SEARCH · Engineering Papers

Results for “Stress strain relations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Dynamic Strength and Equation of State of Epon 828 and Diethanolamine (DEA) Polymer Epoxy Under Shock Loading

Polymers are increasingly utilized in engineering applications that can experience high loading rates, necessitating increased understanding of their response under such conditions. The tamped Richtmyer-Meshkov Instability (RMI) method was used to characterize the equation of state and dynamic strength of the polymer Epon 828 cured with Diethanolamine (DEA). Plate impact experiments that drove a uniaxial shock compression wave across a sinusoidally corrugated metal-polymer interface were performed to generate shock stresses from 4-12 GPa and strain rates of approximately 1/s in the polymer. X-ray phase contrast imaging recorded the shock motion in the polymer and subsequent interface evolution. Analysis of this data yielded the polymer equation of state and, in conjunction with numerical modeling, the dynamic strength. The equation of state was validated against one-dimensional plate impact experiments from existing literature. The dynamic strength was compared to prior data for Epon 828 and related polymers at lower strain rates and found to exhibit significant strain rate and pressure-hardening effects. The strength of the Epon 828 polymer at 10 6 1/s was found to be approximately 1.5 GPa, suggesting that it is comparable to the strength of high strength metals at these dynamic conditions.

Equation of state↗

NASA NTRS1980

Stress intensity factors in two bonded elastic layers containing cracks perpendicular to and on the interface. Part 1: Analysis

The basic crack problem which is essential for the study of subcritical crack propagation and fracture of layered structural materials is considered. Because of the apparent analytical difficulties, the problem is idealized as one of plane strain or plane stress. An additional simplifying assumption is made by restricting the formulation of the problem to crack geometries and loading conditions which have a plane of symmetry perpendicular to the interface. The general problem is formulated in terms of a coupled system of four integral equations. For each relevant crack configuration of practical interest, the singular behavior of the solution near and at the ends and points of intersection of the cracks is investigated and the related characteristic equations are obtained. The edge crack terminating at and crossing the interface, the T-shaped crack consisting of a broken layer and a delamination crack, the cross-shaped crack which consists of a delamination crack intersecting a crack which is perpendicular to the interface, and a delamination crack initiating from a stress-free boundary of the bonded layers are some of the practical crack geometries considered.

Lu, M. C.↗

NASA NTRS1983

Stress intensity factors in two bonded elastic layers containing cracks perpendicular to and on the interface. I Analysis. II - Solution and results

The basic crack problem which is essential for the study of subcritical crack propagation and fracture of layered structural materials is considered. Because of the apparent analytical difficulties, the problem is idealized as one of plane strain or plane stress. An additional simplifying assumption is made by restricting the formulation of the problem to crack geometries and loading conditions which have a plane of symmetry perpendicular to the interface. The general problem is formulated in terms of a coupled systems of four integral equations. For each relevant crack configuration of practical interest, the singular behavior of the solution near and at the ends and points of intersection of the cracks is investigated and the related characteristic equations are obtained. The edge crack terminating at and crossing the interface, the T-shaped crack consisting of a broken layer and a delamination crack, the cross-shaped crack which consists of a delamination crack intersecting a crack which is perpendicular to the interface, and a delamination crack initiating from a stress-free boundary of the bonded layers are some of the practical crack geometries considered. Previously announced in STAR as N80-18428 and N80-18429

Lu, M.-C.↗

DOE OSTI2026

Chromosome-scale Genome Assembly of the Most Abundant Ectomycorrhizal Fungus Cenococcum Geophilum Reveals Massive TE Expansion and RIP Defense Mechanism

