Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Recrystallization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

The role of annealing and grain boundary controls on the mechanical properties of limestones and marbles

Chemical and mechanical processes are coupled in many geological and geochemical environments. Reactive processes anneal defects and restructure grain boundaries, modifying their elastic properties, levels of internal friction, wave propagation rates and fracture behaviors. The nature of these changes is, however, contingent on the initial state of the rock. Here, in this study, impulse excitation was used to measure changes in mechanical properties as a function of dry and steam heating time at 300 °C for three carbonate rocks: Carrara marble, Carthage marble (Burlington Limestone), and Texas Cream limestone (Edwards limestone), with initial porosities of about 1 %, 3 %, and 27 %, respectively. Frequency-dependent phenomena along with mineral recrystallization were observed. This was coupled with small-angle X-ray and neutron scattering analysis to determine the relationship between changes in bulk mechanical and microstructural properties. An observed decrease in both the Young's and shear moduli in the experimental limestones as a function of heating time reflects and quantifies a reduction in the stiffness of the rock due to annealing. The internal friction of the samples first increases then decreases with reaction time, reflecting defect annealing, but this was balanced against grain boundary dissolution apparently driven by condensation of steam in the confined grain-boundary environment. This suggests an increase in the boiling point under confinement leading to dissolution, increased porosity and widening of the grain boundaries. In addition, comparison of small-angle X-ray and neutron scattering results suggests that it is inappropriate to assume that pores are empty for quantitative analysis of typical small-angle scattering samples.

58 GEOSCIENCES↗

Microstructural Characteristics of DU-xMo Alloys with x = 7-12wt%

Microstructural, phase, and impurity analyses of six depleted uranium-molybdenum alloys were obtained using optical metallography, x-ray diffraction, and carbon/nitrogen/oxygen determination. Uranium-molybdenum alloy foils are currently under investigation for the possible conversion of high-power research reactors to accommodate the use of low-enriched uranium fuel. Understanding basic microstructural behavior of these foils is an important consideration in determining the impact of fabrication processes and in anticipating performance of the foils in a reactor. Average grain diameter decreased with increasing molybdenum content, while the degree of mechanical deformation banding increased with increasing molybdenum content. A lattice parameter, which provided information on stress-corrosion cracking behavior, decreased with increasing molybdenum content, and no significant degree of crystallographic ordering was caused by processing and post-processing conditions employed in this study. Impurity concentration, specifically carbon when it is in solution with the host matrix, inhibited the degree of microstructural recrystallization but did not appear to impact other microstructural traits, such as ?-phase retention or lattice parameter.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Texture evolution and their effects on the mechanical properties of duplex Mg-Li alloy

Texture evolution is strongly dependent on the deformation mode during thermo-mechanical treatments. In this paper, we report the texture evolution in a duplex Mg-Li alloy. The results provide an evidence of deformation mode transition in the hexagonal-close-packed (hcp) alpha phase with various thickness reductions. The activation sequence of deformation modes is basal slip first, and then pyramidal slip during hot-rolling to a thickness reduction of 40%. The relative activity of slip decreases with further thickness reduction. After annealing, basal texture is strengthened and pyramidal component disappears due to static recrystallization and grain growth. The microstructure, specifically texture evolution in both hcp alpha and body-centered cubic (bcc) beta phase and their effects on mechanical properties are quantitatively analyzed and assessed. (C) 2016 Elsevier B.V. All rights reserved.

36 MATERIALS SCIENCE↗

The role of amorphous ZIF in ZIF-8 crystallization kinetics and morphology

Understanding the composition and structure of amorphous precursor phases is fundamental for elucidating two-step crystallization mechanisms and designing shape- and size-controlled nanomaterials. However, that understanding is largely lacking for metal–organic framework compounds despite their growing significance as functional materials. Here, in this study, we report the crystallization of zeolite imidazolate frameworks-8 (ZIF-8, Zn(C 4 H 5 N 2 ) 2 ) via an amorphous ZIF (am-ZIF) solid precursor phase with a rough stoichiometric composition of Zn(C 4 H 5 N 2 ) 1.78 (C 4 H 6 N 2 ) 0.17 (CH 3 COO) 0.22 . The formation of am-ZIF is attributed to the incomplete deprotonation of 2-Methylimidazole (HmIm) and the involvement of the hydrogen bond between CH 3 COO– and –HN, which can further transform into the dense Dia(Zn) structure with a diamondoid crystal topology in pure water. Taking am-ZIF as a precursor, the tunable dissolution and recrystallization kinetics of am-ZIF into ZIF-8, due to the addition of EtOH and CTAB, allows the selective fabrication of dodecahedral, cubic, and hollow ZIF-8. Overall, an in-depth understanding of the differences in composition and structure of am-ZIF from ZIF-8 and the resulting crystallization kinetics suggests a novel approach to designing metal–organic frameworks with controlled crystal morphology.

