Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Level density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Dependence of divertor turbulence on plasma density and current in TCV

To reliably predict the distribution of heat and particle fluxes at the target plates of tokamaks, a comprehensive understanding of turbulence throughout the entire Scrape-Off-Layer (SOL) is imperative. This study examines divertor turbulence systematically across a broad parameter range on the TCV tokamak, including variations in magnetic field direction, plasma current I p ∈ [140,320] kA, edge safety factor q 95 ∈ [2.6,4.7] and Greenwald fraction f G ∈ [0.18,0.6]. The TCV X-point Gas Puff Imaging (GPI) system is used to measure 2D filament properties in the inner and outer divertor region. The fluctuation levels in the divertor are found to strongly increase with density (to 80% over most of the SOL) while remaining insensitive to I p . The previously identified divertor-localized filaments (DLF), located on the bad curvature side of the outer divertor leg, are found to be a common feature on TCV, while no filaments are observed in the PFR. DLFs are present over most of the parameter space and in both field directions. However, they are absent, or appear only closer to the target, for sufficiently large Λ div ≳ 10 or q 95 ≳ 3.7. Across both I p and f G scans, some clear trends with Λ div are found for divertor filament sizes and velocities, and with target fall-off lengths of density and heat flux profiles at the outer target. This study provides important experimental insights to turbulent transport in the divertor also for comparison with self-consistent, turbulence simulations and extrapolation to future reactor conditions.

cross-field transport↗
DOE OSTI2024

Rapid recovery of invasive wild pig (Sus scrofa) populations following density reduction

Abstract Trapping is an effective strategy for control of invasive wild pig (Sus scrofa), but eradication of populations via trapping alone typically is impractical throughout much of the species’ introduced range. Consequently, recovery of wild pig populations to pre-trapping levels following control is a major impediment to success of long-term control. In this study, we conducted camera-trap surveys to monitor recovery of two wild pig populations immediately following density reductions achieved via trapping on two sites on the Savannah River Site, SC. We used spatial capture-recapture models to estimate wild pig density during seven 3 week periods spanning 12 months to: (1) determine the time required for populations to recover to pre-trapping levels; and (2) evaluate trends in population growth, density, and distribution during recovery. Recovery of both wild pig populations started immediately after trapping ceased, with populations reaching pre-trapping levels in 3 and 5 months. Threeweek population growth rates for each wild pig population during recovery averaged 1.28 (range = 1.11–1.39 on site 1) and 1.24 (range = 0.64–1.92 on site 2), which corresponded to a 345% and 132% increase in abundance (an increase of 141 and 126 individual wild pigs on site 1 and 2, respectively) of each population by the last survey period. Rapid recovery and growth beyond pre-trapping levels of wild pig populations likely were driven by residual wild pigs not removed by trapping and compensatory reproduction and immigration. Our study is one of the first to provide information on how quickly wild pig populations can recover following overall density reductions of 54–68% and indicates practitioners should be prepared to reinitiate trapping efforts in as little as 3 months to prevent recovery of wild pig populations following control.

Biodiversity & Conservation↗
DOE OSTI2025

Datasets for Custom-trained Machine-learning Interatomic Potentials: Nitric Acid Aqueous Solution

