Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Recycling Silicon Bottom Cells from End-of-Life Perovskite–Silicon Tandem Solar Cells

Perovskite-silicon tandem cells have shown much higher efficiencies than the single junction cells, which promises further reduction of energy cost from photovoltaics. Due to the protection by perovskites, silicon subcells in perovskite-silicon tandem cells may last much longer than they are designed for single junction devices. Here we report recycling silicon bottom cells from end-of-life perovskite-silicon tandem solar cells which further reduce their cost and enhance the sustainability. We demonstrate that silicon bottom cells can be recycled from end-oflife tandem cells by thermal delamination and chemical cleaning processes. The optoelectronic properties of silicon bottom cells were shown largely unchanged at the end-of-life tandem cells. The tandem cells refurbished from recycled silicon bottom cells show comparable efficiencies with those fabricated from fresh ones.

14 SOLAR ENERGY↗
DOE OSTI2021

Controlling Polymer Morphology in Blade-Coated All-Polymer Solar Cells

In this report translating all-polymer solar cells from spin-coating to scalable roll-to-roll-compatible fabrication techniques is a critical step toward the application of organic photovoltaics at a scale. Techniques to control polymer crystallization and phase separation during solution printing are essential to obtain high-performance printed organic solar cells. Here, we demonstrate a novel solvent additive approach employing trace amounts of phthalates as additives to control polymer crystallinity and suppress unfavorable phase separation in a representative PTB7-Th/P(NDI2OD-2T) all-polymer solar cell. The best-performing additive increased the blade-coated device performance from 2.09 to 4.50% power conversion efficiency, an over twofold improvement, mitigating the loss in performance that is typically observed during process transfer from spin-coating to blade-coating. It is suggested that the improved device performance stems from a finer polymer phase-separation size and overall improved active layer morphology, evidenced by device characterization data and indirectly supported by grazing incidence wide-angle X-ray scattering analyses. Real-time X-ray diffraction measurements during blade-coating provide mechanistic insights and suggest that the dioctyl phthalate additive may act as a compatibilizer, reducing the demixing of the donor and acceptor polymer during film formation, enabling a smaller phase separation and improved performance. The structural diversity of the class of phthalate additives makes this simple yet effective concept promising for translating other all-polymer material systems to blade-coating and other scalable printing techniques.

14 SOLAR ENERGY↗
NASA NTRS1984

GaAs CLEFT solar cells for space applications

Although GaAs solar cells are radiation-resistant and have high conversion efficiencies, there are two major obstacles that such cells must overcome before they can be widely adopted for space applications: GaAs wafers are too expensive and cells made from these wafers are too heavy. The CLEFT process permits the growth of thin single-crystal films on reusable substrates, resulting in a drastic reduction in both cell cost and cell weight. Recent advances in CLEFT technology have made it possible to achieve efficiencies of about 14 percent AM0 for 0.51-sq cm GaAs solar cells 5 microns thick with a 41-mil-thick coverglass. In preliminary experiments efficiencies close to 19 percent AM1 have been obtained for 10-micron-thick cells. It is suggested that the CLEFT technology should yield inexpensive, highly efficient modules with a beginning-of-life specific power close to 1 kW/kg (for a coverglass thickness of 4 mils).

Fan, J. C. C.↗
NASA NTRS1981

Apparatus and technique for pulsed electron beam annealing for solar cell production

Many of the demands of high-throughput processing of solar cells can be satisfied by transient methods using pulsed electron beams. A prototype pulsed electron beam processor for solar cell production has been built, and is intended for automated annealing of solar cell junction ion implantation at a rate of 1200-1800 silicon wafers per hour. Other applications include solar cell junctions by pulse diffusion, annealing of ion-implanted back surface fields, and pulse sintering of cell metallization.

Landis, G. A.↗
NASA NTRS1987

Ink jet assisted metallization for low cost flat plate solar cells

Computer-controlled ink-jet-assisted metallization of the front surface of solar cells with metalorganic silver inks offers a maskless alternative method to conventional photolithography and screen printing. This method can provide low cost, fine resolution, reduced process complexity, avoidance of degradation of the p-n junction by firing at lower temperature, and uniform line film on rough surface of solar cells. The metallization process involves belt furnace firing and thermal spiking. With multilayer ink jet printing and firing, solar cells of about 5-6 percent efficiency without antireflection (AR) coating can be produced. With a titanium thin-film underlayer as an adhesion promoter, solar cells of average efficiency 8.08 percent without AR coating can be obtained. This efficiency value is approximately equal to that of thin-film solar cells of the same lot. Problems with regard to lower inorganic content of the inks and contact resistance are noted.

Teng, K. F.↗
DOE OSTI2020

Bimolecular crystal instability and morphology of bulk heterojunction blends in organic and perovskite solar cells

The performance of polymer:fullerene bulk heterojunction (BHJ) solar cells is significantly influenced by the morphology of electron donor and acceptor blends under the premise that electronic structure is complimentary regarding donor and acceptor materials. There are many cases where intimate mixing of donor and acceptor perturbs the electronic structure, which fundamentally changes the transport and photovoltaic characteristics. In this work, we present the bimolecular crystal packing of polymers and fullerenes, and investigate the correlation between device performance and structural details. We find that bimolecular crystallization can reorganize polymer chain packing, leading to poor electron transport and device performance. The size compatibility and the passivation of entropy penalty led to cocrystallization instability, which was clearly seen by in situ GIWAXS data. PC 61 BM is found to intercalate into side chains of PQT by reorganizing both PQT and PC 61 BM, forming stable, highly ordered bimolecular crystals. The poor electron transport in bimolecular crystal domain could account for the poor device performance in both perovskite and organic solar cells. Bis-PC 61 BM, on the other hand, only forms loosely packed aggregates in solution, and then rapidly phase separated into large domains with an edge-on interfacial orientation and performed poorly in solar cells.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Performance limitations of silicon solar cells

This paper discusses the performance limitations of silicon solar cells which have been identified and investigated using a detailed numerical analysis of solar cell operation. Efficiency limitations are discussed as related to doping densities, minority carrier lifetimes, widths of solar cell regions, surface recombination, antireflecting layers, and ohmic contact stripes. Areas in which improvements can be expected in performance are identified and discussed.

