Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SLAG”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Phase assemblage of composite cements

The phase assemblage of binary Portland cements with 45 wt% replacement by calcareous fly ash and slag has been investigated by experiment, mass balance and thermodynamic simulations. The input for these calculations was based on clinker reaction measured by XRD-Rietveld refinement, on SCM reaction measured by SEM-EDS full element mapping and on C-S-H composition by SEM-EDS point analyses. A sensitivity analysis estimates the uncertainty of determination of phase volume as at best ± 2 cm{sup 3}/100 cm{sup 3}, and thus of rather semi-quantitative character. The differences between experiment and calculations regarding AFt/AFm, C-S-H and portlandite were assessed. Gel/space ratios computed using the volumes of all hydrates showed a clear correlation to compressive strength, which was unaffected by the mix composition. This suggests that the type of hydrates formed has little or no influence on the compressive strength and that the key factor is the space filling.

36 MATERIALS SCIENCE↗

Towards ternary binders involving limestone additions — A review

The review summarises literature to examine the transition from portland limestone cement system to composite ternary binder systems involving limestone. Interest in limestone addition as an ideal component in multicomponent binder systems has surged as evident from the large volume of literature published in the recent past. A ternary blended system, with co-substitution of limestone, has the potential to complement the reaction of the supplementary cementitious materials (SCMs). The direct addition of limestone powder helps to attain higher substitution levels of portland cement clinker, improve early age properties, and supplement SCM's reactivity. However, the dilution of hydrates could hamper the long-term benefits. In this review, the interaction of fine limestone is classified and elaborated under two broad umbrellas: physical and chemical interactions. The physical interactions can manifest in three ways, namely, filler action, shearing action and improved packing, which alters reaction rate and extent at early ages. The chemical interactions also modify the reaction kinetics and phase assemblage due to nucleation of C-S-H on calcite surfaces, preservation of the ettringite phase and formation of carboaluminates. Two different forms of carboaluminate hydrates — hemicarboaluminate and mono-carboaluminate can be present in the hydrate matrix depending on the balance between carbonate ions and aluminates in the pore solution. Several factors such as replacement level, particle size, choice of SCM, its reactivity and reactive aluminates content, sulphate levels, curing temperature, and duration of curing can control the carboaluminate formation, reaction degree of SCMs and chemical interaction from limestone additions. A combination of physical and chemical effects makes fine limestone a potential material for co-substitution with aluminosilicate based SCMs, mainly fly ash, slag, and calcined clay. In this review, the factors affecting limestone-SCM composites are summarised based on a detailed literature survey. The effects of SCM-limestone cement composites on hydration kinetics, reaction chemistry, the reactivity of SCMs, the stability of hydrated phases, and contribution to the physical structure development and macroscopic properties by evaluating hydration and mechanical properties are discussed. The importance of AFm (Al{sub 2}O{sub 3}–Fe{sub 2}O{sub 3}-mono) phases in various deterioration mechanisms in concrete and their influence on performance characteristics in different exposure environment is critically appraised.

36 MATERIALS SCIENCE↗

Strategies for control and mitigation of efflorescence in metakaolin-based geopolymers

Efflorescence can be harmful to material performance as a consequence of microstructural changes due to leaching and carbonation of alkalis. This article identifies mechanisms of efflorescence in metakaolin-based geopolymers, and approaches to reduce free/mobile alkali cations and pore network connectivity, and hence reduce efflorescence. Mechanical, mass transport and microstructural properties are assessed in metakaolin-based geopolymer cements produced using different alkali concentrations in the alkali activator and substitution/addition of blast furnace slag, silica fume, calcium aluminate cement, silicone oil and a dispersive admixture. The most effective strategy to reduce efflorescence results from increasing Si/Al in the geopolymer gel by addition of soluble silicate, silica fume or silicone oil. Addition of calcium aluminate cement or a dispersive admixture also reduce efflorescence, but are less effective. These results confirm that efflorescence may be reduced by controlling the amount of soluble silicates and reducing free alkali cations in geopolymers, providing enhanced performance and durability.