Transposable elements (TEs) play crucial roles in genome evolution and ecological adaptation in fungi, yet their dynamics in ectomycorrhizal species remain poorly understood. Cenococcum geophilum, the most widespread ectomycorrhizal fungus in boreal and temperate forests with its large, repeat-rich genome, represents an ideal system to investigate TE-mediated adaptation to the physical environment and symbiotic lifestyle. However, previous studies have been limited by fragmented genome assemblies that prevented the resolution of repeat-rich regions. We assembled a telomere-to-telomere reference genome of C. geophilum strain 1.58 using PacBio HiFi and Hi-C datasets, resulting in a 178.54 Mbp genome with seven contiguous chromosomes. We identified 14,145 genes and over 78% of the genome consists of transposable elements (TEs). Of these, 94% are affected by repeat-induced point mutations (RIP), a genome defense mechanism that acts during the sexual reproduction phase, indicating cryptic or ancient sexual reproduction in this putatively asexual fungus. Long terminal repeat retrotransposons, LINEs, and DNA transposons dominate, with three TE families (Ty3, Ty1, and Tad1) contributing over 60% of the genome size, indicating recent transposition bursts. Screening of 15 additional C. geophilum strains revealed recent and lineage-specific TE expansions, implying that several TEs escaped the RIP machinery and retained potential activity. Supporting TE activity in the context of symbiosis, we found 56 TEs differentially transcribed between ectomycorrhizal and free-living mycelium tissues. An even higher number (n = 66) of TEs were differentially expressed between stress resistance morphology (i.e. sclerotia) and free-living mycelium. This supports that TEs are differentially regulated as a response to symbiotic and stress-related conditions. Our results demonstrate that the C. geophilum genome expansion was driven by a few lineage-specific TE families in recent history, with high RIP activity attesting to sexual reproduction. We also provide insights how TEs could respond to lifestyle transitions and traits associated with desiccation resistance.

Cenococcum geophilum↗

NASA NTRS1975

Effect of shape and size of lung and chest wall on stresses in the lung

To understand better the effect of shape and size of lung and chest wall on the distribution of stresses, strains, and surface pressures, we analyzed a theoretical model using the technique of finite elements. First we investigated the effects of changing the chest wall shape during expansion, and second we studied lungs of a variety of inherent shapes and sizes. We found that, in general, the distributions of alveolar size, mechanical stresses, and surface pressures in the lungs were dominated by the weight of the lung and that changing the shape of the lung or chest wall had relatively little effect. Only at high states of expansion where the lung was very stiff did changing the shape of the chest wall cause substantial changes. Altering the inherent shape of the lung generally had little effect but the topographical differences in stresses and surface pressures were approximately proportional to lung height. The results are generally consistent with those found in the dog by Hoppin et al (1969).

Vawter, D. L.↗

NASA NTRS1980

Thermal stress fracture in elastic-brittle materials

The reported investigation shows that the assessment of the possibility of the thermal fracture of brittle materials depends upon an accurate evaluation of the thermal stresses and the determination of the resulting stress intensity factors. The stress intensity factors can be calculated in a variety of ways ranging from the very precise to approximate, but only for a limited number of geometries. The main difficulty is related to the determination of the thermal stress field because of its unusual character and its dependence upon boundary conditions at points far from the region of thermal activity. Examination of a number of examples suggests that the best visualization of the thermal stresses and any associated fracture can be made by considering the problem to be the combination of thermal and isothermal problems or by considering that the prime effect of the temperature is in the generation of thermal strains and that the thermal stresses are simply the result of the region trying to accommodate these strains.

Emery, A. F.↗

NASA NTRS1985

Measurement and analysis of critical crack tip processes during fatigue crack growth

The mechanics of fatigue crack growth under constant-amplitudes and variable-amplitude loading were examined. Critical loading histories involving relatively simple overload and overload/underload cycles were studied to provide a basic understanding of the underlying physical processes controlling crack growth. The material used for this study was 7091-T7E69, a powder metallurgy aluminum alloy. Local crack-tip parameters were measured at various times before, during, and after the overloads, these include crack-tip opening loads and displacements, and crack-tip strain fields. The latter were useed, in combination with the materials cyclic and monotonic stress-strain properties, to compute crack-tip residual stresses. The experimental results are also compared with analytical predictions obtained using the FAST-2 computer code. The sensitivity of the analytical model to constant-amplitude fatigue crack growth rate properties and to through-thickness constrain are studied.

