SEARCH · Engineering Papers

Results for “Shock wave experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Electrical conductivity of Sn at high pressure and temperature

To date, temperature and conductivity have many outstanding implications in extreme environments but are yet to be fully understood under high pressure and temperature dynamic conditions. Here, we introduce an approach to provide high quality electrical conductivity results under dynamic loading conditions. Emphasis is given to address the skin depth effect's influence in a dynamic loading experiment by using thin films. The thin film samples in this study were at least 100 times thinner than previous samples in dynamic electrical conductivity experiments, increasing the current density to its full potential across the sample's entire cross section. Consideration of the skin depth accounts for at minimum a 4× scaling factor to the final electrical conductivity result that has been neglected in previous dynamic electrical conductivity studies. We also obtained improved signal-to-noise ratio with custom diagnostics optimized for better electrical impedance matching. Furthermore, these considerations were applied to Sn to assess electrical conductivity at elevated pressure and temperature. The high signal-to-noise ratio with reduced skin depth influence results in Sn allowing observation of the conductivity changes related to solid-to-solid and solid-to-liquid phase transitions. Additionally, we calculate the Sn thermal conductivity using the Wiedemann-Franz law for our experiments and compare against thermal transport dependent temperature measurements from previous work.

36 MATERIALS SCIENCE↗

NASA NTRS1973

A summary of the results from the UCLA OGO-5 fluxgate magnetometer

The OGO-5 fluxgate magnetometer experiment (E-14) was designed to measure the vector magnetic field over the full range of the OGO-5 orbit. Thus, it had a dynamic range of + or - 64,000 gamma yet it maintained a precision of + or - 1/16 gamma at all times. This enabled a broad spectrum of problems to be attached. Studies of the magnetospheric waves, currents, waves-particle interactions, pitch angle distributions and wave normal directions were made. The structure of the magnetopause, the magnetotail, and bow shock were probed, waves and discontinuities in the solar wind were examined and the various phases of substorms were examined in depth.

Coleman, P. J., Jr.↗

NASA NTRS1973

Turbulence in electrostatic ion acoustic shocks

Three types of collisionless electrostatic ion acoustic shocks are investigated using a double plasma (DP) device: (1) laminar shocks; (2) small amplitude turbulent shocks in which the turbulence is confined to be upstream of the shock potential jump; and (3) large amplitude turbulent shocks in which the wave turbulence occurs throughout the shock transition. The wave turbulence is generated by ions which are reflected from the shock potential; linear theory spatial growth increments agree with experimental values. The experimental relationship between the shock Mach number and the shock potential is shown to be inconsistent with theoretical shock models which assume that the electrons are isothermal. Theoretical calculations which assume a trapped electron equation of a state and a turbulently flattened velocity distrubution function for the reflected ions yields a Mach number vs potential relationship in agreement with experiment.

Means, R. W.↗

NASA NTRS1973

Turbulence in electrostatic ion-acoustic shocks

Three types of collisionless electrostatic ion-acoustic shocks are investigated using the University of California, Los Angeles, double plasma device: (1) laminar shocks; (2) small amplitude turbulent shocks in which the turbulence is confined to be upstream of the shock potential jump; and (3) large amplitude turbulent shocks in which the wave turbulence occurs throughout the shock transition. The wave turbulence is generated by ions which are reflected from the shock potential; linear theory spatial growth increments agree with experimental values. The experimental relationship between the shock Mach number and the shock potential is shown to be inconsistent with theoretical shock models which assume that the electrons are isothermal. Theoretical calculations which assume a trapped electron equation of a state and a turbulently flattened velocity distribution function for the reflected ions yields a Mach number vs potential relationship in agreement with experiment.

