Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Navigation Errors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Mariner Venus/Mercury 1973 navigation strategy

This paper presents the navigational aspects of the Mariner Venus/Mercury 1973 mission. Principal emphasis is on the development of the trajectory correction strategy, propellant costs, and delivery accuracies at Venus and Mercury. Key error sources and mission constraints are discussed. Of particular interest are the statistics of the first, post-Venus, maneuver which must correct for the magnification of errors in the Venus encounter. Finally, although not a primary objective of the mission, the analysis is extended to include a second Mercury encounter.

Mckinley, E. L.↗
NASA NTRS1981

Navigation accuracy analysis for a Halley intercept mission

A ballistic intercept mission to Comet Halley is currently under consideration by the United States. This paper describes the navigation system and the navigation strategy which would be employed in such a mission, assuming a launch in the summer of 1985 and an arrival in March of 1986. Spacecraft comet-relative orbit determination accuracies are presented as functions of time for the baseline navigation strategy, along with the results of a number of parametric sensitivity studies involving parameters such as data frequencies, data accuracies, stochastic acceleration levels, cometary ephemeris uncertainties, maneuver execution errors, and encounter date.

Wood, L. J.↗
NASA NTRS1982

Attitude and translation control of a low-altitude Gravsat

Dynamic simulation of the Gravsat's attitude and translation control system is used to provide an upper bound for the fuel supply and test the feasibility of the preliminary design. A preliminary design is made for the disturbance compensation system (DISCOS) sensor, the thruster control laws, reaction wheel control laws, and the onboard state estimators. The sensor analysis and noise measurements show no problems in scaling the Triad navigation satellite sensor design up to meet the Gravsat requirements, except for proof mass center-of-mass offset. A promising technique is proposed to measure and eliminate this error. The covariance analysis confirms that a sophisticated post-flight data fit will be necessary to reconstruct a scientifically useful proof mass state. The DISCOS sensor will have to be continuously calibrated from the inflight data to achieve this reconstruction.

Ray, J. C.↗
NASA NTRS2007

Benefits Derived From Laser Ranging Measurements for Orbit Determination of the GPS Satellite Orbit

While navigation systems for the determination of the orbit of the Global Position System (GPS) have proven to be very effective, the current research is examining methods to lower the error in the GPS satellite ephemerides below their current level. Two GPS satellites that are currently in orbit carry retro-reflectors onboard. One notion to reduce the error in the satellite ephemerides is to utilize the retro-reflectors via laser ranging measurements taken from multiple Earth ground stations. Analysis has been performed to determine the level of reduction in the semi-major axis covariance of the GPS satellites, when laser ranging measurements are supplemented to the radiometric station keeping, which the satellites undergo. Six ground tracking systems are studied to estimate the performance of the satellite. The first system is the baseline current system approach which provides pseudo-range and integrated Doppler measurements from six ground stations. The remaining five ground tracking systems utilize all measurements from the current system and laser ranging measurements from the additional ground stations utilized within those systems. Station locations for the additional ground sites were taken from a listing of laser ranging ground stations from the International Laser Ranging Service. Results show reductions in state covariance estimates when utilizing laser ranging measurements to solve for the satellite s position component of the state vector. Results also show dependency on the number of ground stations providing laser ranging measurements, orientation of the satellite to the ground stations, and the initial covariance of the satellite's state vector.

Welch, Bryan W.↗
NASA NTRS2021

Isolation in Compact Magnetically-loaded Tri-axial Magneto-quasistatic Detectors

A navigation technique using quasistatic magnetic field had been an active R\&{}D topic for a while. One parameter to measure the performance of such technique is to quantify the error between calculated and actual position across a range. Several factors could contribute to the overall range error, among which is the field receiving antenna. This paper describes a laboratory experiment conducted to measure the frequency response of the antenna to understand how well it can isolate field component orthogonal to each coil's axis. The measurements were used to infer what range error could the antenna contribute to the overall technique.

Peng, Nicholas S↗
NASA NTRS1975

System design impact of guidance and navigation analysis for a SEPS 1979 Encke flyby

Baseline guidance and navigation strategy for an ecliptic projection of the Encke flyby mission consider solar electric propulsion stage parameters in generating optimized and targeted trajectory control. Results show the Encke relative approach error to be dominated by ephemerical uncertainties, particularly the velocity components.

Hong, P.↗
NASA NTRS1982

Space Shuttle Orbiter onboard rendezvous navigation

Much of the work that the Space Shuttle will perform requires a capability to rendezvous with other orbiting objects. The formulation and design philosophy behind the Space Shuttle Orbiter rendezvous navigation system are the subjects of this paper. The current rendezvous navigation design incorporates a Kalman filter to estimate the relative position and velocity. The filter is augmented with state elements for the estimation of colored measurement noise and acceleration modeling errors. Several measurement types are available to the filter: a manual optical sighting device, an automatic optical tracking instrument, and a rendezvous radar which provides range and range rate measurements as well as the line of sight direction. The filter also includes a technique for detecting highly improbable measurements and excluding them from Kalman processing.