Davidson, D. L.↗

NASA NTRS1987

Thermo-elasto-viscoplastic analysis of problems in extension and shear

The problems of extension and shear behavior of structural elements made of carbon steel and subjected to large thermomechanical loads are investigated. The analysis is based on nonlinear geometric and constitutive relations, and is expressed in a rate form. The material constitutive equations are capable of reproducing all nonisothermal, elasto-viscoplastic characteristics. The results of the test problems show that: (1) the formulation can accommodate very large strains and rotations; (2) the model incorporates the simplification associated with rate-insensitive elastic response without losing the ability to model a rate-temperature dependent yield strength and plasticity; and (3) the formulation does not display oscillatory behavior in the stresses for the simple shear problem.

Riff, R.↗

NASA NTRS1988

Thermo-elasto-viscoplastic analysis of problems in extension and shear

Riff, R.↗

NASA NTRS1997

Creep Life Prediction of Ceramic Components Using the Finite Element Based Integrated Design Program (CARES/Creep)

The desirable properties of ceramics at high temperatures have generated interest in their use for structural applications such as in advanced turbine systems. Design lives for such systems can exceed 10,000 hours. Such long life requirements necessitate subjecting the components to relatively low stresses. The combination of high temperatures and low stresses typically places failure for monolithic ceramics in the creep regime. The objective of this work is to present a design methodology for predicting the lifetimes of structural components subjected to multiaxial creep loading. This methodology utilizes commercially available finite element packages and takes into account the time varying creep stress distributions (stress relaxation). In this methodology, the creep life of a component is divided into short time steps, during which, the stress and strain distributions are assumed constant. The damage, D, is calculated for each time step based on a modified Monkman-Grant creep rupture criterion. For components subjected to predominantly tensile loading, failure is assumed to occur when the normalized accumulated damage at any point in the component is greater than or equal to unity.

Jadaan, Osama M.↗

NASA NTRS1980

Effects of fine porosity on the fatigue behavior of a powder metallurgy superalloy

Hot isostatically pressed powder metallurgy Astroloy was obtained which contained 1.4 percent fine porosity at the grain boundaries produced by argon entering the powder container during pressing. This material was tested at 650 C in fatigue, creep fatigue, tension, and stress-rupture and the results compared with previous data on sound Astroloy. The pores averaged about 2 micrometers diameter and 20 micrometers spacing. They did influence fatigue crack initiation and produced a more intergranular mode of propagation. However, fatigue life was not drastically reduced. A large 25 micrometers pore in one specimen resulting from a hollow particle did not reduce life by 60 percent. Fatigue behavior of the porous material showed typical correlation with tensile behavior. The plastic strain range life relation was reduced proportionately with the reduction in tensile ductility, but the elastic strain range-life relation was little changed reflecting the small reduction in sigma sub u/E for the porous material.

Miner, R. V., Jr.↗

DOE OSTI2025

Modeling kinetic effects of charged vacancies on electromechanical responses of ferroelectrics: Rayleighian approach

Understanding the time-dependent effects of charged vacancies on the electromechanical responses of materials is at the forefront of research for designing materials exhibiting metal-insulator transitions and memristive behavior. A Rayleighian approach is used to develop a model for studying the nonlinear kinetics of the reaction leading to generation of vacancies and electrons via the dissociation of vacancy-electron pairs. Also, diffusion and elastic effects of charged vacancies are considered to model polarization-electric potential and strain-electric potential hysteresis loops. The model captures multiphysics phenomena by introducing couplings among polarization, the electric potential, stress, strain, and concentrations of charged (multivalent) vacancies and electrons (treated as classical negatively charged particles), where the concentrations can vary due to association-dissociation reactions. A derivation of coupled time-dependent equations based on the Rayleighian approach is presented. Three limiting cases of the governing equations are considered, highlighting the effects of (1) nonlinear reaction kinetics on the generation of charged vacancies and electrons, (2) Vegard's law (i.e., the concentration-dependent local strain) on asymmetric strain-electric potential relations, and (3) coupling between a fast component and the slow component of the net polarization on the polarization-electric-field relations. The Rayleighian approach discussed in this work should pave the way for developing a multiscale modeling framework in a thermodynamically consistent manner while capturing multiphysics phenomena in ferroelectric materials. Published by the American Physical Society 2025

