Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Effects of sputtering power on properties of copper oxides thin films deposited on glass substrates

Copper oxides are deposited by radio frequency sputtering using copper target in the mixture of argon and oxygen gasses. The structural and optical properties of the copper oxides deposited at different sputtering powers have been investigated. All the films are single phase polycrystalline. At low RF power (100 W), the film is monoclinic structure of cupric oxide (CuO). Meanwhile, the films are cubic structure of cuprous oxide (Cu2O) at higher RF power. Field emission scanning electron microscopy images show the films have different morphologies with small grain size and consist of a lot of voids. The analysis of energy dispersive X-ray spectroscopy shows that the ratio of Cu to O is increased as the RF power increased. From the ultraviolet–visible spectroscopy, the films have a broad absorption edge in the range of 300–500 nm. The band gap of the films grown at RF power of 100 W, and 120 W and above, were 1.18 eV and 2.16 eV, respectively.

36 MATERIALS SCIENCE↗

Effect of direct current sputtering power on the behavior of amorphous indium-gallium-zinc-oxide thin-film transistors under negative bias illumination stress: A combination of experimental analyses and device simulation

The effect of direct current sputtering power of indium-gallium-zinc-oxide (IGZO) on the performance and stability of the corresponding thin-film transistor devices was studied. The field effect mobility increases as the IGZO sputter power increases, at the expense of device reliability under negative bias illumination stress (NBIS). Device simulation based on the extracted sub-gap density of states indicates that the field effect mobility is improved as a result of the number of acceptor-like states decreasing. The degradation by NBIS is suggested to be induced by the formation of peroxides in IGZO rather than charge trapping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Surface treatment effect on Si (111) substrate for carbon deposition using DC unbalanced magnetron sputtering

In this work, we studied the effect of HF treatment in silicon (111) substrate surface for depositing thin layer carbon. We performed the deposition of carbon by using DC Unbalanced Magnetron Sputtering with carbon pallet (5% Fe) as target. From SEM characterization results it can be concluded that the carbon layer on HF treated substrate is more uniform than on substrate without treated. Carbon deposition rate is higher as confirmed by AFM results if the silicon substrate is treated by HF solution. EDAX characterization results tell that silicon (111) substrate with HF treatment have more carbon fraction than substrate without treatment. These results confirmed that HF treatment on silicon Si (111) substrates could enhance the carbon deposition by using DC sputtering. Afterward, the carbon atomic arrangement on silicon (111) surface is studied by performing thermal annealing process to 900 °C. From Raman spectroscopy results, thin film carbon is not changing until 600 °C thermal budged. But, when temperature increase to 900 °C, thin film carbon is starting to diffuse to silicon (111) substrates.

36 MATERIALS SCIENCE↗

Stress induced growth of Sn nanowires in a single step by sputtering method

Sn nanowires in aluminum film have been synthesized in a single step by co-sputtering of Al and Sn targets. Due to immiscibility of Sn and Al, co-sputtering leads to generation of stress in the composite film. In order to attain thermodynamic equilibrium, Sn separates from Al and diffuses towards the grain boundaries. External perturbation due to ambient atmosphere leads to corrosion at the grain boundaries forming pits which provide path for Sn to evolve. Owing to this, extrusion of Sn nanowires from Al film occurs to release the residual stress in the film.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pseudo capacitive performance of copper oxide thin films grown by RF sputtering

Thin films of Copper Oxide were prepared by radio frequency magnetron sputtering on steel substrates maintained at 250°C under different RF powers ranging from 150W to 250W by keeping the sputtering pressure at 5.7×10{sup −3} mbar and O{sub 2}:Ar ratio of 1:7. The influence of RF power on the pseudo capacitive performance of thin films was studied. The X-ray diffraction studies and Raman studies indicates that all the thin films exhibits CuO phase. The electrochemical studies was done by using three electrode configuration with platinum as reference electrode. From the cyclic voltammetry studies a high rate pseudocapacitance of 227 mFcm{sup −2} at 0.5 mVs{sup −1} and 77% of capacity retention after 1000 cycles was obtained for the CuO thin films prepared at an RF power of 220W.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Resistive switching behavior of RF magnetron sputtered ZnO thin films

