Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RELEASE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

The Effect of Birthrate Granularity on the Release- to- Birth Ratio for the AGR-1 In-core Experiment

The AGR-1 Advanced Gas Reactor (AGR) tristructural-isotropic-particle fuel experiment underwent 13 irradiation intervals from December 2006 until November 2009 within the Idaho National Laboratory Advanced Test Reactor in support of the Next Generation Nuclear Power Plant program. During this multi-year experiment, release-to-birth rate ratios were computed at the end of each operating interval to provide information about fuel performance. Fission products released during irradiation were tracked daily by the Fission Product Monitoring System using 8-hour measurements. Birth rates calculated by MCNP with ORIGEN for as-run conditions were computed at the end of each irradiation interval. Each time step in MCNP provided neutron flux, reaction rates and AGR-1 compact composition, which were used to determine birth rates using ORIGEN. The initial birth-rate data, consisting of four values for each irradiation interval at the beginning, end, and two intermediate times, were interpolated to obtain values for each 8-hour activity. The problem with this method is that any daily changes in heat rates or perturbations, such as shim control movement or core/lobe power fluctuations, would not be reflected in the interpolated data and a true picture of the system would not be presented. At the conclusion of the AGR-1 experiment, great efforts were put forth to compute daily birthrates, which were reprocessed with the 8-hour release activity. The results of this study are presented in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Implementation of a new gamma spectrometer on the MERARG loop: Application to the volatile fission products release measurement

The MERARG facility initially aims at the annealing of irradiated fuel samples to study the gaseous fission products release kinetics. In order to complete the evaluation of the source term potentially released during accidental situation, the MERARG experimental circuit has been enhanced with a new gamma spectrometer. This one is directly sighting the fuel and is devoted to the fission products release kinetics. Because of the specificities of the fuel measurements, it has been dimensioned and designed to match the specific requirements. The acquisition chain and the collimation system have been optimized for this purpose and a first set of two experiments have shown the good functioning of this new spectrometry facility. (authors)

42 ENGINEERING↗

Increasing of MERARG experimental performances: on-line fission gas release measurement by mass spectrometry

The MERARG device - implemented at the LECASTAR Hot Laboratory, at the CEA Cadarache - allows characterizing nuclear fuels with respect to the behaviour of fission gases during thermal transients representative of normal or off normal operating nuclear power plant conditions. The fuel is heated in order to extract a part or the total gas inventory it contains. Fission Gas Release (FGR) is actually recorded by mean of both on-line gamma spectrometry station and micro gas chromatography. These two devices monitor the quantity and kinetics of fission gas release rate. They only address {sup 85}Kr radioactive isotope and the elemental quantification of Kr, Xe and He (with a relatively low detection limit in the latter case, typically 5-10 ppm). In order to better estimate the basic mechanisms that promote fission gas release from irradiated nuclear fuels, the CEA fuel study department decided to improve its experimental facility by modifying MERARG to extend the studies of gamma emitter fission gases to all gases (including Helium) with a complete isotopic distribution capability. To match these specifications, a Residual Gas Analyser (RGA) has been chosen as mass spectrometer. This paper presents a review of the main aspects of the qualification/calibration phase of the RGA type analyser. In particular, results recorded over three mass ranges 1-10 u, 80-90 u and 120-140 u in the two classical modes of MERARG, i.e. on-line and off-line measurements are discussed. Results obtained from a standard gas bottle show that the quantitative analysis at a few ppm levels can be achieved for all isotopes of Kr and Xe, as well as masses 2 and 4 u. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of fission product releases obtained from KueFA safety tests in light of the setup's accuracy - 18692

The Cold Finger Apparatus (KuehlFinger-Apparatur - KueFA) at the European Commission's JRC-Karlsruhe has been designed to assess the effects of Depressurization Loss of Forced Circulation (D-LOFC) accident scenarios on spherical irradiated High Temperature Reactor (HTR) fuel. At approximately 1600 deg. C, the reference maximum temperature for D-LOFC accidents, it has been observed that high-quality German HTR fuel pebbles release only a limited quantity of Cs but a significant amount of Ag. This paper revisits fission product release data obtained from the recently KueFA-tested fuel pebbles HFR-K5/3 and HFR-EU1/3 and presents associated investigations to improve the accuracy of the experimental setup. In light of these findings, implications for previously conducted KueFA heating tests are discussed, considering both experimental data as well as simulated release curves calculated with the Source Term Analysis Code system (STACY). (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Tritium Release Limit for Fluoride Salt-cooled High-temperature Reactors

