Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lead”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Design, analysis, and tests of a shuttle-type heat-pipe-cooled leading edge

A one-half scale heat-pipe-cooled leading edge model was designed and fabricated to verify feasibility and performance of a full-scale Phase B shuttle orbiter design. Model performance was investigated experimentally by radiant heating and aerothermal tests and analytically by using a simple technique which predicts heat pipe start-up from the frozen state and also predicts transient and steady-state thermal behavior. Analytical results agree well with experimental results for start-up and steady-state heat pipe operation. The results indicate that variations in angle of attack and roll orientation had a negligible effect on heat pipe performance. The heat pipes effectively isothermalized the leading edge, and reduced peak temperatures to levels compatible with the use temperatures of superalloys. Results of these tests demonstrated the durability of the heat-pipe-cooled leading edge in withstanding earth-entry thermal and mechanical loads and indicate that the use of heat pipes in leading edge structures is a reliable concept for fully reusable hypersonic cruise and space transportation systems.

Camarda, C. J.↗
NASA NTRS1980

The effects of leading edge modifications on the post-stall characteristics of wings

An investigation of the effects of leading edge modifications on the post-stall characteristics of two rectangular planform wings in a series of low speed wind tunnel tests is presented. Abrupt discontinuities in the leading edge shape of the wings were produced by placing a nose glove over a portion of the span or by deflecting sections of a segmented leading edge flap. Six component balance data, oil flow visualization photographs, and pressure distribution measurements were obtained, and tests made to study the development of flow separation at stall on small scale planform wing models. Results of oil flow visualization tests at and beyond stall showed the formation of counter-rotating swirl patterns on the upper surface of the '2-D' and '3-D' wings, and results of a numerical lifting line technique applied to wings with leading edge modifications are included.

Winkelmann, A. E.↗
NASA NTRS1980

Full-scale wind-tunnel investigation of the effects of wing leading-edge modifications on the high angle-of-attack aerodynamic characteristics of a low-wing general aviation airplane

The paper presents the results of a recent investigation to determine the effects of wing leading-edge modifications on the high angle-of-attack aerodynamic characteristics of a low-wing general aviation airplane in the Langley Full-Scale Wind Tunnel. The investigation was conducted to provide aerodynamic information for correlation and analysis of flight-test results obtained for the configuration. The wind-tunnel investigation consisted of force and moment measurements, wing pressure measurements, flow surveys, and flow visualization studies utilizing a tuft grid, smoke and nonintrusive mini-tufts which were illuminated by ultra-violet light. In addition to the tunnel scale system which measured overall forces and moments, the model was equipped with an auxiliary strain-gage balance within the left wing panel to measure lift and drag forces on the outer wing panel independent of the tunnel scale system. The leading-edge modifications studied included partial- and full-span leading-edge droop arrangements as well as leading-edge slats.

Johnson, J. L., Jr.↗
NASA NTRS1980

Numerical prediction of vortex cores of the leading and trailing edges of delta wings

The purpose of the present paper is to predict the roll-up of the vortex sheets emanating from the leading- and trailing-edges of delta wings with emphasis on the interaction of vortex cores beyond the trailing edge. The motivation behind the present work is the recent experimental data published by Hummel. The Nonlinear Discrete-Vortex method (NDV-method) is modified and extended to predict the leading- and trailing-vortex cores beyond the trailing edge. The present model alleviates the problems previously encountered in predicting satisfactory pressure distributions. This is accomplished by lumping the free-vortex lines during the iteration procedure. The leading- and trailing-edge cores and their feeding sheets are obtained as parts of the solution. The numerical results show that the NDV-method is successful in confirming the formation of a trailing-edge core with opposite circulation and opposite roll-up to those of the leading-edge core. This work is a breakthrough in the high angle of attack aerodynamics and moreover, it is the first numerical prediction done on this problem

Kandil, O. A.↗
NASA NTRS1955

Investigation of Porous Gas-Heated Leading-Edge Section for Icing Protection of a Delta Wing

