Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESIDUAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An innovative digital image correlation technique for in-situ process monitoring of composite structures in large scale additive manufacturing

As additive manufacturing (AM) continues to develop and become a standardized manufacturing method, there will be a continued need to provide in-situ monitoring during the manufacturing of polymer composite printed components. Thermal residual stress is a primary cause of failures such as interlayer disbonds or delamination, micro cracking, and dimensional instability, which can occur during or after the build. Here, we report a novel digital image correlation (DIC) adaptation to monitor thermal residual stresses during the entire print process for large-scale AM. In this work, DIC has been investigated (a) by the natural speckle produced by the polymer surface for correlation, (b) to monitor AM build, and (c) to evaluate the effect of thermal residual stress on warpage of the printed component. The natural speckle pattern of the AM material resulted in a respectable 3.57% error compared to the traditional painted speckle pattern of 3.05% error. DIC measured a 190% increase in vertical displacement at the edge of the wall compared to the center, indicating warpage during AM. This work is a step towards a non-intrusive residual stress measuring technique using DIC for large-scale AM.

36 MATERIALS SCIENCE↗
DOE OSTI2014

IR Heat Treatment of Hybrid Steel-Al Joints

The technical objective of this CRADA is to develop and model a heat treatment process based on Infra- Red (IR) heating of a overcast Al/steel bimetallic joint to produce a T5 temper in a shorter period of time than is currently achievable and, separately, to produce a modified T6 temper for improved mechanical properties without the loss of joint integrity. IR heat treatments have been demonstrated to provide reduced processing time, reduced energy requirements, and improved material properties of Al components, including strength and elongation, relative to convective thermal heat treatment methods. A prototype IR furnace was assembled to heat treat these joints. The residual stress state of the joints were modeled in the as-cast condition, as well as the T5 and T6 condition. Neutrons were used to measure the residual stresses in the joints for various heat treatments. ORNL is uniquely equipped to partner with Vehma in the experimental evaluation and modeling of Al/steel bi-metallic joints. ORNL possesses a long history of microstructural, crystallographic and mechanical characterization of structural materials. Unique facilities at ORNL for this work include the NRSF2/HB-2B beamline at the High Flux Isotope Reactor (HFIR) for residual stress measurements with neutron diffraction, metallurgical expertise for heat treating and modeling capability of the manufacturing of these joints for residual stress prediction. All of these capabilities were utilized in this CRADA. The CRADA began in April 2011 and ended in September 2014 (41 months).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2014

Analysis of surface integrity of grinded gears using Barkhausen noise analysis and x-ray diffraction

The contribution is focused to present results of study grinded gears made of 18CrNiMo7-6 steel used in the wind power plant for support (service) purposes. These gears were case-hardened due to standard hard case and soft core formation. This heat treatment increases wear resistance and fatigue strength of machine parts. During serial production some troubles with surface integrity have occurred. When solving complex problems lots of samples were prepared. For grinding of gears were used different parameters of cutting speed, number of material removal and lots from different subsuppliers. Material characterization was carried out using Barkhausen noise analysis (BNA) device; X-ray diffraction (XRD) measurement of surface residual stresses was done as well. Depth profile of measured characteristics, e.g. magnetoelastic parameter and residual stress was obtained by step by step layers' removing using electrolytic etching. BNA software Viewscan was used to measure magnetizing frequency sweep (MFS) and magnetizing voltage sweep (MVS). Scanning of Magnetoelastic parameter (MP) endwise individual teeth were also carried out with Viewscan. These measurements were done to find problematic surface areas after grinding such as thermal damaged locations. Plots of the hardness and thickness of case-hardened layer on cross sections were measurered as well. Evaluation of structure of subsurface case-hardened layer and core was made on etched metallographic patterns. The aim of performed measurements was to find correlation between conditions of grinding, residual stresses and structural and magnetoelastic parameters. Based on correlation of measured values and technological parameters optimizing the production of gears will be done.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1990