36 MATERIALS SCIENCE↗

Mechanical joint performances of friction self-piercing riveted carbon fiber reinforced polymer and AZ31B Mg alloy

Carbon fiber reinforced polymer (CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting (F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load (>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads (<1 kN). From fractography, the crack initiation for lower peak load (<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.

36 MATERIALS SCIENCE↗

Cross section TEM characterization of high-energy-Xe-irradiated U-Mo

U-Mo alloys irradiated with 84 MeV Xe ions to various doses were characterized with transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) techniques. The TEM thin foils were prepared perpendicular to the irradiated surface to allow a direct observation of the entire region modified by ions. Furthermore, depth-selective microstructural information was revealed. Varied irradiation-induced phenomena such as gas bubble formation, phase reversal, and recrystallization were observed at different ion penetration depths in U-Mo.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effects of ZrN coating and heat treatment on U-Mo dispersion fuel systems under irradiation

The stability of U-Mo fuel particles embedded in an Al matrix under irradiation can be enhanced through ZrN coatings and/or heat treatment. Here, the present study investigates the irradiation behavior of fuel plates containing U-Mo fuel particles fabricated under various heat-treatment conditions and ZrN coating thicknesses. Different fission densities were also applied to each fuel plate to evaluate the effects of these variables. Results indicate that higher fission densities lead to more grain recrystallization and high burnup structure (HBS) development in the fuel particles. Heat treatment was found to mitigate the accumulation of fission gas bubbles in fuel particles at low fission densities by coarsening their grains. Fuel particles with ZrN coatings of a 1.2 μm thickness or above exhibited reduced formation of U-Mo/Al interaction layers, suggesting the existence of a critical ZrN coating thickness that minimizes the development of these layers. Fission gas bubbles were predominantly observed at grain boundaries of U-Mo fuel particles irradiated at low fission densities. Subgrain boundaries, which appeared to originate from the original grain boundaries containing fission gas bubbles or HBSs, were also observed, indicating the early stage of HBS propagation in the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preferred orientation of phyllosilicates: Comparison of fault gouge, shale and schist

Samples of fault gouge from the San Andreas Fault drill hole (SAFOD), a shale from the North Sea sedimentary basin and schists from metamorphic rocks in the Alps have been analyzed with high energy synchrotron X-rays to determine preferred orientation of mica and clay minerals. The method relies on obtaining 2D diffraction images which are then processed with the crystallographic Rietveld method, implemented in the software MAUD, allowing for deconvolution of phases and extraction of their orientation distributions. It is possible to distinguish between detrital illite/muscovite and authigenic illite/smectite, kaolinite and chlorite, and muscovite and biotite, with strongly overlapping peaks in the diffraction pattern. The results demonstrate that phyllosilicates show large texture variations in various environments, where different mechanisms produce the rock microfabrics: fault gouge fabrics are quite weak and asymmetric with maxima for (001) in the range of 1.5-2.5 multiples of random distribution (m.r.d.). This is attributed to heterogeneous deformation with randomization, as well as dissolution-precipitation reactions. Shale fabrics have maxima ranging from 3 to 9 m.r.d. and this is due to sedimentation and compaction. The strongest fabrics were observed in metamorphic schists (10-14 m.r.d.) and developed by deformation as well as recrystallization in a stress field. In the analyzed samples, fabrics of co-existing quartz are weak. All phyllosilicate textures can be explained by orientation of (001) platelets, with no additional constraints on a-axes.