A tip section of a delta wing having an NACA 0004-65 airfoil section and a 600 leading-edge sweepback was equipped with a porous leading-edge section through which hot gas was 'bled for anti-icing. Heating rates for anti-icing were determined for a wide range of icing conditions. The effects of gas flow through the porous leading-edge section on airfoil pressure distribution and drag in dry air were investigated. The drag increase caused by an ice formation on the unheated airfoil was measured for several icing conditions. Experimental porous surface- to free-stream convective heat-transfer coefficients were obtained in dry air and compared with theory. Adequate icing protection was obtained at all icing conditions investigated. Savings in total gas-flow rate up to 42 percent may be obtained with no loss in anti-icing effectiveness by sealing half the upper-surface porous area. Gas flow through the leading-edge section had no appreciable effect on airfoil pressure distribution. The airfoil section drag increased slightly (5-percent average) with gas flow through the porous surface. A heavy glaze-ice formation produced after 10 minutes of icing caused an increase in section drag coefficient of 240 percent. Experimental convective heat-transfer coefficients obtained with hot-gas flow through the porous area in dry air and turbulent flow were 20 to 30 percent lower than the theoretical values for a solid surface under similar conditions. The transition region from laminar to turbulent flow moved forward as the ratio of gas velocity through the porous surface to air-stream velocity was increased.

Bowden, Dean T.↗
NASA NTRS1982

Effects of wing-leading-edge modifications on a full-scale, low-wing general aviation airplane: Wind-tunnel investigation of high-angle-of-attack aerodynamic characteristics

Wing-leading-edge modifications included leading-edge droop and slat configurations having full-span, partial-span, or segmented arrangements. Other devices included wing-chord extensions, fences, and leading-edge stall strips. Good correlation was apparent between the results of wind-tunnel data and the results of flight tests, on the basis of autorotational stability criterion, for a wide range of wing-leading-edge modifications.

Newsom, W. A., Jr.↗
NASA NTRS1982

Study of supersonic wings employing the attainable leading-edge thrust concept

A theoretical study was made of supersonic wing geometries at Mach 1.8, using the attainable leading-edge thrust concept. The attainable thrust method offers a powerful means to improve overall aerodynamic efficiency by identifying wing leading-edge geometries that promote attached flow and by defining a local angle-of-attack range over which attached flow may be obtained. The concept applies to flat and to cambered wings, which leads to the consideration of drooped-wing leading edges for attached flow at high lift coefficients.

Middleton, W. D.↗
NASA NTRS1982

Terrestrial growth of lead-tin-telluride by techniques related to low G growth

A modified Bridgman-Stockbarger furnace was constructed for a study of the solidification of silver, germanium and lead-tin-telluride. The melt-solid interface position with respect to the furnace and its temperature profile was determined by measuring the discontinuity in the slope of temperature as a function of position in the melt and in the solid. The results show that the interface position of the semiconductors germanium and lead-tin-telluride was essentially constant with respect to the furnace and hence the growth rate was constant and equal to the sample translation rate of 0.046 cm/min and 0.178 cm/min in each case. The metal, silver, on the other hand showed a continuous interface migration toward the hot zone of the furnace and always exhibited a growth rate which was higher than the ampoule translation rate. The K sub L/K sub S ratio of lead-tin-telluride was determined to be 2.33 + or - 0.06 where K sub L,S denotes the thermal conductivity of the liquid, solid respectively. The value of K sub L was calculated to be about 0.054 Watt 0.1 cm 0.1 K. The diffusion boundary layer thickness was calculated for lead-tin-telluride to be about 0.05 cm using a liquid diffusivity of .00007 sq cm/sec.

