Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHIELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The importance of delayed neutron precursors in gamma dose calculations for activated primary heat exchanger components in the Molten Salt Breeder Reactor

The Molten Salt Reactor (MSR) Multiphysics Applications technical area in the Nuclear Energy Advanced Modeling and Simulation program has supported the development of 3D Monte Carlo models of the Molten Salt Breeder Reactor (MSBR) over the last couple of years. This MSBR model was previously run with the Shift Monte Carlo code to perform radiation shielding calculations in the reactor cell area. The MSBR is a 2250 MWth (1000 MWe) liquid-fueled molten salt reactor design developed at Oak Ridge National Laboratory in the 1970s. Determining the source terms from activated primary heat exchanger (HX) components is important because delayed and prompt neutron fluxes incident on these components affect the dose rate in the primary HX maintenance areas. This information can be used in the development of remote handling procedures required during shutdown for maintenance. A methodology has been developed and is proposed in this paper to quantify the activated source term from the primary HX components as a result of the movement of the delayed neutron precursors in flowing primary fuel salt through the primary HXs in the MSBR. The goal of this research is to evaluate the gamma dose rates in the maintenance hatches above the primary HX using the activated HX source terms. The study showed that the gamma dose rates are approximately two orders of magnitudes higher when accounting for the neutron activation from the movement of delayed neutron precursors through the HXs than when flowing fuel is not considered. Thus, the movement of delayed neutron precursors must be taken into account for accurately predicting the neutron activation of primary loop components.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Critical response to M. Worrall et al. Published in Annals of Nuclear Energy 207 (2024) 110731

M. Worrall et al. recently published a manuscript titled “Fast neutron irradiation capability in existing thermal test reactors” (Worrall, 2024) that summarizes an irradiation vehicle design that would boost the fast neutron flux in the Advanced Test Reactor (ATR) for testing of nonfuel materials in a neutron flux energy spectrum that is more representative of fast reactors. Here, the authors compare their design with a separate vehicle design that they conceived of that would be implemented within the High Flux Isotope Reactor (HFIR). They analyzed both designs and drew conclusions on the most realistic near-term options for shielded nonfuel material irradiations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Reduced-order modeling for efficient cross section library development in high-temperature gas reactor pebble-bed depletion analysis

Accurate modeling of running-in and equilibrium conditions in pebble-bed reactors (PBRs) requires precise microscopic multigroup neutron cross sections. In Griffin, deterministic neutronics calculations rely on multivariate interpolation over large cross section libraries, resulting in significant memory usage and performance bottlenecks. This work, together with a companion paper on Griffin integration, explores reduced-order models (ROMs) to replace interpolation with lightweight surrogates. Several ROM techniques are benchmarked, with deep neural networks (DNNs) demonstrating superior memory efficiency, scalability, and predictive accuracy. A total of 295 DNNs were trained to build a comprehensive isotope library, integrated into Griffin through a custom LibTorch interface for depletion analysis. Initial results demonstrate that DNN-based ROMs drastically reduce memory demands while preserving accuracy, enabling finer tabulations and additional state variables without overhead. In conclusion, the framework also supports online cross section generation and real-time DNN updates through transfer learning, improving fidelity by capturing self-shielding and evolving nuclide compositions during burnup.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Investigation of irradiation damage and heat deposition: a comparative analysis for HEU-to-LEU conversion in HFIR

The planned conversion of the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory from highly enriched uranium (HEU) to low-enriched uranium (LEU) fuel requires detailed evaluation of experiment-relevant parameters to ensure continued performance for materials testing and isotope production. Here, this study presents the first comprehensive assessment of displacements per atom (dpa) and heat deposition rates in target materials within the HFIR flux trap with both HEU and candidate LEU core configurations. Seven analyses were conducted to evaluate key performance metrics, including fast neutron flux distribution, cross section response functions, cross section data, and local dpa and heat deposition rates using mesh- and cell-based tallies. Simulations employed Shift, Monte Carlo N-Particle (MCNP), and the HIFR Controller (HFIRCON) tool suite for high-fidelity transport and depletion modeling. The LEU designs—using U 3 Si 2 -Al dispersion fuel and operating at 95 MW—were compared to the current 85 MW HEU configuration. Results show that while the candidate LEU cores exhibit higher dpa rates due to a harder spectrum and extended cycle lengths, they also demonstrate reduced heat deposition rates in irradiation experiments, primarily due to increased gamma self-shielding from higher 238 U content in the core. These findings confirm that LEU conversion can maintain HFIR’s materials irradiation capabilities but may require redesigning existing experimental hardware.