This dataset was generated using an iterative active learning strategy with the ArcaNN software package (https://github.com/arcann-chem/arcann_training) to train machine-learning interatomic potentials (MLIPs) for aqueous nitric acid. Each active-learning cycle consisted of three stages: (1) training, (2) exploration, and (3) labeling. The initial training set comprised approximately 800 randomly selected configurations from a previous study by Lewis et al. (https://doi.org/10.1021/jp205510q), which investigated nitric acid solutions at 2, 3, 4, and 5 mol/L. For all configurations, single-point calculations of atomic forces and total energies were performed at the quantum density functional theory BLYP-D2 and PBE-D3 levels of theory using the CP2K Quickstep module. Valence electrons were treated explicitly, while core electrons on all atoms were represented by norm-conserving Goedecker–Teter–Hutter (GTH) pseudopotentials. Long-range dispersion interactions were accounted for using Grimme dispersion corrections. Wave functions were expanded in a mixed Gaussian-and-plane-wave scheme using TZV2P-MOLOPT basis sets for all elements and an 800 Ry auxiliary plane-wave cutoff for the electron density. Self-consistent field convergence was accelerated using orbital transformation and Direct Inversion in the Iterative Subspace, with a convergence threshold of 10^{-6}. All single-point calculations were carried out in periodic orthorhombic cells whose dimensions match those of the molecular configurations sampled from earlier trajectories. The CELL_REF keyword in CP2K was used to define a fixed reference cell, ensuring consistency in the reference data used for MLIP training, particularly when cell fluctuations are present in NpT simulations. The resulting high-fidelity energies and forces constitute the ground-truth labels used to train the MLIPs contained in this dataset.

Dinpajooh, Mohammadhasan [Pacific Northwest Nation↗
DOE OSTI2021

CHARGED POINT DEFECTS AND DEFECT COMPLEXES IN PHOSPHORENE AND STRUCTURAL PREDICTION OF TAU-11, A DENSITY FUNCTIONAL THEORY APPROACH

With the advent of powerful computers, first principle calculations have become a robust and reliable tool to complement experiments in the study of materials. First principle calculations such as density functional theory can be used to guide experiments to save time and effort when it comes to new and advanced materials discovery. Study of charge defects in materials and crystal structure prediction are such areas in which density functional theory calculations facilitate the prediction of defect formation energy, charge transition levels and elemental site occupations. Experimentally, studying charge defects requires inferring results from various techniques. Likewise, determining site occupancies for similar elements using experimental techniques is challenging and sometimes impossible. In this work, we study the charged intrinsic and extrinsic defects and defect complexes in phosphorene and determine the site occupancies of Al, Fe and Si in the τ11 phase using density functional theory. In the defect work, we calculate the defect formation energy, charge transition level, binding energies and Stokes shift for vacancy, dopant substitution and dopant-vacancy defect complexes in phosphorene. We found that vacancy defect in phosphorene becomes negatively charged in n-type doping and may passivate the dopants and reduce carrier concentration and mobility. For non-metal dopants in phosphorene, we predict that O, S and Si prefer to form dopant-vacancy complexes removing the vacancy defect states from the band gap. Mn dopant-vacancy defect complex exhibits possibility of switching between two magnetic spin states. Lastly, using density functional theory, we complement the results from neutron powder diffraction to determine the site occupancies of Al and Si in τ11 phase which was used to determine the alloying element to develop a high temperature and low density alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Overcoming the Damping–Elasticity Paradox via 3D‐Printed NiTiSn Nanocomposite

Abstract Developing high damping alloys (HDAs) with large elastic strain has attracted growing attention due to the increasing demand for energy absorption with overload reliability and reusability. However, damping capacity inherently conflicts with elasticity, because the former requires a liable movement of crystal defects while the latter opposite. To deal with the damping‐elasticity paradox, the advantage of pseudobinary eutectic reaction and rapid cooling of laser powder bed fusion is taken to fabricate a bulk NiTiSn nanocomposite with a two‐level hierarchical structure. The first‐level architecture is composed of martensitic NiTi nanolamellae and reinforced Ti 3 Sn nanolamellae. In addition to lattice strain matching and lamellar boundary strengthening, a novel mechanism of martensite reorientation mediated by reversible stress‐induced detwinning‐twinning is activated to generate large elastic strain. A high density of nanotwins and nanodomains within NiTi nanolamellae constitute the second‐level architecture, which provides pronounced internal friction for high damping capacity. As a result, our NiTiSn nanocomposite exhibits a record‐high integration of damping capacity (tanδ > 0.10) and elastic strain (exceeding 4.5%), as well as superb stability under cyclic overload. This research not only represents a major breakthrough in achieving HDAs with outstanding damping and elastic strain but also offers a novel paradigm for high‐performance functional and structural materials.