Jesser, W. A.↗
NASA NTRS1983

Effect of lead-aircraft ground-speed on self-spacing performance using a cockpit display of traffic information

A simulator investigation was conducted to determine the effect of the lead-aircraft ground-speed quantization level on self-spacing performance using a Cockpit Display of Traffic Information (CDTI). The study utilized a simulator employing cathode-ray tubes for the primary flight and navigation displays and highly augmented flight control modes. The pilot's task was to follow, and self-space on, a lead aircraft which was performing an idle-thrust profile descent to an instrument landing system (ILS) approach and landing. The spacing requirement was specified in terms of both a minimum distance and a time interval. The results indicate that the ground-speed quantization level, lead-aircraft scenario, and pilot technique had a significant effect on self-spacing performance. However, the ground-speed quantization level only had a significant effect on the performance when the lead aircraft flew a fast final approach.

Kelly, J. R.↗
NASA NTRS1984

An analytical design procedure for the determination of effective leading edge extensions on thick delta wings

An analytical design procedure for leading edge extensions (LEE) was developed for thick delta wings. This LEE device is designed to be mounted to a wing along the pseudo-stagnation stream surface associated with the attached flow design lift coefficient of greater than zero. The intended purpose of this device is to improve the aerodynamic performance of high subsonic and low supersonic aircraft at incidences above that of attached flow design lift coefficient, by using a vortex system emanating along the leading edges of the device. The low pressure associated with these vortices would act on the LEE upper surface and the forward facing area at the wing leading edges, providing an additional lift and effective leading edge thrust recovery. The first application of this technique was to a thick, round edged, twisted and cambered wing of approximately triangular planform having a sweep of 58 deg and aspect ratio of 2.30. The panel aerodynamics and vortex lattice method with suction analogy computer codes were employed to determine the pseudo-stagnation stream surface and an optimized LEE planform shape.

Farhad Ghaffari↗
NASA NTRS1984

Advanced leading edge thermal-structure concept. Direct bond reusable surface insulation to a composite structure

An advanced leading-edge concept was analyzed using the space shuttle leading edge system as a reference model. The comparison indicates that a direct-bond system utilizing a high temperature (2700 F) fibrous refractory composite insulation tile bonded to a high temperature (PI/graphite) composite structure can result in a weight savings of up to 800 lb. The concern that tile damage or loss during ascent would result in adverse entry aerodynamics if a leading edge tile system were used is addressed. It was found from experiment that missing tiles (as many as 22) on the leading edge would not significantly affect the basic force-and-moment aerodynamic coefficients. Additionally, this concept affords a degree of redundancy to a thermal protection system in that the base structure (being a composite material) ablates and neither melts nor burns through when subjected to entry heating in the event tiles are actually lost or damaged during ascent.

Riccitiello, S. R.↗
NASA NTRS1986

Holder for Tinning Microcircuit Leads

Heat-sinking tool holds microcircuits for lead tinning while protecting circuits from heat of tinning solder. Microcircuit holder dips leads in molten solder. Holder shields microcircuit from solder heat while leads immersed and absorbs heat conducted through leads. Thus keeps microcircuit relatively cool. Application tool was developed for requires tinning not closer than 0.02 in. (0.5 mm) from package body or its glass seals.

Gilbert, G. G.↗
NASA NTRS1986

An evaluation of leading-edge flap performance on delta and double-delta wings at supersonic speeds

The aerodynamic performance of leading-edge flaps on three delta double-delta wing planforms having aspect ratios of 1.75, 2.11, and 2.50, have been investigated experimentally. The wings were mounted on a generic fuselage without an inlet canopy, or a vertical tail. The Mach numbers of the flow over the wings were 1.60, 1.90 and 2.16. A primary set of full-span leading-edge flaps with similar root and tip chords were tested on each wing, and several alternate flap planforms were tested on the aspect ratio 1.75 wings. It is found that all leading edge geometries were effective in reducing drag lifting over the range of wing aspect ratios and Mach numbers tested. Greater flap performance was obtained when primary flaps were applied to the delta planform. In general, the primary flap geometry yielded better performance than the alternative geometries tested. Flow visualization techniques were found to be useful for identifying the beneficial effects of leading-edge flap deflection on flow separation as well as fuselage interference effects. Black and white photographs of the delta and double-delta planforms are provided.