Use of unbalanced laminates as a screening method for microcracking

State-of-the-art, high temperature polyimide matrix composites, reinforced with continuous graphite fibers are known to be susceptible to intraply cracking when thermally cycled over their useful service temperature range. It is believed that the transply cracking, in part, results from residual stresses caused by differences in coefficients of thermal expansion (CTE) between the polymer matrix and the reinforcement. Thermal cycling tests to investigate this phenomenon involve expensive time and energy consuming programs which are not economically feasible for use as a part of a materials screening process. As an alternative to thermal cycling studies, a study of unbalanced crossply graphite fiber reinforcement composites was conducted to assess the effect of the composite ply layup and surface condition on the residual stresses that remain after the processing of these materials. The residual stresses were assessed by measuring the radii of curvature of the types of laminates that were studied. The temperature at which stress-free conditions existed were determined and a dye penetrant method was used to observe surface damage resulting from excessive residual stress buildup. These results are compared with some published results of thermal cycling tests that were previously conducted on balanced polyimide composites.

Papadopoulos, Demetrios S.↗
NASA NTRS1990

Use of unbalanced laminates as a screening method for microcracking

State-of-the-art, high temperature polyimide matrix composites, reinforced with continuous graphite fibers are known to be susceptible to intraply cracking when thermally cycled over their useful service temperature range. It is believed that the transply cracking, in part, results from residual stresses caused by differences in coefficients of thermal expansion (CTE) between the polymer matrix and the reinforcement. Thermal cycling tests to investigate this phenomenon involve expensive time and energy consuming programs which are not economically feasible for use as a part of a materials screening process. As an alternative to thermal cycling studies, a study of unbalanced crossply graphite fiber reinforcement composites was conducted to assess the effect of the composite ply layup and surface condition on the residual stresses that remain after the processing of these materials. The residual stresses were assessed by measuring the radii of curvature of the types of laminates that were studied. The temperature at which stress-free conditions existed were determined and a dye penetrant method was used to observe surface damage resulting from excessive residual stress buildup. These results are compared with some published results of thermal cycling tests that were previously conducted on balanced polyimide composites.

Papadopoulos, Demetrios S.↗
DOE OSTI2019

Stress and Fracture of Crystalline Silicon Cells in Solar Photovoltaic Modules – A Synchrotron X-ray Microdiffraction based Investigation

Fracture of crystalline silicon (c-Si) solar cells in photovoltaic modules is a big concern to the photovoltaics (PV) industry. Cell cracks cause performance degradation and warranty issues to the manufacturers. The roots of cell fractures lie in the manufacturing and integration process of the cells and modules as they go through a series of elevated temperature and pressure processes, involving bonding of dissimilar materials, causing residual stresses. Evaluation of the exact physical mechanisms leading to these thermomechanical stresses is highly essential to quantify them and optimize the PV modules to address them. Here we present a novel synchrotron X-ray microdiffraction based techniques to characterize the stress and fracture in the crystalline silicon PV modules. We show the detailed stress state after soldering and lamination process, using the synchrotron X-ray microdiffraction experiments. We also calculate the maximum tolerable microcrack size in the c-Si cells to sustain the residual stress after lamination. We further demonstrate the effect of these residual stresses on the cell fractures using the widely accepted fracture (4-point bending) tests. These test results show that the soldering and lamination induced localized residual stresses indeed reduce the load-carrying capacity of the c-Si cells.

