Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Extraction of radium and actinium with dibenzo-21-crown-7 resin and Rose Bengal

The extraction of 224 Ra and 228 Ac with dibenzo-21-crown-7 resin was studied in solutions with Rose Bengal and identical solutions without Rose Bengal (blanks) from pH 3 to 12. Batch studies demonstrated that actinium is extracted at high pH (> 10) from both solutions but with a significantly higher extraction from the Rose Bengal solutions (maximum extraction ~ 60,000) than the blank solutions (maximum extraction ~ 2,000). In the Rose Bengal solutions, there was a weak extraction of actinium at lower pH (4–10) as well. There was no uptake of radium from the blank solutions, and a weak extraction at all pH levels from the Rose Bengal solutions. Kinetics studies were performed for actinium only, as radium had no significant extraction. Two column studies are demonstrated for the separation of radium from actinium. These separations are moderately effective with ~ 78% of the actinium recovered with no detectable radium.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Inorganic resins enable the increased purification efficiency of 82 Sr from rubidium targets for use in PET imaging isotope production

The 82 Sr/ 82 Rb generator system has found use in positron emission tomography (PET) imaging of myocardial perfusion. 82 Sr is produced by proton irradiation of Rb metal/RbCl salt followed by chemical separation. Inorganic ion-exchangers were synthesized by hydrothermal methods and evaluated for the purification of accelerator-produced 82Sr from a RbCl target and co-produced impurities like 75 Se, Fe, Cr, and Ni. A process consisting of removal of bulk RbCl using sodium nonatitanate (SNT), then removal of remaining tracers of Rb and Se using poorly crystalline silicotitanate (pCST) is suitable for 82 Sr separation and achieves higher purity of 82 Sr vs. commonly used organic resins.

43 PARTICLE ACCELERATORS↗

Extraction of selenium and arsenic with TOA-impregnated XAD-2 resin from HCl

Here the uptake of 75 Se and 73 As on trioctylamine-impregnated resin from HCl solutions was studied with batch uptake, kinetics, and column studies. Selenium-75 extracts well (D w ~ 900) at high HCl concentrations (≥ 10 M) with and no extraction of 73 As at any HCl concentration. The uptake kinetics were slow with low extraction (D w < 100) for time periods ≤ 15 min and no clear equilibrium achieved even after 24 h. Column studies were performed to characterize the separation of 75 Se and 73 As; 75Se is retained from conc. HCl while arsenic is eluted with high yields and high radiopurity.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Synergistic extraction of rare earth elements, actinium, americium, and barium with TTA and Pb resin from acetate buffer solutions

The uptake behavior of 88 Y, 140 Ba, 140 La, 141 Ce, 152 Eu, 228 Ac, and 241 Am was studied with batch uptake, kinetics and column studies in a synergistic extraction system with Pb resin and 2-thenoyltrifuoroacetone in acetate-ethanol solutions. The k' values are very high (>10,000) at near neutral pH (~5 to 6) for all of the radioisotopes studied. The kinetics are reasonably fast for column separations, though the uptake rate is dependent on the concentration of 2-thenoyltrifuoroacetone. Column studies were performed to demonstrate the separation of the trivalent actinides and lanthanides from barium and common fssion products ( 99 Mo, 103 Ru).

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Uptake of arsenic and selenium on iron-doped Pb resin

We report the uptake of the radioisotopes 73 As and 75 Se was characterized on Fe 3+ -doped Pb resin (Eichrom Technologies) from pH 1 to 12. There is good uptake of arsenic and selenium over a wide pH range (~ 1 to 10) with a decrease only at high pH (~ 12). Column experiments were performed to demonstrate the separations of these elements from solutions with near neutral pH values (~ 6 to 8) with high yields and high radiopurity. These separations may be relevant for a wide variety of applications especially isotope harvesting research.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Extraction of americium, curium, and californium with LN resin from HCl and HNO 3

