Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Synthesis of LiNiO 2 at Moderate Oxygen Pressure and Long-Term Cyclability in Lithium-Ion Full Cells

The widespread adoption of electric vehicles necessitates higher-energy-density and longer-life cathode materials for Li-ion batteries. LiNiO 2 offers a higher energy density at a lower cost than other high-Ni-content cathodes containing additional transition-metal ions. However, detrimental phase transformations and impedance growth, resulting from structural defects formed during synthesis, lead to poor cyclability and limit the practical viability of LiNiO 2 . Herein, we demonstrate a considerably improved cycle life for LiNiO 2 by synthesizing it under a pressurized oxygen environment. The capacity retention in pouch-type full cells with a graphite anode after 1000 cycles is increased from 59 to 76% by applying a mere 1.7 atm of oxygen pressure during the synthesis of LiNiO 2 . With iodometric titration and inductively coupled plasma optical emission spectroscopy analysis, we provide clear evidence that oxygen pressure during synthesis reduces the occurrence of lattice oxygen vacancies and increases the content of Ni 3+ in LiNiO 2 , improving its structural integrity and cyclability. Post-mortem analysis of the cycled cathodes provides insights into the sources of degradation occurring during long-term cycling. Here, this work demonstrates a practically viable, synthetic approach combined with doping and coating to achieve improved performance with high-Ni layered oxide materials. Furthermore, this work represents the first report of extended cycling of LiNiO 2 in pouch full cells with graphite anode and will, therefore, serves as an important benchmark for future research on LiNiO 2 .

25 ENERGY STORAGE↗

Pressure-Induced Amorphization and Polyamorphism in One-Dimensional Single-Crystal TiO[subscript 2] Nanomaterials

The structural phase transitions of single-crystal TiO{sub 2}-B nanoribbons were investigated in situ at high pressure using synchrotron X-ray diffraction and Raman scattering. Our results have shown a pressure-induced amorphization (PIA) occurred in TiO{sub 2}-B nanoribbons upon compression, resulting in a high-density amorphous (HDA) form related to the baddeleyite structure. Upon decompression, the HDA form transforms to a low-density amorphous (LDA) form, while the samples still maintain their pristine nanoribbon shape. A high-resolution transmission electron microscopy (HRTEM) image reveals that the LDA phase has an {alpha}-PbO{sub 2} structure with short-range order. We propose a homogeneous nucleation mechanism to explain the pressure-induced amorphous phase transition in the TiO{sub 2}-B nanoribbons. Our study demonstrates for the first time that PIA and polyamorphism occurred in the one-dimensional (1D) TiO{sub 2} nanomaterials and provides a new method for preparing 1D amorphous nanomaterials from crystalline nanomaterials.

36 MATERIALS SCIENCE↗

Development of a new type of high pressure calorimetric cell, mechanically agitated and equipped with a dynamic pressure control system: Application to the characterization of gas hydrates

A novel prototype of calorimetric cell has been developed allowing experiments under pressure with an in situ agitation system and a dynamic control of the pressure inside the cell. The use of such a system opens a wide range of potential practical applications for determining properties of complex fluids in both pressurized and agitated conditions. The technical details of this prototype and its calibration procedure are described, and an application devoted to the determination of phase equilibrium and phase change enthalpy of gas hydrates is presented. Our results, obtained with a good precision and reproducibility, were found in fairly good agreement with those found in literature, illustrate the various interests to use this novel apparatus.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Volume collapse phase transitions in cerium-praseodymium alloys under high pressure

Cerium-12at%Praseodymium(Ce 0.88 Pr 0.12 ) and Ce-50at%Praseodymium(Ce 0.50 Pr 0.50 ) alloy samples that contain a random solid-solution of Ce (4f1 (J=5/2)) and Pr (4f2 (J=4)) localized f-states have been studied by angle dispersive x-ray diffraction in a diamond anvil cell to a pressure of 65 GPa and 150 GPa respectively using a synchrotron source. Ce 0.88 Pr 0.12 alloy crystallizes in a face-centered cubic (γ-phase) structure at ambient conditions, while Ce 0.50 Pr 0.50 alloy crystallizes in the double hexagonal close packed (dhcp) structure at ambient conditions. Two distinct volume collapse transitions are observed in Ce 0.88 Pr 0.12 alloy at 1.5 GPa and 18 GPa with volume change of 8.5% and 3% respectively. In contrast, Ce 0.50 Pr 0.50 alloy shows only a single volume collapse of 5.6% at 20 GPa on phase transformation to α-Uranium structure under high pressure. Electrical transport measurements under high pressure show anomalies in electrical resistance at phase transitions for both compositions of this alloy.