14 SOLAR ENERGY↗
DOE OSTI2019

Microstructure and Properties of Inconel 718 Fabricated by Directed Energy Deposition with In-Situ Ultrasonic Impact Peening

Many inherent issues, such as the detrimental residual stress, columnar grains with anisotropy, and weak mechanical properties, have severely impeded the adoption of metal additive manufacturing (AM) techniques including powder bed fusion and directed energy deposition (DED) processes. In this study, a hybrid AM process that consists of layer-wise laser metal deposition (i.e., a DED process) and in-situ ultrasonic impact peening (UIP) was applied to obtain Inconel 718 superalloy workpieces. Also, for further property enhancement, a post-heat treatment was applied to the deposited material obtained by the hybrid AM process. Scanning electron microscopy and transmission electron microscope were used to investigate the microstructure morphology and reveal the underlying strengthening mechanism. Electron backscatter diffraction was employed to quantitatively study the microstructure resulted from the hybrid AM process and the post-heat treatment. The profile of residual stress along the depth direction was obtained through X-ray diffraction. The results demonstrate that this hybrid AM process is capable of producing high-quality metal parts with significantly refined microstructure, and beneficial compressive residual stress along the depth into surface. Severe plastic strains are introduced by UIP, and the resulted mechanical twinning and dynamic recrystallization play an important role in refining microstructure. The material microstructure is further refined down to 100 µm, and the texture anisotropy is significantly diminished after solution treatment at 980 °C for 1 hour. Under the as-built condition, in-situ ultrasonic peening alters the residual stress component from a tensile state to an overall compressive state with a maximum value of − 190 MPa within the range of measurement depth.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Corrosion Behavior of Aqua-Blasted and Laser-Engraved Type 316L Stainless Steel

The effect of aqua blasting and laser engraving on surface microstructure development, residual stress and corrosion resistance of type 316L stainless steel has been investigated. Aqua blasting resulted in a deformed near-surface microstructure containing compressive residual stresses. Subsequent laser engraving produced a surface layer with tensile residual stresses reaching to a depth of 200 microns. Changes of surface roughness topography were accompanied by the development of a thick oxide/hydroxide film after laser engraving. The atmospheric corrosion behavior of all surfaces with MgCl{sub 2}-laden droplets was compared to their electrochemical response in 1M NaCl and 0.7 M HCl aqueous solutions. The measured total volume loss after atmospheric corrosion testing was similar for all investigated surface conditions. Laser-engraved surface exhibited the smallest number of corrosion sites, but the largest mean corrosion depth.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Analysis of critically refracted longitudinal waves

Fabrication processes, such as, welding, forging, and rolling can induce residual stresses in metals that will impact product performance and phenomena such as cracking and corrosion. To better manage residual stress tools are needed to map their distribution. The critically refracted ultrasonic longitudinal (LCR) wave is one such approach that has been used for residual stress characterization. It has been shown to be sensitive to stress and less sensitive to the effects of the texture of the material. Although the LCR wave is increasingly widely applied, the factors that influence the formation of the LCR beam are seldom discussed. This paper reports a numerical model used to investigate the transducers' parameters that can contribute to the directionality of the LCR wave and hence enable performance optimization when used for industrial applications. An orthogonal test method is used to study the transducer parameters which influence the LCR wave beams. This method provides a design tool that can be used to study and optimize multiple parameter experiments and it can identify which parameter or parameters are of most significance. The simulation of the sound field in a 2-D 'water-steel' model is obtained using a Spatial Fourier Analysis method. The effects of incident angle, standoff, the aperture and the center frequency of the transducer were studied. Results show that the aperture of the transducer, the center frequency and the incident angle are the most important factors in controlling the directivity of the resulting LCR wave fields.

42 ENGINEERING↗
DOE OSTI2018

Method for controlling stress gradients in PVD aluminum nitride

In this study we describe a method for controlling both the residual stress and the through-thickness stress gradient of aluminum nitride (AlN) thin films using a multi-step deposition process that varies the applied radio frequency (RF) substrate bias. The relationship between the applied RF substrate bias and the AlN residual stress is characterized using AlN films grown on oxidized silicon substrates is determined using 100 nm–1.5 μm thick blanket AlN films that are deposited with 60–100 W applied RF biases; the stress-bias relationship is found to be well described using a power law relationship. Using this relationship, we develop a model for varying the RF bias in a series of discrete deposition steps such that each deposition step has zero average stress. The applied RF bias power in these steps is tailored to produce AlN films that have minimized both the residual stress and the film stress gradient. AlN cantilevers were patterned from films deposited using this technique, which show reduced curvature compared to those deposited using a single RF bias setting, indicating a reduction of the stress gradient in the films.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Development of a plasma sprayed ceramic gas path seal for high pressure turbine applications

