Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effects of Sodium Exposure on the Tensile Properties of Grade 91 steel

Two heats of G91 steel have been investigated in liquid sodium at 550- 650°C to understand their corrosion behaviour, microstructural evolution, and tensile properties. Sodium exposure experiments of subsized, sheet-type tensile specimens of G91 were performed in Argonne’s forced convection sodium materials testing loops, SMT-1 and SMT-2. Maximum exposure times of ~49,000 h at ~38,000 h, and ~20,000 h have been achieved at 550, 600, and 650°C, respectively. Thermal aging experiments of G91 steel were also conducted in parallel, and the results were compared with those of the sodium-exposed specimens to isolate the effect of thermal aging from the effect of sodium exposure. It was found that the yield stress and ultimate tensile strength of G91 were reduced by more than 50% after sodium exposures at 650°C due to decarburization. The reduction in tensile strength was accompanied by the dissolution of M 23 C 6 carbides and excessive grain growth. The effect of sodium at 550 and 600°C was insignificant for exposure times up to ~49,000 h and ~38,000 h, respectively. The effect of sodium on the microstructural stability and tensile properties of G91 is largely dependent on the carbon mass transfer in the alloy-sodium system.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2019

Effect of Heat Input on Microstructure, Residual Stress, and Corrosion Resistance of UNS 32101 Lean Duplex Stainless Steel Weld Joints

In the present work, the influence of heat input on phase balance, residual stresses and corrosion resistance of UNS 32101 lean duplex stainless steel welds has been investigated. Three weldment types were obtained with different heat inputs by varying welding current, using gas tungsten arc welding process. The results revealed that increasing heat input caused a significant microstructural evolution with high austenite fraction in weld metals. The residual stresses were measured on the surface and through the sample’s thickness by x-ray diffraction technique based on Sin{sup 2}ψ method. The results showed an inversely proportional relationship between the heat input and the compressive residual stresses on the surface and through the thickness of the weld metal. Potentiodynamic polarization tests of the different welded joints evaluated in 3.5% NaCl solution exhibited high corrosion resistance of the weld metal produced with the low heat input.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Experimental Study on Microstructure and Hardness of Pure Titanium Subjected to Torsion Deformation at Different Temperatures

The studies of mechanical property, microstructure evolution and fracture analysis in pure titanium processed by torsion deformation at 298, 673 and 1073 K are conducted systematically. The variations of mechanical property of deformed pure titanium are shown through Vickers hardness evaluation. During torsion at 298 K, the grains are refined and elongated, but the α phase with different shapes precipitates for twisted samples at 673 and 1073 K. The fracture appearance indicates that the elongated dimples occur on fracture surface at 298 K. Besides, a large number of shear facets are arranged. However, typical intergranular fracture appearance with lots of blocks in polyhedral shape covers the fracture surface at 673 and 1073 K, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗
NASA NTRS2014

Comparison of Directionally Solidified Samples Solidified Terrestrially and Aboard the International Space Station

This article reports research that has been carried out under the aegis of NASA as part of a collaboration between ESA and NASA for solidification experiments on the International Space Station (ISS). The focus has been on the effect of convection on the microstructural evolution and macrosegregation in hypoeutectic Al-Si alloys during directional solidification (DS). Terrestrial DS-experiments have been carried out at Cleveland State University (CSU) and under microgravity on the International Space Station (ISS). The thermal processing-history of the experiments is well defined for both the terrestrially processed samples and the ISS-processed samples. As of this writing, two dendritic metrics was measured: primary dendrite arm spacings and primary dendrite trunk diameters. We have observed that these dendrite-metrics of two samples grown in the microgravity environment show good agreements with models based on diffusion controlled growth and diffusion controlled ripening, respectively. The gravity-driven convection (i.e., thermosolutal convection) in terrestrially grown samples has the effect of decreasing the primary dendrite arm spacings and causes macrosegregation. Dendrite trunk diameters also show differences between the earth- and space-grown samples. In order to process DS-samples aboard the ISS, the dendritic seed crystals were partially remelted in a stationary thermal gradient before the DS was carried out. Microstructural changes and macrosegregation effects during this period are described and have modeled.

