Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Structural, electrical, and optical properties of antimony-doped tin oxide films prepared at room temperature by radio frequency magnetron sputtering for transparent electrodes

Antimony-doped tin oxide (ATO) films were prepared on 7059 Corning glass substrate by the radio frequency (rf) magnetron sputtering method using SnO{sub 2} target mixed with Sb of 6 wt % at room temperature. The working pressure was varied from 0.67 to 2 Pa in steps of 0.67 Pa, and the rf power was varied from 100 to 175 W in steps of 25 W at room temperature. The thickness of the deposited ATO films was about 150 nm. X-ray diffraction (XRD) measurements showed the ATO films to be crystallized with a strong (101) preferred orientation as the rf power is increased. The spectra revealed that the deposited films were polycrystalline, retaining the tetragonal structure. The grain size was estimated from the XRD spectra using the Scherrer equation and found to decrease with a decrease in the working pressure and an increase in the rf power, while the surface roughness was observed to be smoothened. The ATO film that was deposited at a working pressure of 0.67 Pa with rf power of 175 W showed the lowest resistivity of 8.6x10{sup -3} {Omega} cm, and the optical transmittance was 86.5% in the visible wavelength range from 400 to 800 nm.

36 MATERIALS SCIENCE↗

Etching characteristics and mechanism of indium tin oxide films in an inductively coupled HBr/Ar plasma

The investigations of etch characteristics and mechanisms for indium tin oxide (In{sub 2}O{sub 3}){sub 0.9}:(SnO{sub 2}){sub 0.1} (ITO) thin films using HBr/Ar inductively coupled plasma were carried out. The ITO etch rate was measured in the range of 0%-100% Ar in the HBr/Ar mixture at fixed gas pressure (6 mTorr), input power (700 W), and bias power (200 W). Plasma parameters and composition were examined with a combination of plasma diagnostics by double Langmuir probe and global (zero-dimensional) plasma model. It was found that the ITO etch rate follows the behavior of Br atom flux but contradicts with that for H atoms and positive ions. This suggests that the ITO etch process is not limited by the ion-surface interaction kinetics and appears in the reaction-rate-limited etch regime with the Br atoms as the main chemically active species.

36 MATERIALS SCIENCE↗

Influence of annealing and Ag doping on structural and optical properties of indium tin oxide thin films

Indium tin oxide (ITO) and Ag (1.2{+-}0.1 at. %)-ITO films with the thickness of 130 nm were deposited on glass substrates at room temperature by dc magnetron sputtering and postannealed at the temperature range of 200-400 deg. C. By calculating the x-ray diffraction data, the lattice constants of all samples were obtained and the results show that the annealing led to the smaller lattice constants and the Ag doping resulted in the further lattice distortion. The refractive index n and extinction coefficient k of all samples were extracted from the transmittance spectra by means of the spectroscopic ellipsometry optimization method. Ag-ITO film annealed at 400 deg. C has the high transmittance of 80%-90% in the visible wavelength range. Ag doping dramatically increased the extinction coefficient k of ITO films in UV wavelength range but almost without change in it in visible band. Meanwhile, by contrast with ITO films, Ag-ITO films show much higher n values than that of ITO films. Finally, the optical band gaps of all samples were determined, and it has been found that there is almost no difference of band gaps between ITO and Ag-ITO films. The reasons of the influence of annealing and Ag doping on structural and optical properties of ITO thin films are discussed.

36 MATERIALS SCIENCE↗

Fast and smooth etching of indium tin oxides in BCl{sub 3}/Cl{sub 2} inductively coupled plasmas

The etching characteristics of evaporation-deposited indium tin oxide (ITO) films in BCl{sub 3}/Cl{sub 2} inductively coupled plasmas have been studied. High etch rates >200 nm/min were obtained at large BCl{sub 3}/Cl{sub 2} gas flow ratios and high rf chuck powers, suggesting that the etching process is limited by sputter desorption of InCl{sub x} and SnCl{sub x} compounds. The addition of a small amount of CF{sub 4}, which acts as reducing agent, increased the etch rate by 30% and resulted in very smooth etched surfaces. It has also been found that the material crystallinity has a pronounced influence on ITO etch rate. ITO films annealed at 500 deg. C exhibited the maximum etch resistance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Infinitely high selective inductively coupled plasma etching of an indium tin oxide binary mask structure for extreme ultraviolet lithography