43 PARTICLE ACCELERATORS↗

Insertion-release of guest species and ionic conduction in polyoxometalate solids with a layer-like Anderson structure

The precipitation of Na{sup +} and K{sup +} mixed salts of Anderson type [SbW{sub 6}O{sub 24}]{sup 7-} by addition of excess of NaNO{sub 3} and NaCl yielded polycrystalline powders of Na{sub 2.5}K{sub 5.3}[SbW{sub 6}O{sub 24}](NO{sub 3}){sub 0.8}.12H{sub 2}O (1) and Na{sub 2}K{sub 5.35}[SbW{sub 6}O{sub 24}]Cl{sub 0.35}.12H{sub 2}O (2), respectively. The two compounds are isomorphous and exhibit a layer-like Anderson (LLA) type structure, which consists of [SbW{sub 6}O{sub 24}]{sup 7-}-containing layers and interstitial Na{sup +}, K{sup +}, NO{sub 3}{sup -} or Cl{sup -}, and water O atoms. Recrystallization of 1 and 2 from hot water yielded Na{sub 2}K{sub 5.4}[SbW{sub 6}O{sub 24}](NO{sub 3}){sub 0.4}.12H{sub 2}O (1-recry) and Na{sub 2}K{sub 5.25}[SbW{sub 6}O{sub 24}]Cl{sub 0.25}.12H{sub 2}O (2-recry) as a result of partial release of NO{sub 3}{sup -} and Cl{sup -} (and Na{sup +} and K{sup +} for charge compensation). Dehydration of 1 and 2 at 400 and 500 {sup o}C (1-dehyd400 and 2-dehyd500) caused a shrinkage of lattice, but their the LLA structures retained. Simulation of X-ray diffraction (XRD) patterns for the dehydrated forms allowed to presume that the each [SbW{sub 6}O{sub 24}]{sup 7-} anion had been 30{sup o}-rotated within its molecular plane in order to avoid intermolecular repulsion. A compressed powder of 1-dehyd400 exhibited fast alkaline-ion conduction with a bulk conductivity of 1.2x10{sup -2} {Omega}{sup -1} cm{sup -1} at 400 {sup o}C. The hosting of a sufficient amount of NO{sub 3}{sup -} together with Na{sup +} for charge compensation into the lattice is crucial for high conduction. -- Graphical abstract: Two compounds Na{sub 2.5}K{sub 5.3}[SbW{sub 6}O{sub 24}](NO{sub 3}){sub 0.8}.12H{sub 2}O (1) and Na{sub 2}K{sub 5.35}[SbW{sub 6}O{sub 24}]Cl{sub 0.35}.12H{sub 2}O (2) possessing a layer-like Anderson (LLA) structure exhibited pseudo intercalation-deintercalation behavior. The dehydrated form of 1 is a high alkaline cation conductor with a conductivity of 1.2x10{sup -2} {Omega}{sup -1} cm{sup -1} at 400 {sup o}C. Display Omitted Research highlights: {yields} Layer-like Anderson-type POM solid accommodates and releases NO{sub 3}{sup -} and Cl{sup -}. {yields} The POM exhibits reversible dehydration by heat treatment. {yields} The dehydration involves rotation of POM molecule retaining layer structure. {yields} The dehydrated POM shows good Na{sup +} and K{sup +} conduction.

36 MATERIALS SCIENCE↗

Composites of Bi{sub 2-x}Sb{sub x}Te{sub 3} nanocrystals and fullerene molecules for thermoelectricity