Chemistry↗
DOE OSTI2020

Residential Building Energy Efficiency Field Studies: Low-Rise Multifamily

In recent years, the U.S. Department of Energy (DOE) has conducted a series of research studies to validate energy efficient building technologies in the field. Much of the work has focused on single-family construction, and some has also addressed commercial energy codes. The work detailed in this DOE-funded study (EE0007616) focuses on low-rise multifamily buildings (three stories or fewer above grade) in various regions of the United States, and reports on how state-level building codes are being implemented, both in terms of observed characteristics and also in terms of estimated energy impacts. Nearly 100 buildings across four states—Illinois, Minnesota, Oregon, and Washington—were sampled, which represent a range of climate types from mild temperature to very cold continental. Both common entry and outdoor entry buildings were included, and a parallel research project evaluated envelope air tightness and current still-evolving air tightness testing methods. Finally, a set of structured interviews of building designers and other relevant professionals was carried to out to gain more insight into this market. To the greatest extent possible, the methodology developed under the project for low-rise multifamily buildings mirrored the approach established by Pacific Northwest National Laboratory (PNNL) for single-family residential buildings (https://www.energy.gov/eere/buildings/downloads/residential-building-energy-code-field-study). This included the general approach to sampling, recruitment, and data collection, as well as data analysis and presentation. The range of permitting dates for the sites encompassed two energy code cycles in most regions. All states in the study had adopted a variation of the International Energy Conservation Code (IECC) for the structure of their state code. The low-rise multifamily occupancy presents a hybrid building type: most of the building’s conditioned floor area was covered by the residential chapter of the code while portions of the building (such as corridors and common spaces) fell under the commercial code chapter. The key items assessed in this work were: Building Shell—exterior wall insulation, ceiling insulation, foundation insulation, windows. Common Areas—HVAC and lighting. Living Units—lighting, ventilation. A few items were not assessed in detail, given their relative paucity in this occupancy type; these included duct leakage, pipe insulation, and hot water circulation controls. Building characteristics were collected via a combination of architectural, mechanical, electrical, and plumbing plan reviews and field inspections, and entered into a spreadsheet-based tool that was later queried to build a database. Data went through quality control both upon arrival and via a later semi-automated review and assurance process. Most of the data are presented graphically so that the reader can quickly assess compliance with the applicable energy codes (both by state and by code year). As a final step, EnergyPlus™ simulations were created for all buildings in the study to estimate both the as-found energy use intensity (EUI) and the energy and CO 2 that could be saved if features that were found to not meet code minimums were brought up to code. The savings estimates were tabulated for each of the four states in the study. The research team found that the single-family approach was largely applicable to low-rise multifamily buildings. This applies to both the data collection and the prototype EUI analysis. Most of the occupied space is living units and falls under residential energy codes, and many characteristics use similar envelope construction and relatively straightforward mechanical systems and lighting. One of the most challenging aspects of this work was to build an effective spreadsheet-based data collection instrument that could allow efficient collection of both building plan and field data. The research team is of the view that other methods could be equally effective if the work is done carefully with diligent quality control. The primary findings for the work center around the thermal envelope and mechanical systems and lighting at the sites: For thermal envelope components, the majority of buildings met or were better than the prescriptive code.This suggests that building designers and builders are aware of code requirements. In some cases, surveyed buildings were designed to qualify for energy efficiency certification programs. These buildings made up at least 20% of sampled buildings in each state. Almost all buildings met mechanical system efficiency requirements (for both living units and common areas). In some cases, sites employed systems that were considerably more efficient than required by the applicable energy code. Dwelling units had a majority of high-efficacy lighting, often in excess of the state’s residential code requirements. While high-efficacy fixtures were also typical in common areas (corridors and stairwells), lighting power densities (LPDs) in these areas were sometimes higher than levels dictated by the applicable part of the state commercial energy code. The simulation models run on a series of low-rise multifamily prototypes, informed by a composite of the field data collected, calculated annual EUIs of between 20 and 50 kBtu/ft2-yr, with the range representing the effects of both building characteristics and building location (climate zone). A detailed process (based on simulations of prototype buildings) was used to estimate the amount of avoided energy use that would occur if 100% adherence to energy codes were attained. The results indicated modest savings are attainable for items such as window thermal performance and common area lighting. The result is overall only a modest potential for additional energy savings, averaging about 10% of EUI.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Deformation, dislocation evolution and the non-Schmid effect in body-centered-cubic single- and polycrystal tantalum

