Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transitional flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Steady flows in the chromosphere and transition-zone above active regions as observed by OSO-8

Two years of data from the University of Colorado ultraviolet spectrometer aboard OSO-8 were searched for steady line-of-sight flows in the chromosphere and transition-zone above active regions. The most conspicuous pattern that emerges from this data set is that many sunspots show persistent blueshifts of transition-zone lines indicating velocities of about 20 km/s with respect to the surrounding plage areas. The data show much smaller shifts in ultraviolet emission lines arising from the chromosphere: the shifts are frequently to the blue, but sometimes redshifts do occur. Plage areas often show a redshift of the transition-zone lines relative to the surrounding quiet areas, and a strong gradient of the vertical component of the velocity is evident in many plages. One area of persistent blueshift was observed in the transition-zone above an active region filament. The energy requirement of these steady flows over sunspots is discussed.

Lites, B. W.↗
NASA NTRS1987

Computational and experimental investigation of cavity flowfields

This paper presents a computational and experimental investigation of supersonic flow past a cavity in a flat plate. The source of the particular interest in this problem is the ongoing study of the aerodynamic interference effects between a separating store and its bay in the parent body. An upwind relaxation scheme, utilizing flux vector splitting and line-Gauss-Seidel iterations, is used to solve Reynolds-averaged Navier-Stokes equations. Spatial discretizations of this two-dimensional analysis are based on implicit and finite-volume methods. Turbulence is modeled and shocks are captured. The flowfield of the symmetry plane at the half-width is computationally visualized and all flow properties are computed. Experimental tests are conducted in the Langley Unitary Plan Wind Tunnel to measure wall pressures and to capture schlieren photographs. Qualitative as well as quantitative data of computations and experiments agree very well. These two vehicles of investigation are merged to show open, closed and transitional cavity flow behaviors.

Baysal, O.↗
NASA NTRS1996

Bubble and Slug Flow at Microgravity Conditions: State of Knowledge and Open Questions

Based on the experiments carried out over the past decade at microgravity conditions, an overview of our current knowledge of bubbly and slug flows is presented. The transition from bubble to slug flow, the void fraction and the pressure drop are discussed from the data collected in the literature. The transition from bubble to slug flow may be predicted by introducing a critical void fraction that depends on the fluid properties and the pipe diameter; however, the role of coalescence which controls this transition is not clearly understood. The void fraction may be accurately calculated using a drift-flux model. It is shown from local measurements that the drift of the gas with respect to the mixture is due to non-uniform radial distribution of void fraction. The pressure drop happens to be controlled by the liquid flow for bubbly flow whereas for slug flow the experimental results show that pressure drops is larger than expected. From this study, the guidelines for future research in microgravity are given.

Colin, C.↗
NASA NTRS1989

A spectral multi-domain technique applied to stability and transition of incompressible and compressible flows

Techniques for the numerical simulation of compressible and incompressible viscous flows are described and demonstrated. The focus is on a multidomain spectral method based on the flux-balance domain-interface scheme of Macaraeg and Streett (1986). The fundamental principles of the method are reviewed, and it is shown that the multidomain spectral approach facilitates the treatment of instability and the transition to turbulence. Typical numerical results for the Taylor-Couette problem and for bounded compressible high-speed mixing layers are presented in graphs and briefly characterized.

Macaraeg, Michele↗
DOE OSTI2025

Outflow Boundary Conditions for Turbine-Integrated Rotating Detonation Combustors