Currently, extreme ultraviolet lithography (EUVL) is being investigated for next generation lithography. Among the core EUVL technologies, mask fabrication is of considerable importance due to the use of new reflective optics with a completely different configuration than those of conventional photolithography. This study investigated the etching properties of indium tin oxide (ITO) binary mask materials for EUVL, such as ITO (absorber layer), Ru (capping/etch-stop layer), and a Mo-Si multilayer (reflective layer), by varying the Cl{sub 2}/Ar gas flow ratio, dc self-bias voltage (V{sub dc}), and etch time in inductively coupled plasmas. The ITO absorber layer needs to be etched with no loss in the Ru layer on the Mo-Si multilayer for fabrication of the EUVL ITO binary mask structure proposed here. The ITO layer could be etched with an infinitely high etch selectivity over the Ru etch-stop layer in Cl{sub 2}/Ar plasma even with a very high overetch time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Properties of double-layered Ga-doped Al-zinc-oxide/titanium-doped indium-tin-oxide thin films prepared by dc magnetron sputtering applied for Si-based thin film solar cells

In this article, Ga-doped Al-zinc-oxide (GAZO)/titanium-doped indium-tin-oxide (ITIO) bi-layer films were deposited onto glass substrates by direct current (dc) magnetron sputtering. The bottom ITIO film, with a thickness of 200 nm, was sputtered onto the glass substrate. The ITIO film was post-annealed at 350 deg. C for 10-120 min as a seed layer. The effect of post-annealing conditions on the morphologies, electrical, and optical properties of ITIO films was investigated. A GAZO layer with a thickness of 1200 nm was continuously sputtered onto the ITIO bottom layer. The results show that the properties of the GAZO/ITIO films were strongly dependent on the post-annealed conditions. The spectral haze (T{sub diffuse}/T{sub total}) of the GAZO/ITIO bi-layer films increases upon increasing the post-annealing time. The haze and resistivity of the GAZO/ITIO bi-layer films were improved with the post-annealed process. After optimizing the deposition and annealing parameters, the GAZO/ITIO bi-layer film has an average transmittance of 83.20% at the 400-800 nm wavelengths, a maximum haze of 16%, and the lowest resistivity of 1.04 x 10{sup -3}{Omega} cm. Finally, the GAZO/ITIO bi-layer films, as a front electrode for silicon-based thin film solar cells, obtained a maximum efficiency of 7.10%. These encouraging experimental results have potential applications in GAZO/ITIO bi-layer film deposition by in-line sputtering without the wet-etching process and enable the production of highly efficient, low-cost thin film solar cells.

36 MATERIALS SCIENCE↗

Ag-Pd-Cu alloy inserted transparent indium tin oxide electrodes for organic solar cells

The authors report on the characteristics of Ag-Pd-Cu (APC) alloy-inserted indium tin oxide (ITO) films sputtered on a glass substrate at room temperature for application as transparent anodes in organic solar cells (OSCs). The effect of the APC interlayer thickness on the electrical, optical, structural, and morphological properties of the ITO/APC/ITO multilayer were investigated and compared to those of ITO/Ag/ITO multilayer electrodes. At the optimized APC thickness of 8 nm, the ITO/APC/ITO multilayer exhibited a resistivity of 8.55 × 10{sup −5} Ω cm, an optical transmittance of 82.63%, and a figure-of-merit value of 13.54 × 10{sup −3} Ω{sup −1}, comparable to those of the ITO/Ag/ITO multilayer. Unlike the ITO/Ag/ITO multilayer, agglomeration of the metal interlayer was effectively relieved with APC interlayer due to existence of Pd and Cu elements in the thin region of the APC interlayer. The OSCs fabricated on the ITO/APC/ITO multilayer showed higher power conversion efficiency than that of OSCs prepared on the ITO/Ag/ITO multilayer below 10 nm due to the flatness of the APC layer. The improved performance of the OSCs with ITO/APC/ITO multilayer electrodes indicates that the APC alloy interlayer prevents the agglomeration of the Ag-based metal interlayer and can decrease the thickness of the metal interlayer in the oxide-metal-oxide multilayer of high-performance OSCs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Growth mechanism and optical properties of Ti thin films deposited onto fluorine-doped tin oxide glass substrate

In this work, a detailed study of the influence of the thickness on the morphological and optical properties of titanium (Ti) thin films deposited onto rough fluorine-doped tin oxide glass by d.c. magnetron sputtering is carried out. The films were characterized by several methods for composition, crystallinity, morphology, and optical properties. Regardless of the deposition time, all the studied Ti films of 400, 1500, 2000, and 2500 nm in thickness were single crystalline in the α-Ti phase and also very similar to each other with respect to composition. Using the atomic force microscopy (AFM) technique, the authors analyzed the roughness evolution of the Ti films characteristics as a function of the film thickness. By applying the dynamic scaling theory to the AFM images, a steady growth roughness exponent α = 0.72 ± 0.02 and a dynamic growth roughness exponent β = 0.22 ± 0.02 were determined. The value of α and β are consistent with nonlinear growth model incorporating random deposition with surface diffusion. Finally, measuring the reflection spectra of the samples by a spectrophotometer in the spectral range of 300–1100 nm allowed us to investigate the optical properties. The authors observed the increments of the reflection of Ti films with thickness, which by employing the effective medium approximation theory showed an increase in thickness followed by an increase in the volume fraction of metal.