HEU↗
DOE OSTI2020

Self-aligned concentrating immersion-lens arrays for patterning and efficiency recovery in scaffold-reinforced perovskite solar cells

In contrast to existing silicon, CIGS, and multi-junction cells that exhibit remarkable mechanical durability, perovskite solar cells have been shown to delaminate when subjected to the mechanical loads that occur during processing and field exposures, limiting their potential as a reliable solar technology. Mechanical reinforcement is thus essential for durable and reliable perovskite technologies. One current strategy to overcome the thermomechanical fragility of perovskite solar cells is to extrinsically shield them by introducing reinforcing scaffolds which partition the cell into many distinct microcells, but improvements in mechanical stability coincide with a reduced device efficiency due to parasitic absorption by the scaffold. We address this reduced efficiency by integrating concentrating immersion-lens arrays (CILAs) into scaffold-reinforced solar cells. These scaffolds are lithographically patterned by a maskless process, in which ultraviolet light is used to pattern the scaffolds through the CILAs, ensuring self-alignment and optical contact with the microcells. Perovskite devices are deposited into the microcells, and during operation, light is concentrated into the microcells and away from the insulating scaffolds, resulting in mechanically resilient solar cells with efficiencies comparable to planar devices. The CILAs also exhibit passive tracking of incident light—verified experimentally and with ray-tracing simulations—which is critical for optimal power output as the sun moves across the sky during the day. The simplicity of the fabrication process and the efficiency of the resulting scaffolded devices show that a lens-integrated scaffold-reinforced structure is a potential pathway to high-performance, robust, commercially viable perovskite solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

Traction-separation response of bilayer graphene interfaces: The role of an intercalated single atomic layer of water molecules and hydroxyl groups

Molecular dynamics simulations of the normal and shear traction-separation response of dry and wet bilayer graphene interfaces were performed. The influence of a single, atomic layer of water molecules sandwiched between graphene layers and hydroxyl functionalization on one or both layers were investigated. Hydroxyl groups provided a shielding effect during normal separation while favoring stick-slip friction under sliding conditions. The single, atomic layer of water molecules confined between hydrophilic and asymmetric hydrophobic/hydrophilic surfaces was found to ease sliding friction. The mechanisms arose from the balance between the attractive and repulsive graphene/water interactions through bridges of single water molecules between the two surfaces and the structure of the water monolayer under confinement for which an out-of-plane water/water hydrogen bond network could not be developed. The single, atomic layer of water molecules reduced the sliding friction the most when both surfaces were hydrophilic and lowered the sliding friction of the asymmetric hydrophobic/hydrophilic interfaces to that when both surfaces were hydrophobic. An optimal hydroxyl surface coverage of less than 10% may exist for efficient water lubrication, with diminishing effect with increasing number of hydroxyl groups. Finally, the findings offer a design strategy for assembling bilayer graphene interfaces with tailored friction and sliding contact properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Measurement of the gamma ray background in the Davis cavern at the Sanford Underground Research Facility

Deep underground environments are ideal for low background searches due to the attenuation of cosmic rays by passage through the earth. However, they are affected by backgrounds from γ -rays emitted by 40 K and the 238 U and 232 Th decay chains in the surrounding rock. The LUX-ZEPLIN (LZ) experiment will search for dark matter particle interactions with a liquid xenon TPC located within the Davis campus at the Sanford Underground Research Facility, Lead, South Dakota, at the 4850-foot level. In order to characterise the cavern background, in-situ γ -ray measurements were taken with a sodium iodide detector in various locations and with lead shielding. The integral count rates (0–3300 keV) varied from 596 Hz to 1355 Hz for unshielded measurements, corresponding to a total flux from the cavern walls of 1.9 ± 0.4 γ cm −2 s −1 . The resulting activity in the walls of the cavern can be characterised as 220 ± 60 Bq/kg of 40 K, 29 ± 15 Bq/kg of 238 U, and 13 ± 3 Bq/kg of 232 Th.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

The carboxylation status of osteocalcin has important consequences for its structure and dynamics