This study examines outflow boundary conditions (BCs) in computational fluid dynamics (CFD) simulations of a transition duct with and without guide vanes that converts supersonic flow exiting a rotating detonation combustor (RDC) to subsonic flow to drive a turbine. Since the flow exiting the transition duct has swirling shock waves with significant spatial and temporal variations in pressure, temperature, and Mach number, imposing proper BCs poses a challenge. To ensure all swirling shock waves exit the transition duct without creating non-physical reflected waves at its outlet, this study examined three outflow BCs: (1) the average pressure imposed at the duct’s outlet, (2) a nonreflecting BC (NRBC) with a specified average pressure imposed at the duct’s outlet, (3) the average pressure imposed at the outlet of an extension duct made up of a buffer layer and a sponge layer. This study is based on the three-dimensional, unsteady density-weighted-ensemble-averaged continuity, Navier–Stokes, and energy equations for a thermally perfect gas closed by the realizable k–ε model and “enhanced” wall functions. The results obtained show that imposing an average pressure at the transition duct’s outlet produces spurious waves that degrade the physical meaningfulness of the solution. When the NRBC was applied, swirling shock waves exited the duct’s outlet without creating spurious waves. However, its usage requires the gas to be thermally, as well as calorically, perfect, which this study shows could be a concern. By imposing the average pressure at the outlet of an extension duct, the gas does not need to be calorically perfect. The results obtained show the effects of the sponge layer’s length and coarsening ratio on damping nonuniformities in non-physical reflected waves to ensure the flow exiting the transition duct’s outlet can do so as if there are no boundaries present and has the desired average pressure—even though the BC is applied at the extension duct’s outlet.

gas turbines↗
NASA NTRS1999

Water Flow Performance of a Superscale Model of the Fastrac Liquid Oxygen Pump

As part of the National Aeronautics and Space Administration's ongoing effort to lower the cost of access to space, the Marshall Space Flight Center has developed a rocket engine with 60,000 pounds of thrust for use on the Reusable Launch Vehicle technology demonstrator slated for launch in 2000. This gas generator cycle engine, known as the Fastrac engine, uses liquid oxygen and RP-1 for propellants and includes single stage liquid oxygen and RP-1 pumps and a single stage supersonic turbine on a common shaft. The turbopump design effort included the first use and application of new suction capability prediction codes and three-dimensional blade generation codes in an attempt to reduce the turbomachinery design and certification costs typically associated with rocket engine development. To verify the pump's predicted cavitation performance, a water flow test of a superscale model of the Fastrac liquid oxygen pump was conducted to experimentally evaluate the liquid oxygen pump's performance at and around the design point. The water flow test article replicated the flow path of the Fastrac liquid oxygen pump in a 1.582x scale model, including scaled seal clearances for correct leakage flow at a model operating speed of 5000 revolutions per minute. Flow entered the 3-blade axial-flow inducer, transitioned to a shrouded, 6-blade radial impeller, and discharged into a vaneless radial diffuser and collection volute. The test article included approximately 50 total and static pressure measurement locations as well as flush-mounted, high frequency pressure transducers for complete mapping of the pressure environment. The primary objectives of the water flow test were to measure the steady-state and dynamic pressure environment of the liquid oxygen pump versus flow coefficient, suction specific speed, and back face leakage flow rate. Results showed excellent correlation between the predicted and experimentally measured pump head rise at low suction specific speeds. Likewise, only small circumferential variations in steady-state impeller exit and radial diffuser pressure distributions were observed from 80% to 120% of the design flow coefficient, matching the computational predictions and confirming that the integrated design approach has minimized any exit volute-induced distortions. The test article exhibited suction performance trends typically observed in inducer designs with virtually constant head rise with decreasing inlet pressure until complete pump head breakdown. Unfortunately, the net positive suction head at 3% head fall-off occurred far below that predicted at all tested flow coefficients, resulting in a negative net positive suction head margin at the design point in water. Additional testing to map the unsteady pressure environment was conducted and interesting rotating phenomena at the inducer inlet were observed. These rotating phenomena's cell numbers, direction, and speed were correlated with pump operating parameters. The impact of the unsteady phenomena and their corresponding energy losses on the unexpectedly poor pump performance is also discussed.