The plasma sprayed graded layered yittria stabilized zirconia (ZrO2)/metal(CoCrAlY) seal system for gas turbine blade tip applications up to 1589 K (2400 F) seal temperatures was studied. Abradability, erosion, and thermal fatigue characteristics of the graded layered system were evaluated by rig tests. Satisfactory abradability and erosion resistance was demonstrated. Encouraging thermal fatigue tolerance was shown. Initial properties for the plasma sprayed materials in the graded, layered seal system was obtained, and thermal stress analyses were performed. Sprayed residual stresses were determined. Thermal stability of the sprayed layer materials was evaluated at estimated maximum operating temperatures in each layer. Anisotropic behavior in the layer thickness direction was demonstrated by all layers. Residual stresses and thermal stability effects were not included in the analyses. Analytical results correlated reasonably well with results of the thermal fatigue tests. Analytical application of the seal system to a typical gas turbine engine application predicted performance similar to rig specimen thermal fatigue performance. A model for predicting crack propagation in the sprayed ZrO2/CoCrAlY seal system was proposed, and recommendations for improving thermal fatigue resistance were made. Seal system layer thicknesses were analytically optimized to minimize thermal stresses in the abradability specimen during thermal fatigue testing. Rig tests on the optimized seal configuration demonstrated some improvement in thermal fatigue characteristics.

Shiembob, L. T.↗
NASA NTRS1990

Micromechanical thermal analysis of interphase region in a titanium aluminide MMC

The high reactivity between the fiber and matrix in silicon carbide/titanium aluminide MMCs leads to the formation of brittle reaction products at the fiber/matrix (F/M) interface. Also, the high thermal expansion coefficient mismatch between the fiber and matrix leads to high tensile residual stresses at the F/M interface, and this can lead to premature cracking during cooldown. One solution to these problems is the use of a metallic fiber coating like Ta which acts as an F/M diffusion barrier and reacts with the matrix to form a beta stabilized compliant layer. A finite element micromechanics analysis was performed to study the effects of Ta and beta interphase layers on the thermal residual stresses during consolidation. A 5-micron-thick beta layer reduced cool-down stresses by 8 percent compared to a 2 percent reduction computed for a Ta layer of the same thickness. Plastic yielding in the Ta was not effective in reducing cool-down stresses. Compliant alpha-2 particles next to the stiffer gamma particles reduced stresses in the gamma particles by less than 2 percent. A simple closed form analysis was developed to calculate thermal residual stresses in a fiber/interphase/matrix system. A 2-micron-thick Ag interphase layer was found to reduce residual stresses by about 11 percent.

Naik, R. A.↗
NASA NTRS1981

Effects of environmental variables on the crack initiation stages of corrosion fatigue of high strength aluminum alloys

Fatigue initiation in six aluminum alloys used in the aircraft industry was investigated. Cyclic loading superimposed on a constant stress was alternated with atmospheric corrosion. Tests made at different stress levels revealed that a residual stress as low as 39% of the yield strength caused stress corrosion cracking in some of the alloys. An atmospheric corrosion rate meter developed to measure the corrosivity of the atmosphere is described. An easily duplicated hole in the square test specimen with a self-induced residual stress was developed.