A physically-informed continuum crystal plasticity model is presented to elucidate deformation mechanisms, dislocation evolution and the non-Schmid effect in body-centered-cubic (bcc) tantalum widely used as a key structural material for mechanical and thermal extremes. We show the unified structural modeling framework informed by mesoscopic dislocation dynamics simulations is capable of capturing salient features of the large inelastic behavior of tantalum at quasi-static (10 -3 s -1 ) to extreme strain rates (5000 s -1 ) and at low (77 K) to high temperatures (873 K) at both single- and polycrystal levels. Here we also present predictive capabilities of the model for microstructural evolution in the material. To this end, we investigate the effects of dislocation interactions on slip activities, instability and the non-Schmid behavior at the single crystal level. Furthermore, ex situ measurements on crystallographic texture evolution and dislocation density growth are carried out for polycrystal tantalum specimens at increasing strains. Numerical simulation results also support that the modeling framework is capable of capturing the main features of the polycrystal behavior over a wide range of strains, strain rates and temperatures. The theoretical, experimental and numerical results at both single- and polycrystal levels provide critical insight into the underlying physical pictures for micro- and macroscopic responses and their relations in this important class of refractory bcc materials undergoing large inelastic deformations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A conformal heat-drying direct ink writing 3D printing for high-performance lithium-ion batteries

High areal capacity electrodes hold great potential for high-energy density lithium-ion batteries (LIBs), but their poor electrochemical kinetics limit their power density. Here, in this study, high areal capacity 3D-structured LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathodes (4.3 mAh cm -2 ) are prepared via 3D printing with a manner of direct ink writing. The electrodes had an enlarged electrode–electrolyte contact area, shortened diffusion pathway, and reduced intercalation-induced stress, thereby delivering enhanced rate capability and cyclability in LIBs, which is 143.6 mAh g -1 at 3C and a 60.2 % capacity retention over 800 cycles at 1C. Moreover, at electrode level, the 3D-NMC exhibits an energy and power densities of 313.1 Wh kg -1 and 657.9 W kg -1 , respectively. Furthermore, the theoretical calculation suggests that reducing the gap width will be highly beneficial to the energy and power densities. This work establishes a milestone in understanding the cycling effect on the electrode local structure, including the void area and the LiNi 0.8 Mn 0.1 Co 0.1 O 2 region, which confirms the effectiveness of 3D printing for electrode preparation.

25 ENERGY STORAGE↗
DOE OSTI2022

Scanning tunneling microscopy and spectroscopy of NiTe 2

Nickel ditelluride is an unusual member of the transition metal dichalcogenide family which has garnered interest due to potential valley spin-polarized surface states near the Fermi level and the presence of Dirac nodes in its electronic band structure. In this work, exfoliation of bulk nickel ditelluride is performed under ultra-high vacuum in order to generate a clean surface for scanning tunneling microscopy and spectroscopy at 4.8 K. Multiple features in the observed electronic density of states are observed in the vicinity of the Fermi level and compared to calculated band structures to elucidate their origins. Finally, our results are consistent with the presence of the spin-polarized surface states, yet indicate trivial states, which are close to the Fermi level, can interfere with their potential utility in spintronic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Availability and reactivity of N 2 ( v ) for NH 3 synthesis by plasma catalysis