Kumar, Rajeev (ORCID:0000000194943488)↗

NASA NTRS1986

A study of tectonic activity in the Basin-Range Province and on the San Andreas Fault. No. 1: Kinematics of Basin-Range intraplate extension

Strain rates assessed from brittle fracture and total brittle-ductile deformation measured from geodetic data were compared to estimates of paleo-strain from Quaternary geology for the intraplate Great Basin part of the Basin-Range, western United States. These data provide an assessment of the kinematics and mode of lithospheric extension that the western U.S. Cordillera has experienced from the past few million years to the present. Strain and deformation rates were determined by the seismic moment tensor method using historic seismicity and fault plane solutions for sub-regions of homogeneous strain. Contemporary deformation in the Great Basin occurs principally along the active seismic zones. The integrated opening rate across the entire Great Basin is accommodated by E-E extension at 8 to 10 mm/a in the north that diminishes to NW-SE extension of 3.5 mm/a in the south. Zones of maximum lithospheric extension correspond to belts of thin crust, high heat flow, and Quaternary basaltic volcanism, suggesting that these parameters are related through mechanism of extension such as a stress relaxation, allowing bouyant uplift and ascension of magmas.

Eddington, P. K.↗

NASA NTRS1957

Investigation of the Compressive Strength and Creep Lifetime of 2024-T3 Aluminum-Alloy Plates at Elevated Temperatures

The results of elevated-temperature compressive strength and creep tests of 2024-t3 (formerly 24s-t3) aluminum alloy plates supported in v-grooves are presented. The strength-test results indicate that a relation previously developed for predicting plate compressive strength for plates of all materials at room temperature is also satisfactory for determining elevated-temperature strength. Creep-lifetime results are presented for plates in the form of master creep-lifetime curves by using a time-temperature parameter that is convenient for summarizing tensile creep-rupture data. A comparison is made between tensile and compressive creep lifetime for the plates and a method that made use of isochronous stress-strain curves for predicting plate-creep failure stresses is investigated.

Mathauser, Eldon E↗

NASA NTRS2014

Assessment of Shape Memory Alloys - From Atoms To Actuators - Via In Situ Neutron Diffraction

As shape memory alloys (SMAs) become an established actuator technology, it is important to identify the fundamental mechanisms responsible for their performance by understanding microstructure performance relationships from processing to final form. Yet, microstructural examination of SMAs at stress and temperature is often a challenge since structural changes occur with stress and temperature and microstructures cannot be preserved through quenching or after stress removal, as would be the case for conventional materials. One solution to this dilemma is in situ neutron diffraction, which has been applied to the investigation of SMAs and has offered a unique approach to reveal the fundamental micromechanics and microstructural aspects of bulk SMAs in a non-destructive setting. Through this technique, it is possible to directly correlate the micromechanical responses (e.g., internal residual stresses, lattice strains), microstructural evolutions (e.g., texture, defects) and phase transformation properties (e.g., phase fractions, kinetics) to the macroscopic actuator behavior. In this work, in situ neutron diffraction was systematically employed to evaluate the deformation and transformation behavior of SMAs under typical actuator conditions. Austenite and martensite phases, yield behavior, variant selection and transformation temperatures were characterized for a polycrystalline NiTi (49.9 at. Ni). As the alloy transforms under thermomechanical loading, the measured textures and lattice plane-level variations were directly related to the cyclic actuation-strain characteristics and the dimensional instability (strain ratcheting) commonly observed in this alloy. The effect of training on the shape memory characteristics of the alloy and the development of two-way shape memory effect (TWSME) were also assessed. The final conversion from a material to a useful actuator, typically termed shape setting, was also investigated in situ during constrained heatingcooling and subsequent shape recovery experiments. Neutron diffraction techniques are also being applied to the investigation of novel high temperature SMAs with the objective of designing alloys with better stability, higher transition temperatures and ultimately superior durability.