Angart, S.↗
NASA NTRSDate not supplied

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Monel K500 Alloy Fabricated Via L-PBF and LP-DED

This study examines and compares the effect of different heat treatments (HT) on the microstructure and mechanical properties of Monel K500 fabricated using laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) technologies. The as-fabricated Monel K500 specimens exhibited dendritic microstructure and elemental micro-segregation due to high cooling rates induced during the fabrication process. The applicability of HT proposed in the literature for wrought Monel K500 was investigated for L-PBF and LP-DED using four different HT procedures involving hot isostatic pressing (HIP), solution annealing (SA), and aging. The mechanical properties of test specimens were evaluated using uniaxial tensile testing at room temperature. The microstructural evolution of test specimens during HT was analyzed using a scanning electron microscope. For all HT conditions investigated, L-PBF Monel K500 specimens consistently displayed higher strength and lower ductility compared to the LP-DED counterparts. The HT procedure involving HIP at 1160°C for 3hr at 100 MPa, SA at 1100°C for 15 min, and three step aging at 610°C for 16 hr, 540°C for 6 hr, and 480°C for 8 hr resulted in highest strength for both L-PBF and LP-DED fabricated Monel K500.

Additive manufacturing↗
DOE OSTI2023

Irradiation creep measurement and microstructural analysis of chromium nitride–coated zirconium alloy using pressurized tubes

Environmental barrier coatings for Zr-based materials are currently under development to reduce oxidation and embrittlement in light-water reactors. Chromium nitride is one such candidate for this application, particularly as accident-tolerant fuel cladding. However, quantifying the impact of coatings on the irradiation-induced creep of zircaloy (Zry) is critical as this mechanism often exceeds thermal creep rates under light-water reactor operating conditions and can be a limiting design characteristic. Additionally, examining irradiation effects in the microstructure at the coating interface is key to understanding the compatibility of the material system. Here, to accelerate the experimental measurement of irradiation creep and microstructure evolution in CrN-Zry, compact, pressurized creep tubes were fabricated and irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. Miniature, thin-walled rodlets fabricated from annealed Zr-Sn barstock were coated with CrN using physical vapor deposition (PVD) to nominal thicknesses of 4 and 8 μm. Coated and uncoated rodlet specimens were internally pressurized and welded, generating nominal circumferential hoop stresses of 0, 90, or 180 MPa under 300°C irradiation conditions. Twelve specimens were measured diametrically prior to irradiation using a low-cost, automated, contactless laser profilometer developed for this work. Specimens were irradiated in sealed capsules for one 25-day HFIR cycle, accumulating approximately 1.8 $\times$ 10 21 n/cm 2 fast fluence (E n > 10 MeV). The irradiated samples were retrieved and remeasured using the same profilometry system in a shielded hot cell facility. Irradiation creep between specimens was compared using standard statistical tests and showed that both thicknesses of CrN coating had a negligible effect on the irradiation creep strain of the Zry material. Microstructure characterization of pre- and post-irradiated CrN-Zry specimens showed minimal changes due to irradiation but did show a substantial O-rich region at the Zry-CrN interface.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Phase Transformation of Thermally Aged and Neutron Irradiated Duplex Stainless Steel Used in LWRs. Final report