Tritium generation is potentially a significant issue in Fluoride salt-cooled High-temperature Reactors (FHRs). Tritium in its molecular form, T{sub 2}, is highly permeable through reactor structure materials, especially under high temperatures. Since tritium presents a potential health hazard, its release must be controlled and mitigated. However, tritium release limit for FHRs is not specified in the current radiation protection regulations since FHRs are still being developed. This study first reviews related radiation protection regulations and literature before proposing a potential limit value of the tritium release rate for FHRs. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multiscale, mechanistic calculation of the effective silver diffusion coefficient in polycrystalline silicon carbide: application to silver release in AGR-1 TRISO particles

The silicon carbide (SiC) layer in tristructural isotropic (TRISO) fuel particles serves as a barrier to prevent the escape of fission from the fuel kernel. The release of silver (Ag) is a concern due to the long half-life of the 110mAg isotope. In this study, the effective diffusion coefficient of the fission product Ag through the grain boundary (GB) network is calculated using a combination of atomistic and phase-field methods. Atomistic calculations of Ag diffusivity in SiC bulk and GBs are leveraged to develop a mesoscale effective Ag diffusion coefficient (Deff) in SiC. Since GBs serve as pathways for Ag diffusion, Deff is defined as a function of temperature, microstructure variables, and fluence. Deff is implemented in the fuel performance code Bison to predict Ag release from AGR-1 TRISO fuel particles. We hereby quantify the impact of SiC grain size and irradiation on Ag release and improve Bison's predictions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Chitosan-Gated Magnetic-Responsive Nanocarrier for Dual-Modal Optical Imaging, Switchable Drug Release, and Synergistic Therapy

In this study, we present a multifunctional yet structurally simple nanocarrier that has a high drug loading capacity, releases drug in response to onset of an AC magnetic field, and can serve as a long-term imaging contrast agent and effectively kills cancer cells by synergistic action. This nanocarrier (HMMC-NC) has a spherical shell structure with a center cavity of 80 nm in diameter. The shell is comprised of two layers: an inner layer of magnetite that exhibits superparamagnetism and an outer layer of mesoporous carbon embedded with carbon dots that exhibit photoluminescence property. Thus in addition to being a drug carrier, HMMC-NC is also a contrast agent for bioimaging. The switchable drug release is enabled by the chitosan molecules attached on the nanocarrier as the switching material which turns on or off the drug release in response to the application or withdrawal of an AC magnetic field.

36 MATERIALS SCIENCE↗

Chemical–Switching Strategy for Synthesis and Controlled Release of Norcantharimides from a Biomass–Derived Chemical

Catalytic strategies were developed to synthesize and release chemicals for applications in fine chemicals, such as drugs and polymers, from a biomass-derived chemical, 5-hydroxymethyl furfural (HMF). The combination of the diene and aldehyde functionalities in HMF enabled catalytic production of acetalized HMF derivatives with diol or epoxy reactants to allow reversible synthesis of norcantharimide derivatives upon Diels-Alder reaction with maleimides. Reverse-conversion of the acetal group to an aldehyde yielded mismatches of the molecular orbitals in norcantharimides to trigger retro Diels-Alder reaction at ambient temperatures and released reactants from the coupled molecules under acidic conditions. In conclusion, these strategies provide for the facile synthesis and controlled release of high-value chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication of Biodegradable Superabsorbent Using RSM Design for Controlled Release of KNO{sub 3}