The uptake of 241 Am, 244 Cm and 249 Cf with LN resin was studied in HCl and HNO3 solutions with concentrations ranging from 0.02 to 2.5 M. There is high uptake at concentrations < 0.1 M in both acids for all three isotopes with decreasing uptake at higher concentrations and negligible extraction at ≥ 0.6 M. Californium has a higher extraction than americium and curium, which are extremely similar. Kinetics studies showed rapid uptake of all three isotopes. Here, column studies were performed to demonstrate the separation of 241 Am and 249 Cf, and a bulk separation including nine stable lanthanides along with 241 Am, 249 Cf, and 88 Y.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

TALSPEAK-based separation of the trivalent actinides from rare earth elements using LN resin

The separation of 241 Am, 244 Cm and 249 Cf from rare earth elements using LN resin and lactate buffer solutions with diethylenetriaminepentaacetic acid is described with numerous columns studies. The elutions are based on TALSPEAK liquid–liquid extraction chemistry, and provide high yield (> 90%), rapid, simple separations of the trivalent actinides from the lanthanides, which is often challenging due to similarities in chemical behavior among the trivalent f-block elements. Further, all three actinides can be separated from rare earth elements, including from massless fission product samples and samples with small amounts (~ 1–5 mg) of stable lanthanides. Separations with no detectable overlap between the actinide and lanthanide elutions is possible with massless samples, and in samples with mass high separation factors can be achieved (Am/Eu: 171; Am/La: 10 6 ).

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Coating of Steel by Alkyd Resin Reinforced with Al{sub 2}O{sub 3} Nanoparticles to Improve Corrosion Resistance

In this study, an alkyd/Al{sub 2}O{sub 3} nanocomposite coating was prepared and applied on a stainless steel substrate. The Al{sub 2}O{sub 3} nanoparticles (NPs) with different weight ratios (1, 2, and 3 wt.%) were added to the alkyd resin and coated on the substrate via dip-coating technique. Then, the dispersion of NPs in the coating film was investigated using scanning electron microscopy (SEM) and scanning probe microscopy (SPM). The coating thickness estimated by SEM was 20 μm. The corrosion behavior of the coating was examined through the Tafel polarization and salt spray tests. The results showed that the addition of Al{sub 2}O{sub 3} NPs up to 2 wt.% will result in a dense and homogeneous coating which protects the substrate leading to lower corrosion current density from 9.2 × 10{sup −6} to 1.65×10{sup −9} A/cm{sup 2} compared with the uncoated stainless steel.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Oxidation and Ignition Behaviors of Molten Mg-Nd-Zr Alloy in Resin-Sand Mold

High-temperature oxidation behavior of molten Mg-Nd-Zr in the pyrolysis atmosphere of resin-bind sand mold was investigated. The results showed that pouring temperature higher than 1023 K would sharply increase the ignition risk of melt in mold. The oxide formed on Mg-Nd-Zr melt below 973 K consists of two layers: mainly MgO for outer layer; mixture of MgO and Nd{sub 2}O{sub 3} for inner layer. The inner oxide mixture layer played an essential role in the protection of Mg-Nd-Zr matrix. Based on the experimental results and thermodynamic analysis, the oxidation process containing three stages was proposed. Nd- and Zn-enriched zone was found at the subsurface of oxide scale, without the enrichment of Zr. DICTRA calculation results indicated that this phenomenon was caused by the depletion of Mg and up-hill diffusion of Zr. Thus, Zr showed limited protection to the melt in long-term oxidation.

36 MATERIALS SCIENCE↗

Novel alkyd-type coating resins produced using cationic polymerization

Novel, partially bio-based poly(vinyl ether) copolymers derived from soybean oil and cyclohexyl vinyl ether (CHVE) were produced by cationic polymerization and investigated for application as alkyd-type surface coatings. Compared to conventional alkyd resins, which are produced by high temperature melt condensation polymerization, the poly(v9nyl ether)s provide several advantages. These advantages include milder, more energy efficient polymer synthesis, elimination of issues associated with gelation during polymer synthesis, production of polymers with well-defined composition and relatively narrow molecular weight distribution, and elimination of film formation and physical property issues associated with entrained monomers, dimers, trimers, etc. The results of the studied showed that the thermal, mechanical, and physical properties of the coatings produced from these novel polymers varied considerably as a function of polymer composition and cure temperature. Overall, the results suggest a good potential for these novel copolymers to be used for coatings cured by autoxidation.