Production of vibrationally excited N 2 (N 2 (v)) in atmospheric pressure nonthermal plasma and loss of N 2 (v) by gas-phase reactions and reactions on catalytic surfaces are analyzed to examine the role of N 2 (v) in NH 3 formation by plasma catalysis. Vibrational state-to-state kinetic models complemented with molecular beam mass spectrometry (MBMS) measurements demonstrate that N 2 (v> 0) is produced with densities 100× greater than the density of N radicals by a radiofrequency atmospheric pressure plasma jet. The experimentally measured loss of N 2 (v) corresponds with a state-to-state kinetic model that describes loss of N 2 (v) by surface-mediated vibrational relaxation without consideration of reactions that convert N 2 (v) to NH 3 over the catalyst surface. Rate constants for vibrational relaxation of N 2 (v) on catalyst surfaces exceed upper bounds on proposed rate constants for NH 3 formation reactions from N 2 (v) over Fe when v < 9, Ni when v < 18, and Ag when v < 39, which indicates that only higher vibrational levels can possibly contribute to catalytic NH 3 formation faster than they undergo vibrational relaxation on the surface. Densities of N 2 (v> 8), vibrational levels that can possibly react over Fe to form NH 3 faster than they undergo vibrational relaxation, are less than or similar to N densities at the inlet of the catalyst bed and measured NH 3 formation for the investigated conditions in this work, while densities of N 2 (v> 17) and N 2 (v> 38) are orders of magnitude below the N density at the inlet of the catalyst bed and the measured NH 3 formation. The loss of N 2 (v) by vibrational relaxation on the surface limits the ability of N 2 (v) to contribute to catalytic NH 3 formation and explains why N 2 (v) does not produce NH 3 in quantities that are comparable to NH 3 formation from N even though N 2 (v > 0) is more abundantly produced by the plasma.

state-to-state kinetic modeling↗
DOE OSTI2023

Ballistic Ejection of Microdroplets from Overpacked Interfacial Assemblies

Spontaneous emulsification, resulting from the assembly and accumulation of surfactants at liquid–liquid interfaces, is an interfacial instability where microdroplets are generated and diffusively spread from the interface until complete emulsification. Here, it is shown that an external magnetic field can modulate the assembly of paramagnetic nanoparticle surfactants (NPSs) at liquid–liquid interfaces to trigger an oversaturation in the areal density of the NPSs at the interface, as evidenced by a marked reduction in the interfacial tension, γ, and corroborated with a magnetostatic continuum theory. Despite the significant reduction in γ, the presence of the magnetic field does not cause stable interfaces to become unstable. Upon rapid removal of the field, however, an explosive ejection of a plume of microdroplets from the surface occurs, a dynamical interfacial instability which is termed explosive emulsification. Further, this explosive event rapidly reduces the areal density of the NPSs to its pre-field level, stabilizing the interface. The ability to externally suppress or trigger the explosive emulsification and controlled generation of tens of thousands of microdroplets, uncovers an efficient energy storage and release process, that has potential applications for controlled and directed delivery of chemicals and remotely controlled soft microrobots, taking advantage of the ferromagnetic nature of the microdroplets.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tailoring the Electronic Structures and Spectral Properties of ZnO with Irradiation Defects Generated Under Intense Electronic Excitation: A Combined Experimental and DFT Approach