The resistive switching characteristics of RF magnetron sputtered zinc oxide thin films have been studied. The x-ray diffraction studies confirm the formation of crystalline ZnO on Pt/TiO{sub 2}/SiO{sub x}/Si substrate. We have fabricated Cu/ZnO/Pt device using a shadow masking technique for resistive switching study. Our Cu/ZnO/Pt device exhibits a unipolar resistive switching behaviour. The switching observed in our device could be related to oxygen vacancies or Cu ions that generate the conducting filaments responsible for resistive switching. We found HRS to LRS resistance ratio of as high as ∼200 for our Cu/ZnO/Pt device. The higher resistance ratio and stability of Cu/ZnO/Pt device would make our RF magnetron sputtered zinc oxide thin films suitable for non volatile memory applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of substrate temperature on structural and electrical properties of RF sputtered hafnium oxide thin films

In this work hafnium oxide thin films were deposited on p-type silicon substrate by Radio frequency magnetron sputtering at different substrate temperature ranging from room temperature to 300 °C. The structural and electrical properties of the sputtered films were investigated by x-ray diffraction, capacitance-voltage and current-voltage measurements. The XRD results show the formation monoclinic structure of the hafnium oxide thin films. The shifting of C-V curves towards negative voltage side depicts the increase in positive oxide charges with the rise of substrate temperature. Leakage current was found increased, when temperature enhanced from room temperature to 300 °C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Particle visualization in high-power impulse magnetron sputtering. I. 2D density mapping

Time-resolved characterization of an Ar-Ti high-power impulse magnetron sputtering discharge has been performed. This paper deals with two-dimensional density mapping in the discharge volume obtained by laser-induced fluorescence imaging. The time-resolved density evolution of Ti neutrals, singly ionized Ti atoms (Ti{sup +}), and Ar metastable atoms (Ar{sup met}) in the area above the sputtered cathode is mapped for the first time in this type of discharges. The energetic characteristics of the discharge species are additionally studied by Doppler-shift laser-induced fluorescence imaging. The questions related to the propagation of both the neutral and ionized discharge particles, as well as to their spatial density distributions, are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Growing LaAlO{sub 3}/SrTiO{sub 3} interfaces by sputter deposition

Sputter deposition of oxide materials in a high-pressure oxygen atmosphere is a well-known technique to produce thin films of perovskite oxides in particular. Also interfaces can be fabricated, which we demonstrated recently by growing LaAlO{sub 3} on SrTiO{sub 3} substrates and showing that the interface showed the same high degree of epitaxy and atomic order as is made by pulsed laser deposition. However, the high pressure sputtering of oxides is not trivial and number of parameters are needed to be optimized for epitaxial growth. Here we elaborate on the earlier work to show that only a relatively small parameter window exists with respect to oxygen pressure, growth temperature, radiofrequency power supply and target to substrate distance. In particular the sensitivity to oxygen pressure makes it more difficult to vary the oxygen stoichiometry at the interface, yielding it insulating rather than conducting.

36 MATERIALS SCIENCE↗

Selective deposition of a crystalline Si film by a chemical sputtering process in a high pressure hydrogen plasma

The selective deposition of Si films was demonstrated using a chemical sputtering process induced by a high pressure hydrogen plasma at 52.6 kPa (400 Torr). In this chemical sputtering process, the initial deposition rate (R{sub d}) is dependent upon the substrate type. At the initial stage of Si film formation, R{sub d} on glass substrates increased with elapsed time and reached to a constant value. In contrast, R{sub d} on Si substrates remained constant during the deposition. The selective deposition of Si films can be achieved by adjusting the substrate temperature (T{sub sub}) and hydrogen concentration (C{sub H2}) in the process atmosphere. For any given deposition time, it was found that an optimum C{sub H2} exists for a given T{sub sub} to realize the selective deposition of a Si film, and the optimum T{sub sub} value tends to increase with decreasing C{sub H2}. According to electron diffraction patterns obtained from the samples, the selectively prepared Si films showed epitaxial-like growth, although the Si films contained many defects. It was revealed by Raman scattering spectroscopy that some of the defects in the Si films were platelet defects induced by excess hydrogen incorporated during Si film formation. Raman spectrum also suggested that Si related radicals (SiH{sub 2}, SiH, Si) with high reactivity contribute to the Si film formation. Simple model was derived as the guideline for achieving the selective growth.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Discharge current modes of high power impulse magnetron sputtering