The lifetime of reactor components made of duplex stainless steels can be limited by the embrittlement from thermal aging, neutron irradiation or a synergistic effect between thermal aging and neutron irradiation. There is still a large scientific knowledge gap in understanding the phase evolution in duplex stainless steels upon thermal aging with or without neutron irradiation, the synergistic effect between thermal aging and neutron irradiation, and the impacts of structural evolution on material mechanical responses. In this project, totally, five major tasks were completed through this project: a) the in-situ WAXS tensile tests of thermally aged cast duplex stainless steels, b) the EXAFS investigation of thermally aged cast austenitic stainless steel and welds of austenite sainless steel, c) the characterization of irradiation effect on neutron irradiated CASS using APT, d) characterize the ferrite hardening of neutron irradiated CASS using nanoindentation, and e) the FEM modelling to validate the in-situ WAXS tensile tests and to simulate the stress/strain distribution during deformation for thermally aged duplex stainless steel. In summary, the thermal aging without neutron irradiation can significantly increase the strength of ferrite phase through the spinodal decomposition and G-phase precipitations. The in-situ X-ray experiments show that the hardening effect in ferrite phase can significantly alter the load partition between the ferrite and austenite phases. Atom probe tomography characterizations on samples irradiated to 0.08, 3, 5, 10, 20, and 40 dpa shows that neutron irradiation has dominated the microstructural evolution after 3 dpa, and the spinodal decomposition has saturated yet even at 40 dpa based on the quantified wavelength and amplitude.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Characterization of the degradation of gamma-irradiated elastomers using Raman spectroscopy

This report presents key findings from Raman spectroscopic analysis of gamma-irradiated rubber samples extracted from a laminated lead-damped rubber (LDR) seismic isolation device. The samples were exposed to gamma radiation from a 60Co source in a Foss Therapy Services gamma irradiator, reaching absorbed doses up to 1600 kGy. A distinct threshold near 400 kGy was identified, beyond which significant spectral changes were observed. Two Raman peaks - at approximately 425 cm-1 and 2440 cm-1 - were tracked as a function of dose using Gaussian fitting. The 425 cm-1 peak, attributed to sulfur–sulfur (S–S) bond stretching (resulting from vulcanization of the rubber), exhibited a dose-dependent upshift, indicating radiation-induced crosslinking within the sulfur-based polymer network. Conversely, the 2440 cm-1 peak, likely associated with vibrational modes of additives or impurities, showed a downward shift with increasing dose, suggesting chain scission and degradation of non-rubber constituents. These results provide first-of-a-kind insights into the microstructural evolution of elastomers under high-dose gamma irradiation and establish a preliminary dose threshold for significant degradation. Future work will incorporate multi-modal characterization—including Fourier Transform Infrared (FTIR) spectroscopy, scanning electrom microscopy (SEM) of the rubber surface morphology, thermogravimetric analysis (TGA) to determine changes in thermal stability, and mechanical testing—to correlate molecular-level changes with macroscopic performance of these elastomers as damping media in seismic isolation devices. These findings are expected to provide regulatory guidance and design criteria for qualifying low-damping rubber seismic isolators in advanced nuclear reactor applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Facile Interfacial Reduction Suppresses Redox Chemical Expansion and Promotes the Polaronic to Ionic Transition in Mixed Conducting (Pr,Ce)O 2−δ Nanoparticles

Mixed ionic/electronic conductors (MIECs) are essential components of solid-state electrochemical devices, such as solid oxide fuel/electrolysis cells. For efficient performance, MIECs are typically nanostructured, to enhance the reaction kinetics. However, the effect of nanostructuring on MIEC chemo-mechanical coupling and transport properties, which also impact cell durability and efficiency, has not yet been well understood. Here, in this work, Pr 0.2 Ce 0.8 O 2−δ (PCO20) nanopowders were prepared by coprecipitation, then sintered in a modified dilatometer at three different temperatures (600, 725, and 850 °C) for microstructure evolution, resulting in three samples with different average particle sizes (23, 30, and 53 nm). The chemical strain and electronic/ionic conductivity were then measured simultaneously on stable nanostructures in four isotherms from 550 to 400 °C with steps in pO 2 (1 to 10 –4 atm O 2 ). A microcrystalline bar was prepared and measured for comparison. Particle size reduction led to a monotonically decreasing isothermal redox chemical strain, confirmed by in situ high-temperature, controlled-atmosphere XRD measurements. The corresponding conductivity measurements provided defect chemical insight into the particle size-dependent chemical expansion behavior. The significant weakening of the pO 2 dependence and decreased activation energy for electrical conduction with decreasing particle size indicated a decrease in the reduction enthalpy of PCO, shifting the transition from (Pr) polaronic to ionic behavior to higher pO 2 . STEM-EELS measurements confirmed the majority of Pr was reduced to 3+ in the nanoparticles, while Ce remained 4+. These results demonstrate suppression of deleterious chemical expansion and tailoring of the dominant charge carrier simply through controlling the particle size, providing insights for MIEC microstructural design.