Here, the relationship between the composition of the internal defect states, spectral properties, and correlated electronic structures of wurtzite zinc oxide (ZnO) crystals under 645 MeV Xe 35+ irradiation is systematically investigated, employing experimental characterizations combined with first-principle calculations. Based on the ion irradiation-induced thermal expansion and relaxation processes, the high concentration of vacancy/interstitial defects produced from the transient disordered phase in molten track states trigger photoelectric changes, as follows: i) the generation of internal defect states effectively reduces the intrinsic bandgap (3.25 eV → 2.66 eV); ii) a large number of defective active sites inhibits the recombination between electron–hole pairs, causing dark conductance and photoconductance to increase with increasing damage levels until optimal fluence is achieved. Based on the density functional theory (DFT) with the GGA + U (GGA = generalized gradient approximation) method, the defective models associated with the different electronic structures, density of states, formation energy, and the nature of the chemical bonding are established. The narrowing of the bandgap observed experimentally and the enhancement of carrier concentration originating from the internal electron defect states are qualitatively verified, therefore laying the foundation for designing future nanoscale photoelectronic devices and microelectronics applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Shading contributes to Sphagnum decline in response to warming

Experimental warming of an ombrotrophic bog in northern Minnesota has caused a rapid decline in the productivity and areal cover of Sphagnum mosses, affecting whole-ecosystem carbon balance and biogeochemistry. Direct effects of elevated temperature and the attendant drying are most likely the primary cause of the effects on Sphagnum, but there may also be responses to the increased shading from shrubs, which increased with increasing temperature. To evaluate the independent effects of reduction in light availability and deposition of shrub litter on Sphagnum productivity, small plots with shrubs removed were laid out adjacent to the warming experiment on hummocks and hollows in three blocks and with five levels of shading. Four plots were covered with neutral density shade cloth to simulate shading from shrubs of 30%–90% reduction in light; one plot was left open. Growth of Sphagnum angustifolium/fallax and S. divinum declined linearly with increasing shade in hollows, but there was no response to shade on hummocks, where higher irradiance in the open plots may have been inhibitory. Shading caused etiolation of Sphagnum—they were thin and spindly under the deepest shade. A dense mat of shrub litter, corresponding to the amount of shrub litter produced in response to warming, did not inhibit Sphagnum growth or cause increases in potentially toxic base cations. CO 2 exchange and chlorophyll-a fluorescence of S. angustifolium/fallax from the 30% and 90% shade cloth plots were measured in the laboratory. Light response curves indicate that maximal light saturated photosynthesis was 42% greater for S. angustifolium/fallax grown under 30% shade cloth relative to plants grown under 90% shade cloth. The response of Sphagnum growth in response to increasing shade is consistent with the hypothesis that increased shade resulting from shrub expansion in response to experimental warming contributed to reduced Sphagnum growth.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Evaluation of mixed #3–7 plastic waste from material recovery facilities (MRFs) in the United States

Plastic recycling rates are still low in the United States (U.S.), with less than 10% of municipal solid waste (MSW) plastic being recycled. Most unrecycled plastics are identified by Resin Identification Codes (RIC) from #3–7, which are commonly destined for landfill or waste-to-energy facilities (WTE). Therefore, the composition and quality of outbound bales containing #3–7 plastics were assessed to understand the potential to increase recycling rates. Three bales were sourced from three different Material Recovery Facilities (MRFs) located in the United States. Each bale was manually sorted and characterized for quality and performance via multiple plastic characterization techniques. Considerable differences in bale composition were observed between MRFs, which correlated with the technology used by each MRF in the sorting process. The differences were substantial in the residual levels of poly(ethylene terephthalate) (PET) and high-density polyethylene (HDPE), which are highly desired for mechanical recycling processes and not expected in #3–7 plastics bales. Traditional recycling processes including washing, extrusion, and injection molding of the sorted material were employed prior to the physical, thermal, and molecular characterization. Despite differences in bale composition by plastic type, some polymer properties were similar across MRFs. Here, this research suggests that landfill-diverted mixed plastic waste can be utilized in the mechanical recycling of currently unrecycled materials, as processes can be designed to work with consistent polymer properties. It also highlights the need to upgrade the sorting systems to prevent waste feedstocks, which can be recycled with current technologies, from contaminating other plastic streams or reach landfills.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Physics-Informed Machine-Learning Prediction of Curie Temperatures and Its Promise for Guiding the Discovery of Functional Magnetic Materials