Little, M. J.↗
NASA NTRS2004

Mitigation of the Impact of Sensing Noise on the Precise Formation Flying Control Problem

The specific objectives of this proposed research were: 1. Further investigation into the impact of CDGPS sensing errors for high Earth orbit missions. 2. Identify augmentation approaches of the CDGPS that will improve the relative state for low and high Earth orbit missions. 3. Integration of the navigation and control concepts into the GSFC Formation Flying Testbed. In addition this was a cooperative effort with Dr. Jonathan How at MIT. Dr. Alfriend was to spend two weeks working with Dr. How and his students. The travel for these two weeks was paid by the Texas Engineering Experiment Station (TEES) as cost sharing.

Alfriend, K. T.↗
NASA NTRS2005

Sensor Data Distribution With Robustness and Reliability: Toward Distributed Components Model

In planetary surface exploration mission, sensor data distribution is required in many aspects, for example, in navigation, scheduling, planning, monitoring, diagnostics, and automation of the field tasks. The challenge is to distribute such data in the robust and reliable way so that we can minimize the errors caused by miscalculations, and misjudgments that based on the error data input in the mission. The ad-hoc wireless network on planetary surface is not constantly connected because of the nature of the rough terrain and lack of permanent establishments on the surface. There are some disconnected moments that the computation nodes will re-associate with different repeaters or access points until connections are reestablished. Such a nature requires our sensor data distribution software robust and reliable with ability to tolerant disconnected moments. This paper presents a distributed components model as a framework to accomplish such tasks. The software is written in Java and utilized the available Java Message Services schema and the Boss implementation. The results of field experimentations show that the model is very effective in completing the tasks.

Alena, Richard L.↗
NASA NTRS1980

RAMP: A fault tolerant distributed microcomputer structure for aircraft navigation and control

RAMP consists of distributed sets of parallel computers partioned on the basis of software and packaging constraints. To minimize hardware and software complexity, the processors operate asynchronously. It was shown that through the design of asymptotically stable control laws, data errors due to the asynchronism were minimized. It was further shown that by designing control laws with this property and making minor hardware modifications to the RAMP modules, the system became inherently tolerant to intermittent faults. A laboratory version of RAMP was constructed and is described in the paper along with the experimental results.

Dunn, W. R.↗
NASA NTRS1971

Lunar surface navigation analysis

The accuracy of the crew position obtained by using a line-of-sight device such as a sun compass or the rover television camera and the prominent mountains such as Hadley and Hadley delta was investigated. It was determined that with errors of 1 deg (noise only), the crew position can be obtained to sigma sub phi = 850 feet and sigma sub lambda = 400 feet using Hadley and Hadley delta. The addition of West Mountain reduced the errors to 600 and 400 feet, respectively.

Savely, R. T.↗
DOE OSTI2021

System Calibration Including Time Delay Estimation for GNSS/INS-Assisted Pushbroom Scanners Onboard UAV Platforms

Unmanned aerial vehicles (UAVs ) equipped with imaging sensors and integrated global navigation satellite system/inertial navigation system (GNSS/INS ) units are used for numerous applications. Deriving reliable 3D coordinates from such UAVs is contingent on accurate geometric calibration, which encompasses the estimation of mounting parameters and synchronization errors. Through a rigorous impact analysis of such systematic errors, this article proposes a direct approach for spatial and temporal calibration (estimating system parameters through a bundle adjustment procedure) of a GNSS/INS -assisted pushbroom scanner onboard a UAV platform. The calibration results show that the horizontal and vertical accuracies are within the ground sampling distance of the sensor. Unlike for frame camera systems, this article also shows that the indirect approach is not a feasible solution for pushbroom scanners due to their limited ability for decoupling system parameters. This finding provides further support that the direct approach is recommended for spatial and temporal calibration of UAV pushbroom scanner systems.

47 OTHER INSTRUMENTATION↗
NASA NTRS1972

Improved navigation by combining VOR/DME information with air or inertial data

The improvement was determined in navigational accuracy obtainable by combining VOR/DME information (from one or two stations) with air data (airspeed and heading) or with data from an inertial navigation system (INS) by means of a maximum-likelihood filter. It was found that the addition of air data to the information from one VOR/DME station reduces the RMS position error by a factor of about 2, whereas the addition of inertial data from a low-quality INS reduces the RMS position error by a factor of about 3. The use of information from two VOR/DME stations with air or inertial data yields large factors of improvement in RMS position accuracy over the use of a single VOR/DME station, roughly 15 to 20 for the air-data case and 25 to 35 for the inertial-data case. As far as position accuracy is concerned, at most one VOR station need be used. When continuously updating an INS with VOR/DME information, the use of a high-quality INS (0.01 deg/hr gyro drift) instead of a low-quality INS (1.0 deg/hr gyro drift) does not substantially improve position accuracy.