New nanocomposite thermoelectric material composed from nanocrystallites of Bi-Sb-Te alloys covered by C{sub 60} molecules has been synthesized and studied. An increase of fullerene content leads to the growth of hole concentration in p-type materials and reduction of electron concentration in n-type materials. The fullerene molecules provide additional scattering of phonons reducing lattice heat conductivity. Reduction of heat conductivity exceeds the reduction of electrical conductivity for fullerene content less than 0.5 volume % and essential enhances the thermoelectric figure of merit. The maximum value of thermoelectric figure of merit equals to 1.17 at 450 K was observed in Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} composite containing 0.5 volume % C{sub 60} molecules. The experimental results were analyzed in a frame of the model based on the Boltzmann equation. The analysis considers light and heavy electrons and holes and accounts the intervalley scattering of charge carriers. The calculations of the kinetic coefficients shows that the improvement of the thermoelectric figure of merit originates from the reduction of the lattice heat conductivity caused by fullerene molecules. The dependencies of the thermoelectric figure of merit on the acceptor concentration were calculated. - Graphical abstract: New nanocomposite thermoelectric material composed from nanocrystallites of Bi-Sb-Te alloys covered by C{sub 60} molecules has been synthesized and studied. An increase of fullerene content leads to the growth of hole concentration in p-type materials and reduction of electron concentration in n-type materials. The fullerene molecules provide additional scattering of phonons reducing lattice heat conductivity and enhances the thermoelectric figure of merit. The maximum value of thermoelectric figure of merit equal to 1.17 at 450 K was observed in Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} composite containing 0.5 volume % fullerene molecules. Simulations of thermoelectric properties were made in frame of four bands, 12 valleys Boltzmann equation approach. Simulated and measured temperature dependencies of thermoelectric properties were compared to get unknown model parameters. These parameters were used to calculate dependencies of thermoelectric properties on acceptor concentration. Calculated dependencies of thermoelectric figure of merit on acceptor concentration are presented in the figure for p-type composites with 0 vol.% C{sub 60} (solid lines) and 0.5 vol.% C{sub 60} (dashed lines). Highlights: Black-Right-Pointing-Pointer C{sub 60} doping of Bi-Sb-Te has acceptor effect. Black-Right-Pointing-Pointer Fullerene molecules prevent recrystallization in Bi-Sb-Te nanocomposites. Black-Right-Pointing-Pointer C{sub 60} in Bi-Sb-Te nanocomposites essentially reduces lattice thermal conductivity. Black-Right-Pointing-Pointer Thermoelectric figure of merit in nanocomposite C{sub 60}-Bi-Sb-Te enhanced.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of flower-like Boehmite (γ-AlOOH) via a one-step ionic liquid-assisted hydrothermal route

A simple and novel synthesis process, one-step ionic liquid-assisted hydrothermal synthesis route, has been developed in the work to synthesize Bohemithe (γ-AlOOH) with flower-like structure. The samples were characterized by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FT-IR) and Scanning Electron Microscope (SEM). Ionic liquid [Omim]{sup +}Cl{sup −}, as a template, plays an important role in the morphology and pore structure of the products due to its strong interactions with reaction particles. With the increase in the dosage of ionic liquid [Omim]{sup +}Cl{sup −}, the morphology of the γ-AlOOH was changed from initial bundles of nanosheets (without ionic liquid) into final well-developed monodispersed 3D flower-like architectures ([Omim]{sup +}Cl{sup −}=72 mmol). The pore structure was also altered gradually from initial disordered slit-like pore into final relatively ordered ink-bottle pore. Furthermore, the proposed formation mechanism and other influencing factors such as reaction temperature and urea on formation and morphology of the γ-AlOOH have also been investigated. - Graphical abstract: The flower-like γ-AlOOH architectures composed by nanosheets with narrow size distribution (1.6–2.2 μm) and uniform pore size (6.92 nm) have been synthesized via a one-step ionic liquid-assisted hydrothermal route. - Highlights: • The γ-AlOOH microflowers were synthesized via an ionic liquid-assisted hydrothermal route. • Ionic liquid plays an important role on the morphology and porous structure of the products. • Ionic liquid can be easily removed from the products and reused in recycling experiments. • A “aggregation–recrystallization–Ostwald Ripening“formation mechanism may occur.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrothermal synthesis of single crystals of transition metal vanadates in the glaserite phase

A series of transition metal vanadate crystals were prepared using a high temperature (580 °C) hydrothermal method. The compounds all had the general formula A{sub 2}AEM(VO{sub 4}){sub 2} (A=K, Na, Li; AE=Ba, Sr; M=Co, Fe, Mn). They are all variations of the glaserite structural type and range in symmetry from P-3m1 to P-3 to P2{sub 1}/c. Most of the derivatives contain a planar three-fold rotation operation, making them possible spin frustration candidates. Single crystal structural analyses were performed on many of the derivatives to obtain a detailed understanding of the distortions of the tetrahedral building blocks that accommodate the symmetry distortions. A hydrothermal growth method was developed to grow high quality single crystals of sizes up to 2–3 mm/edge. This method can be generalized for large crystal growth to enable magnetic and neutron diffraction studies that require relatively large single crystals. - Highlights: • The hydrothermal synthesis of glaserite-type vanadates is demonstrated. • Synthesis from stoichiometric component reactions yields 0.2–0.5 mm size crystals. • Hydrothermal recrystallization of glaserite powder yields 2–3 mm size crystals. • The structure varies according to the alkali and alkaline earth metals selected. • Ideal (P-3m1) and distorted (P-3 and P2{sub 1}/c) glaserite structures are observed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Heavy ion irradiation-induced microstructural evolution in pyrochlore Lu{sub 2}Ti{sub 2}O{sub 7} at room temperature and 723 K