The carboxylation status of Osteocalcin (Ocn) not only influences formation and structure in bones but also has important endocrine functions affecting energy metabolism and expenditure. In this study, the role of γ-carboxylation of the glutamate residues in the structure-dynamics-function relationship in Ocn is investigated. Three forms of Ocn, differentially carboxylated at the Glu-17, 21 and 24 residues, along with a mutated form of Ocn carrying Glu/Ala mutations, are modeled and simulated using molecular dynamics (MD) simulation in the presence of calcium ions. Characterization of the global conformational dynamics of Ocn, described in terms of the orientational variations within its 3-helical domain, highlights large structural variations in the non-carboxylated osteocalcin (nOcn). The bi-carboxylated Ocn (bOcn) and tri-carboxylated (tOcn) species, in contrast, display relatively rigid tertiary structures, with the dynamics of most regions strongly correlated. Radial distribution functions calculated for both bOcn and tOcn show long-range ordering of the calcium ion distribution around the carboxylated glutamate (γGlu) residues, likely playing an important role in promoting stability of these Ocns. Additionally, the same calcium ions are observed to coordinate with neighboring γGlu, better shielding their negative charges and in turn stabilizing these systems more than do the singly coordinating calcium ions observed in the case of nOcn. bOcn is also found to exhibit a more helical C-terminal structure, that has been shown to activate its cellular receptor GPRC6A, highlighting the allosteric role of Ocn carboxylation in modulating the stability and binding potential of the active C-terminal. Furthermore, the carboxylation status of Ocn as well and its calcium coordination appear to have a direct influence on Ocn structure and dynamics, possibly leading to the known differences in Ocn biological function.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A new hypothesis for air loss in cement systems containing fly ash

Although there are many benefits gained from incorporating fly ash into concrete, carbon contamination in the fly ash has been shown to interfere with the efficacy of organic additives in an unpredictable manner. This work uses surface tension measurements to quantify the adsorption of air-entraining agents (AEA) onto cement and fly ash. Both the adsorption capacity of the adsorbents and the adsorption isotherms indicate that the fly ash particles, rather than the carbon itself, dominate adsorption in a carbon-contaminated ash in cement pore solution. We propose that adsorption onto fly ash particles and cement actually improve air entrainment via Pickering stabilization. While the carbon is still expected to contribute to air loss via hydrophobic adsorption of the surfactants, we suggest that the primary way in which the carbon interferes is by shielding surfactant-coated fly ash particles from participating in air development and Pickering stabilization during mixing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Corrosion integrity of oil cement modified by environment responsive microspheres for CO2 geologic sequestration wells

In order to ensure the safe and effectiveness of CO{sub 2} geological storage, an environmental responsive polymer microspheres (ERPM) was prepared to improve the corrosion resistance of cement stone. The structure and environmental response characteristics of ERPM were characterized, and then the anti-corrosion performance and anti-corrosion mechanism for ERPM were discussed. The results shown that ERPM had good environmental response characteristics and temperature resistance. ERPM could effectively suppressed the corrosion rate and the damage degree of mechanical properties of cement stone. The corrosion integrity of cement stone was improved due to the acidic response characteristic and form polymer films of ERPM, which effectively shield the direct contact between corrosion medium and hydration products.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the moisture migration of concrete subject to high temperature with different heating rates

A better understanding of moisture migration in concrete at high temperature can play an important role to improve the fire-resistance and radiation-shielding capability of concrete structures. In this regard, within the numerical framework of Multi-physics Lattice Discrete Particle Model, the moisture clog in concrete during heating is defined as the moisture-saturated region between the so-called “water front” and “water back” (isosurfaces of saturation = 1). The moisture migration in concrete subject to slow and fast heating has been investigated by simulating experimental tests in which moisture has been monitored via different techniques, namely 3D Neutron Tomography and Ground-Penetrating Radar. An overall consistency between experimental and numerical results has been observed, indirectly proving the effectiveness of numerical modelling and experimental monitoring of moisture migration.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ultra-high gamma irradiation of calcium silicate hydrates: Impact on mechanical properties, nanostructure, and atomic environments

The concrete biological shield in a nuclear power plant receives ~100–200 MGy gamma dosage during an 80-year design life. However, precise changes in the mechanical properties and atomic environments of C-S-H at ultrahigh irradiation dosages have not been systematically documented. Here, we report that irradiation decreases C-S-H basal spacing (~ 0.6 ± 0.1 Å for 189 MGy) and increases its Young's modulus, which is attributed to the lower basal spacing as the nano porosity potentially increased and microporosity remained unchanged. Irradiation also decreased the molecular water content and increased hydroxyl groups in C-S-H, showing that interlayer water removal reduces the basal spacing. Finally, 1 H and 29 Si NMR results indicate some disorder in the local proton CaO-H species and slight depolymerization of the silicate structure. Together, these results indicate that the C-S-H gel stiffens upon ultrahigh gamma irradiation dosage, a finding which concerns long-term nuclear power plants operations worldwide.