Means, R. W.↗

NASA NTRS1977

Ignition of magnesium powders in shock wave induced flows

Ignition of magnesium powders, resulting from an interaction with incident shock wave-induced flows, has been studied. A numerical analysis of particle dynamics and heating is presented and compared with experimental measurements. The induction period is strongly dependent on convective heat transfer and not on chemical reaction rate. Experimentally observed ignition delays were on the order of 100 microns and were inversely dependent on shock strength and initial pressure, directly dependent on particle size and cloud concentration, and independent of oxygen concentration down to 2.3 percent oxygen. Good agreement between experiment and theory was realized.

Fox, T. W.↗

NASA NTRS1987

Observation of nonlinear wave decay processes in the solar wind by the AMPTE IRM plasma wave experiment

Nonlinear wave decay processes have been detected in the solar wind by the plasma wave experiment aboard the Active Magnetospheric Particle Tracer Explorers (AMPTE) IRM spacecraft. The main process is the generation of ultralow-frequency ion acoustic waves from the decay of Langmuir waves near the electron plasma frequency. Frequently, this is accompanied by an enhancement of emissions near twice the plasma frequency. This enhancement is most likely due to the generation of electromagnetic waves from the coalescence of two Langmuir waves. These processes occur within the electron foreshock in front of the earth's bow shock.

Koons, H. C.↗

NASA NTRS1992

Recent results on Mars and Venus; Proceedings of Symposium 3 and the Topical Meetings of the Interdisciplinary Scientific Commission C (Meeting C1) and D (Meeting D1) of the COSPAR 28th Plenary Meeting, The Hague, Netherlands, June 25-July 6, 1990

In this volume, latest results on Mars and Phobos studies are discussed along with recent results on Venus and on Martian plasma environment. Papers are presented on the characteristics of aerosol phenomena in Martian atmosphere from KRFM-experiment data, Phobos map and Phobos globe, submicron-sized dust grains in the Martian environment, remote sensing of Venus atmospheric dynamics, the latitude structure of upper clouds of Venus, and Venus thermospheric response to short-term solar variations. Attention is also given to a comparison between the bow shocks and magnetotails of Venus and Mars, comparative studies of the solar wind interaction with weakly magnetized planets, the magnetic field environment of Mars as studied by Phobos-2, waves and cold plasmas near Mars, and multiple-ion effects at Martian plasma boundaries.

Shorthill, R. W.↗

NASA NTRS1994

A flux splitting scheme with high-resolution and robustness for discontinuities

A flux splitting scheme is proposed for the general nonequilibrium flow equations with an aim at removing numerical dissipation of Van-Leer-type flux-vector splittings on a contact discontinuity. The scheme obtained is also recognized as an improved Advection Upwind Splitting Method (AUSM) where a slight numerical overshoot immediately behind the shock is eliminated. The proposed scheme has favorable properties: high-resolution for contact discontinuities; conservation of enthalpy for steady flows; numerical efficiency; applicability to chemically reacting flows. In fact, for a single contact discontinuity, even if it is moving, this scheme gives the numerical flux of the exact solution of the Riemann problem. Various numerical experiments including that of a thermo-chemical nonequilibrium flow were performed, which indicate no oscillation and robustness of the scheme for shock/expansion waves. A cure for carbuncle phenomenon is discussed as well.

Wada, Yasuhiro↗

NASA NTRS2000

Control of Shock Loading from a Jet in a Flexible Structure's Presence

The control of shock noise or screech from a jet near a flexible structure is discussed. The pressure from the supersonic jet consists of a shock with spiral and flapping nonaxisymmetric modes superimposed on broadband response. This shock induces a nonlinear-nonstationary loading problem associated with acoustic wave generation and propagation coupled with structural vibration. Control of the shock is achieved by placing a ring at the nozzle lip oscillating at the shock fundamental frequency. The ring prevents the shock characteristics originating in the column of the shear layer from sustaining connection with the out-of-phase surface vibration. Shock-free flow is maintained over a large pressure ratio. The peak power spectral density of the pressure due to shock fundamental and harmonics is converted to broadband level. The experiment is motivated by consideration of aircraft structural fatigue and interior noise.

