Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Solid solutions limited by grain-boundary solute clustering in ultrafine-grained alloys

Immiscible Ag-Cu alloys exhibit complex behavior due to varying Cu solid solubilities reported under equilibrium and metastable conditions. In ultrafine-grained alloys, these limits are further complicated by a high fraction of grain boundaries, where solute atoms tend to segregate and, in some cases, form clusters. Here, this study investigates the influence of Cu solute segregation and clustering on solid-solution limits in ultrafine-grained Ag-Cu alloys synthesized by magnetron sputtering with varying Cu content. X-ray diffraction peak shifts reveal a solid-solution concentration plateau for Cu contents from 4.9 to 11.7 at %, in contrast to the peak shifts predicted by density-functional theory for Ag-Cu alloys. Scanning transmission electron microscopy further reveals limited solid solubility and the formation of numerous Cu-rich clusters at grain boundaries. Atomistic simulations demonstrate that such limited solubility does not arise from grain boundary segregation alone, but only when strong solute-solute interactions promote the formation of grain-boundary Cu solute clusters.

Density-functional theory↗

Pseudo capacitive performance of copper oxide thin films grown by RF sputtering

Thin films of Copper Oxide were prepared by radio frequency magnetron sputtering on steel substrates maintained at 250°C under different RF powers ranging from 150W to 250W by keeping the sputtering pressure at 5.7×10{sup −3} mbar and O{sub 2}:Ar ratio of 1:7. The influence of RF power on the pseudo capacitive performance of thin films was studied. The X-ray diffraction studies and Raman studies indicates that all the thin films exhibits CuO phase. The electrochemical studies was done by using three electrode configuration with platinum as reference electrode. From the cyclic voltammetry studies a high rate pseudocapacitance of 227 mFcm{sup −2} at 0.5 mVs{sup −1} and 77% of capacity retention after 1000 cycles was obtained for the CuO thin films prepared at an RF power of 220W.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Thickness on the Structure, Composition and Properties of Titanium Nitride Nano-Coatings

Titanium nitride (TiNx) coatings were grown by magnetron sputtering onto Si(1 0 0) substrates by varying time of deposition to produce coatings with variable thickness (dTiN) in the range of 20-120 nm. TiNx coatings were characterized by studying their structure, composition, and mechanical properties. Nuclear reaction analysis (NRA) combined with Rutherford backscattering spectrometry (RBS) analyses indicate that the grown coatings were stoichiometric TiN. Grazing incidence X-ray diffraction (GIXRD) measurements indicate that the texturing of TiN coatings changes as a function of dTiN. The (1 1 1) and (0 0 2) peaks appear initially; (1 1 1) becomes intense while (0 0 2) disappears with increasing dTiN. Dense, columnar grain structure was evident for all the coatings in electron microscopy analyses. The residual stress for TiN coatings with dTiN~120 nm was 1.07 GPa in compression while thinner samples exhibit higher values of stress.

Coatings↗

A transmission electron microscopy study of the deformation behavior underneath nanoindents in nano-scale Al-TiN multilayered composites

Nano-scale multilayered Al-TiN composites were deposited with DC magnetron sputtering technique in two different layer thickness ratios - Al:TiN = 1:1 and Al:TiN = 9:1. The Al layer thickness varied from 2 nm to 450 nm. The hardness of the samples was tested by nanoindentation using a Berkovich tip. Cross-sectional Transmission Electron Microscopy (TEM) was carried out on samples extracted with Focused Ion Beam (FIB) from below the nanoindents. This paper presents the results of the hardness tests in the Al-TiN multilayers with the two different thickness ratios and the observations from the cross-sectional TEM studies of the regions underneath the indents. These studies showed remarkable strength in the multilayers, as well as some very interesting deformation behavior in the TiN layers at extremely small length scales, where the hard TiN layers undergo co-deformation with the Al layers.

36 MATERIALS SCIENCE↗

Soft Landing of Bare Nanoparticles with Controlled Size, Composition, and Morphology