Present study envisaged the sequential experimental design approach for the development of biodegradable Gelatin-Tapoica/polyacrylamide superabsorbent. Percentage water uptake efficacy of candidate sample was optimized using Response Surface Methodology (RSM) design under microwave irradiation. Different process variables such as potassium persulphate and ammonium persulphate (KPS:APS) ratio, pH, reaction time concentration of acrylamide and N,N-methylene-bis-acrylamide (MBA) were investigated as a function of percentage swelling using sequential experimental design. Maximum liquid efficacy of 1550% was obtained at KPS:APS = 1.0:0.5; acrylamide = 7.67 × 10{sup −1} mol L{sup −1}; MBA = 1.76 × 10{sup −2} mol L{sup −1}; pH 10 and time = 110 s. The 3D crosslinked network formed was characterized using Fourier Transformation Infrared spectroscopy (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopic (SEM) techniques and thermal stability was ensured by Thermal gravimetric Analysis/Differential Thermal Analysis/Differential Thermal Gravimetric (TGA/DTA/DTG) studies. Superabsorbent synthesized could increase the moisture content in different type of soils and was found to enhance the water-holding capability of the soil upto 60 days in clayey, 40 days in sandy and 51 days in mixture of two soils under controlled conditions. Further, candidate polymer was investigated for the in-vitro controlled release of the KNO{sub 3} with diffusion exponent ‘n’ was found to be 0.4326 indicating Fickian type diffusion. Also, initial diffusion coefficient (D{sub I} = 3.49 × 10{sup −5} m{sup 2} h{sup −1}) was found to be greater than the lateral diffusion coefficient (D{sub L} = 3.76 × 10{sup −6} m{sup 2} h{sup −1}) indicated rapid release of KNO{sub 3} during initial hours with slow release afterwards. The ecofriendly nature of the synthesized polymer was also tested by conducting biodegradation studies and it was found to degrade upto 94% and 88.1% within 70 days with degradation rate of 1.34 and 1.26% per day using composting method and vermicomposting method respectively. So, the synthesized candidate polymer was found to be boon for agriculture-horticulture sector with wide applicability.

36 MATERIALS SCIENCE↗

Modeling Gas Transport in the Shallow Subsurface During the ZERT CO2 Release Test

We used the multiphase and multicomponent TOUGH2/EOS7CA model to carry out predictive simulations of CO{sub 2} injection into the shallow subsurface of an agricultural field in Bozeman, Montana. The purpose of the simulations was to inform the choice of CO{sub 2} injection rate and design of monitoring and detection activities for a CO{sub 2} release experiment. The release experiment configuration consists of a long horizontal well (70 m) installed at a depth of approximately 2.5 m into which CO{sub 2} is injected to mimic leakage from a geologic carbon sequestration site through a linear feature such as a fault. We estimated the permeability of the soil and cobble layers present at the site by manual inversion of measurements of soil CO{sub 2} flux from a vertical-well CO{sub 2} release. Based on these estimated permeability values, predictive simulations for the horizontal well showed that CO{sub 2} injection just below the water table creates an effective gas-flow pathway through the saturated zone up to the unsaturated zone. Once in the unsaturated zone, CO{sub 2} spreads out laterally within the cobble layer, where liquid saturation is relatively low. CO{sub 2} also migrates upward into the soil layer through the capillary barrier and seeps out at the ground surface. The simulations predicted a breakthrough time of approximately two days for the 100kg d{sup -1} injection rate, which also produced a flux within the range desired for testing detection and monitoring approaches. The seepage area produced by the model was approximately five meters wide above the horizontal well, compatible with the detection and monitoring methods tested. For a given flow rate, gas-phase diffusion of CO{sub 2} tends to dominate over advection near the ground surface, where the CO{sub 2} concentration gradient is large, while advection dominates deeper in the system.

54 ENVIRONMENTAL SCIENCES↗

Roles of Solvent in the Catalytic Hydrogen Release from Liquid Organic Hydrogen Carriers: Chemical, Thermodynamical and Technological Aspects

A Liquid Organic Hydrogen Carrier (LOHC) enables the storage and transport of hydrogen at ambient pressures and temperatures in a safe and convenient form using current infrastructure. However, it is challenging to directly compare reactivity and selectivity for hydrogen release, especially when comparing the catalytic efficiencies of neat LOHCs to highly diluted LOHCs in different solvents, reaction conditions, and catalysts. This work evaluates the role of solvents in catalysis and quantifies the energy efficiency of the overall process. The presence of solvent dilutes the volumetric density of available hydrogen, but may be necessary to achieve optimal catalysts stability, reactivity, and product selectivity. With respect to the reaction conditions as determined by thermodynamics, solvents with higher vapor pressures than that of the carrier can cause the erroneous impression of a more favorable reaction equilibrium. Concerning energy efficiency, solvents can result in increased energy demand for hydrogen release as the inert solvent must be heated to reaction temperatures required for release of H 2 from the LOHC. Further, this work recommends that investigations of catalyst reactivity should be carried out at different ratios of solvent to LOHC to understand how the reactivity changes and what the implications are for maximizing energy density and catalyst stability and reactivity. Investigations should also consider how these implications will affect the technical needs of applications intended for the LOHC system. Based on the results of this study, it is advised to focus research activities on LOHC systems with a gravimetric solvent content below about 50% as the thermodynamic disadvantages become very pronounced beyond this threshold.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Gas Release Behavior of Cu-TiH{sub 2} Composite Powder and Its Application as a Blowing Agent to Fabricate Aluminum Foams with Low Porosity and Small Pore Size