36 MATERIALS SCIENCE↗

High pressure-temperature polymorphism of 1,1-diamino-2,2-dinitroethylene

Here, 1,1-diamino-2,2-dinitroethylene (FOX-7) is a low sensitivity energetic material with performance comparable to commonly used secondary explosives such as RDX and HMX. At ambient pressure, FOX-7 exhibits complex polymorphism with at least three structurally distinct phases (α, β, and γ). In this study, we have investigated the high pressure-temperature stability of FOX-7 polymorphs using synchrotron mid-infrared (MIR) spectroscopy. At ambient pressure, our MIR spectra and corresponding differential scanning calorimetry (DSC) measurements confirmed the known α → β (~110 °C) and β → γ (~160 °C) structural phase transitions; as well as, indicated an additional transition γ → δ (~210 °C), with the δ phase being stable up to ~251 degree C prior to decomposition. In situ MIR spectra obtained during isobaric heating at 0.9 GPa, revealed a potential α → β transition that could occur as early as 180 degree C, while β → β+δ phase transition shifted to ~300 °C with suppression of γ phase. Decomposition was observed slightly above 325 °C at 0.9 GPa..

36 MATERIALS SCIENCE↗

Formation of short-range magnetic order and avoided ferromagnetic quantum criticality in pressurized LaCrGe 3

LaCrGe 3 has attracted attention as a paradigm example of the avoidance of ferromagnetic (FM) quantum criticality in an itinerant magnet. In this work, we combined thermodynamic (specific heat and thermal expansion), transport, x-ray, and neutron scattering as well as μSR measurements to obtain insights on the temperature-pressure phase diagram of LaCrGe 3 . Consistent with previous studies of the phase diagram by transport measurements, our thermodynamic data shows clearly that the FM transition at T FM changes its character from second order to first order when it is suppressed to low temperatures by pressure. In addition, previous studies demonstrated that for high pressures a new phase occurs below T 2 , which was proposed to be a long-wavelength antiferromagnetic state (AFM q ). In this paper, we provide evidence from our thermodynamic data that this phase transition is preceded by yet another phase transition at T 1 >T 2 . Our μSR data indicate that full magnetic volume fraction is only established below T 2 , but that this magnetism is characterized by a short correlation length. Within the experimental resolution, our neutron-scattering data is not able to identify any magnetic Bragg peaks. Overall, the microscopic magnetic data is therefore consistent with the formation of FM clusters in the proximity of the avoided FM quantum critical point in LaCrGe 3 . This conclusion is at odds with the previous proposal of AFM q order and raises questions on the role of disorder in this stochiometric compound.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pressure-induced transformations in amorphous Si-Ge alloy

The pressure behavior of an amorphous Si-rich SiGe alloy ({alpha}-Si{sub x}Ge{sub 1-x}, x = 0.75) has been investigated up to about 30 GPa, by a combination of Raman spectroscopy, x-ray absorption spectroscopy, and x-ray diffraction measurements. The trends of microscopic structural properties and of the Raman-active phonon modes are presented in the whole pressure range. Nucleation of nanocrystalline alloy particles and metallization have been observed above 12 GPa, with a range of about 2 GPa of coexistence of amorphous and crystalline phases. Transformations from the amorphous tetrahedral, to the crystalline tetragonal ({beta}-Sn) and to the simple hexagonal structures have been observed around 13.8 and 21.8 GPa. The recovered sample upon depressurization, below about 4 GPa, shows a local structure similar to the as-deposited one. Inhomogeneities of the amorphous texture at the nanometric scale, probed by high-resolution transmission electron microscopy, indicate that the recovered amorphous sample has a different ordering at this scale, and therefore the transformations can not be considered fully reversible. The role of disordered grain boundaries at high pressure and the possible presence of a high-density amorphous phase are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Steel–Concrete Composite Pressure Vessels for Hydrogen Storage at High Pressures