99 GENERAL AND MISCELLANEOUS↗

Separation of cobalt, nickel, and manganese in leach solutions of waste lithium-ion batteries using Dowex M4195 ion exchange resin

Current methods to separate and recover critical metals from waste lithium-ion battery (LIB) scrap require multiple unit operations that involve selective leaching and a combination of separation methods. These methods include impurity removal, solvent extraction, ion exchange, and precipitation, to achieve high purity Co and Ni products. In this paper an efficient extraction strategy was developed to individually separate Ni and Co from a LIB leachate that was generated from an electrochemical leaching process. By using Dowex M4195 resin, as the only method of separation, additional impurity removal operations were not needed. After loading and eluting, three different fractions were obtained: 99.0% Ni concentrate, 98.5% Co concentrate, and a Li/Mn rich concentrate allowing the separation of Ni, Co and Mn. Here, the developed process is then presented as an alternative for metal recovery from leachates from scrap LIBs with minimum chemical addition and pH adjustment.

36 MATERIALS SCIENCE↗

Accumulation mechanisms for contaminants on weak-base hybrid ion exchange resins

Mechanism of hexavalent chromium removal (Cr(VI) as CrO 4 2- ) by the weak-base ion exchange (IX) resin ResinTech® SIR-700-HP (SIR-700) from simulated groundwater is assessed in the presence of radioactive contaminants iodine-129 (as IO 3 - ), uranium (U as uranyl UO 2 2+ ), and technetium-99 (as TcO 4 - ), and common environmental anions sulfate (SO 4 2- ) and chloride (Cl-). Batch tests using the acid sulfate form of SIR-700 demonstrated Cr(VI) and U(VI) removal exceeded 97%, except in the presence of high SO 4 2- concentrations (536 mg/L) where Cr(VI) and U(VI) removal decreased to ≥ 80%. However, Cr(VI) removal notably improved with co-mingled U(VI) that complexes with SO 4 2- at the protonated amine sites. These U–SO 4 2- complexes are integral to U(VI) removal, as confirmed by the decrease in U(VI) removal (<40%) when the acid chloride form of SIR-700 was used instead. Solid phase characterization revealed that CrO 4 2- is removed by IX with SO 4 2- complexes and/or reduced to amorphous Cr(III)(OH) 3 at secondary alcohol sites. Tc(VII)O 4 - and I(V)O 3 - also undergo chemical reduction, following a similar removal mechanism. Oxyanion removal preference is determined by the anion reduction potential (CrO 4 2 - >TcO 4 - >IO 3 - ), geometry, and charge density. For these reasons, 39% and 69% of TcO 4 - and 17% and 39% of IO 3 - are removed in the presence and absence of Cr(VI), respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Resin chemistry and particle size influence on stereolithography with silicon carbide

Stereolithography (SLA) is an established process able to produce high resolution polymer parts with complex geometries. Silicon carbide (SiC) has uses in a variety of applications, but traditionally was difficult to manufacture into complex geometries. There have been advances in producing SiC through SLA using a SiC-derived ceramic such as silicon oxycarbide (SiOC). In this study, a slurry using a commercially available resin as the base material with additional modifiers was investigated to create a SiC slurry ready for pressureless sintering. The effects of photoinitiator, dispersant and a bimodal distribution of SiC particle sizes was studied using a design of experiments (DOE). A slurry with a bimodal distribution of 70 % coarse and 30 % fine SiC powder at 40 % solids loading by volume was prepared and successfully printed. Rheology measurements show the slurry to have viscoelastic shear thinning behavior below the recommended 1000 Pas necessary for printing. Printing parameters for the new material on a commercially available SLA printer were studied parametrically. The laser marking speeds found to print the slurry was 260 mm/s and 130 mm/s. A slurry and printing parameters were determined to produce a green part with a proposed debinding cycle.