Maestrello, Lucio↗

NASA NTRS2022

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Hydrodynamic instability↗

NASA NTRS1992

Premixed shock-induced combustion studies in the hypulse facility

Engine performance calculations strongly suggest that the oblique detonation-wave engine can outperform the diffusive-burning scramjet engine in the high hypervelocity flight regime; i.e., at flight Mach numbers exceeding about 14. Research is described that examines and characterizes the behavior of oblique detonation waves (ODW). The effort is both computational and experimental, the latter utilizing the NASA Hypulse expansion tube. The experimental work is hampered by preignition of the hydrogen-oxygen-helium mixtures in either the intermediate or acceleration sections of the facility. The experiments are described and possible causes of this preignition are discussed. Initial results obtained from a parallel computation effort indicate that temporally steady ODW are achievable in the Hypulse facility.

Chinitz, W.↗

DOE OSTI2019

Design and Scaling of an Omega-EP Experiment to Study Cold Streams Feeding Early Galaxies

Galaxies form in the centers of dark matter halos, and grow by accreting gas from the halos. The gas supply to the galaxy is the bottleneck for star formation and ultimately sets its stellar mass and star formation rate. As gas falls from the cosmic web into the halos, the highly supersonic infalling gas (Mach ~20 for Milky Way-type halos) eventually forms a shock. If cooling is inefficient, this shock quickly stabilizes as a quasi-static slowly expanding accretion shock at the outer edge of the halo. If, however, cooling is important, a recent theory suggests that filaments of gas from the cosmic web will freefall unshocked through the halos, and shock only at the outskirts of the central galaxies. Furthermore, these "cold streams" allow for a steady supply of gas into the galaxies and for more efficient star formation. The cold dense filament flowing into a hot less dense environment is potentially Kelvin–Helmholtz unstable. This instability may hinder the ability of the stream to deliver gas deeply enough into the halo. A design of a well-scaled laser experiment on Omega-EP meant for studying this phenomena is presented in the current work, with relevant theory informed by 2D hydrodynamic simulations of the experiment. We establish the hydrodynamic scaling analysis between the cosmological system and its experimental analog, presenting the experiment as an adiabatic upper limit to informing the role of mixing due to the Kelvin–Helmholtz instability.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1976

Iron line emission from a high temperature plasma in Cas A

The X-ray spectrum of Cassiopeia A was observed for several days by the proportional counter experiment on board OSO-8. The high energy ( 5 keV) data are fit well by a thermal spectrum. A narrow iron line which is predicted by the thermal model is also observed. The low energy (2-5 keV) data show an excess over the high temperature component which is consistent with the presence of an additional low temperature thermal component. Iron abundance in the source relative to normal cosmic abundance is discussed, as in the relation of this observation to shock wave and multi-component thermal models for supernova remnants.

Pravdo, S. H.↗

NASA NTRS1986

Thermal structure of the Venus ionosphere - A two-dimensional model study

A simple, two-dimensional, spectral model of heat transport in the Venus ionosphere has been constructed. Numerical experiments with the model suggest that a nocturnal heat source about an order of magnitude smaller than the daytime source is required to simulate the observed ion and electron temperatures. The solar zenith angle dependence of the high-altitude ion temperature appears to be caused by expansion followed by compression of the plasma as it flows from the dayside to the nightside. Thermal-flux saturation appears to be significant on the nightside, but the formation of a standing shock wave does not seem to be required to explain the broad features of the observed, nocturnal ion temperature.