Compared to traditional pore structure with high porosity (≥ 80 pct) and large pore size (≥ 3 mm), aluminum foams with low porosity (60 to 70 pct) and small pore size (≤ 2 mm) possess higher compressive property and formability. In order to achieve the goal of reducing pore size, Cu-TiH{sub 2} composite powder prepared by ball milling preoxidized TiH{sub 2} with Cu powder was used as a blowing agent. Its gas release behavior was characterized by thermogravimetric analysis and differential scanning calorimetry. The results show that the ball milling treatment can advance the gas release process and slow the gas release rate at the same time. All these changes are favorable to the reduction of porosity and pore size. Such Cu-TiH{sub 2} composite powder provides an alternative way to fabricate aluminum foams with low porosity and small pore size.

36 MATERIALS SCIENCE↗

Antifouling Properties and Release of Dissolved Copper of Cold Spray Cu/Cu{sub 2}O Coatings for Ships and Steel Structures in Marine Environment

At the submarine screen doors of ships, the flow of water was fast and organic coatings were easy to peel off. To solve the problems of biofouling, the Cu/Cu{sub 2}O coatings were prepared by cold spray technology. In this paper, the release mechanism of effective antifouling components of the coatings was studied by micro-domain electrochemical potential scanning technique. Cuprous oxide in the coatings and the surrounding copper constituted micro-cells which accelerated the local electrochemical dissolution of copper. Cuprous oxide acted as the cathode, and the surrounding copper acted as the anode. Meanwhile, under the action of current, chloride ions were transferred from cathode to the anode and promoted local electrochemical dissolution of copper. Experiments show that the higher the Cu{sub 2}O content in the coatings, the greater the release rate of dissolved copper and inhibitory effect on diatoms. In the environments varied in dissolved oxygen, salinity, temperature and flow rate, the coatings maintained sufficient release rate of dissolved copper, unless the salinity was very low. Most of the dissolved copper was provided by the electrochemical dissolution process of copper. Whether in the indoor test or marine environment experiments, 30% Cu{sub 2}O coatings show the best performance. After insulating layer was sprayed, the effect of antifouling was improved evidently and the coatings were applied to the submarine screen doors of ships.

36 MATERIALS SCIENCE↗

Characteristics of cyclic heat release variability in the transition from spark ignition to HCCI in a gasoline engine

We study selected examples of previously published cyclic heat-release measurements from a single-cylinder gasoline engine as stepwise valve timing adjustments were made to shift from spark ignited (SI) combustion to homogeneous charge compression ignition (HCCI). Wavelet analysis of the time series, combined with conventional statistics and multifractal analysis, revealed previously undocumented features in the combustion variability as the shift occurred. In the spark-ignition combustion mode, the heat-release variations were very small in amplitude and exhibited more persistent low-frequency oscillations with intermittent high-frequency bursts. In the HCCI combustion mode, the amplitude of the heat-release variations again was small and involved mainly low-frequency oscillations. At intermediate states between SI and HCCI, a wide range of very large-amplitude oscillations occurred, including both persistent low-frequency periodicities and intermittent high-frequency bursts. It appears from these results that real-time wavelet decomposition of engine cylinder pressure measurements may be useful for on-board tracking of SI HCCI combustion regime shifts.

33 ADVANCED PROPULSION SYSTEMS↗

Solubility controls on plutonium and americium release in subsurface environments exposed to acidic processing wastes