Poteat, L. E.↗
NASA NTRS1998

Electroformed Nickel Mirrors for the Next Generation Space Telescope

This paper summarizes the work to date on a novel mirror fabrication technique being developed at the Marshall Space Flight Center for potential use on the Next Generation Space Telescope (NGST). This technique involves forming an extremely lightweight mirror by electroplating nickel and nickel based alloys onto a highly polished precision mandrel. The resulting mirror shell can then be backed up with or attached to a lightweight structure to produce a mirror element that is on the order of 15 kg/sq m areal density. Since the mirrors are fabricated from a mandrel (or master), subsequent mirrors can be made with very high economy; this technique is particularly suited to segmented mirrors schemes whereby large apertures are achieved through the deployment of smaller segments. Control of the electroplating process is the key element for producing high quality optics; bath chemistry and real time control of the plating current density yields uniform grained electroforms with zero residual stress. To accomplish this, a special electronic sensor was developed whereby the residual stress can be monitored as the nickel is electrolytically deposited. This information is used in a feedback loop to modulate current density which, in turn, directly governs the residual stress. Details pertaining to this and other aspects of the fabrication of a half meter mirror will be published along with test results and metrology data.

Redmon, John W.↗
DOE OSTI2019

Edge turbulence evolution and intermittency development near the density limit on the HL-2A tokamak

The development of intermittent non-Gaussian processes is researched in the edge turbulence of ohmically heated HL-2A discharges approaching the density limit. As the density limit is approached, the E × B shear flow at the last closed flux surface (LCFS) weakens, a strong positive skewness develops in the scrape-off layer (SOL), and negative skewness develops inside the LCFS of turbulent density fluctuations. A conditional averaging analysis confirms more frequent increased amplitude positive (negative) going density fluctuation activity in the SOL (inside the LCFS) as the density limit is approached. The measured turbulent stress across the edge, LCFS, and SOL region is decomposed into diffusive and residual stress components, and the nonlinear exchange of kinetic energy between the turbulence and the low-frequency E × B shear flow is determined. Residual stress acts to amplify the E × B flow at the LCFS, while the diffusive stress acts to dissipate the flow just inside this region, at the interface between the core plasma and the LCFS. The relative strength of the flow drive associated with the residual stress weakens as the density limit is approached, while the turbulent viscosity associated with the diffusive stress increases at high density. The adiabatic parameter, k z 2 v th 2 / ω ν e , drops significantly to about 0.5 in the SOL when the density limit is approached, indicating a transition from the adiabatic regime to the hydrodynamic regime due to increased collisionality. Such changes enhance the particle transport through the nonadiabatic electron response and hence should end in a stronger edge cooling at fixed edge plasma heat flux.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Effect of Internal Structure on Warpage in a Large-Scale Additive Manufacturing Process With Bio-Derived Composites

Extrusion-based large-format additive manufacturing (LFAM) often results in unintended deformation and failures due to thermal residual stress between layers. This LFAM involves a hot molten polymer deposited on a previously deposited and cooled layer, generating a temperature mismatch between the layers. The temperature discrepancy causes a thermal contraction mismatch, generating thermal residual stress. Due to the residual stress, printed structures experience warpage and delamination Therefore, understanding the heat distribution behavior is essential to preventing undesired deformation and failures. The goal of this study is to investigate the effect of infill patterns on heat distribution and deformation in an LFAM system. Wood fiber-reinforced polylactic acid was used as a sustainable and low-cost reinforcement material. A numerical model was developed to predict the temperature and deformation field with thermo-mechanical properties, which were measured by a dynamic mechanical analysis and a thermal expansion test. Simulations were performed on a box geometry with three different infill patterns. The simulation model was verified with temperature data gathered from an infrared camera. The results show good agreement between predicted and measured temperature profiles. The developed simulation model was applied to a roof tray with different infill patterns for a case study. We found that the different thermal mass distributions resulting from the various infill patterns affected the heat distribution and deformation. These findings contribute to a better understanding of the thermal and mechanical behavior of LFAM.