High-performance permanent magnets with a high Curie temperature, containing less critical materials, are integral to zero-carbon energy solutions. We built a machine-learning model trained over available experimentally measured Curie temperature values to predict the T C of multicomponent magnetic materials. We chose two compositions from a pseudo-binary (Zr 1–x Ce x )Fe 2 system, namely, (Zr 0.16 Ce 0.84 )Fe 2 and (Zr 0.94 Ce 0.06 )Fe 2 , to experimentally validate the ability of our model to predict the Curie temperature of novel compounds. We also provided a detailed discussion on the correlation of the Curie temperature with the de Gennes scaling factor in rare-earth intermetallic compounds and its breakdown below a certain rare-earth content. The electronic structure calculations (density of states and Fermi surface) were performed using the density functional theory on selected compounds (Zr 0.16 Ce 0.84 )Fe 2 and (Zr 0.94 Ce 0.06 )Fe 2 to understand the electronic origin of a strong magnetic exchange. We found that the change in the electronic density of states and electron/hole fillings at the Fermi level directly correlate with the Curie temperature. Notably, our model was able to capture these key electronic structure trends, which show that physics-informed machine learning can play a crucial role in designing new high-performance magnets with improved properties for environmentally sustainable applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unraveling the Effects of Hierarchical Bimodal Microscale Porosity on Thick Electrodes

The thick electrode design is preferential in high-energy lithium-ion batteries (LIBs) systems. However, the sluggish ionic transport in homogeneous porous thick electrodes severely limits the areal capacity at high charging/discharging rates. The hierarchical porous design is a promising approach to mitigate kinetic limitations because it can distribute mass effectively in natural systems. In this study, the effects of bimodal microscale pores are fully investigated in thick electrodes from both architectural and electrochemical perspectives. Notably, by introduction of the bimodal microscale porous structure, the rate capability improves remarkably in thick electrodes with a low porosity (39%). Herein, by combining experimental results with simulations, this work presents a rational design guideline for preparing thick electrodes with a porosity at the commercial level, as well as simultaneous high energy and power densities, which brings new insights into the advanced electrode architecture design in scalable high-energy and high-power energy storage systems for practical applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Competition between Hydrogen and Chalcogen Bonding in Homodimers of Chalcogen Hydrides (H 2 X) 2 , X = O, S, Se, Te

The structural and chemical bonding motifs manifested by the competition between hydrogen and chalcogen bonding in the homodimers of chalcogen hydrides (H 2 X) 2 , where X = O, S, Se, Te have been characterized using high-level electronic structure calculations and analysis of the electron density based on Quasi-atomic orbital (QUAO) and the Symmetry-adapted perturbation theory (SAPT) methods. The QUAO analysis clearly identifies a three-center interaction responsible for either hydrogen or chalcogen bonds: in the former, the σ-bond connecting the donor and hydrogen atom participating in the hydrogen bond interacts with the lone pair on the nucleophile acceptor via the hydrogen atom, while in the latter this same σ-bond interacts with the nucleophile lone pair via the donor chalcogen. The number of minimum energy structures increase dramatically from one for (H 2 O) 2 , three for (H 2 S) 2 , four for (H 2 Se) 2 , and finally six for (H 2 Te) 2 . Furthermore, the emergence of the chalcogen-bonded arrangements appears for (H 2 S) 2 with their subsequent energetic stabilization over the hydrogen-bonded minima manifesting in (H 2 Se) 2 and (H 2 Te) 2 . In particular, one of the (H 2 S) 2 , two of the (H 2 Se) 2 , and three of the (H 2 Te) 2 dimers are chalcogen bonded. Induction plays a small but important role in stabilizing hydrogen over chalcogen-bonded structures, while dispersion is more important for chalcogen bonds.

Chemical structure↗