36 MATERIALS SCIENCE↗

Effect of rice husk ash-derived activator on the structural build-up of alkali activated materials

Highlights: • Filtered and unfiltered sodium silicate solutions were synthesised from RHA. • The dissolution efficiency of RHA in NaOH solution was 76.3%. • RHA-derived activator showed a structural build-up comparable to the commercial activator in AAM pastes. • The undissolved residues in the unfiltered RHA-derived activator increased the yield stress. • Comparable compressive strength and early age gel formation were observed from both commercial and RHA-derived solutions. Waste-derived sodium silicates (SSs) were synthesised from rice husk ash (RHA) to produce alkali activated materials (AAMs) using fly ash and slag as precursors. The effects of these SSs on the structural build-up were investigated by monitoring the evolution of the viscoelasticity, ultrasonic pulse waves, setting time, and infrared spectra. Two types of RHA derived SSs (filtered SS and unfiltered SS) were prepared to investigate the effect of the undissolved residue on the hardening process. The derived SS contained a large portion of monomer silicate species. The results showed that the structural build-up mechanism was comparable between the AAMs activated by the filtered SS and a commercial SS. The unfiltered SS increased the yield stress of the paste by up to 10 times. However, the residues in the unfiltered SS had insignificant impacts on the gel formation and compressive strength when using identical SiO{sub 2}/Na{sub 2}O and Na{sub 2}O/binder ratios in the mix design.

36 MATERIALS SCIENCE↗

Jet flames of a refuse derived fuel

This paper is concerned with combustion of a refuse derived fuel in a small-scale flame. The objective is to provide a direct comparison of the RDF flame properties with properties of pulverized coal flames fired under similar boundary conditions. Measurements of temperature, gas composition (O{sub 2}, CO{sub 2}, CO, NO) and burnout have demonstrated fundamental differences between the coal flames and the RDF flames. The pulverized coals ignite in the close vicinity of the burner and most of the combustion is completed within the first 300 ms. Despite the high volatile content of the RDF, its combustion extends far into the furnace and after 1.8 s residence time only a 94% burnout has been achieved. This effect has been attributed not only to the larger particle size of fluffy RDF particles but also to differences in RDF volatiles if compared to coal volatiles. Substantial amounts of oily tars have been observed in the RDF flames even though the flame temperatures exceeded 1300 C. The presence of these tars has enhanced the slagging propensity of RDF flames and rapidly growing deposits of high carbon content have been observed. (author)

09 BIOMASS FUELS↗

Mass spectrometric investigations on the release of inorganic species during gasification and combustion of German hard coals

Na-, K-, Cl-, and S-species released during thermal conversion of coal can cause several problems such as fouling, slagging and corrosion, especially in gas turbines and heat recovery systems. To reduce this problems an enhanced understanding of the underlying release mechanisms for Na-, K-, Cl-, and S-species is needed. Therefore, basic investigations have been performed in an atmospheric lab-scale tube furnace at 1400 C under gasification and combustion conditions. Hot gas analysis has been carried out by molecular beam mass spectrometry. The release of H{sub 2}S, HCl, K+, NaCl, COS, and SO{sub 2} has been qualitative and quantitative analysed and correlated with the coal composition. The results show a strong dependence of coal composition and reaction atmosphere on the release of Na-, K-, Cl-, and S-species. Additionally, thermodynamic equilibrium calculations with the software package FactSage 5.4.1 have been undertaken for comparison with the experimental results. (author)

01 COAL, LIGNITE, AND PEAT↗

Sulfuric Acid Improves the Reactivity of Zeolites via Dealumination

The demand for supplementary cementitious materials (SCMs), like fly ash, slag, and silica fume, is projected to rise over the next few decades. However, global decarbonization efforts, such as decommissioning of coal-fired power plants, will limit the supply of SCMs. Therefore, alternative SCM sources are a critical need for the cement and concrete industry. However, the high crystallinity of zeolites limits their pozzolanic reactivity. The goal of this work was to improve the reactivity of two common zeolites, namely clinoptilolite and SSZ-13, by treating them with sulfuric acid. The treatment enhanced zeolite reactivity via dealumination and decreased particle sizes, which led to increased reactivity with calcium hydroxide, as indicated by a 42.0% increase in reaction heat measured by isothermal calorimetry. Here, we elucidate mechanistic understanding that smaller particle sizes induced by acid treatment accelerated peak heat evolution, while free aluminates from dealumination increased heat via direct reaction with aqueous Ca 2+ .