Polycrystalline pyrochlore Lu{sub 2}Ti{sub 2}O{sub 7} pellets were irradiated with 600 keV Kr{sup 3+} at room temperature and 723 K to a fluence of 4×10{sup 15} ions/cm{sup 2}, corresponding to an average ballistic damage dose of 10 displacements per atom in the peak damage region. Irradiation-induced microstructural evolution was examined by grazing incidence X-ray diffraction, and cross-sectional transmission electron microscopy. Incomplete amorphization was observed in the sample irradiated at room temperature due to the formation of nano-crystal which has the identical structure of pyrochlore, and the formation of nano-crystal is attributed to the mechanism of epitaxial recrystallization. However, an ordered pyrochlore phase to a swelling disordered fluorite phase transformation is occurred for the Lu{sub 2}Ti{sub 2}O{sub 7} sample irradiated at 723 K, which is due to the disordering of metal cations and anion vacancies. - Graphical Abstract: Polycrystalline pyrochlore Lu{sub 2}Ti{sub 2}O{sub 7} pellets were irradiated with 600 keV Kr{sup 3+} to a fluence of 4×10{sup 15} ions/cm{sup 2} at room temperature and 723 K, Incomplete amorphization was observed in the sample irradiated at room temperature due to the formation of nano-crystal. However, an ordered pyrochlore phase to a swelling disordered fluorite phase transformation is occurred for the Lu{sub 2}Ti{sub 2}O{sub 7} sample irradiated at 723 K, which is due to the disordering of metal cations and anion vacancies. - Highlights: Pyrochlore Lu{sub 2}Ti{sub 2}O{sub 7} pellets were irradiated by heavy ions at RT and 723 K. At RT irradiation, ~75% of amorphization was achieved. The nano-crystals were formed in the damage layer at RT irradiation. The formed nano-crystals enhanced the radiation tolerance of Lu{sub 2}Ti{sub 2}O{sub 7}. A pyrochlore to fluorite phase transformation was observed at 723 K irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The effects of asymmetrical cold rolling on kinetics, grain size and texture in IF steels

Asymmetrical rolling is a promising way to achieve high rolling reductions and potentially grain refinement. However in steels the effect of asymmetrical rolling is not thoroughly quantified. In this paper the impact of cold asymmetrical rolling obtained by changing the roll velocity ratio (from 1.1 to 1.45) on the deformation and recrystallization features has been finely investigated by Electron Back-Scattering Diffraction in a Scanning Electron Microscope. In the investigated conditions (with low thickness reduction), it is found that asymmetrical rolling induces grain refinement and more homogeneous gamma fiber texture.

36 MATERIALS SCIENCE↗

Characterization of adiabatic shear bands in AM60B magnesium alloy under ballistic impact

Adiabatic shear bands in Mg alloy under ballistic impact at a velocity of 0.5 km.s{sup -1} were characterized by means of optical microscope, scanning electron microscope, transmission electron microscope and indenter technique. The results show that adiabatic shear bands were formed around the impacted crater, and the deformed and transformed bands were distinguished by etching colors in metallographic observation. TEM observation shows that the deformed bands were composed of the elongated grains and high density dislocations, while the transformed bands composed of the ultrafine and equiaxed grains were confirmed. In initial stage, the severe localized plastic deformation led to the formation of elongated grains in the deformed bands. With localized strain increasing, the severe localized deformation assisted with the plastic temperature rising led to the severe deformation grains evolved into the ultrafine and equiaxed grains, while the deformed bands were developed into transformed bands. The formation of the ultrafine and equiaxed grains in the transformed bands should be attributed to the twinning-induced rotational dynamic recrystallization mechanism. High microhardness in the bands was obtained because of the strain hardening, grain refining and content concentration. - Research Highlights: {yields} Deformed and transformed bands are found in Mg alloy under ballistic impact. {yields} The microstructures in the deformed and transformed bands are characterized. {yields} The evolution process of the microstructure in the bands is discussed.