A kinetically-limited physical synthesis method based on magnetron sputtering and gas aggregation has been coupled with size-selection and ion soft landing to prepare bare metal nanoparticles on surfaces with controlled coverage, size, composition, and morphology. Employing atomic force microscopy (AFM) and scanning electron microscopy (SEM), it is demonstrated that the size and coverage of bare nanoparticles soft landed onto flat glassy carbon and silicon as well as stepped graphite surfaces may be controlled through size-selection with a quadrupole mass filter and the length of deposition, respectively. The bare nanoparticles are observed with AFM to bind randomly to the flat glassy carbon surface when soft landed at relatively low coverage (1012 ions). In contrast, on stepped graphite surfaces at intermediate coverage (1013 ions) the soft landed nanoparticles are shown to bind preferentially along step edges forming extended linear chains of particles. At the highest coverage (5 x 1013 ions) examined in this study the nanoparticles are demonstrated with both AFM and SEM to form a continuous film on flat glassy carbon and silicon surfaces. On a graphite surface with defects, however, it is shown with SEM that the presence of localized surface imperfections results in agglomeration of nanoparticles onto these features and the formation of neighboring depletion zones that are devoid of particles. Employing high resolution scanning transmission electron microscopy in the high angular annular dark field imaging mode (STEM-HAADF) and electron energy loss spectroscopy (EELS) it is demonstrated that the magnetron sputtering/gas aggregation synthesis technique produces single metal particles with controlled morphology as well as bimetallic alloy nanoparticles with clearly defined core-shell structure. Therefore, this kinetically-limited physical synthesis technique, when combined with ion soft landing, is a versatile complementary method for preparing a wide range of bare supported nanoparticles with selected properties that are free of the solvent, organic capping agents, and residual reactants present with nanoparticles synthesized in solution.

cluster↗

The effects of tungsten concentration on crystalline structure and perpendicular magnetic anisotropy of Co-W films

In this study, Co-W thin films deposited by DC magnetron sputtering were demonstrated to be perpendicular magnetic anisotropic with large magnetocrystalline anisotropy energy (MAE). Thermodynamic calculations based on Miedema’s semi-empirical model have been used to estimate the phase in this binary alloy system. Based on the thermodynamic calculations results, a series of Co-W thin films were deposited on amorphous Ta underlayer with different tungsten concentrations. According to the X-ray diffraction results, the crystal structure of Co-W thin films is consistent well with that of thermodynamic calculations. Large MAE of Co-W thin films can be obtained with K{sub u} over 2.1 × 10{sup 5} J/m{sup 3} after vacuum annealing. The perpendicular coercivity (H{sub c}) of Co-W thin film reaches 9.1 × 10{sup 4} A/m. Therefore, the Co-W thin film is considered as a potential choice of high-density magnetic recording media materials.

36 MATERIALS SCIENCE↗

Characterization of Ti{sub 1-x}Al{sub x}N coatings with selective IR reflectivity

Ti{sub 1-x}Al{sub x}N thin films were deposited by reactive magnetron sputtering. The obtained different stoichiometries give rise to different optical properties as the films change from metallic to dielectric. In this work the IR reflectivity of these coatings is investigated taking into account different application fields for IR selective Ti{sub 1-x}Al{sub x}N thin films. Low Al content coatings present high reflectivity, high absorptance and low thermal emittance. High Al compositions give raise to coatings with high absorptance and high thermal emittance. The composition of the coatings was evaluated combining electron energy loss spectroscopy (EELS) and energy dispersive spectroscopy. Scanning electron microscopy (SEM) revealed a columnar structure. Reflectance spectra for the visible and infrared spectral ranges were used to obtain the solar absorptance and thermal emittance values, used to calculate the equilibrium temperature of the coatings. The thermal stability in air from 300 to 600 C was also evaluated. (author)

14 SOLAR ENERGY↗

A pathway to synthesizing single-crystal Fe and FeCr films

Nuclear reactor environments provide a unique scientific and engineering challenge wherein materials must tolerate prolonged exposure to concurrent irradiation, elevated temperatures, and corrosive media. However, uncontrolled variability in material composition and structure often prohibits truly single-variable experiments that can reveal basic aspects of environmental damage. Here, Magnetron sputtering is used to provide a more controlled model system for these fundamental studies, yielding reproducible single-crystal Fe and FeCr thin films containing 8 and 18 at.% Cr. Electron microscopy is used to determine the systematic correlations between growth conditions and the resulting film microstructure and surface morphology. It is found that the substrate temperature and applied radio frequency (RF) bias can be tuned to obtain consistent homogeneous and single crystal films with a minimal amount of Ar impurities from the RF bias process. Epitaxial, single-crystal Fe films are obtained on MgO substrates at 500 °C with 10 Watt (W) RF bias deposition. However, when Cr is alloyed with Fe, higher substrate temperatures (600 °C) and applied RF biases (15 W) are required to achieve a similar epitaxial single-crystal FeCr film. Accelerated molecular dynamics simulations reveal that Cr impedes surface transport, explaining the need for higher temperature and bias during the growth of the Cr-bearing films.