36 MATERIALS SCIENCE↗

Application of air classification and formulation to manage feedstock cost, quality and availability for bioenergy

Biomass such as agricultural residues, energy crops and yard waste has significant potential to be used as renewable feedstocks for production of fuels, chemicals and energy. However, in a given location, biomass availability, cost and quality can vary markedly. Strategies to manage these traits must be identified and implemented so that consistent low-cost and high-quality feedstocks can be delivered to biorefineries year round. In this study, we examine air classification as a method to mitigate high ash concentrations in corn stover, switchgrass, and grass clippings. Formulation techniques were then used to produce blends that met ash quality and biomass quantity specifications at the lowest possible cost for biopower and biochemical conversion applications. It was found that air classification can separate the biomass into light fractions which contain concentrated amounts of elemental ash components introduced through soil contamination such as sodium, alumina, silica, iron and titania; and heavy fractions that are depleted in these components and have relatively lower total ash content. Light fractions of corn stover and grass clippings were found to be suitable for combustion applications since they had less propensity to slag than the whole biomass material. The remaining heavy fractions of corn stover or grass clippings could then be blended with switchgrass to produce blends that met the 5% total ash specifications suggested for biochemical conversions. However, ternary blends of the three feedstocks were not possible due to the high ash content of grass clippings. Lastly, it was determined that air classification by itself was not suitable to prepare these feedstocks for pyrolysis due to high ash content.

09 BIOMASS FUELS↗

Bioleaching to produce clean loblolly pine for thermochemical conversion

Lignocellulosic biomass contains inorganic elements that could induce slagging, ash fouling, and emission of both corrosive and harmful gases during thermochemical conversion. Water leaching pretreatment can remove most of the water-soluble elements, while it has limited industrial applicability due to its ineffectiveness in removing water-insoluble elements. Bioleaching is an alternative pretreatment method which has not been fully studied. In this work, bioleaching by Aspergillus niger strains NRRL 2001, NRRL 3122, and NRRL 567 was conducted to pretreat loblolly pine biomass with added water. Further, the removal of inorganic elements (K, Ca, Mg, and S) by bioleaching with A. niger NRRL 2001 was compared with chemical leaching with citric acid, HCl, and NaOH. It was shown that the pH reduction during bioleaching greatly improved K and Mg leaching to the point comparable to acid leaching, whereas Ca was precipitated by oxalic acid produced by the fungus. Bioleaching was also conducted in manually separated needles and chips components of loblolly pine. Glucose was added at different levels to assist bioleaching. At higher glucose levels, gluconic acid and citric acid were produced during bioleaching, leading to the increase of K, Ca, and Mg removal rates by more than 35%, 180%, and 390%, respectively, from the feedstock as compared with water leaching. Overall, bioleaching greatly improved removal of K, Ca, Mg, but not S from loblolly pine feedstocks as compared with water leaching.

09 BIOMASS FUELS↗

Carbon dioxide integration into alkali aluminosilicate cement particles for achievement of improved properties

Alkali aluminosilicate cement developed using ground granulated blast furnace slag was produced mechanochemically in the presence of lime and sodium hydroxide. Processing of this cement in a carbon dioxide environment led to the incorporation of carbon dioxide into the resultant hydraulic cement as metastable carbonate complexes. The hydration reactions of cement were complemented with formation of crystalline carbonates; the resultant hydrates and carbonates made synergistic contributions towards the binding effects and stability of the inorganic binder. Analytical chemistry and physical test methods were performed on cements and their hydrates in order to understand the form of carbon dioxide in their corresponding structures. Here the test results indicated that carbon dioxide was integrated into the cement particles in metastable form, which formed carbonate crystallites integrated with the amorphous hydrates in the course of hydration of cement. This phenomenon led to significant improvements in the mechanical properties of the resulting binder.

54 ENVIRONMENTAL SCIENCES↗

Zinc aluminate (ZnAl 2 O 4 ) refractory aggregates: Dilatometric sintering studies and thermal expansion coefficient

ZnAl 2 O 4 has recently been reported to enhance thermomechanical properties and slag corrosion resistance of refractory castables. The pore generation and deleterious expansion during in situ ZnAl 2 O 4 formation can limit their amount in a refractory composition. A comprehensive dilatometric study is presented, identifying the optimum raw materials and processing conditions. Preformed ZnAl 2 O 4 refractory aggregates were synthesized from industrial ZnO and reactive Al 2 O 3 by two-stage firing at 1050 °C and 1700 °C resulting in 0% open porosity. The ZnAl 2 O 4 powder calcined at 1050 °C is also a good refractory matrix material as it has better sinterability than preformed refractory-grade MgAl 2 O 4 and calcined alumina. The thermal expansion coefficient of ZnAl 2 O 4 aggregate in the range of 70–1600 °C was found to be 10.7 × 10 –6 K –1 , which is similar to tabular Al 2 O 3 (10.3 × 10 –6 K –1 ) and MgAl 2 O 4 (10.3 × 10 –6 K –1 ), but lower than dead burned MgO (16.4 × 10 –6 K –1 ), creating the possibility of developing thermal shock resistant refractories by utilizing this mismatch.