36 MATERIALS SCIENCE↗

Intense pulsed light annealing of copper zinc tin sulfide nanocrystal coatings

A promising method for forming the absorber layer in copper zinc tin sulfide [Cu{sub 2}ZnSnS{sub 4} (CZTS)] thin film solar cells is thermal annealing of coatings cast from dispersions of CZTS nanocrystals. Intense pulsed light (IPL) annealing utilizing xenon flash lamps is a potential high-throughput, low-cost, roll-to-roll manufacturing compatible alternative to thermal annealing in conventional furnaces. The authors studied the effects of flash energy density (3.9–11.6 J/cm{sup 2}) and number of flashes (1–400) during IPL annealing on the microstructure of CZTS nanocrystal coatings cast on molybdenum-coated soda lime glass substrates (Mo-coated SLG). The annealed coatings exhibited cracks with two distinct linear crack densities, 0.01 and 0.2 μm{sup −1}, depending on the flash intensity and total number of flashes. Low density cracking (0.01 μm{sup −1}, ∼1 crack per 100 μm) is caused by decomposition of CZTS at the Mo-coating interface. Vapor decomposition products at the interface cause blisters as they escape the coating. Residual decomposition products within the blisters were imaged using confocal Raman spectroscopy. In support of this hypothesis, replacing the Mo-coated SLG substrate with quartz eliminated blistering and low-density cracking. High density cracking is caused by rapid thermal expansion and contraction of the coating constricted on the substrate as it is heated and cooled during IPL annealing. Finite element modeling showed that CZTS coatings on low thermal diffusivity materials (i.e., SLG) underwent significant differential heating with respect to the substrate with rapid rises and falls of the coating temperature as the flash is turned on and off, possibly causing a build-up of tensile stress within the coating prompting cracking. Use of a high thermal diffusivity substrate, such as a molybdenum foil (Mo foil), reduces this differential heating and eliminates the high-density cracking. IPL annealing in presence of sulfur vapor prevented both low- and high-density cracking as well as blistering. However, grain growth was limited even after annealing with 400 flashes. This lack of grain growth is attributed to a difficulty of maintaining high sulfur vapor pressure and absence of alkali metal impurities when Mo foil substrates are used.

36 MATERIALS SCIENCE↗

Silver diffusion over silicon surfaces with adsorbed tin atoms

Silver diffusion over the (111), (100), and (110) surfaces of silicon with preliminarily adsorbed tin atoms is studied by Auger electron spectroscopy and low-energy electron diffraction. Diffusion is observed only on the surface of Si(111)-2√3 × 2√3-Sn. The diffusion mechanism is established. It is found that the diffusion coefficient depends on the concentration of diffusing atoms. The diffusion coefficient decreases with increasing silver concentration, while the activation energy and the preexponential factor increase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Systematization of the yields of products of photonuclear reactions on enriched-tin targets at the bremsstrahlung-photon endpoint energy of 4.5 GeV

Yields of photonuclear-reaction products formed in targets from separated tin isotopes under the effect of beams of bremsstrahlung photons whose endpoint energy is 4.5 GeV were investigated. The systematization performed on this basis revealed an isoscaling character of the behavior of the production yields for various regions of reaction-product masses.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Description of cross sections for photonucleon reactions on tin isotopes at photon energies in the range 2 {<=} E{sub {gamma} {<=}} 140 MeV

A modified model of preequilibrium decay is considered. This model makes it possible to calculate cross sections for multiparticle photonucleon reactions with allowance for the impact of collective isospin effects. Features of the photodisintegration of 101 {<=} A {<=} 135 tin isotopes in the energy range 2 {<=} E{sub {gamma} {<=}} 140 MeV are studied on the basis of this model.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Topological size effect in tin-dioxide cluster films produced by reactive sputtering

The optical properties of tin-dioxide nanofilms produced by reactive sputtering are studied by the internal reflection technique and modulation polarimetry. The angular and spectral characteristics of the reflection coefficients R{sub s}{sup 2} and R{sub p}{sup 2}are studied for linear-polarized radiations, for which the wave electric field is, correspondingly, orthogonal and parallel to the plane of incidence. The characteristics of the physical difference between the reflection coefficients, {rho} = R{sub s}{sup 2}-R{sub p}{sup 2}, are studied as well. From the experimental results, it follows that (i) the doping-induced finite conductivity of the film brings about the appearance of surface plasmon resonance; (ii) the shape of the spectral and angular characteristics of the parameter {rho} is indicative of the cluster structure of the film, which is in agreement with the phase topology data obtained by atomic force microscopy; and (iii) the nonspherical shape of the clusters is responsible for the splitting of resonances and for the dependence of their parameters on the angle of incidence, which defines the topological size effect.