Based on the production and disappearance of ions and electrons in the high power impulse magnetron sputtering plasma near the target, the expression of the discharge current is derived. Depending on the slope, six possible modes are deduced for the discharge current and the feasibility of each mode is discussed. The discharge parameters and target properties are simplified into the discharge voltage, sputtering yield, and ionization energy which mainly affect the discharge plasma. The relationship between these factors and the discharge current modes is also investigated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Properties of RF sputtered cadmium telluride (CdTe) thin films: Influence of deposition pressure

Influence of deposition pressure on structural, morphology, electrical and optical properties of CdTe thin films deposited at low substrate temperature (100°C) by RF magnetron sputtering was investigated. The formation of CdTe was confirmed by low angle XRD and Raman spectroscopy. The low angle XRD analysis revealed that the CdTe films have zinc blende (cubic) structure with crystallites having preferred orientation in (111) direction. Raman spectra show the longitudinal optical (LO) phonon mode peak ∼ 165.4 cm{sup -1} suggesting high quality CdTe film were obtained over the entire range of deposition pressure studied. Scanning electron microscopy analysis showed that films are smooth, homogenous, and crack-free with no evidence of voids. The EDAX data revealed that CdTe films deposited at low deposition pressure are high-quality stoichiometric. However, for all deposition pressures, films are rich in Cd relative to Te. The UV-Visible spectroscopy analysis show the blue shift in absorption edge with increasing the deposition pressure while the band gap show decreasing trend. The highest electrical conductivity was obtained for the film deposited at deposition pressure 1 Pa which indicates that the optimized deposition pressure for our sputtering unit is 1 Pa. Based on the experimental results, these CdTe films can be useful for the application in the flexible solar cells and other opto-electronic devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spectroscopic ellipsometry-based study of optical properties of amorphous and crystalline ZnSnO alloys and Zn{sub 2}SnO{sub 4} thin films grown using sputtering deposition: Dielectric function and subgap states

We investigated the optical properties of amorphous and crystalline zinc tin oxide (ZTO) thin films grown on SiO{sub 2}/Si substrates with varying compositions via a co-sputtering deposition method at room temperature. The co-sputtering targets consist of SnO{sub 2} and ZnO. By varying the relative power ratio of the two targets, we demonstrate the ability to control the Sn and Zn composition of the resulting ZTO thin films. The ratio of [Sn]/([Sn] + [Zn]) atomic compositions was estimated at 11%, 29%, 42%, 54%, and 60%. Using a 600 °C annealing process, the as-grown amorphous ZTO films were transformed into crystalline ZTO films. The dielectric functions were obtained based on the measured ellipsometric angles, ψ and Δ. We determined the dielectric functions, absorption coefficients, and optical gap energies of ZTO thin films with varying compositions. The dielectric functions, absorption coefficients, and optical gap energies of amorphous and crystalline Zn{sub 2}SnO{sub 4} thin films were obtained at 29 at. % of Sn. Subgap states at 1.6 eV (A) and 2.8 eV (B) of ZnSnO alloys and Zn{sub 2}SnO{sub 4} films were found in the imaginary part of the dielectric function spectra. The subgap state intensities were reduced via a nitrogen gas annealing. Possible origins of the observed subgap states will be discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fabrication and characterization of pristine and annealed Ga doped ZnO thin films using sputtering

ZnO is a wide-band gap, transparent, polar semiconductor with unparalleled optoelectronic, piezoelectric, thermal and transport properties, which make it the material of choice for a wide range of applications such as blue/UV optoelectronics, energy conversion, transparent electronics, spintronic, plasmonic and sensor devices. We report, three sets of Ga doped Zinc Oxide (GZO) were fabricated in different sputtering power (100 watt, 200 watt and 300 watt). Thereafter films were annealed in nitrogen ambient for 30 minutes at 400° C. From the optical absorption spectroscopy it was found that pristine films are showing a 75% transmittance in the visible region of light and it increases after the annealing. However, for 300 W grown sample opposite trend has been achieved for the post annealed sample. X-ray diffraction pattern of all the pristine and annealed films showed a preferable growth orientation at (002) phase. Some other weak peaks were also appeared in different angle which indicates that films are polycrystalline in nature. XRD data also reveals that crystallite size increases with sputtering power up to 200 W and thereafter it decreases with the deposition power. It also noted that the crystallite size of the annealed film increases with compare to the non annealed films. At room temperature an enhancement in electrical properties of Ga doped ZnO thin films was noted for the annealed ZnO films except for the film deposited at 300 watt. More significantly, it was found that annealed thin films showed the resistivity in the range of 10{sup −3} ∼ 10{sup −4} ohm-cm. Such a high optical transmittance and conducting zinc-oxide thin film can be used as a window layer in solar cell.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of sputtering power on structural, mechanical and photoluminescence properties of nanocrystalline SiC thin films

