Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Low speed aerodynamic characteristics of a vectored thrust V/STOL transport with two lift/cruise fans

A wind tunnel test was conducted to obtain power on low speed characteristics of a twin fan vectored thrust V/STOL transport aircraft. Longitudinal, as well as some lateral directional data, were analyzed. Hover, STOL, and conventional flight modes were investigated. Determination of STOL characteristics, hover characteristics, roll control effectiveness and aircraft attitude were evaluated. The study also included various means to improve the lifting capability of the aircraft such as by application of fuselage strakes, exhaust vanes capable of shifting the thrust vector aft, and external flap blowing for STOL performance.

Renselaer, D. J.↗

Experimental evaluation of foil-supported resilient-pad gas-lubricated thrust bearing

A new type of resilient-pad gas thrust bearing was tested to determine the feasibility of the design. The bearing consists of carbon graphite pads mounted asymmetrically on foil beams. Two bearing configurations were tested at thrust loads from 27 to 80 newtons at speeds to 9000 rpm. The outside diameter of the bearing was 8.9 centimeters.

Nemeth, Z. N.↗

Modular thrust subsystem approaches to solar electric propulsion module design

Three approaches are presented for packaging the elements of a 30 cm ion thrustor subsystem into a modular thrust subsystem. The individual modules, when integrated into a conceptual solar electric propulsion module are applicable to a multimission set of interplanetary flights with the Space Shuttle/Interim Upper Stage as the launch vehicle. The emphasis is on the structural and thermal integration of the components into the modular thrust subsystems. Thermal control for the power processing units is either by direct radiation through louvers in combination with heat pipes of an all heat pipe system. The propellant storage and feed system and thrustor gimbal system concepts are presented. The three approaches are compared on the basis of mass, cost, testing, interfaces, simplicity, reliability, and maintainability.

Cake, J. E.↗

An accurate solution of the gas lubricated, flat sector thrust bearing

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗

Effects of deflected thrust on the stability and performance characteristics of a close-coupled canard fighter configuration

The effect of deflected thrust on the stability and performance of a close-coupled canard fighter configuration are presented. These results were obtained at low speeds in the Langley V/STOL tunnel. Transonic as well as low-speed results are also presented for an unpowered close-coupled canard and a supercruiser configuration. The V/STOL tunnel data indicate an increase in maximum lift and reductions in drag due to lift with the addition of two-dimensional vectored thrust at the wing inboard trailing edge. The longitudinal pitchup associated with the unpowered configuration at higher angles of attack was significantly reduced with power.

Thomas, J. L.↗

Dynamics of gas-thrust bearings

Computer program calculates load coefficients, up to third harmonic, for hydrostatic gas thrust bearings. Program is useful in identification of industrial situations where gas-thrust bearings have potential applications.

Stiffler, A. K.↗

Effects of deflected thrust on the longitudinal aerodynamic characteristics of a close-coupled wing-canard configuration

The effects of power on the longitudinal aerodynamic characteristics of a close-coupled wing-canard fighter configuration with partial-span rectangular nozzles at the trailing edge of the wing were investigated. Data were obtained on a basic wing-strake configuration for nozzle and flap deflections from 0 deg to 30 deg and for nominal thrust coefficients from 0 to 0.30. The model was tested over an angle-of-attack range from -2 deg to 40 deg at Mach numbers of 0.15 and 0.18. Results show substantial improvements in lift-curve slope, in maximum lift, and in drag-due-to-lift efficiency when the canard and strakes have been added to the basic wing-fuselage (wing-alone) configuration. Addition of power increased both lift-curve slope and maximum lift, improved longitudinal stability, and reduced drag due to lift on both the wing-canard and wing-canard-strake configurations. These beneficial effects are primarily derived from boundary-layer control due to moderate thrust coefficients which delay flow separation on the nozzle and inboard portion of the wing flaps.

Yip, L. P.↗

Variable thrust nozzle for quiet turbofan engine and method of operating same

An improved method of operating a gas turbine engine is presented wherein engine-generated noise is maintained at a reduced level during reduced thrust operation. Fan speed was maintained at a constant level while fan nozzle area was increased. This maintained high inlet Mach numbers for reduced forward noise propagation and also permited reduced nozzle exhaust velocity for reduced shear noise. In another embodiment, airflow was increased by means of a fan blade pitch change or speed increase while the fan nozzle area was increased, yielding both a net reduction in engine thrust and noise.

Adamson, A. P.↗

Solid rocket booster thrust vector control subsystem test report (D-1)

The results of the sequence of tests performed on the space shuttle solid rocket booster thrust vector control subsystem are presented. The operational characteristics of the thrust vector control subsystem components, as determined from the tests, are discussed. Special analyses of fuel consumption, basic steady state characteristics, GN2 spin, and actuator displacement were reviewed which will aid in understanding the performance of the auxiliary power unit. The possibility of components malfunction is also discussed.

