Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Surface segregation in titanium as monitored by Auger electron spectroscopy

Investigation of the surface diffusion and segregation of bulk impurities in titanium single crystals under well-defined and controlled experimental conditions. It is shown that an atomically clean titanium single-crystal surface can be obtained by argon ion bombardment within the temperature range from 700 to 800 C. It is demonstrated by Auger electron spectroscopy that, if such clean surfaces are subjected to thermal treatment, bulk impurities, especially sulfur, diffuse out to the crystal surface, and that the rate of surface segregation increases with increasing temperature.

Khan, I. H.↗

Aqueous chloride stress corrosion cracking of titanium - A comparison with environmental hydrogen embrittlement

The physical characteristics of stress corrosion cracking of titanium in an aqueous chloride environment are compared with those of embrittlement of titanium by a gaseous hydrogen environment in an effort to help contribute to the understanding of the possible role of hydrogen in the complex stress corrosion cracking process. Based on previous studies, the two forms of embrittlement are shown to be similar at low hydrogen pressures (100 N/sq m) but dissimilar at higher hydrogen pressures. In an effort to quantify this comparison, tests were conducted in an aqueous chloride solution using the same material and test techniques as had previously been employed in a gaseous hydrogen environment. The results of these tests strongly support models based on hydrogen as the embrittling species in an aqueous chloride environment.

Nelson, H. G.↗

Effect of surface pre-oxidation on hydrogen permeation in alpha titanium

The effect of a specific oxidation treatment, to which a titanium specimen was subjected, on the permeation of hydrogen through the titanium specimen was studied. The oxidation treatment involved the maintenance of the specimen in an oxygen atmosphere at a temperature of 270 C for a time of four hours. It was found that the oxidation treatment has the effect of decreasing the permeation rate. However, the first power pressure dependency is not affected.

Shah, K. K.↗

The effect of microstructure on the fracture toughness of titanium alloys

The microstructure of the alpha titanium alloy Ti-5Al-2.5Sn and the metastable beta titanium alloy Beta 3 was examined. The material was from normal and extra low interstitial grade plates which were either air-cooled or furnace-cooled from an annealing treatment. Beta 3 was studied in alpha-aged and omega-aged plates which were heat treated to similar strength levels. Tensile and plane strain fracture toughness tests were conducted at room temperature on the alpha-aged material. The microstructure and fracture mechanisms of alloys were studied using optical metallography, electron microscopy, microprobe analyses, and texture pole figures. Future experiments are described.

Vanstone, R. H.↗

Titanium honeycomb acoustic lining structural and thermal test report

The results are presented of static, fatigue and thermal testing of titanium honeycomb acoustic panels representing the acoustic tailpipe for the Pratt and Whitney Aircraft JT8D Refan engine which is being studied for use on the Boeing 727-200 airplane. Test specimens represented the engine and tailpipe flange joints, the rail to which the thrust reverser is attached and shear specimens of the tailpipe honeycomb. Specimens were made in four different batches with variations in configuration, materials and processes in each. Static strength of all test specimens exceeded the design ultimate load requirements. Fatigue test results confirmed that aluminum brazed titanium, as used in the Refan tailpipe design, meets the fatigue durability objectives. Quality of welding was found to be critical to life, with substandard welding failing prematurely, whereas welding within the process specification exceeded the panel skin life. Initial fatigue testing used short grip length bolts which failed prematurely. These were replaced with longer bolts and subsequent testing demonstrated the required life. Thermal tests indicate that perforated skin acoustic honeycomb has approximately twice the heat transfer of solid skin honeycomb.

Joynes, D.↗

Fretting of titanium at temperatures to 650 C in air

Fretting wear experiments were conducted on high-purity titanium at temperatures up to 650 C. Results indicate that up to about 500 C, the fretting wear increases with temperature. A further increase in the temperature up to 650 C results in decreasing fretting wear. This change in trend of fretting wear with temperature is shown to be associated with a change in oxidation rate. Additional experiments at 650 C showed a transmission from a low rate of fretting wear to a higher rate occurred after exposure to a number of fretting cycles; the number of cycles required to cause this transition was dependent on the normal load. Scanning electron microscopy studies revealed that this transition was marked by cracking and disruption of the surface oxide film. A model was proposed that coupled the oxidation rate kinetics of titanium at 650 C with the occurrence of wear at the surface of the oxide film.