ceria↗
DOE OSTI2018

Mechanical Properties of the Mg-Gd-Y-Zn-Zr Alloys with Different Morphologies of Long-Period Stacking Ordered Phases

Long-period stacking ordered (LPSO) phases with different morphologies and distributions were obtained in the direct chill cast Mg-6.9Gd-3.2Y-1.5Zn-0.5Zr (wt.%) alloy by controlling the homogenization time or cooling rate. Microstructural evolution and the effect of various LPSO phases on the mechanical properties were investigated. There is no obvious α-Mg grain growth during homogenization at 510 °C. Intragranular thin-platelet and coagulated LPSO phases hardly improve the strength but help to develop the ductility. Numerous lamellar phases, which contain “ABCA”-type building blocks with RE and Zn segregation, form during the furnace-cooling process. Lamellar phases, which exhibit lower thermostability compared with the thin-platelet LPSO, slightly improve the tensile yield strength and induce numerous cracks which result in the premature fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Toucan: A performance portable, scalable implementation of the DECA algorithm

In the field of additive manufacturing (AM), cellular automata (CA) is extensively used to simulate microstructural evolution during solidification. However, while traditional CA approaches are relatively fast, they still require a substantial number of time steps, are limited to moderate volumes, and are relatively difficult to improve through parallelism due to the highly localized nature of the solidification front. Here, to address these issues of time to solution and load balancing, we introduce Toucan, a parallel, performance-portable, and scalable code written in C++ with the Kokkos library that leverages the discrete event inspired cellular automata (DECA) algorithm to perform parallel-in-time (PinT) grain growth simulations. Toucan effectively mitigates load balancing issues by distributing the computational workload more evenly across processors, enhancing scalability and efficiency. We conduct both strong and weak scaling studies on up to 64 GPUs on the Frontier supercomputer, demonstrating that Toucan significantly outperforms the current state-of-the-art, time-stepped CA code, ExaCA, on both single and multi-GPU simulations. Even in AM-specific weak scaling scenarios, Toucan maintains near-ideal scaling, in contrast to the linear increase observed with ExaCA due to the moving laser raster pattern. This study highlights Toucan’s potential to transform microstructural simulations in AM by radically improving both efficiency and scalability over existing methods.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure-Based Understanding of High-Temperature Deformation Behaviors in Laser Powder Bed Fusion (LPBF) 316H Stainless Steel