Pagan, B.↗

Extended performance solar electric propulsion thrust system design

A thrust system design has been established for an extended performance technology, 6.4 kW, 4800 sec specific impulse ion thruster. The configuration is comprised of ten thrusters configured with a power management and control subsystem in a modular thrust system design. The system design approach is an adaptation of that previously established for the baseline technology 2.7 kW, 3000 sec specific impulse ion thruster. The power management and control subsystem design includes a combination of individual electronics for each thruster and a set of electronics with redundancy that are common to all thrusters. The thermal dissipation from all electronics is removed with a common heat pipe/radiator assembly.

Cake, J. E.↗

Modeling of thruster and solar array characteristics in the JPL low-thrust trajectory analysis

Recent advances in thruster and solar array technology have resulted in the possibility of performing many high energy space missions previously considered infeasible. This capability was demonstrated by an extensive study last year of a comet Halley rendezvous mission. In order to perform this extremely high energy mission, several advanced concepts in electric propulsion technology were investigated; notably the use of very high power, lightweight solar arrays which directly powered the beam supply of the electric propulsion thrusters, and the use of solar concentrators on the arrays together with conventional thrusters and power processors. These technology advances have directly impacted the modeling of the solar arrays and thrusters in the programs used in generating low-thrust trajectories. The intent of this paper is to discuss the modeling of the solar arrays and thrusters as employed in the trajectory programs presently being used in low-thrust mission studies at JPL.

Sauer, C. G., Jr.↗

LOX cooled thrust chamber technology developments

An experimental LOX heat-transfer study and a LOX-cooled thrust-chamber demonstration program are summarized. Heat transfer to supercritical oxygen was investigated at 17 to 34.5 MPa (2460 to 5000 psia), and heat fluxes up to 90 MW/sq m (55 Btu/sq in.-sec). Experimental data obtained previously were correlated along with these recent data, and a design equation was derived which correlates 95% of the data within + or - 30%. Liquid-oxygen-cooled thrust chambers have been designed using this correlation and are currently being fabricated. A test program is planned for evaluating the LOX-cooled design concept using NASA test facilities. The purpose of these tests is to verify the LOX cooling correlation in a high-pressure liquid rocket engine and to determine the effects of a LOX coolant leak.

Spencer, R. G.↗

Wing and leading-edge thrust

Computer program predicts leading-edge thrust for wings of arbitrary planform at supersonic speeds. Methods used in program are based on linearized wing theory. Program first calculates lifting pressures, lift coefficients, drag coefficients, moment coefficients, and lift distributions by using aft-element sensing technique. Next, empirical function calculates set of adjusted pressure-coefficient locations along leading edge. This information is then used to determine limiting value of singularity parameter and value of local leading-edge thrust coefficient.

Carlson, H. W.↗

Operating characteristics of a cantilever-mounted resilient-pad gas-lubricated thrust bearing

A resilient-pad gas thrust bearing consisting of pads mounted on cantilever beams was tested to determine its operating characteristic. The bearing was run at a thrust load of 74 newtons to a speed of 17000 rpm. The pad film thickness and bearing friction torque were measured and compared with theory. The measured film thickness was less than that predicted by theory. The bearing friction torque was greater than that predicted by theory.

Nemeth, Z. N.↗

Effect of low-stiffness closeout overwrap on rocket thrust-chamber life

Three rocket thrust chambers with copper liners and a thrust level of 20.9 kN were cyclically test fired to failure. Two of the liners were made from oxygen free, high conductivity (OFHC) copper and from annealed Amzirc. The milled coolant channels were closed out with a thin copper closeout over which a fiberglass composite was wrapped to provide hoop strength only. Experimental data are presented, along with the results of a preliminary analysis that was performed before fabrication to evaluate the life extending potential of a thin copper closeout with a fiberglass overwrap.

Kasper, H. J.↗

The 30-centimeter ion thrust subsystem design manual

The principal characteristics of the 30-centimeter ion propulsion thrust subsystem technology that was developed to satisfy the propulsion needs of future planetary and early orbital missions are described. Functional requirements and descriptions, interface and performance requirements, and physical characteristics of the hardware are described at the thrust subsystem, BIMOD engine system, and component level.

Source record↗

Evaluation of a simplified gross thrust calculation technique using two prototype F100 turbofan engines in an altitude facility

The technique which relies on afterburner duct pressure measurements and empirical corrections to an ideal one dimensional flow analysis to determine thrust is presented. A comparison of the calculated and facility measured thrust values is reported. The simplified model with the engine manufacturer's gas generator model are compared. The evaluation was conducted over a range of Mach numbers from 0.80 to 2.00 and at altitudes from 4020 meters to 15,240 meters. The effects of variations in inlet total temperature from standard day conditions were explored. Engine conditions were varied from those normally scheduled for flight. The technique was found to be accurate to a twice standard deviation of 2.89 percent, with accuracy a strong function of afterburner duct pressure difference.

Kurtenbach, F. J.↗

Static test of a large scale swivel nozzle thrust deflector

Experimental results from a swivel nozzle thrust deflector test program are presented. The deflector was installed behind a 36-inch fan with a tip turbine hot gas drive. The maximum nozzle pressure ratio was 1.2. Nozzle thrust and flow coefficients are presented for a range of vectoring angles. The results are also compared to small scale cold flow test results. The comparison suggests a need for accurate simulation of nozzle entry pressure and temperature profiles on model tests.

Federspiel, J. F.↗