Skelley, Stephen↗
NASA NTRS2021

Coupling of the FUN3D Unstructured Flow Solver and the LASTRAC Stability Code to Model Transition

We develop an iterative automated method to predict transition locations in boundary-layer flows by using the FUN3D solver to perform flow simulations and the LASTRAC code for linear stability computations. The coupling of FUN3D and LASTRAC allows for a robust physics-based approach to model boundary-layer transition by analyzing the growth of different instability waves and then using that information to iteratively update the resulting transition location. There is no user involvement during the iterative computations. We apply this automated method to subsonic flow over a flat plate with a sharp leading edge. The final solution has regions of laminar and turbulent flow with a transition onset location that agrees with experiments and stability-based correlations. This iterative automated method is also applied to an NLF(1)-0416 airfoil for conditions with and without a separation bubble. Along with predicting transition locations, we compare the streamwise distributions of surface-pressure and skin-friction coefficients to a transport-equation-based model. We consider a 6:1 prolate spheroid at three angles of attack, namely, five, ten, and fifteen degrees, where mixed-mode transition occurs due to both Tollmien-Schlichting and crossflow instabilities. The skin-friction contours and transition fronts at every angle of attack from our iterative automated method show good agreement with past experimental and computational results in the literature for the 6:1 prolate spheroid.

Transition↗
NASA NTRS1994

A Lagrangian dynamic subgrid-scale model turbulence

A new formulation of the dynamic subgrid-scale model is tested in which the error associated with the Germano identity is minimized over flow pathlines rather than over directions of statistical homogeneity. This procedure allows the application of the dynamic model with averaging to flows in complex geometries that do not possess homogeneous directions. The characteristic Lagrangian time scale over which the averaging is performed is chosen such that the model is purely dissipative, guaranteeing numerical stability when coupled with the Smagorinsky model. The formulation is tested successfully in forced and decaying isotropic turbulence and in fully developed and transitional channel flow. In homogeneous flows, the results are similar to those of the volume-averaged dynamic model, while in channel flow, the predictions are superior to those of the plane-averaged dynamic model. The relationship between the averaged terms in the model and vortical structures (worms) that appear in the LES is investigated. Computational overhead is kept small (about 10 percent above the CPU requirements of the volume or plane-averaged dynamic model) by using an approximate scheme to advance the Lagrangian tracking through first-order Euler time integration and linear interpolation in space.

Meneveau, C.↗
NASA NTRS1987

Advances in flow visualization using liquid-crystal coatings

This paper discusses a new four-part mixing method for visualizing boundary layer flows, including transitions, separation, and shock locations, by the use of liquid-crystal coatings. The method controls the event temperature and color-play bandwidth best suited to specific experimental conditions, and is easily learned. The method is applicable almost throughout the altitude and speed ranges for subsonic aircraft flight envelopes, and is also applicable to supersonic flow visualization and for general use in high- and low-speed wind tunnel and water tunnel testing.

Holmes, Bruce J.↗
NASA NTRS1991

Definition of two-phase flow behaviors for spacecraft design

Two-phase flow, thermal management systems are currently being considered as an alternative to conventional, single phase systems for future space missions because of their potential to reduce overall system mass, size, and pumping power requirements. Knowledge of flow regime transitions, heat transfer characteristics, and pressure drop correlations is necessary to design and develop two-phase systems. A boiling and condensing experiment was built in which R-12 was used as the working fluid. A two-phase pump was used to circulate a freon mixture and allow separate measurements of the vapor and liquid flow streams. The experimental package was flown five times aboard the NASA KC-135 aircraft which simulates zero-g conditions by its parabolic flight trajectory. Test conditions included stratified and annual flow regimes in 1-g which became bubbly, slug, or annular flow regimes on 0-g. A portion of this work is the analysis of adiabatic flow regimes. The superficial velocities of liquid and vapor have been obtained from the measured flow rates and are presented along with the observed flow regimes.

Reinarts, Thomas R.↗
NASA NTRS1982

Tube entrance heat transfer with deposit formation

A two-peak wall temperature profile was observed while flowing a kerosene-type gas turbine fuel through a direct-resistance heated tube at an entrance Reynolds number of about 1500. The downstream peak gradually diminished as deposits formed inside the tube, and only one peak remained after seven hours. The observation is explained qualitatively on the basis of analytical and experimental results reported in the literature. It is shown that the temperature profile can be divided into five regions: development of the thermal boundary layer, appearance of the secondary flows, fully developed thermal boundary layer, transition to turbulent flow, and turbulent flow. Deposits increase the tube roughness and reduce the length required for laminar-turbulent transition.