Hauser, J. R.↗
NASA NTRS1976

Introduction to basic solar cell measurements

The basic approaches to solar cell performance and diagnostic measurements are described. The light sources, equipment for I-V curve measurement, and the test conditions and procedures for performance measurement are detailed. Solar cell diagnostic tools discussed include analysis of I-V curves, series resistance and reverse saturation current determination, spectral response/quantum yield measurement, and diffusion length/lifetime determination.

Brandhorst, H. W., Jr.↗
NASA NTRS1995

Photo-recovery of electron-irradiated GaAs solar cells

The first long-term (3000 hours) UV testing of unirradiated and 1 MeV electron-irradiated GaAs solar cells, with multilayer-coated coverslides to reduce solar array operating temperature, has produced some unexpected and important results. Two results, independent of the coverslide coatings, are of particular importance in terms of the predictability of GaAs solar-array lifetime in space: ( 1) The GaAs/Ge solar cells used for this series of tests displayed a much higher radiation degradation than that predicted based on JPL Solar Cell Radiation Handbook data. Covered cells degraded more in Isc than did bare cells. Short-term illumination at 60 C did not produce significant recovery (-1%) of the radiation damage. (2) However, electron radiation damage to these GaAs solar celIs anneals at 40 C when exposed to approximately 1 sun AM0 UV light sources for extended periods. The effect appears to be roughly linear with time (-1% of lsc per 1000 UVSH), is large (greater than or equal to 3%), and has not yet saturated (at 3000 hours). This photo-recovery of radiation damage to GaAs solar cells is a new effect and potentially important to the spacecraft community. The figure compares the effects of extended UV on irradiated and unirradiated GaAs solar cells with INTELSAT-6 Si cells. The effect and its generality, the extent of and conditions for photo-recovery, and the implications of such recovery for missions in radiation environments have not yet been determined.

Meulenberg, Andrew↗
NASA NTRS1995

Correcting For Capacitance In Tests Of Solar Cells

Modified procedure for testing solar photovoltaic cells and modified software for processing test data provide corrections for effects of cell capacitance. Procedure and software needed because (a) some photovoltaic devices (for example, silicon solar cells with back-surface field region) store minority charge carriers in cell junction and thus exhibit significant capacitance, (b) capacitance affects current-vs.-voltage (I-V) measurements made when transient load connected to cell, and (c) transient load used in unmodified version of test procedure. Corrected I-V curve obtained in test of solar cell according to modified procedure approximates true cell voltage vs. cell current more closely.

Mueller, Robert L.↗
DOE OSTI2026

Impact of the Annealing Temperature on the Local Se Distribution and Optical Properties in CdSexTe1-x Solar Cells by Multimodal X-ray Microscopy

The introduction of Se in CdTe solar-cell absorbers has led to multiple beneficial effects in the devices, including an increased short-circuit current and an extended charge-carrier lifetime. A critical manufacturing step of CdSexTe1-x solar cells is CdCl2 annealing at high temperatures, during which Se diffuses through the absorber layer. Understanding the local Se distribution in the absorber and its impact on optical properties of the material is key for the further development of this thin-film solar cell technology. In a multimodal x-ray scanning microscopy approach, we investigated the impact of the annealing temperature of CdSexTe1-x solar cells on the Se distribution and on optical characteristics of the material. For this purpose, we exploited an upgraded x-ray excited optical luminescence (XEOL) detection unit that enables simultaneous spectrally and temporally resolved XEOL mapping at synchrotron facilities that are ideal for studying thin-film solar-cell materials with hard x-rays featuring high penetration depth and lateral resolution.

14 SOLAR ENERGY↗
NASA NTRS1980

Planar multijunction high voltage solar cells

Technical considerations, preliminary results, and fabrication details are discussed for a family of high-voltage planar multi-junction (PMJ) solar cells which combine the attractive features of planar cells with conventional or interdigitated back contacts and the vertical multijunction (VMJ) solar cell. The PMJ solar cell is internally divided into many voltage-generating regions, called unit cells, which are internally connected in series. The key to obtaining reasonable performance from this device was the separation of top surface field regions over each active unit cell. Using existing solar cell fabricating methods, output voltages in excess of 20 volts per linear centimeter are possible. Analysis of the new device is complex, and numerous geometries are being studied which should provide substantial benefits in both normal sunlight usage as well as with concentrators.

Evans, J. C., Jr.↗
NASA NTRS1963

Low energy proton damage to solar cells.

Changes in silicon solar cells subjected to low energy proton bombardment, covering degradation of diffusion length, spectral response and efficiency under sun-like illumination

RADIATION EFFECT↗
NASA NTRS1966

Aluminum doping improves silicon solar cells

Aluminum doped silicon solar cells with resistivities in the 10- to 20-ohm centimeter range have broad spectral response, high efficiency and long lifetimes in nuclear radiation environments. Production advantages include low material rejection and increased production yields, and close tolerance control.

Source record↗