36 MATERIALS SCIENCE↗

Ultrathin Ruthenium Films on Graphene Buffered SiO 2 via Quasi Van der Waals Epitaxy

In this study, we demonstrate a quasi van der Waals epitaxy approach to prepare single crystalline Ru ultrathin film on large scale, monolayer graphene. Physical and epitaxial properties of bulk, near surface and surface of ultrathin Ru films were comprehensively studied using various structural, morphological, compositional, and electrical characterization techniques. Here, we confirm that Ru can epitaxially grow on single, monolayer graphene using magnetron sputtering at elevated temperature of 600 °C. The epitaxial Ru films with film thickness ranging from 94.2 nm down to 3.9 nm show the (0001) out-of-plane orientation. The epitaxial relationships between Ru and graphene are out-of-plane Ru(0001) || graphene(0001) and in-plane Ru[$11\bar20$] || graphene[$11\bar20$]. All the Ru films show smooth surfaces with root-mean-square roughness less than 0.8 nm and have negligible oxide layer on the surfaces. The Ru films on graphene demonstrate significantly reduced electrical resistivity comparing to their counterpart grown on bare SiO 2 , which show polycrystalline nature. For 7.1 to 3.9 nm film thicknesses, the resistivity of Ru on graphene shows 38 to 45% resistivity decrease from that of Ru film on bare SiO 2 without graphene. Our observations suggest the existence of the above-classical van der Waals interaction between Ru and graphene. On the other hand, graphene is capable of effectively blocking the inter-diffusion/interaction between Ru and SiO 2 during a 1000 °C annealing process.

36 MATERIALS SCIENCE↗

Perspectives on novel refractory amorphous high-entropy alloys in extreme environments

Two new refractory amorphous high-entropy alloys (RAHEAs) within the W–Ta–Cr–V and W–Ta–Cr–V–Hf systems were herein synthesized using magnetron-sputtering and tested under high-temperature annealing and displacing irradiation using in situ Transmission Electron Microscopy. While the 14W-41Ta-26Cr-19V in at.% RAHEA (defined as WTaCrV RAHEA) was found to be unstable under such tests, additions of Hf in this system composing a new quinary 24W-40Ta-18Cr-5V-13Hf in at.% RAHEA (defined as WTaCrVHf RAHEA) was found to be a route to achieve stability both under annealing and irradiation. A new effect of nanoprecipitate reassembling observed to take place within the WTaCrVHf RAHEA under irradiation indicates that a duplex microstructure composed of an amorphous matrix with crystalline nanometer-sized precipitates enhances the radiation response of the system. Further, it is demonstrated that tunable chemical complexity arises as a new alloy design strategy to foster the use of novel RAHEAs within extreme environments. New perspectives for the alloy design and application of chemically-complex amorphous metallic alloys in extreme environments are presented with focus on their thermodynamic phase stability when subjected to high-temperature annealing and displacing irradiation.

36 MATERIALS SCIENCE↗

Improving electrical performance and bias stability of HfInZnO-TFT with optimizing the channel thickness

RF magnetron sputtered HfInZnO film and atomic layer deposition (ALD) Al{sub 2}O{sub 3} film were employed for thin film transistors (TFTs) as channel layer and gate insulator, respectively. To achieve HfInZnO-TFT with high performance and good bias stability, the thickness of HfInZnO active layer was optimized. The performance of HfInZnO-TFTs was found to be thickness dependent. As the HfInZnO active layer got thicker, the leakage current greatly increased from 1.73 × 10{sup −12} to 2.54 × 10{sup −8} A, the threshold voltage decreased from 7.4 to −4.7 V, while the subthreshold swing varied from 0.41 to 1.07 V/decade. Overall, the HfInZnO film showed superior performance, such as saturation mobility of 6.4 cm{sup 2}/V s, threshold voltage of 4.2 V, subthreshold swing of 0.43 V/decade, on/off current ratio of 3 × 10{sup 7} and V{sub th} shift of 3.6 V under V{sub GS}= 10 V for 7200 s. The results demonstrate the possibility of fabricating TFTs using HfInZnO film as active layer and using ALD Al{sub 2}O{sub 3} as gate insulator.

36 MATERIALS SCIENCE↗

Ferroelectrics everywhere: Ferroelectricity in magnesium substituted zinc oxide thin films

We demonstrate ferroelectricity in Mg-substituted ZnO thin films with the wurtzite structure. Zn 1–x Mg x O films are grown by dual-cathode reactive magnetron sputtering on (111)-Pt // (0001)-Al 2 O 3 substrates at temperatures ranging from 26 to 200 °C for compositions spanning from x = 0 to x = 0.37. X-ray diffraction indicates a decrease in the c-lattice parameter and an increase in the a-lattice parameter with increasing Mg content, resulting in a nearly constant c/a axial ratio of 1.595 over this composition range. Transmission electron microscopy studies show abrupt interfaces between Zn 1–x Mg x O films and the Pt electrode. When prepared at pO 2 = 0.025, film surfaces are populated by abnormally oriented grains as measured by atomic force microscopy for Mg concentrations >29%. Raising pO 2 to 0.25 eliminates the misoriented grains. Optical measurements show increasing bandgap values with increasing Mg content. When prepared on a 200 °C substrate, films display ferroelectric switching with remanent polarizations exceeding 100 μC cm –2 and coercive fields below 3 MVcm –1 when the Mg content is between ~30% and ~7%. Substrate temperature can be lowered to ambient conditions, and when doing so, capacitor stacks show only minor sacrifices to crystal orientation and nearly identical remanent polarization values; however, coercive fields drop below 2 MV/cm. Using ambient temperature deposition, we demonstrate ferroelectric capacitor stacks integrated directly with polymer substrate surfaces.