The need to store large quantities of hydrogen in large diameter steel vessels under high pressures results in shell thicknesses that are too large to produce by most steel mills and not practical to fabricate. Accordingly, a research program was undertaken by Oak Ridge National Laboratory to develop a new concept of combining steel with concrete to construct such vessels economically and practically. The concept is to fabricate vessels where the steel shell thickness is approximately one half that required to resist the hoop forces due to internal pressure. As such, the steel shell is designed to carry the full amount of the longitudinal forces in the vessel but only one half of the hoop loads due to internal pressure. The other half of the hoop loads is carried by a prestressed and reinforced concrete shell. In large diameter vessels, the cost of the shell can further be reduced by using layered steel shell construction rather than solid-wall construction. Such shell construction has also the added advantage of easily venting the hydrogen that permeates through the steel shell directly to the atmosphere through vent holes. This mechanism prevents the hydrogen from damaging the steel shell. The theoretical formulation of the steel concrete shell design is presented in this paper. Finally, in addition, details of a full-scale mock up vessel designed, fabricated, and tested to prove the proposed methodology are given.

42 ENGINEERING↗

High Pressure Brillouin Spectroscopy and X-ray Diffraction of Cerium Dioxide

Simultaneous high-pressure Brillouin spectroscopy and powder X-ray diffraction of cerium dioxide powders are presented at room temperature to a pressure of 45 GPa. Micro- and nanocrystalline powders are studied and the density, acoustic velocities and elastic moduli determined. In contrast to recent reports of anomalous compressibility and strength in nanocrystalline cerium dioxide, the acoustic velocities are found to be insensitive to grain size and enhanced strength is not observed in nanocrystalline CeO 2 . Discrepancies in the bulk moduli derived from Brillouin and powder X-ray diffraction studies suggest that the properties of CeO 2 are sensitive to the hydrostaticity of its environment. Our Brillouin data give the shear modulus, G 0 = 63 (3) GPa, and adiabatic bulk modulus, K S0 = 142 (9) GPa, which is considerably lower than the isothermal bulk modulus, K T0 ~ 230 GPa, determined by high-pressure X-ray diffraction experiments.

36 MATERIALS SCIENCE↗

High Temperature Dynamic Pressure Measurements Using Silicon Carbide Pressure Sensors

Un-cooled, MEMS-based silicon carbide (SiC) static pressure sensors were used for the first time to measure pressure perturbations at temperatures as high as 600 C during laboratory characterization, and subsequently evaluated in a combustor rig operated under various engine conditions to extract the frequencies that are associated with thermoacoustic instabilities. One SiC sensor was placed directly in the flow stream of the combustor rig while a benchmark commercial water-cooled piezoceramic dynamic pressure transducer was co-located axially but kept some distance away from the hot flow stream. In the combustor rig test, the SiC sensor detected thermoacoustic instabilities across a range of engine operating conditions, amplitude magnitude as low as 0.5 psi at 585 C, in good agreement with the benchmark piezoceramic sensor. The SiC sensor experienced low signal to noise ratio at higher temperature, primarily due to the fact that it was a static sensor with low sensitivity.

Pressure Sensors↗

DEVELOPMENT OF ASME SECTION X CODE RULES FOR HIGH PRESSURE COMPOSITE HYDROGEN PRESSURE VESSELS WITH NON-LOAD SHARING LINERS

The Boiler and Pressure Vessel Project Team on Hydrogen Tanks was formed in 2004 to develop Code rules to address the various needs that had been identified for the design and construction of up to 15000 psi hydrogen storage vessel. One of these needs was the development of Code rules for high pressure composite vessels with non-load sharing liners for stationary applications. In 2009, ASME approved new Appendix 8, for Section X Code which contains the rules for these vessels. These vessels are designated as Class III vessels with design pressure ranging from 20.7 MPa (3,000 ps)i to 103.4 MPa (15,000 psi) and maximum allowable outside liner diameter of 2.54 m (100 inches). The maximum design life of these vessels is limited to 20 years. Design, fabrication, and examination requirements have been specified, included Acoustic Emission testing at time of manufacture. The Code rules include the design qualification testing of prototype vessels. Qualification includes proof, expansion, burst, cyclic fatigue, creep, flaw, permeability, torque, penetration, and environmental testing.

08 HYDROGEN↗