Szetela, E. J.↗
NASA NTRS1993

Multiblock Navier-Stokes solutions about the F/A-18 wing-LEX-fuselage configuration

Three-dimensional thin-layer Navier-Stokes computations are presented for the F/A-18 configuration. The modeled configuration includes an accurate surface representation of the fuselage, leading-edge extension (LEX), and wing, both with and without leading-edge flap deflection. A multiblock structured grid strategy is employed to decompose the computational flowfield domain around the subject configuration. Steady-state solutions are obtained from an algorithm that solves the compressible Navier-Stokes equations with an upwind-biased, flux-difference splitting approach. The results presented are based on a fully turbulent flow assumption, simulating the high Reynolds number flow conditions that correspond to a recent FI A-18 flight experiment. Good agreements between the computations and the flight test results are obtained for both surface flow patterns as well as surface pressure distributions. Furthermore, a correlation between the computed LEX vortex-core and the flight test results, observed by way of smoke visualization, is also presented.

Aircraft configurations↗
NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

Boundary layer transition↗
NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

boundary layer transition↗
NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

boundary layer transition↗
DOE OSTI2021

Impacts of Pore Network-Scale Wettability Heterogeneity on Immiscible Fluid Displacement: A Micromodel Study

The mixed-wet nature of reservoir formations imposes a wide range of rock wettability from strong resident-fluid wetting to strong invading-fluid wetting. The characteristics of two-phase flow in porous media composed of mixed-wetting surfaces remain poorly understood. In this study, we investigated the displacement of resident ethylene glycol (EG) by hexane in two mixed-wet micromodels of identical 2.5-D geometry heterogeneity, with uniformly or heterogeneously distributed patches strongly wetting to hexane. These patches are mixed among pores with unaltered EG-wetting surfaces. Along with control tests in the originally EG-wet micromodel, here we show the classic fingering and transitions in flow regimes at $logCa$ (capillary number) from -7.2 to -3.9. Moreover, pore-scale distributions of wettability and their spatial correlation influence displacement efficiency. In the two mixed-wet micromodels, we found (a) an increase of steady-state hexane saturation at the end of experiments by up to 0.12 in the capillary fingering regime and a decrease of at most by 0.06 in the viscous fingering regime, compared to the EG-wet micromodel, and (b) dispersed and fragmented hexane distribution after displacement. Brine drainage during supercritical CO 2 (scCO 2 ) injections in these micromodels occurs with lower wettability contrasts, and under similar viscosity ratios and interfacial tensions resulted in higher displacement efficiency relative to displacement of EG by hexane. While mixed-wettability can enhance displacement efficiency compared to uniform wettability, the dynamics of immiscible fluids in strong mixed-wet reservoirs are expected to be less pronounced in contributing to the efficiency of geological CO 2 sequestration, oil recovery, and remediation of hydrocarbon-contaminated aquifers.

2.5-D micromodel↗
NASA NTRS1991

On the interaction between first- and second-mode waves in a supersonic boundary layer

Linear stability theory predicts two or more types of unstable disturbances in a sufficiently high-speed boundary layer. These include the first mode, which is similar to the Tollmien-Schlichting waves found in low-speed flows, and the second mode, which does not depend strongly on the viscosity. Generally, the most unstable first mode is three-dimensional while the most unstable second mode is two-dimensional. The interaction between these two spatially unstable modes are studied by direct solution of the three-dimensional Navier-Stokes equations. It is found that the two-dimensional second mode causes a significant increase in the nonlinearity and in the three-dimensionality of the flowfield. The results suggest that this interaction may accelerate transition for flows where the second mode has a significant growth rate.

Maestrello, L.↗