36 MATERIALS SCIENCE↗

Microstructural evolution in adiabatic shear bands of copper at high strain rates: Electron backscatter diffraction characterization

The microstructural evolution of adiabatic shear bands in annealed copper with different large strains at high strain rates has been investigated by electron backscatter diffraction. The results show that mechanical twinning can occur with minimal contribution to shear localization under dynamic loading. Elongated ultrafine grains with widths of 100-300 nm are observed during the evolution of the adiabatic shear bands. A rotational dynamic recrystallization mechanism is proposed to explain the formation of the elongated ultrafine grains. - Highlights: Black-Right-Pointing-Pointer The microstructural evolution of ASB is studied by electron backscatter diffraction. Black-Right-Pointing-Pointer Twinning can occur in ASB while the contribution to shear localization is slight. Black-Right-Pointing-Pointer Elongated ultrafine grains are observed during the evolution process of ASB. Black-Right-Pointing-Pointer A possible mechanism is proposed to explain the microstructure evolution of ASB.

36 MATERIALS SCIENCE↗

Microstructure, strengthening mechanisms and hot deformation behavior of an oxide-dispersion strengthened UFG Al6063 alloy

An ultrafine-grained Al6063/Al{sub 2}O{sub 3} (0.8 vol.%, 25 nm) nanocomposite was prepared via powder metallurgy route through reactive mechanical alloying and hot powder extrusion. Scanning electron microcopy, transmission electron microscopy, and back scattered electron diffraction analysis showed that the grain structure of the nanocomposite is trimodal and composed of nano-size grains (< 0.1 {mu}m), ultrafine grains (0.1-1 {mu}m), and micron-size grains (> 1 {mu}m) with random orientations. Evaluation of the mechanical properties of the nanocomposite based on the strengthening-mechanism models revealed that the yield strength of the ultrafine-grained nanocomposite is mainly controlled by the high-angle grain boundaries rather than nanometric alumina particles. Hot deformation behavior of the material at different temperatures and strain rates was studied by compression test and compared to coarse-grained Al6063 alloy. The activation energy of the hot deformation process for the nanocomposite was determined to be 291 kJ mol{sup -1}, which is about 64% higher than that of the coarse-grained alloy. Detailed microstructural analysis revealed that dynamic recrystallization is responsible for the observed deformation softening in the ultrafine-grained nanocomposite. - Highlights: Black-Right-Pointing-Pointer The strengthening mechanisms of Al6063/Al{sub 2}O{sub 3} nanocomposite were evaluated. Black-Right-Pointing-Pointer Hot deformation behavior of the nanocomposite was studied. Black-Right-Pointing-Pointer The hot deformation activation energy was determined using consecutive models. Black-Right-Pointing-Pointer The restoration mechanisms and microstructural changes are presented.

36 MATERIALS SCIENCE↗

EBSD imaging of orientation relationships and variant groupings in different martensitic alloys and Widmanstätten iron meteorites

An automatic method to colorize and quantify the classical Pitsch, Kurdjumov–Sachs, Greninger–Troiano and Nishiyama–Wasserman orientation relationships in the electron backscatter diffraction maps of martensitic/bainitic steels is detailed. Automatic analysis of variant grouping is also presented. The method was applied to low and high carbon steels, and to iron–nickel Widmanstätten meteorites. Many results of recent literature are confirmed. In low carbon steels the individual laths exhibit continuous orientation gradients between the classical orientation relationships, and the laths tend to be grouped by close-packed plane (morphological) packets. A crystallographic scenario describing the formation of the packets is proposed on the base of the one-step model. When the carbon content increases, the orientation spreading is reduced; and martensite tends to form plate groups and burst configurations. In iron–nickel meteorites, the centimeter long Widmanstätten laths do not exhibit continuous orientation gradients but are constituted of subgrains with uniform orientation relationship; the kamacite grains in the plessite regions are grouped into Bain zones, probably due to a recrystallization during the slow cooling of the meteorites. - Highlights: • Analysis of different low and high carbon steels and Widmanstätten meteorites • Automatic color mapping of the classical orientation relationships in EBSD maps • Quantification of variant pairing and grouping tendencies • Crystallographic scenario for the formation of morphological packets.

36 MATERIALS SCIENCE↗