Bill, R. C.↗

Effect of nature of oxygen interactions on friction of titanium, aluminum, and molybdenum

Friction studies were conducted with a gold pin contacting titanium, aluminum, and molybdenum surfaces after exposure to oxygen with various methods. Oxygen was adsorbed on the surface, it reacted with the surface, and the surface was ion bombarded with oxygen. The presence of oxygen was monitored with Auger spectroscopy. Titanium friction varied with the mode of the metal-oxygen interaction. It was highest with the adsorbed oxygen and least with ion bombardment using oxygen. Aluminum exhibited lower friction values for the reacted and the ion bombarded surfaces than for the surface having the adsorbed layer. With molybdenum the friction coefficients were generally the same despite the nature of the surface treatment with oxygen.

Buckley, D. H.↗

Selected fretting-wear-resistant coatings for titanium - 6-percent-aluminum - 4-percent-vanadium alloy

A titanium - 6-percent-aluminum - 4-percent-vanadium alloy (Ti-6Al-4V) was subjected to fretting-wear exposures against uncoated Ti-6Al-4V as a baseline and against various coatings and surface treatments applied to Ti-6Al-4V. The coatings evaluated included plasma-sprayed tungsten carbide with 12 percent cobalt, aluminum oxide with 13 percent titanium oxide, chromium oxide, and aluminum bronze with 10 percent aromatic polyester; polymer-bonded polyimide, polyimide with graphite fluoride, polyimide with molybdenum disulfide (MoS2), and methyl phenyl silicone bonded MoS2, preoxidation surface treatment, a nitride surface treatment, and a sputtered MoS2 coating. Results of wear measurements on both the coated and uncoated surfaces after 300,000 fretting cycles indicated that the polyimide coating was the most wear resistant and caused the least wear to the uncoated mating surface.

Bill, R. C.↗

Sustained load crack growth design data for Ti-6Al-4V titanium alloy tanks containing hydrazine

Results are presented for an experimental study intended to provide sustained load crack growth (SLCG) data for Ti-6Al-4V titanium alloy tanks containing MIL-P-26536 hydrazine and refined hydrazine. Fracture mechanics data on crack growth threshold for heat-treated forgings, aged and unaged welds, and aged and unaged heat-affected zones (HAZ) are presented. All tests were made on uniaxially loaded fracture mechanics specimens involving part-through cracks, and an electrical discharge machined notch was used to start the crack. Fracture mechanics design curves of crack growth threshold stress intensity versus temperature are obtained for the temperature range 40-71 C. Major conclusions are that extreme susceptibility to SLCG in hydrazine is a universal property of unaged weld metal in Ti-6Al-4V titanium alloy of normal interstitial content, and that aging both weld metal and HAZ at 510 C for 4 hr after welding completely removes all susceptibility to SLCG induced by hydrazine, with less susceptibility to SLCG in refined hydrazine.

Lewis, J. C.↗

Gas-phase hydrogen permeation through alpha-titanium - Surface film and dimensional effects

The two techniques normally used to determine diffusivity and permeability in metals are considered and a description is presented of experiments which had been conducted to determine the direct effect of oxide and nitride films on the membrane surface as a function of location and thickness. The test specimens used in the experiments has been machined from commercially pure titanium rod. The results of the experiments show that hydrogen transport in alpha-titanium is partially or completely controlled by surface reactions depending upon membrane wall thickness and the composition and thickness of the surface film.

Shah, K. K.↗

Observations of interstellar titanium toward 47 stars

Results are presented from photoelectric scans of the interstellar 3384-A line of Ti II obtained at a resolution of 3.7 km/s for 47 stars. Although the depletion of titanium from the interstellar gas is large and highly variable, its ratio to the depletion of interstellar calcium is relatively constant; titanium is less depleted than calcium by a factor of about four. A method for determining approximate electron densities from the Ca II and Ti II column densities is applied to 51 interstellar clouds.