1H NMR↗
DOE OSTI2023

Virion glycosylation influences mycobacteriophage immune recognition

Glycosylation of eukaryotic virus particles is common and influences their uptake, trafficking, and immune recognition. In contrast, glycosylation of bacteriophage particles has not been reported; phage virions typically do not enter the cytoplasm upon infection, and they do not generally inhabit eukaryotic systems. We show here that several genomically distinct phages of Mycobacteria are modified with glycans attached to the C terminus of capsid and tail tube protein subunits. These O-linked glycans influence antibody production and recognition, shielding viral particles from antibody binding and reducing production of neutralizing antibodies. Glycosylation is mediated by phage-encoded glycosyltransferases, and genomic analysis suggests that they are relatively common among mycobacteriophages. Putative glycosyltransferases are also encoded by some Gordonia and Streptomyces phages, but there is little evidence of glycosylation among the broader phage population. The immune response to glycosylated phage virions in mice suggests that glycosylation may be an advantageous property for phage therapy of Mycobacterium infections.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Influence of ion-pairing reagents on the separation of intact glycoproteins using hydrophilic-interaction liquid chromatography - high-resolution mass spectrometry

Hydrophilic-interaction liquid chromatography (HILIC) of intact proteins offers high-resolution separations of glycoforms of glycoproteins differing in the number of (neutral) glycans. However, to obtain efficient separations it is essential that the positively charged sites of the proteins are shielded by acidic (negative) ion-pair reagents (IPRs), so as to enhance the contribution of the hydroxyl groups of the (neutral) sugars in the glycoprotein. Here, we studied the influence of various IPRs that differ in physico-chemical properties, such as hydrophobicity and acidity, on the capillary-scale HILIC separation of intact (glyco)proteins. We evaluated the use of fluoroacetic acid (MFA), difluoroacetic acid (DFA), trifluoroacetic acid (TFA), and heptafluorobutyric acid (HFBA) as diluents for sample preparation, as solvents for sample loading on a reversed-phase trap prior to the HILIC separation, and as mobile-phase components for HILIC and HILIC-MS. To reduce the contribution of ion-exchange interaction with the (silica-based) stationary phase, we used an acrylamide-based monolithic column. We studied the influence of the different IPRs on each step of the separation of a mixture of proteins of different size and hydrophilicity and on the separation of the five glycoforms of ribonuclease B. The content of IPR in the sample was shown not to affect the separation and the MS detection. However, a low content of TFA and DFA in the mobile phase is favourable, as it reduces adduct formation and leads to higher signal intensity. The optimized HILIC conditions successfully resolved nine major glycoforms groups of a ~40 kDa glycoprotein horseradish peroxidase (HRP), as an example of a complex glycoprotein.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Extracting single fiber transverse and shear moduli from off-axis misalignment fiber tensile testing

Small diameter (<100 μm) fibers (e.g. carbon fibers, Kevlar, and fiberglass) and wires (e.g. ultrafine copper and aluminum wires) are frequently used in many different engineering applications, such as for light weighting structures, electromagnetic shielding for aircraft/infrastructure/EVs, vibration damping, biological sensors, aerospace electrical devices, and electric windings just to name a few. Due to the manufacturing process, the fibers and wires are pulled and stretched to produce a preferential alignment. Therefore, thin fibers and wires typically display different properties along the length of the fiber as opposed to their cross section and many fibers/wires are considered transversely isotropic. The axial properties of fibers/wires can be ascertained via tensile testing of single-filaments or fiber tows, but the radial properties require much more effort to measure. Knowing these properties is important for the accurate prediction of micromechanical models and manipulation of fibers during micromanufacturing. In this paper, a new technique was developed to determine the transverse/shear moduli and strength of a material by conducting tensile tests of the material at increasing misalignment angles from the tensile axis. Due to the transversely isotropic nature of the material, the transverse/shear moduli and strength influence the experimental results recorded by the test machine to different degrees based on the amount of misalignment in the test setup. An equation was derived to determine the influence of each of the material properties based on the misalignment angle by manipulating the stiffness matrix for transversely isotropic materials using the transformation matrices. Then, curve fitted coefficients were used to identify the material properties. Here, the strengths were similarly determined by curve fitting an off-axis Tsai-Hill failure criteria to determine the influence of transverse, shear, and tensile strengths based on the complex loading condition provided by the off-axis tensile test. Zoltek Panex 35 carbon fibers were used to demonstrate this new technique and the determined properties were then compared to those obtained from nanoindentation and from literature. Fracture surfaces provide insight into the different failure mechanisms at various misalignment angles.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A mesoscale 3D model of irradiated concrete informed via a 2.5 U-Net semantic segmentation