This report presents the results of high-temperature mechanical property testing and microstructural analysis of laser powder bed fusion (LPBF) 316H stainless steel (SS) conducted during Fiscal Year 2025 (FY25) under the U.S. Department of Energy, Office of Nuclear Energy’s Advanced Materials and Manufacturing Technologies (AMMT) program. The study builds upon prior work by expanding the mechanical property test matrix and advancing a microstructure-based mechanistic understanding of LPBF 316H SS performance, with a focus on the solution annealed (SA, 1100°C for 1 hour) materials. High-temperature tension, creep, fatigue, and creep-fatigue tests were performed. Thermal aging studies were conducted. Advanced characterization techniques, including scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), and high-energy synchrotron X-ray diffraction, were employed to investigate the microstructural evolution during thermal aging and mechanical testing. It was discovered that the as-built (AB) LPBF 316H SS exhibited precipitation kinetics during thermal aging that are 10–100 times faster than its wrought counterpart due to the presence of high densities of preferred nucleation sites, while the precipitation kinetics in SA LPBF 316H was under investigation. The accelerated precipitation of embrittling phases such as sigma phase in LPBF 316H SS compared to its wrought counterpart led to significant impacts on creep ductility. The influence of laser printing parameters and build orientations on fatigue and creep-fatigue performance was observed. In assessing the creep-fatigue performance, it was discovered that the SA LPBF 316H samples failed in less than 200 cycles under 595°C, 0.5% (strain amplitude) with a 60-minute hold time. This work establishes a mechanistic framework for predicting the long-term behavior of LPBF 316H SS, supporting its rapid qualification under the ASME BPVC. The findings contribute to the broader goal of enabling the deployment of advanced materials in next-generation nuclear energy systems. An outlook for FY26 work, including continued aging studies, mechanical testing, and microstructural characterization, is provided.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural features and deuterium diffusion in lithium penta-aluminate pellets under He + and D + ion irradiation

Lithium (Li) penta-aluminate (LiAl 5 O 8 ) is investigated as a potential tritium (T) breeding material, with a focus on microstructural response to ion irradiation and deuterium (D) diffusion behavior. Under high-fluence ion irradiation (2 x 10 17 (He + +D + )/cm 2 ) at 773 K, LiAl 5 O 8 exhibits significant disorder on the Li sublattice, as revealed by atomic-resolution scanning transmission electron microscopy, while the Al and O sublattices remain stable, demonstrating strong resistance to structural amorphization. Irradiation induces the formation of platelet-shaped antiphase boundaries (APBs), which may serve as effective D trapping sites. Atom probe tomography suggests the presence of 6 LiD clusters in the mass spectra, though definite conclusions regarding APB composition are hindered by signal overlap and limited data statistics. Time-of-flight secondary ion mass spectrometry reveals that D retention approaches to saturation at 3 x 10 17 (He + +D + )/cm 2 . Isothermal and isochronal annealing studies determine an average diffusivity of 1.6 x 10 -13 at 773 K and an effective activation energy of 0.8 ± 0.1 eV for D migration. Compared to γ-LiAlO 2 , LiAl 5 O 8 demonstrates superior irradiation resistance, minimal Li loss, and enhanced D retention, underscoring its potential as a durable breeder material for T production. In conclusion, these findings provide key insights into the microstructural evolution, defect dynamics, and D retention mechanisms in LiAl 5 O 8 under reactor-relevant conditions.

42 ENGINEERING↗
DOE OSTI2018

Effect of Ti Addition on the Microstructure and Mechanical Properties of Weld Metals in HSLA Steels

Acicular ferrite (AF) can significantly improve the mechanical properties of steel welds. One practical approach to enhance the formation of AF is to provide the heterogonous nucleation sites such as Ti oxides. In this study, Ti was added to different conventional welding processes including shield metal arc welding (SMAW), submerged arc welding (SAW) and tandem SAW (T-SAW). In the SMAW process, TiO{sub 2} particles as a source of Ti were inserted into the weld groove, while in the SAW and the T-SAW processes, the Ti-enriched S2MoTB wire was used as the filler metal. The microstructural evolution of weldments was characterized by employing optical and scanning electron microscopes. In addition, microhardness (Vickers, HV), Charpy impact and tensile tests were carried out to investigate the mechanical properties of weldments. Although the microhardness measurements of all weldments did not vary significantly and were in the range of 205-252 HV, there was a considerable difference in tensile and impact properties of the SAW and the T-SAW weldments. In the SMAW process, the addition of TiO{sub 2} results in no significant enhancement in tensile and impact toughness. This can be attributed to the inhomogeneous distribution of TiO{sub 2} particles as well as the formation of large inclusions in the structure. On the other hand, Ti addition to WM increased the yield strength from 489 to 552 MPa for the SAW process, and in contrast, it decreased the impact toughness from 75 to 33 J. This detrimental effect can be related to the higher deposition of other alloying elements in the WM and the formation of more ferrite side plate phase. By applying the T-SAW process, more Ti in WM led to a higher content of AF in the microstructure and increased both yield strength and impact toughness from 528 to 595 MPa and 100 to 180 J, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evidence of lithium mobility under neutron irradiation