36 MATERIALS SCIENCE↗

Chrome-free qandilite (Mg 2 TiO 4 ) refractory aggregates: Role of titania source and evaluation of thermal expansion coefficient

As used chrome-based refractories may contain toxic Cr 6+ , the chrome-free Mg 2 TiO 4 phase is being considered which is known to improve hot strength and resistance to thermal shock and slag corrosion. As in situ Mg 2 TiO 4 formation generates porosity, preformed aggregates are desirable. Dilatometric studies revealed that when dead burned magnesia is combined with industrial anatase instead of rutile, it expanded less (1% versus 7.2%) and the reaction occurred earlier (965°C compared to 1120°C). After sintering at 1,600°C, rutile produced an aggregate with 3.8% open porosity, whereas anatase led to 0 % porosity and a bulk density of 3.24g/cm 3 with a thermal expansion coefficient (70–1,600°C) of 13.5×10 -6 K -1 . Moreover, replacing rutile by anatase eliminates the undesirable MgTiO 3 phase. The anatase-based aggregate consisted of a Mg 2 TiO 4 matrix with residual unreacted MgO and an intergranular, refractory CaTiO 3 phase. In conclusion, the rutile-based aggregate was deemed unsuitable due to a low-melting microstructure of forsterite contiguous with CaTiO 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of a Messer – The late-Medieval single-edged sword of Central Europe

Metallurgical characterization of a sword blade fragments dating from the second half of the 15th century found in central Slovenia was performed in order to determine its chemical composition, microstructure, microhardness, and to obtain insight into the methods of manufacture of a late-medieval Messer sword. As the artefact was broken, examinations were limited to six very small fragments that were allowed to be removed from the cutting edge, core and the back of the blade. Light optical microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, energy dispersive X-ray fluorescence spectrometry, differential scanning calorimetry, thermodynamics approach and Vickers micro-hardness tests were employed to analyze the microstructure and mechanical properties. The results show that the sword was manufactured from a single wrought iron billet. The surface of the sword was carburized. No evidence of quenching was found. The ferritic microstructure is concentrated in the core, and the pearlitic in the outer layer of the blade. All metal fragments contained non-metallic inclusions that were derived mostly from slag and some from hammer scale. - Highlights: • A metallurgical characterization of a medieval sword blade has been performed. • The carbon content decreased from the surface to the core of the blade. • The dominant microstructure in the outer layer is pearlite and in the core is ferrite. • The presence of lump shaped and elongated non-metallic inclusions was observed. • The sword was manufactured from a single wrought iron billet.

36 MATERIALS SCIENCE↗

Characterisation of a complex thin walled structure fabricated by selective laser melting using a ferritic oxide dispersion strengthened steel

Oxide dispersion strengthened (ODS) alloys exhibit superior mechanical and physical properties due to the presence of nanoscopic Y(Al, Ti) oxide precipitates, but their manufacturing process is complex. The present study is aimed at further investigation of the application of an alternative, Additive Manufacturing (AM) technique, Selective Laser Melting (SLM), to the production of consolidated ODS alloy components. Mechanically alloyed PM2000 (ODS-FeCrAl) powders have been consolidated and a fine dispersion of Y-containing precipitates were observed in an as built thin-walled component, but these particles were typically poly-crystalline and contained a variety of elements including O, Al, Ti, Cr and Fe. Application of post-build heat treatments resulted in the modification of particle structures and compositions; in the annealed condition most precipitates were transformed to single crystal yttrium aluminium oxides. During the annealing treatment, precipitate distributions homogenised and localised variations in number density were diminished. The resulting volume fractions of those precipitates were 25–40% lower than have been reported in conventionally processed PM2000, which was attributed to Y-rich slag-like surface features and inclusions formed during SLM. - Highlights: • A wall structure was grown from ODS steel powder using selective laser melting. • A fine dispersion of nano-precipitates was apparent in as-build material. • Precipitates were multi-phased containing several elements, e.g. O, Ti, Al, Fe, Cr, Y. • Post-build annealing changed those into typically single-crystalline Y–Al–O. • The anneal also reduced and stabilised the volume fraction of precipitates to ~ 0.006.

36 MATERIALS SCIENCE↗

Exploring the structure of high temperature, iron-bearing liquids

This paper describes the direct measurements of the structure of iron-bearing liquids using a combination of containerless techniques and in–situ high energy x-ray diffraction. These capabilities provide data that is important to help model and optimize processes such as smelting, steel making, and controlling slag chemistry. A successful programme of liquid studies has been undertaken and the Advanced Photon Source using these combined techniques which include the provision of gas mixing and the control of pO₂ and the changing influence of mixed valance elements. It is possible to combine rapid image acquisition with quenching of liquids to obtain the full diffraction patterns of deeply supercooled liquids and the metastable supercooled liquid regime, where the liquid structures and viscosity change most dramatically, can also be explored.