36 MATERIALS SCIENCE↗

Electron transport and optical properties of structures with atomic tin nanowires on vicinal GaAs substrates

Electron transport and optical properties are studied for structures with atomic tin nanowires (Sn-NWs) on vicinal GaAs substrates with misorientation angles of 0.3 and 3° with respect to the exact (100) orientation. Saturation-current anisotropy is revealed in the current–voltage characteristics of the samples for current flows along (‖ orientation) and across (⊥ orientation) the Sn-NWs: the current ratios I{sub ‖}/I{sub ⊥} are ∼1.2 and ∼2.5 for homostructures and pseudomorphic high electron mobility transistor (PHEMT) structures, respectively. The effect of the pulling voltage and illumination on current oscillations is studied in real time in the case of current flows perpendicular to the Sn-NWs. Clear anisotropy of the PHEMT frequency characteristics is shown.

36 MATERIALS SCIENCE↗

TiN Nanoporous Electrode Covered by Single Cell as Bio-Electronic Sensor of Radiation Hazard

Here we demonstrate a simple label-free bio-electronic radiation (ultra-violet) hazard detector based on non-destructive electrical impedance spectroscopy technique with a single living cell as a sensing element. Radiation results in wrong cell’s functioning and, as corollary, cell’s membrane distortion. The latter results in impedance shift for the electrode covered by the cell. The additional sensitivity of impedance shift is achieved by the simultaneous usage of the TiN porous electrodes and adaptive filtering for impedance data processing. The main advantage of the proposed sensor with respect to purely physical and/or chemical sensors is high selectivity: it a priory reacts only on the dangerous for living beings radiation.

36 MATERIALS SCIENCE↗

Structure and Electrical Properties of Zirconium-Doped Tin-Oxide Films

Thin Zr-stabilized SnO{sub 2} films are fabricated by ion-beam reactive sputtering. The amorphous thin-film SnO{sub 2} samples with various Zr concentrations are synthesized in a single production process. The influence of heat treatment on the structure and electrical properties of the synthesized films is studied. The onset of crystallization in thin-film Sn–Zr–O systems is observed at 673 and 773 K, which is accompanied by the appearance of metastable phases. Being heated to 873 K, these phases are transformed into Sn + Sn{sub 2}O{sub 3}. It is found that the electrotransfer the film crystallization at temperatures close to room temperature is thermally activated with an activation energy of ~0.78 eV. Tin-oxide films doped with Zr from 0.6 to 3.9 at % manifest the property of hydrogen-gas sensitivity after crystallization.

36 MATERIALS SCIENCE↗

Influence of the Synthesis Conditions and Tin Nanoparticles on the Structure and Properties of a-C:H〈Sn〉 Composite Thin Films

The results of studies of the structure and properties of composite materials based on amorphous carbon (a-C:H) films and tin nanoparticles are reported. The composite films are synthesized by the magnetron-assisted ion-plasma sputtering of a combined target in a 92%Ar : 4%CH{sub 4} : 4%H{sub 2} gas mixture. The dependence of the local structure of the a-C:H〈Sn〉 films on the conditions of synthesis and the content of Sn nanoparticles is clarified by means of Raman spectroscopy. The dependence of the photoluminescence intensity and the optical band gap of a-C:H〈Sn〉 films on the Sn content is shown.

36 MATERIALS SCIENCE↗

Mitigation of Sulfur Poisoning of Ni/Zirconia SOFC Anodes by Antimony and Tin

Surface Ni/Sb and Ni/Sb alloys were found to efficiently minimize the negative effects of sulfur on the performance of Ni/zirconia anode-supported solid oxide fuel cells (SOFC). Prior to operating on fuel gas containing low concentrations of H2S, the nickel/zirconia anodes were briefly exposed to antimony or tin vapor, which only slightly affected the SOFC performance. During the subsequent exposures to 1 and 5 ppm H2S, increases in anodic polarization losses were minimal compared to those observed for the standard nickel/zirconia anodes. Post-test XPS analyses showed that Sb and Sn tended to segregate to the surface of Ni particles, and further confirmed a significant reduction of adsorbed sulfur on the Ni surface in Ni/Sn and Ni/Sb samples compared to the Ni. The effect may be the result of weaker sulfur adsorption on bimetallic surfaces, adsorption site competition between sulfur and Sb or Sn on Ni, or other factors. The use of dilute binary alloys of Ni-Sb or Ni-Sn in the place of Ni, or brief exposure to Sb or Sn vapor, may be effective means to counteract the effects of sulfur poisoning in SOFC anodes and Ni catalysts. Other advantages, including suppression of coking or tailoring the anode composition for the internal reforming, are also expected.

30 DIRECT ENERGY CONVERSION↗