Understanding the evolution of intermetallic materials in high-radiation environments is of great importance for fusion science and national security. Tritium ( 3 H) and lithium ( 6 Li, 7 Li) transport within neutron irradiated claddings coated with aluminide (FeAl3) has been investigated using state-of-the-art multimodal imaging. Specifically, scanning electron microscopy – focused ion beam (SEM-FIB) was used to prepare irradiated coating lift-out samples for follow-on microanalysis. Here, scanning transmission electron microscopy (STEM) was used to acquire atomic-scale information on the carbonaceous structure and elemental mapping. Atomic force microscopy (AFM) was used to determine lift-out dimensions nondestructively. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) spectral and depth profiling show unexpected lithium isotopic distributions in the irradiated cladding, raising an important evidence of possible light isotope mobility within the cladding under elevated temperature and irradiation. ToF-SIMS three-dimensional chemical mappings of mid- and bottom-cladding coatings show light isotopic (e.g., 3 H, 6 Li, 7 Li) distributions in the irradiated coating and give new insights into the fundamental mechanism related to transport mechanisms within the cladding. Multimodal imaging is power to link microstructure, chemistry, and nanoscale defects that impact reliability of these materials. Furthermore, chemical mapping offers observations of the microstructural evolution due to irradiation and provides insights into unexpected material transport under extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Low and room temperatures tensile properties of a nanoprecipitate-strengthened (FeCoCr)40Ni40Al10Cu10 high-entropy alloy

Highlights: • We designed a (FeCoCr){sub 40}Ni{sub 40}Al{sub 10}Cu{sub 10} high entropy alloy (HEA) strengthened by exclusive L1{sub 2} nano-precipitates. • The present HEA exhibited excellent combination of tensile strength (~1200MPa) and elongation (~36%) at 233 K. • The coherent nano-precipitates, deformation twinning and immobile LC locks made a joint contribution to the optimal mechanical property. - Abstract: We report the tensile properties and microstructural evolution of a high entropy alloy (FeCoCr){sub 40}Ni{sub 40}Al{sub 10}Cu{sub 10} deformed at low temperature (233K) and room temperature (293 K). The alloy presented a superior combination of tensile strength (~1200 MPa) and elongation (~36%) at 233 K than at 293 K. Transmission electron microscopy revealed that the enhanced tensile properties at low temperature were due to deformation twinning, the formation of immobile Lomer-Cottrell dislocation locks, and the high density coherent nano-precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Friction stir welding of multi-walled carbon nanotubes reinforced Al matrix composites

Highlights: • Al/MWCNT composites were successfully welded using friction stir welding. • After FSW, the composites possessed an excellent balance of mechanical properties. • High tensile strength and elongation over BM owing to MWCNTs after FSW. • Microstructures were investigated according to MWCNT contents and FSW conditions. - Abstract: In this study, we prepared composites between Al and multi-walled carbon nanotubes (MWCNTs) using the friction stir welding (FSW) method and investigated their microstructural evolution and mechanical properties by controlling the amount of MWCNT (1 and 3 vol%) and the plunging load (400 and 600 kg) used. After the FSW process, MWCNT showed slight coarsening of grain with random shear textures and accumulated dislocations; the differences obtained by varying the plunging load and MWCNT amount were insignificant. The friction-stir welded composite obtained using 3 vol% MWCNT and a plunging load of 600 kg possessed two-times better balance between strength and ductility than the base metal, due to the presence of both MWCNTs and the partially decomposed Al{sub 4}C{sub 3} in the composite.

36 MATERIALS SCIENCE↗