Jo, Eonyeon↗
DOE OSTI2019

Main-ion intrinsic toroidal rotation across the ITG/TEM boundary in DIII-D discharges during ohmic and electron cyclotron heating

Direct measurements of deuterium main-ion toroidal rotation spanning the linear ohmic to saturated ohmic confinement (LOC-SOC) regime and with additional electron cyclotron heating (ECH) are proposed and compared with the more commonly measured impurity (carbon) ion rotation in DIII-D. Main ions carry the bulk of the plasma toroidal momentum, and hence, the shape of the main-ion rotation is more relevant to the study of angular momentum transport in tokamaks. Both in the LOC regime and with ECH, the main-ion toroidal rotation frequency is flat across the profile from the sawtooth region to the plasma separatrix. However, the impurity rotation profile possesses a rotation gradient, with the rotation frequency being lower near the plasma edge, implying a momentum pinch or negative residual stress inferred from the impurity rotation that differs from the main-ion rotation. In the SOC regime, both the main-ion and impurity rotation profiles develop a deeply hollow feature near the midradius while maintaining the offset in the edge rotation, both implying a positive core residual stress. In the radial region where the rotation gradient changes most dramatically, turbulence measurements show that density fluctuations near the trapped electron mode (TEM) scale are higher when the rotation profile is flat and drop significantly when the plasma density is raised and the rotation profile hollows, consistent with instabilities damped by collisions. Linear initial value gyrokinetic simulations with GYRO indicate that the transition from LOC-SOC in DIII-D occurs as TEMs are replaced by ion temperature gradient (ITG) driven modes from the outer radii inwards as the plasma collisionality increases, Z eff decreases, and the power flow through the ion channel progressively increases due to the electron-ion energy exchange. Gyrofluid modeling with trap gyro-Landau fluid (TGLF) successfully reproduces the plasma profiles at key times in the discharge and in time dependent simulations with predictive TRANSP. TGLF indicates that in the LOC and SOC regimes as well as with ECH, subdominant modes are present and that the plasma is not in a pure TEM or ITG binary state, but rather a more subtle mixed state. Predictions of the main-ion rotation profiles are observed with global nonlinear gyrokinetic simulations using GTS and reveal that the flat rotation is due to oscillatory variation of the turbulent residual stress across the profile, whereas the deeply hollow rotation profile is due to a larger-scale, dipole-like stress profile. In these cases, the predicted and observed main-ion rotation profile is consistent with the balance of turbulent residual stress and momentum diffusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2017

Metal Big Area Additive Manufacturing: Process Modeling and Validation

Metal Big Area Additive Manufacturing (mBAAM) is a new additive manufacturing (AM) technology for printing large-scale 3D objects. mBAAM is based on the gas metal arc welding process and uses a continuous feed of welding wire to manufacture an object. An electric arc forms between the wire and the substrate, which melts the wire and deposits a bead of molten metal along the predetermined path. In general, the welding process parameters and local conditions determine the shape of the deposited bead. The sequence of the bead deposition and the corresponding thermal history of the manufactured object determine the long range effects, such as thermal-induced distortions and residual stresses. Therefore, the resulting performance or final properties of the manufactured object are dependent on its geometry and the deposition path, in addition to depending on the basic welding process parameters. Physical testing is critical for gaining the necessary knowledge for quality prints, but traversing the process parameter space in order to develop an optimized build strategy for each new design is impractical by pure experimental means. Computational modeling and optimization may accelerate development of a build process strategy and saves time and resources. Because computational modeling provides these opportunities, we have developed a physics-based Finite Element Method (FEM) simulation framework and numerical models to support the mBAAM process s development and design. In this paper, we performed a sequentially coupled heat transfer and stress analysis for predicting the final deformation of a small rectangular structure printed using the mild steel welding wire. Using the new simulation technologies, material was progressively added into the FEM simulation as the arc weld traversed the build path. In the sequentially coupled heat transfer and stress analysis, the heat transfer was performed to calculate the temperature evolution, which was used in a stress analysis to evaluate the residual stresses and distortions. In this formulation, we assume that physics is directionally coupled, i.e. the effect of stress of the component on the temperatures is negligible. The experiment instrumentation (measurement types, sensor types, sensor locations, sensor placements, measurement intervals) and the measurements are presented. The temperatures and distortions from the simulations show good correlation with experimental measurements. Ongoing modeling work is also briefly discussed.

Additive Manufacturing↗