In the present study, SiC thin films were deposited on Si (100) substrate by magnetron sputtering using a 4N purity commercial SiC target in argon atmosphere. The effect of sputtering RF power (140-170W) on structural, mechanical and photoluminescence properties were systematically studied by X-ray diffraction, field emission scanning electron microscopy, Nanoindentation and Spectrophotometer respectively. X-ray diffraction shows polycrystalline 4H-SiC phase with (105) preferred orientation and an enhancement in crystallite size with increasing power was also observed. The decrement in hardness and Young’s modulus with increment in RF power was ascribed to Hall-Petch relation. The maximum hardness and Young’s modulus were found to be 32 GPa and 232 GPa respectively. The photoluminescence spectra show peaks at 384 nm (3.22 eV) which corresponds to bandgap of 4H-SiC (phonon assisted band to band recombination) and 416 nm (2.99 eV) may be attributed to defect states and intensity of both peaks decreases as power increases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis and annealing study of RF sputtered ZnO thin film

In this paper, we have investigated the annealing effect on optical and structural properties of ZnO thin films, synthesized by RF magnetron sputtering. ZnO thin films were deposited on glass and silicon substrates simultaneously at a substrate temperature of 300 °C using Argon gas in sputtering chamber. Thickness of as deposited ZnO thin film was found to be ~155 nm, calculated by Rutherford backscattering spectroscopy (RBS). These films were annealed at 400 °C and 500 °C temperature in the continuous flow of oxygen gas for 1 hour in tube furnace. X-ray diffraction analysis confirmed the formation of hexagonal wurtzite structure of ZnO thin film along the c-axis (002) orientation. Transmittance of thin films was increased with increasing the annealing temperature estimated by UV-visible transmission spectroscopy. Quality and texture of the thin films were improved with annealing temperature, estimated by Raman spectroscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and optical characterization of terbium doped ZnGa{sub 2}O{sub 4} thin films deposited by RF magnetron sputtering

Tb{sup 3+} doped ZnGa{sub 2}O{sub 4} nanophosphor (21 nm) has been synthesized via low temperature polyol route and subsequently thin films of the same were deposited on glass and ITO substrates by RF magnetron sputtering. The films were characterized by X-ray Diffraction and luminescence measurements. The XRD pattern showed that Tb{sup 3+} doped ZnGa{sub 2}O{sub 4} nanophosphor has a cubic spinel phase. Luminescence behavior of the nanophosphor and as deposited sputtered film was investigated. The PL emission spectra of nanophosphor gave a broad ZnGa{sub 2}O{sub 4} host emission band along with a strong terbium emission and the thin films showed only broad host emission band and there was no terbium ion emission.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Novel high power impulse magnetron sputtering enhanced by an auxiliary electrical field

The high power impulse magnetron sputtering (HIPIMS) technique is a novel highly ionized physical vapor deposition method with a high application potential. However, the electron utilization efficiency during sputtering is rather low and the metal particle ionization rate needs to be considerably improved to allow for a large-scale industrial application. Therefore, we enhanced the HIPIMS technique by simultaneously applying an electric field (EF-HIPIMS). The effect of the electric field on the discharge process was studied using a current sensor and an optical emission spectrometer. Furthermore, the spatial distribution of the electric potential and electric field during the EF-HIPIMS process was simulated using the ANSYS software. The results indicate that a higher electron utilization efficiency and a higher particle ionization rate could be achieved. The auxiliary anode obviously changed the distribution of the electric potential and the electric field in the discharge region, which increased the plasma density and enhanced the degree of ionization of the vanadium and argon gas. Vanadium films were deposited to further compare both techniques, and the morphology of the prepared films was investigated by scanning electron microscopy. The films showed a smaller crystal grain size and a denser growth structure when the electric field was applied during the discharge process.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