Herd, Tien [ORNL]↗

Antibacterial dental adhesive resins containing nitrogen-doped titanium dioxide nanoparticles

The development of dental adhesive resins with long-lasting antibacterial properties is a possible solution to overcome the problem of secondary caries in modern adhesive dentistry.Objectives: (i) Synthesis and characterization of nitrogen-doped titanium dioxide nanoparticles (N_TiO 2 ), (ii) topographical, compositional and wettability characterization of thin-films (unaltered and experimental) and, (iii) antibacterial efficacy of N_TiO 2 -containing dental adhesives against Streptococcus mutans biofilms.Materials and methods: Nanoparticles were synthesized and characterized using different techniques. Specimens (diameter = 12 mm, thickness ≅ 15 μm) of OptiBond Solo Plus (Kerr Corp., USA) and experimental adhesives [50, 67 and 80% (v/v)] were fabricated, photopolymerized (1000 mW/cm 2 , 1 min) and UV-sterilized (254 nm, 800,000 μJ/cm 2 ) for microscopy, spectroscopy, wettability and antibacterial testing. Wettability was assessed with a contact angle goniometer by dispensing water droplets (2 μL) onto four random locations of each specimen (16 drops/group). Drop profiles were recorded (1 min, 25 frames/s, 37 °C) and contact angles were calculated at time = 0 s (θ INITIAL ) and time = 59 s (θ FINAL ). Antibacterial testing was performed by growing S. mutans (UA159-ldh, JM10) biofilms for either 3 or 24 h (anaerobic conditions, 37 °C) with or without continuous light irradiation (410 ± 10 nm, 3 h = 38.75 J/cm 2 , 24 h = 310.07 J/cm 2 ) against the surfaces of sterile specimens.Results: N_TiO 2 was successfully prepared using solvothermal methods. Doped-nanoparticles displayed higher light absorption levels when compared to undoped titania. Experimental adhesives demonstrated superior antibacterial efficacy in dark conditions.Conclusions: The findings presented herein suggest that N_TiO 2 is a feasible antibacterial agent against cariogenic biofilms.

36 MATERIALS SCIENCE↗

Pixelated plastic scintillator array manufacturing using fast-, photo-curable resin

Pixelated plastic scintillator arrays can serve as high efficiency and high resolution neutron imaging detectors. Manufacturing these arrays is intensive in both time and labor. This article presents a fabrication method based on additive manufacturing for two-dimensional plastic organic scintillator arrays using a custom-built automated assembly machine and a custom photocurable resin that has significant non-aromatic acrylate oligomer content. The process involves two main stages: fully autonomous production of one-dimensional layered arrays, followed by semi-autonomous cutting and stacking to form two-dimensional pixel arrays. One-dimensional arrays were manufactured at a rate of around 4 layers per hour with minimal defects and tight dimensional tolerances, while two-dimensional arrays up to 7 x 7 pixels and 70 mm in length were completed in approximately 3.5 hours. Final arrays exhibited dimensional deviations of less than 0.5 mm. Two-dimensional arrays read out by a multi-anode photomultiplier tube demonstrated per-pixel position resolution and pulse-shape discrimination, enabling gamma–neutron interaction separation in mixed radiation environments.

