross-flow velocity profiles, and vortex-core diameter variation with wake age (azimuth angle). This automated approach is faster and more accurate than a conventional manual approach. Moreover, this new approach allows for an efficient way to quantitatively compare vortex-core profiles from different flow simulations, e.g., grid resolution studies, and validate computed results with experimental data

Kao, David L.↗
NASA NTRS1995

Fractional Step and Pseudocompressibility Methods for the Solution of Incompressible Navier-Stokes Equations

The fractional step and the pseudocompressibility methods for the solution of the incompressible Navier-Stokes equations are outlined. The fractional step method is based on finite-volume formulation and uses the pressure and the volume fluxes across the faces of each cell as dependent variables. The momentum equations are solved implicitly and the Poisson equation for the pressure is solved by using the multigrid method. The pseudocompressibility approach uses an implicit-higher-order-upwind differencing scheme for the convective terms together with the Gauss-Seidel line relaxation method. The dependent variables in the pseudocompressibility approach are the pressure and the cartesian velocity components in unstaggered mesh orientation. The 90-degree square duct flow, the wing-tip vortex wake flow and unsteady turbulent flows over an oscillating NACA 0015 airfoil are computed using both the fractional step and the pseudocompressibility methods. The results obtained from two different schemes are compared against experimental measurements.

Kiris, Cetin↗
NASA NTRS1982

Flow visualization study of the horseshoe vortex in a turbine stator cascade

Flow visualization techniques were used to show the behavior of the horseshoe vortex in a large scale turbine stator cascade. Oil drops on the end wall surface flowed in response to local shear stresses, indicating the limiting flow streamlines at the surface. Smoke injected into the flow and photographed showed time averaged flow behavior. Neutrally bouyant helium filled soap bubbles followed the flow and showed up on photographs as streaks, indicating the paths followed by individual fluid particles. Preliminary attempts to control the vortex were made by injecting air through control jets drilled in the end wall near the vane leading edge. Seventeen different hole locations were tested, one at a time, and the effect of the control jets on the path follwed by smoke in the boundary layer was recorded photographically.

Gaugler, R. E.↗
NASA NTRS1992

Discrete-vortex simulation of pulsating flow on a turbulent leading-edge separation bubble

Studies are made of the turbulent separation bubble in a two-dimensional semi-infinite blunt plate aligned to a uniform free stream with a pulsating component. The discrete-vortex method is applied to simulate this flow situation because this approach is effective for representing the unsteady motions of the turbulent shear layer and the effect of viscosity near the solid surface. The numerical simulation provides reasonable predictions when compared with the experimental results. A particular frequency with a minimum reattachment is related to the drag reduction. The most effective frequency is dependent on the amplified shedding frequency. The turbulent flow structure is scrutinized. This includes the time-mean and fluctuations of the velocity and the surface pressure, together with correlations between the fluctuating components. A comparison between the pulsating flow and the non-pulsating flow at the particular frequency of the minimum reattachment length of the separation bubble suggests that the large-scale vortical structure is associated with the shedding frequency and the flow instabilities.

Sung, Hyung Jin↗
NASA NTRS1997

The Effect of Vortex Generators on a Jet in a Cross-Flow

The effect of vortex generators in the form of tabs on the penetration and spreading of a jet in a cross-flow has been studied experimentally. It is found that the tab has very little effect when placed on the leeward side, i.e., on the downstream edge of the jet nozzle relative to the free-stream flow. A study of the static pressure distribution reveals significantly lower pressures on the leeward side. Thus, when placed on that side the tab does not produce a "pressure hill" of sufficient magnitude that is the primary source of streamwise vorticity in the flow field over the tab. This qualitatively explains the ineffectiveness. In comparison, there is a significant effect on the flow field when the tab is placed on the windward side, The sense of vorticity generated by the tab in the latter configuration is opposite to that of the bound vortex pair that otherwise characterizes the flow. Thus, the strength of the bound vortex pair is diminished and the jet penetration is reduced.