To identify the role of waste composition and sediment interactions in controlling Pu and Am mobility in contaminated sediments at Hanford, a legacy nuclear site, Pu and Am concentrations in solutions equilibrated with contaminated sediments from beneath the 216-Z-9 (Z-9) Trench were compared to the solubilities of PuO 2 materials, synthesized by methods representative of the disposed wastes, in the absence of sediments. Furthermore, this work shows that the solubilities of PuO 2 materials synthesized by different methods, and with varying particle sizes, agree with PuO 2 (am,hyd), although dissolution kinetics differed between materials. According to saturation index (SI) calculations, PuO 2 (am,hyd) is likely also controlling Pu release from sediments under conditions where phosphate concentrations are low. However, both Pu-phosphate and Am-phosphate phases, identified in SI calculations and by high resolution transmission electron microscopy, play roles in controlling release in low pH, high phosphate, shallow sediments just below the Z-9 Trench. The elevated phosphate is likely due to decomposition of tributyl phosphate from waste solutions over time. Sediments from deeper in the subsurface beneath the Z-9 Trench are less acidic and contain less phosphate, with Pu solubility likely controlled by PuO 2 (am,hyd) that precipitated following neutralization of the acidic waste stream. Controls on Am concentrations in deeper sediments are more complex and potentially involve sediment adsorption and/or release from Pu (1-x) Am x O 2 following Am in-growth. The concentrations of both Pu and Am were elevated in the colloidal fraction associated with shallow sediments, but not in PuO 2 experiments, suggesting the presence of Pu/Am pseudocolloids (e.g., Pu/Am associated with mineral colloids). However, Pu and Am association with the colloidal size fraction was not observed in deeper sediments, suggesting transport of Pu and Am to these depths beneath the Z-9 Trench was not due to colloidal transport.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

A CASE STUDY OF CHLORINE TRANSPORT AND FATE FOLLOWING A LARGE ACCIDENTAL RELEASE

A train derailment that occurred in Graniteville, South Carolina during the early morning hours of 06 January, 2005 resulted in the prompt release of approximately 60 tons of chlorine to the environment. Comprehensive modeling of the transport and fate of this release was performed including the characterization of the initial three-phased chlorine release, a detailed determination of the local atmospheric conditions acting to generate, disperse, and deplete the chlorine vapor cloud, the establishment of physical exchange mechanisms between the airborne vapor and local surface waters, and local aquatic dilution and mixing.

54 ENVIRONMENTAL SCIENCES↗

1,5-Anhydro-D-fructose attenuates lipopolysaccharide-induced cytokine release via suppression of NF-{kappa}B p65 phosphorylation

Lipopolysaccharide (LPS) stimulates macrophages by activating NF-{kappa}B, which contributes to the release of tumor necrosis factor (TNF)-{alpha} and interleukin (IL)-6. 1,5-anhydro-D-fructose (1,5-AF), a monosaccharide formed from starch and glycogen, exhibits anti-oxidant activity and enhances insulin secretion. This study examined the effects of 1,5-AF on LPS-induced inflammatory reactions and elucidated its molecular mechanisms. Before LPS challenge, mice were pretreated with 1,5-AF (38.5 mg/kg). We found that 1,5-AF pretreatment attenuated cytokine release into the serum, including TNF-{alpha}, IL-6 and macrophage chemoattractant protein (MCP)-1. Furthermore, pretreatment with 1,5-AF (500 {mu}g/ml) attenuated cytokine release, and 1,5-AF directly inhibited the nuclear translocalization of the NF-{kappa}B p65 subunit in LPS-stimulated murine macrophage-like RAW264.7 cells. This inhibition was responsible for decreased LPS-induced phosphorylation on Ser536 of the NF-{kappa}B p65 subunit, which is a posttranslational modification involved in the non-canonical pathway. Collectively, these findings indicate that the anti-inflammatory activity of 1,5-AF occurs via inactivation of NF-{kappa}B.

60 APPLIED LIFE SCIENCES↗

Minocycline attenuates both OGD-induced HMGB1 release and HMGB1-induced cell death in ischemic neuronal injury in PC12 cells

High mobility group box-1 (HMGB1), a non-histone DNA-binding protein, is massively released into the extracellular space from neuronal cells after ischemic insult and exacerbates brain tissue damage in rats. Minocycline is a semisynthetic second-generation tetracycline antibiotic which has recently been shown to be a promising neuroprotective agent. In this study, we found that minocycline inhibited HMGB1 release in oxygen-glucose deprivation (OGD)-treated PC12 cells and triggered the activation of p38mitogen-activated protein kinase (MAPK) and extracellular signal-regulated kinases (ERK1/2). The ERK kinase (MEK)1/2 inhibitor U-0126 and p38MAPK inhibitor SB203580 blocked HMGB1 release in response to OGD. Furthermore, HMGB1 triggered cell death in a dose-dependent fashion. Minocycline significantly rescued HMGB1-induced cell death in a dose-dependent manner. In light of recent observations as well as the good safety profile of minocycline in humans, we propose that minocycline might play a potent neuroprotective role through the inhibition of HMGB1-induced neuronal cell death in cerebral infarction.

60 APPLIED LIFE SCIENCES↗