36 MATERIALS SCIENCE↗

CO 2 Sorption in Moisture Swing Anion Exchange Resins for Direct Air Capture: Experimental Isotherm Determination and Modeling

Moisture swing (MS) sorption is a promising direct air capture (DAC) technology to achieve negative CO 2 emissions and counter global warming. Here, in this study, MS CO 2 sorption in a model MS sorbent, IRA900, was investigated. IRA900 is a macroporous commercial strong-base anion exchange resin (AER) with quaternary ammonium functional groups. A rigorous CO 2 desorption process was developed to desorb all CO 2 from the sample and obtain CO 2 sorption isotherms as a function of relative humidity, CO 2 partial pressure, and temperature. CO 2 sorption increased with decreasing relative humidity, decreasing temperature, and increasing CO 2 partial pressure. Remarkably, the total CO 2 uptake from the sorption isotherms matched the ion exchange capacity (IEC) of the material, suggesting a stoichiometry of one CO 2 molecule reacting per active site. An isotherm model for CO 2 sorption starting with empty sorption sites (i.e., with the AER in the OH – form) described the experimental data well, supporting the hypothesis that the bicarbonate-loaded AER fully unloaded to the OH – state following rigorous CO 2 desorption. CO 2 sorption kinetics were studied, and carbon diffusion coefficients were estimated as a function of %RH and CO 2 partial pressure. Overall, this study provides a roadmap for the systematic evaluation of MS CO 2 DAC materials.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Adsorption Equilibrium, Kinetics, and Column Breakthrough Data of Acetic Acid, Butyric Acid, and Lactic Acid on IRN-78 Ion-exchange Resin at Initial pH ~3 – 7 and Temperature 25 – 55 °C

This work presents systematic aqueous-phase adsorption equilibrium, kinetics, and column breakthrough measurements with three key biointermediates that are common compounds in many bioprocesses. Adsorption equilibrium experiments were carried out with acetic acid, butyric acid, and lactic acid on a commercial ion-exchange resin, Amberlite IRN-78, at wide ranges of acid concentration (8-500 mmol/L), initial pH (similar to 3-7), and temperature (25-55 degrees C), simulating the effluent characteristics from different fermenter operations. The kinetics and column breakthrough experiments were conducted at an initial pH of 6 and a concentration of 200 mmol/L. The equilibrium study shows a higher loading at the initial pH < pK(a) and a lower loading at the initial pH > pK(a). Overall removal varies between 16 and 99% depending on the initial pH, temperature, and organic acid concentration and type. The study further indicates monolayer adsorption at the equilibrium pH > 10 and multilayer adsorption at the equilibrium pH < 6. The thermodynamic modeling of adsorption isotherm data was carried out using Langmuir and Freundlich isotherms. IRN-78 presents fast adsorption kinetics as the maximum loading was attained in <= 10 min and nearly the same breakthrough time for all three organic acids involved in this study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Adsorption Equilibrium, Kinetics, and Column Breakthrough Data for Aqueous Solutions of Binary-Acid and Ternary-Acid Mixtures of Acetic Acid, Butyric Acid, and Lactic Acid on IRN-78 Ion-Exchange Resin at Initial pH Levels of ∼3–7 and at 25–55 °C

This work is part of an effort to develop thermophysical property data and models supporting adsorptive process development for organic acid separation from a dilute aqueous solution of fermentation broth. It presents systematic experimental measurements for aqueous-phase adsorption equilibrium, kinetics, and column breakthrough for three binary-acid aqueous mixtures (acetic acid + lactic acid, butyric acid + lactic acid, and acetic acid + butyric acid) and one ternary-acid aqueous mixture (acetic acid + butyric acid + lactic acid) on Amberlite IRN-78 ion-exchange resin. The equilibrium measurements covered broad ranges of the initial acid concentration (100–400 mmol/L), initial pH (∼3–7), and temperature (25–55 °C). The equilibrium data for the binary-acid and ternary-acid aqueous mixtures indicate selective adsorption of lactic acid at initial pH levels of ∼3 and 4, while acetic acid and butyric acid are selectively adsorbed at initial pH levels of 5, 6, and 7. The subsequent kinetics and column breakthrough experiments were performed at 200 mmol/L with equimolar ratios, an initial pH of 6, and 25 °C. In conclusion, the measurements provide essential data sets for rigorous thermodynamic modeling and process simulation of adsorptive separation processes for organic acid separation from fermentation broth.

Adsorption↗