Whitten, R. C.↗

DOE OSTI2023

Performance Characteristics of a Rotating Detonation Combustor Exiting Into a Pressurized Plenum to Simulate Gas Turbine Inlet

Abstract The present study aims to experimentally characterize the performance of a rotating detonation combustion (RDC) system integrated with a pressurized downstream plenum to simulate the high-pressure inlet conditions of power-generating gas turbines. A thorough understanding of the operational behavior including wave mode behavior, static pressure profile along the combustor length, and dynamic features of pressure fluctuations is crucial for successful integration of RDC with the turbine. In this study, two RDC configurations are investigated, RDC with a constant area annulus and RDC with a converging nozzle. In both cases, the RDC flow exited into a plenum chamber kept at pressures varying from 155 kPa to 330 kPa. RDC was operated on methane and oxygen-enriched air to represent reactants used in land-based power generation. Experiments were conducted for the two RDCs configurations operated at three reactant mass flow rates (0.23, 0.32, and 0.46 kg/s). The RDC performance is characterized by time-averaged static pressure measurements, and wave velocity determined by ionization probes. In addition, dynamic pressure measurements were recorded both inside and near the exit of RDC channel to investigate wave interactions between RDC and downstream plenum. Results show that the RDC with the converging nozzle achieved superior performance while minimizing detrimental interactions with the reflected shock and/or acoustic waves from the downstream plenum.

Engineering↗

NASA NTRS1992

Investigation of hypersonic shock-induced combustion in a hydrogen-air system

A numerical study is conducted to simulate the ballistic range experiments at Mach 5.11 and 6.46. The flow field is found to be unsteady with periodic instabilities originating in the stagnation zone. The unsteadiness of the flow field decreased with increase in the Mach number, thus indicating that it is possible to stabilize such flow fields with a high degree of overdrive. The frequency of periodic instability is determined using Fourier power spectrum and is found to be in good agreement with the experimental data. The physics of the instability is explained by the wave interaction models available in the literature.

Ahuja, J. K.↗

DOE OSTI2022

Mesoscale simulations of pressure-shear loading of granular tungsten carbide

Numerical simulations of pressure-shear loading of a granular material are performed using the shock physics code CTH. A simple mesoscale model for the granular material is used that consists of a randomly packed arrangement of solid circular or spherical grains of uniform size separated by vacuum. The grain material is described by a simple shock equation of state, elastic perfectly plastic strength model, and fracture model with baseline parameters for WC taken from previous mesoscale modeling work. Simulations using the baseline material parameters are performed at the same initial conditions of pressure-shear experiments on dry WC powders. Except for some localized flow regions appearing in simulations with an approximate treatment of sliding interfaces among grains, the samples respond elastically during shear, which is in contrast to experimental observations. By extending the simulations to higher shear wave amplitudes, macroscopic shear failure of the simulated samples is observed with the shear strength increasing with increasing stress confinement. The shear strength is also found to be strongly dependent on the grain interface treatment and on the fracture stress of the grains, though the variation in shear strength due to fracture stress decreases with increasing stress confinement. At partial compactions, the transverse velocity histories show strain-hardening behavior followed by formation of a shear interface that extends through the transverse dimensions of the sample. Near full compaction, no strain hardening is observed and, instead, the sample transitions sharply from an elastic response to formation of an internal shear interface. Agreement with experiment is shown to worsen with increasing confinement stress with simulations overpredicting the shear strengths measured in experiment. The source of the disagreement can be ultimately attributed to the Eulerian nature of the simulations, which do not treat contact and fracture realistically.

36 MATERIALS SCIENCE↗

NASA NTRS1986

An entropy correction method for unsteady full potential flows with strong shocks

An entropy correction method for the unsteady full potential equation is presented. The unsteady potential equation is modified to account for entropy jumps across shock waves. The conservative form of the modified equation is solved in generalized coordinates using an implicit, approximate factorization method. A flux-biasing differencing method, which generates the proper amounts of artificial viscosity in supersonic regions, is used to discretize the flow equations in space. Comparisons between the present method and solutions of the Euler equations and between the present method and experimental data are presented. The comparisons show that the present method more accurately models solutions of the Euler equations and experiment than does the isentropic potential formulation.

Whitlow, W., Jr.↗