36 MATERIALS SCIENCE↗

Integrated modeling methodology for ash agglomeration in poly-disperse fluidized beds using particle population framework

This article discusses a unique agglomeration modeling methodology developed based on binary collisions to combine the effects of heterogeneity in ash chemistry and granular physics. A simple population balance is defined to find changes in the particle size distribution (PSD) of a fluidized bed. Thermodynamic equilibrium calculations and a computational fluid dynamics (CFD) code, are used to obtain hydrodynamic parameters. A method to calculate and use a distribution of collision frequencies in fluidized beds, corresponding to a poly-disperse particle size distribution, was developed in order to incorporate the particle level heterogeneities. A distribution of collision frequencies obtained for poly-dispersed particles showed a three orders of magnitude higher collision frequency amongst the smaller particles than the coarser ones, at the initiation of agglomeration. Ash agglomeration occurred when the slag amount (binder) was less than 10 wt% at temperatures <850 °C for Pittsburgh No. 8 coal.

42 ENGINEERING↗

Use of Brazilian sugarcane bagasse ash in concrete as sand replacement

Sugarcane today plays a major role in the worldwide economy, and Brazil is the leading producer of sugar and alcohol, which are important international commodities. The production process generates bagasse as a waste, which is used as fuel to stoke boilers that produce steam for electricity cogeneration. The final product of this burning is residual sugarcane bagasse ash (SBA), which is normally used as fertilizer in sugarcane plantations. Ash stands out among agroindustrial wastes because it results from energy generating processes. Many types of ash do not have hydraulic or pozzolanic reactivity, but can be used in civil construction as inert materials. The present study used ash collected from four sugar mills in the region of Sao Carlos, SP, Brazil, which is one of the world's largest producers of sugarcane. The ash samples were subjected to chemical characterization, sieve analysis, determination of specific gravity, X-ray diffraction, scanning electron microscopy, and solubilization and leaching tests. Mortars and concretes with SBA as sand replacement were produced and tests were carried out: compressive strength, tensile strength and elastic modulus. The results indicated that the SBA samples presented physical properties similar to those of natural sand. Several heavy metals were found in the SBA samples, indicating the need to restrict its use as a fertilizer. The mortars produced with SBA in place of sand showed better mechanical results than the reference samples. SBA can be used as a partial substitute of sand in concretes made with cement slag-modified Portland cement.

09 BIOMASS FUELS↗

Effect of sewage sludge content on gas quality and solid residues produced by cogasification in an updraft gasifier

Highlights: Black-Right-Pointing-Pointer Cogasification of sewage sludge with wood pellets in updraft gasifier was analysed. Black-Right-Pointing-Pointer The effects of sewage sludge content on the gasification process were examined. Black-Right-Pointing-Pointer Sewage sludge addition up to 30 wt.% reduces moderately the process performance. Black-Right-Pointing-Pointer At high sewage sludge content slagging and clinker formation occurred. Black-Right-Pointing-Pointer Solid residues produced resulted acceptable at landfills for non-hazardous waste. - Abstract: In the present work, the gasification with air of dehydrated sewage sludge (SS) with 20 wt.% moisture mixed with conventional woody biomass was investigated using a pilot fixed-bed updraft gasifier. Attention was focused on the effect of the SS content on the gasification performance and on the environmental impact of the process. The results showed that it is possible to co-gasify SS with wood pellets (WPs) in updraft fixed-bed gasification installations. However, at high content of sewage sludge the gasification process can become instable because of the very high ash content and low ash fusion temperatures of SS. At an equivalent ratio of 0.25, compared with wood pellets gasification, the addition of sewage sludge led to a reduction of gas yield in favor of an increase of condensate production with consequent cold gas efficiency decrease. Low concentrations of dioxins/furans and PAHs were measured in the gas produced by SS gasification, well below the limiting values for the exhaust gaseous emissions. NH{sub 3}, HCl and HF contents were very low because most of these compounds were retained in the wet scrubber systems. On the other hand, high H{sub 2}S levels were measured due to high sulfur content of SS. Heavy metals supplied with the feedstocks were mostly retained in gasification solid residues. The leachability tests performed according to European regulations showed that metals leachability was within the limits for landfilling inert residues. On the other hand, sulfate and chloride releases were found to comply with the limits for non-hazardous residues.

54 ENVIRONMENTAL SCIENCES↗