The concrete biological shield in light-water reactors is exposed to neutron and gamma irradiation, which deteriorates the concrete’s mechanical properties in the long term. To assess the irradiation-induced damage, predictive mechanical models are developed and used in parallel with the characterization of irradiated concrete samples. Realistic 3D simulation domains can drastically improve a model’s prediction. In this work, we utilized x-ray computed tomography (XCT) data of a concrete specimen to reconstruct its 3D microstructure. The XCT data shows low contrast between the concrete’s aggregates and cement paste, resulting in poor image segmentation when using traditional unsupervised techniques. To address this issue, we developed and trained a 2.5D U-Net model on only 24 pre-labeled XCT layers to segment 651 layers of the XCT data. The overall F1-score of the model is approximately 96%. Then, we created a 3D finite element (FE) mesh based on the stack of segmented images. The FE model contains radiation-induced expansion, damage, and creep. The constitutive equations are adapted to each phase (aggregates and cement paste). Here, we simulated the effects of neutron irradiation in the concrete specimen as well as the specimen’s mechanical response to uniaxial compression. Finally, model validation was performed using experimental data on similar concrete specimens in the literature.

2.5D U-Net↗
DOE OSTI2020

A redox-active organic cation for safer metallic lithium-based batteries

Safety concerns have severely impeded the practical application of high-energy-density lithium-based batteries. Dendrite growth and overcharging can lead to particularly catastrophic thermal failure. Here we report an organic cation, trisaminocyclopropenium (TAC), as a bi-functional electrolyte additive to suppress dendrite growth and offer reversible overcharge protection for metallic lithium-based batteries. During the Li plating process, TAC cations with aliphatic chains can form a positively charged electrostatic shield around Li protrusions, repelling the approaching Li + and thereby attaining a more uniform plating. A two times longer cycle life of 300 h at 1 mA cm -2 is achieved in a Li|Li symmetric cell in comparison with the control. During the overcharging process, the redox-active TAC can repeatedly shuttle between two electrodes, maintaining the cell voltage within a safe value. A solid protection of 117 cycles (~1640 h) at 0.2 C with a 100% overcharge is achieved in a LiFePO 4 /Li 4 Ti 5 O 12 cell. This study sheds fresh light on the ability of organic cations to build safer batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Measuring multiple cosmogenic nuclides in glacial cobbles sheds light on Greenland Ice Sheet processes

The behavior of the Greenland Ice Sheet during the Pleistocene remains uncertain due to the paucity of evidence predating the Last Glacial Maximum. In this study, we employ a novel approach, cosmogenic nuclide analysis of individual subglacially-derived cobbles, which allows us to make inferences about ice sheet processes and subglacial erosion. From three locations in western Greenland, we collected 86 cobbles from the current ice sheet margin and nine cobbles exposed on the modern proglacial land surface. We measured the concentration of in situ 10 Be in all cobbles (n = 95) and 26 Al and 14 C in a subset (n = 14). Cobbles deposited during Holocene retreat have 10 Be exposure ages generally consistent with the timing of ice retreat determined by other methods. Conversely, most of the 86 subglacial cobbles contain very low concentrations of 10 Be (median 1.0×10 3 atoms g –1 ), although several have ~10 4 and one has ~10 5 atoms g –1 . The low concentrations of 10 Be in most subglacial cobbles imply that their source areas under the Greenland Ice Sheet are deeply eroded, preserving minimal evidence of surface or near-surface exposure. The presence of measurable 14 C in ten of the cobbles requires that they experienced cosmogenic nuclide production within the past ~30 ka; however, 14 C/ 10 Be ratios of ~6 suggest that nuclide production occurred during shielding by overlying material. Only two of the 86 subglacial cobbles definitively have cosmogenic nuclide concentrations consistent with prior surface exposure. Overall, isotopic analysis of subglacial cobbles indicates that much of western Greenland's subglacial landscape is characterized by deep erosion and minimal subaerial exposure.

58 GEOSCIENCES↗