36 MATERIALS SCIENCE↗

Growth and structure of alpha-Ta films for quantum circuit integration

Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.

42 ENGINEERING↗

Topochemical Synthesis and Electronic Structure of High-Crystallinity Infinite-Layer Nickelates on an Orthorhombic Substrate

Superconductivity in infinite-layer nickelates has stirred much research interest, to which questions regarding the nature of superconductivity remain elusive. A critical leap forward to address these intricate questions is through the growth of high-crystallinity infinite-layer nickelates, including the “parent” phase. Here, we report the synthesis of a high-quality thin-film nickelate, NdNiO 2 . This is achieved through the growth of a perovskite precursor phase (NdNiO 3 ) of superior crystallinity on the NdGaO 3 substrate by off-axis RF magnetron sputtering and a low-temperature topochemical reduction using NaH. We observe a nonlinear Hall effect at low temperatures in this “non-doped” phase. We further study the electronic properties using advanced X-ray scattering and first-principles calculations. We observe spectroscopic indications of the enhanced two-dimensionality and a reduced hybridization of Nd 5d and Ni 3d orbitals. These findings unlock new pathways for preparing high-quality infinite-layer nickelates and provide new insights into the intrinsic features of these compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ferroelectricity of wurtzite Al 1−x Hf x N heterovalent alloys

Thin films of aluminum hafnium nitride (Al1−xHfxN) were synthesized via reactive magnetron sputtering for Hf contents up to x = 0.13. X-ray diffraction showed a single c-axis oriented wurtzite phase for all films. Hard x-ray photoelectron spectroscopy demonstrated homogeneous Al:Hf distribution through the thin films and confirmed their insulating character. A collection of complementary tests showed unambiguous polarization inversion, and thus ferroelectricity in multiple samples. Current density vs electric field hysteresis measurements showed distinct ferroelectric switching current peaks, the piezoelectric coefficient d 33,f,meas measured using a double beam laser interferometer (DBLI) showed a reversal in sign with similar magnitude, and anisotropic wet etching confirmed field-induced polarization inversion. This demonstrates the possibility of using tetravalent–and not just trivalent–alloying elements to enable ferroelectricity in AlN-based thin films, highlighting the compositional flexibility of ferroelectricity in wurtzites and greatly expanding the chemistries that can be considered for future devices.

36 MATERIALS SCIENCE↗

Resonant surface enhancement of Raman scattering of Ag nanoparticles on silicon substrates fabricated by dc sputtering

Ag nanoparticles (AgNPs) were deposited onto silicon substrates by direct current (dc) magnetron sputtering. The influences of sputtering power and sputtering time on the AgNP film morphology were studied using atomic force microscopy. The particle size was successfully tuned from 19 nm to 53 nm by varying the sputtering time at a dc power of 10 W. When Rhodamine 6 G (R6G) was used as the probe molecule, the AgNP films showed significant surface enhanced Raman scattering effect. In particular, it is found that larger particles show stronger enhancement for lower concentrations of R6G while smaller particles display stronger enhancement for higher concentrations of R6G.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermal conductivity of sputtered amorphous Ge films

We measured the thermal conductivity of amorphous Ge films prepared by magnetron sputtering. The thermal conductivity was significantly higher than the value predicted by the minimum thermal conductivity model and increased with deposition temperature. We found that variations in sound velocity and Ge film density were not the main factors in the high thermal conductivity. Fast Fourier transform patterns of transmission electron micrographs revealed that short-range order in the Ge films was responsible for their high thermal conductivity. The results provide experimental evidences to understand the underlying nature of the variation of phonon mean free path in amorphous solids.

36 MATERIALS SCIENCE↗

Unexpected short- and medium-range atomic structure of sputtered amorphous silicon upon thermal annealing

We investigate the structure of magnetron-sputtered (MS) amorphous silicon (a-Si) prepared under standard deposition conditions and compare this to pure ion-implanted (II) a-Si. The structure of both films is characterized in their as-prepared and thermally annealed states. Significant differences are observed in short- and medium-range order following thermal annealing. Whereas II a-Si undergoes structural relaxation toward a continuous random network, MS a-Si exhibits little change. Cross-sectional transmission electron microscopy reveals the presence of nanopores in the MS film consistent with reduced mass-density. Therefore, the short- and medium-range order of annealed, MS a-Si is tentatively attributed to these pores.

36 MATERIALS SCIENCE↗