Bobick, J. C.↗
NASA NTRS1982

A microcomputer-based position updating system for general aviation utilizing Loran-C

Modern digital electronic technology is used to produce a device to convert LORAN C to useful pilot information using a simple software algebra and low cost microprocessor devices. Results indicate that the processor based LORAN C navigator has an accuracy of 1.0 nm or less over an area typically covered by a triad of Loran C stations and can execute a position update in less than 0.2 seconds. The system was tested in 30 hours of flight and proved that it can give reliable and accurate navigation information. Methods of converting time differences to position, design considerations for the microcomputer system, and the system for coordinate conversion are discussed. Testing with predetermined points and possible fixes for errors are also considered.

Fischer, J. P.↗
NASA NTRS1987

Investigation of air transportation technology at Massachusetts Institute of Technology, 1984

Three projects sponsored by the Joint University Program at MIT are summarized. Two projects were focussed on the potential application of Loran-C in flying nonprecision approaches to general aviation runways, and the third project involved research on aircraft icing. In one Loran-C project, Aircraft Approach Guidance Using Relative Loran-C Navigation, the concept was flight tested. It used the difference in TD's from those of the touchdown point to simplify and speed navigation computer processing and took advantage of the short term accuracy of less than 100 feet for Loran-C. The goal of the project, Probabilistic Modelling of Loran-C Error for Nonprecision Approaches, was to develop a mathematical model which would predict the probability that an approach flown to a runway with a particular Loran-C receiver would fall within a given standard. The Aircraft Icing project focussed on measurement of droplet trajectories and droplet impingement/runback characteristics and measurement of real time ice accretion using ultrasonic pulse echo techniques.

Simpson, Robert W.↗
NASA NTRS1999

A Flight/Ground/Test Event Logging Facility

The onboard control software for spacecraft such as Mars Pathfinder and Cassini is composed of many subsystems including executive control, navigation, attitude control, imaging, data management, and telecommunications. The software in all of these subsystems needs to be instrumented for several purposes: to report required telemetry data, to report warning and error events, to verify internal behavior during system testing, and to provide ground operators with detailed data when investigating in-flight anomalies. Events can range in importance from purely informational events to major errors. It is desirable to provide a uniform mechanism for reporting such events and controlling their subsequent processing. Since radiation-hardened flight processors are several years behind the speed and memory of their commercial cousins, and since most subsystems require real-time control, and since downlink rates to earth can be very low from deep space, there are limits to how much of the data can be saved and transmitted. Some kinds of events are more important than others and should therefore be preferentially retained when memory is low. Some faults can cause an event to recur at a high rate, but this must not be allowed to consume the memory pool. Some event occurrences may be of low importance when reported but suddenly become more important when a subsequent error event gets reported. Some events may be so low-level that they need not be saved and reported unless specifically requested by ground operators.

Dvorak, Daniel↗
NASA NTRS2005

Handling Trajectory Uncertainties for Airborne Conflict Management

Airborne conflict management is an enabling capability for NASA's Distributed Air-Ground Traffic Management (DAG-TM) concept. DAGTM has the goal of significantly increasing capacity within the National Airspace System, while maintaining or improving safety. Under DAG-TM, autonomous aircraft maintain separation from each other and from managed aircraft unequipped for autonomous flight. NASA Langley Research Center has developed the Autonomous Operations Planner (AOP), an onboard decision support system that provides airborne conflict management (ACM) and strategic flight planning support for autonomous aircraft pilots. The AOP performs conflict detection, prevention, and resolution from nearby traffic aircraft and area hazards. Traffic trajectory information is assumed to be provided by Automatic Dependent Surveillance Broadcast (ADS-B). Reliable trajectory prediction is a key capability for providing effective ACM functions. Trajectory uncertainties due to environmental effects, differences in aircraft systems and performance, and unknown intent information lead to prediction errors that can adversely affect AOP performance. To accommodate these uncertainties, the AOP has been enhanced to create cross-track, vertical, and along-track buffers along the predicted trajectories of both ownship and traffic aircraft. These buffers will be structured based on prediction errors noted from previous simulations such as a recent Joint Experiment between NASA Ames and Langley Research Centers and from other outside studies. Currently defined ADS-B parameters related to navigation capability, trajectory type, and path conformance will be used to support the algorithms that generate the buffers.

Barhydt, Richard↗
NASA NTRS2010

Analysis and Testing of a LIDAR-Based Approach to Terrain Relative Navigation for Precise Lunar Landing

Capability for precise lunar landing is the goal for future NASA missions. A LIDAR-based terrain relative navigation (TRN) approach lets us achieve this goal and also land under any illumination conditions. Results from field test data showed that the LIDAR TRN algorithm obtained position estimates with mean error of about 20 meters and standard deviations of about 10 meters. Moreover, the algorithm was capable of providing 99 percent correct estimates by assessing the local terrain relief in the data. Also, the algorithm was able to handle initial position uncertainty of up to 1.6 kilometers without performance degradation.

laser altimeter↗