Stokes, G. M.↗

Problems Associated with Attaching Strain Gages to Titanium Alloy Ti-61-4V

Weldable strain gages have shown excellent high temperature characteristics for supersonic cruise aircraft application. The spotwelding attachment method, however, has resulted in serious reductions in the fatigue life of titanium alloy (Ti-6Al-4V) fatigue specimens. The reduction is so severe that the use of weldable strain gages on operational aircraft must be prohibited. The cause of the fatigue problem is thought to be a combination of the microstructure changes in the material caused by spotwelding and the presence of the flange of the stain gage. Brazing, plating, and plasma spraying were investigated as substitutes for spotwelding. The attachment of a flangeless gage by plasma spraying provided the most improvement in the fatigue life of the titanium.

Jenkins, J. M.↗

Fatigue of titanium alloys in a supersonic-cruise airplane environment

The test programs conducted by several aerospace companies and NASA, summarized in this paper, studied several titanium materials previously identified as having high potential for application to supersonic cruise airplane structures. These studies demonstrate that the temperature (560 K) by itself produced no significant degradation of the materials. However, the fatigue resistance of titanium-alloy structures, in which thermal and loading effects are combined, has been studied insufficiently. The predominant topic for future study of fatigue problems in Mach 3 structures should be the influences of thermal stress particularly, the effects of thermal stress on failure location.

Imig, L. A.↗

Effect of nitrogen-containing plasma on adherence, friction, and wear of radiofrequency-sputtered titanium carbide coatings

Friction and wear experiments on 440C steel surfaces that were rf sputtered with titanium carbide when a small percentage of nitrogen was added to the plasma were conducted. Both X-ray photoelectron spectroscopy and X-ray diffraction were used to analyze the resultant coatings. Results indicate that the small partial pressure of nitrogen (approximately 0.5 percent) markedly improves the adherence, friction, and wear properties when compared with coatings applied to sputter-etched surfaces, oxidized surfaces, or in the presence of a small oxygen partial pressure. The improvements are related to the formation of an interface containing a mixture of the nitrides of titanium and iron, which are harder than their corresponding oxides.

Brainard, W. A.↗

Use of a nitrogen-argon plasma to improve adherence of sputtered titanium carbide coatings on steel

Friction and wear experiments on 440-C steel surfaces that had been RF-sputtered with titanium carbide when a small percentage of nitrogen was added to the plasma were conducted. X-ray photoelectron spectroscopy and X-ray diffraction were used to analyze the resultant coatings. Results indicate that a small partial pressure of nitrogen (about 0.5%) markedly improves the adherence, friction, and wear properties when compared with coatings applied on sputter-etched oxidized surfaces or in the presence of a small oxygen partial pressure. The improvements are related to the formation of an interface containing a mixture of the nitrides of titanium and iron, which are harder than their corresponding oxides.

Brainard, W. A.↗

The distribution of titanium on the lunar surface

Titanium concentrations derived from the lunar-orbiting gamma-ray experiment on Apollo 15 and 16 by analyzing a spectral interval in which the titanium signal is relatively enhanced are presented. Landing site soil values provide the reference for a regression curve from which Ti concentrations in 137 regions of adequate counting statistics are calculated. Mare Tranquillitatis contains the highest, and Mare Crisium the lowest Ti concentration, and regional values in the western maria range from 1.1% to 4.1%. Highland Ti concentrations suggest a north-south symmetry which is not consistent with previously reported Fe and Th results. Comparisons with telescopic spectral reflectance studies of the maria do not show complete agreement and suggest that effects due to Fe may not have been fully removed from the reflectance data.

Metzger, A. E.↗

The titanium oxide phi system

The phy system of titanium oxide has been studied in emission in the near-infrared, with the Fourier transform spectrometer at a resolution of 8000,000. Approximately 3000 lines from 25 bands of this system have been identified, including all five 0-0 and 0-1 bands corresponding to the five natural titanium isotopes. Eleven vibrational levels have been observed, and all bands have been rotationally analyzed. Band intensities are agreement with known isotopic abundances and calculated Franck-Condon factors.

Galehouse, D. C.↗