Shape Memory Alloys↗

NASA NTRS2015

Shape Memory Alloy Rock Splitters (SMARS) - A Non-Explosive Method for Fracturing Planetary Rocklike Materials and Minerals

A static rock splitter device based on high-force, high-temperature shape memory alloys (HTSMAs) was developed for space related applications requiring controlled geologic excavation in planetary bodies such as the Moon, Mars, and near-Earth asteroids. The device, hereafter referred to as the shape memory alloy rock splitter (SMARS), consisted of active (expanding) elements made of Ni50.3Ti29.7Hf20 (at.%) that generate extremely large forces in response to thermal input. The preshaping (training) of these elements was accomplished using isothermal, isobaric and cyclic training methods, which resulted in active components capable of generating stresses in excess of 1.5 GPa. The corresponding strains (or displacements) were also evaluated and were found to be 2 to 3 percent, essential to rock fracturing and/or splitting when placed in a borehole. SMARS performance was evaluated using a test bed consisting of a temperature controller, custom heaters and heater holders, and an enclosure for rock placement and breakage. The SMARS system was evaluated using various rock types including igneous rocks (e.g., basalt, quartz, granite) and sedimentary rocks (e.g., sandstone, limestone).

NiTiHf↗

DOE OSTI2023

RB-TnSeq identifies genetic targets for improved tolerance of Pseudomonas putida towards compounds relevant to lignin conversion

We report lignin-derived mixtures intended for bioconversion commonly contain high concentrations of aromatic acids, aliphatic acids, and salts. The inherent toxicity of these chemicals places a significant bottleneck upon the effective use of microbial systems for the valorization of these mixtures. Pseudomonas putida KT2440 can tolerate stressful quantities of several lignin-related compounds, making this bacterium a promising host for converting these chemicals to valuable bioproducts. Nonetheless, further increasing P. putida tolerance to chemicals in lignin-rich substrates has the potential to improve bioprocess performance. Accordingly, we employed random barcoded transposon insertion sequencing (RB-TnSeq) to reveal genetic determinants in P. putida KT2440 that influence stress outcomes during exposure to representative constituents found in lignin-rich process streams. The fitness information obtained from the RB-TnSeq experiments informed engineering of strains via deletion or constitutive expression of several genes. Namely, ΔgacAS, ΔfleQ, ΔlapAB, ΔttgR::P tac :ttgABC, Ptac:PP_1150:PP_1152, ..delta..relA, and ΔPP_1430 mutants showed growth improvement in the presence of single compounds, and some also exhibited greater tolerance when grown using a complex chemical mixture representative of a lignin-rich chemical stream. Overall, this work demonstrates the successful implementation of a genome-scale screening tool for the identification of genes influencing stress tolerance against notable compounds within lignin-enriched chemical streams, and the genetic targets identified herein offer promising engineering targets for improving feedstock tolerance in lignin valorization strains of P. putida KT2440.

09 BIOMASS FUELS↗

DOE OSTI2024

Self-Organized Stress Distributions in Polycrystalline Materials [Dissertation]

Understanding stress distributions in solid materials is complicated by the fact that most materials are polycrystalline in nature, with each crystal having an elastically anisotropic reaction to force. This study is to gain a better understanding on how external forces placed on a polycrystal are related to internal reactions within and between the grains. The hypothesis is that the stress distribution in porous to fully dense materials are self-organized based on strong contacts between and within the individual grains created by force chains. Force chains, commonly known in loaded granular materials, and could be the phenomenon that connect micro to macro deformation. Scale bridging measurements conducted through Raman spectroscopy, Atomic Force Microscopy, and Digital Image Correlation will be used to create stress maps, modulus maps, and elastic strain maps across a variety of geological and pharmaceutical polycrystals. When possible, the resulting maps will be compared to current homogenization schemes and a full field models. Finite element modeling will be used to assess whether the patterning seen in the experimental map is a reasonable approximation based on the orientation data of the samples used. A minimum of three publications is projected to be accomplished focusing each on a different method to experimentally test and analyze stress distributions.

36 MATERIALS SCIENCE↗