Zaman, K. B. M. Q.↗
NASA NTRS2006

Unsteady Flow Simulation of High-speed Turbopumps

Computation of high-speed hydrodynamics requires high-fidelity simulation to resolve flow features involving transient flow, cavitation, tip vortex and multiple scales of unsteady fluctuations. One example of this type in aerospace is related to liquid-fueled rocket turbopump. Rocket turbopumps operate under severe conditions at very high rotational speeds typically at thousands of rpm. For example, the Shuttle orbiter low-pressure-fuel-turbopump creates transient flow features associated with reverse flows, tip clearance effects, secondary flows, vortex shedding, junction flows, and cavitation effects. Flow unsteadiness originating from the orbiter Low-Pressure-Fuel-Turbopump (LPFTP) inducer is one of the major contributors to the high frequency cyclic loading that results in high cycle fatigue damage to the flow liners just upstream of the LPFTP. The reverse flow generated at the tip of the inducer blades travels upstream and interacts with the bellows cavity. Simulation procedure for this type high-speed hydrodynamic problems requires a method for quantifying multi-scale and multi-phase flow as well as an efficient high-end computing strategy. The current paper presents a high-fidelity computational procedure for unsteady hydrodynamic problems using a high-speed liquid-fueled rocket turbopump.

Kiris, Cetin C.↗
NASA NTRS1983

Small Gas Turbine Combustor Primary Zone Study

A development process is described which consists of design, fabrication, and preliminary test evaluations of three approaches to internal aerodynamic primary zone flow patterns: (1) conventional double vortex swirl stabilization; (2) reverse flow swirl stabilization; and (3) large single vortex flow system. Each concept incorporates special design features aimed at extending the performance capability of the small engine combustor. Since inherent geometry of these combustors result in small combustion zone height and high surface area to volume ratio, design features focus on internal aerodynamics, fuel placement, and advanced cooling. The combustors are evaluated on a full scale annular combustor rig. A correlation of the primary zone performance with the overall performance is accomplished using three intrusion type gas sampling probes located at the exit of the primary zone section. Empirical and numerical methods are used for designing and predicting the performance of the three combustor concepts and their subsequent modifications. The calibration of analytical procedures with actual test results permits an updating of the analytical design techniques applicable to small reverse flow annular combustors.

Sullivan, R. E.↗
NASA NTRS1978

An experimental map of the internal structure of a vortex breakdown

The flow field of an 'axisymmetric' vortex breakdown has been mapped using a laser-Doppler anemometer. The interior of the recirculation zone is dominated by energetic, non-axisymmetric, low frequency periodic fluctuations. Spectra for a number of points inside this zone, as well as time-averaged swirl and axial velocity profiles both inside and outside the recirculation zone, have been obtained. The time-averaged streamlines in the interior show an unexpected two-celled structure attributed to the action of the fluctuations. Although the present experiment deals with one particular breakdown, flow-visualization studies indicate that the case examined is typical of the 'axisymmetric' form of breakdown over a range of flow conditions.

Faler, J. H.↗
NASA NTRS1986

Predicting Vortex Shedding in Supersonic Flow

Nonlinear aerodyanmic characteristics of missile bodies computed. Program NOZVTX calculates nonlinear aerodynamic characteristics and flow fields of missile bodies at various angles-of-attack and roll in supersonic flow. Output includes geometry, centroids, and surface pressure of source panels and positions, strengths, and velocity components of shed vortexes. NOZVTX written in FORTRAN IV for batch execution.

Mendenhall, M. R.↗
NASA NTRS1990

An experimental study of the nonlinear dynamic phenomenon known as wing rock

An experimental investigation into the physical phenomena associated with limit cycle wing rock on slender delta wings has been conducted. The model used was a slender flat plate delta wing with 80-deg leading edge sweep. The investigation concentrated on three main areas: motion characteristics obtained from time history plots, static and dynamic flow visualization of vortex position, and static and dynamic flow visualization of vortex breakdown. The flow visualization studies are correlated with model motion to determine the relationship between vortex position and vortex breakdown with the dynamic rolling moments. Dynamic roll moment coefficient curves reveal rate-dependent hysteresis, which drives the motion. Vortex position correlated with time and model motion show a time lag in the normal position of the upward moving wing vortex. This time lag may be the mechanism responsible for the hysteresis. Vortex breakdown is shown to have a damping effect on the motion.

Arena, A. S., Jr.↗