Covell, P. F.↗
NASA NTRS1984

Laminar flow control leading edge glove flight test article development

A laminar flow control (LFC) flight test article was designed and fabricated to fit into the right leading edge of a JetStar aircraft. The article was designed to attach to the front spar and fill in approx. 70 inches of the leading edge that are normally occupied by the large slipper fuel tank. The outer contour of the test article was constrained to align with an external fairing aft of the front spar which provided a surface pressure distribution over the test region representative of an LFC airfoil. LFC is achieved by applying suction through a finely perforated surface, which removes a small fraction of the boundary layer. The LFC test article has a retractable high lift shield to protect the laminar surface from contamination by airborne debris during takeoff and low altitude operation. The shield is designed to intercept insects and other particles that could otherwise impact the leading edge. Because the shield will intercept freezing rain and ice, a oozing glycol ice protection system is installed on the shield leading edge. In addition to the shield, a liquid freezing point depressant can be sprayed on the back of the shield.

Pearce, W. E.↗
NASA NTRS1989

Experimental study of pressure and heating rate on a swept cylindrical leading edge resulting from swept shock wave interference

The effects of cylindrical leading edge sweep on surface pressure and heat transfer rate for swept shock wave interference were investigated. Experimental tests were conducted in the Calspan 48-inch Hypersonic Shock Tunnel at a nominal Mach number of 8, nominal unit Reynolds number of 1.5 x 10 to the 6th power per foot, leading edge and incident shock generator sweep angles of 0, 15, and 30 deg, and incident shock generator angle-of-attack fixed at 12.5 deg. Detailed surface pressure and heat transfer rate on the cylindircal leading edge of a swept shock wave interference model were measured at the region of the maximum surface pressure and heat transfer rate. Results show that pressure and heat transfer rate on the cylindrical leading edge of the shock wave interference model were reduced as the sweep was increased over the range of tested parameters. Peak surface pressure and heat transfer rate on the cylinder were about 10 and 30 times the undisturbed flow stagnation point value, respectively, for the 0 deg sweep test. A comparison of the 15 and 30 deg swept results with the 0 deg swept results showed that peak pressure was reduced about 13 percent and 44 percent, respectively, and peak heat transfer rate was reduced about 7 percent and 27 percent, respectively.

Glass, Christopher E.↗
NASA NTRS1990

Computational simulation of flows about hypersonic geometries with sharp leading edges

Hypersonic waverider design has become an important concern in the aerospace industry. As one part of an inverse design effort for waveriders, work has been done to apply existing Euler and Navier-Stokies flow solvers to hypersonic geometries with sharp leading edges. Previously, calculations were done on bodies with rounded leading edges or with conical solutions for the nose initial conditions. In this paper, solutions are computed about waveriders and conical shapes with sharp leading edges without resorting to either shortrcut. All solutions show attached shocks with fully supersonic flows at the nose and along the leading edges. Flows about several waverider shapes are shown, as well as a preliminary cone with inlet calculation to study the shock/inlet interaction.

Jones, Kevin D.↗
NASA NTRS1990

Effect of leading edge roundness on a delta wing in wing-rock motion

The effect of wing leading-edge roundness on wing rock was investigated using flow visualization in a water tunnel. Eighty degree delta wing models were tested on free-to-roll and forced oscillation rigs. The onset of wing rock was delayed by increasing the roundness of the leading edges. The wing rock amplitude and frequency results suggested that damping was increased at lower angles of attack but reduced at higher angles of attack. Vortex lift-off and vortex breakdown, especially during dynamic situations, were strongly affected by the leading edge roundness. Different forms of wing rock motion could be sustained by combinations of vortex breakdown and vortex lift-off. Behaviors of the wing and vortex motions were explained by the influence of leading edge roundness on the separation location, vortex trajectory, and vortex breakdown.

Ng, T. Terry↗
NASA NTRS1991

Leading-edge receptivity for blunt-nose bodies

This research program investigates boundary-layer receptivity in the leading-edge region for bodies with blunt leading edges. Receptivity theory provides the link between the unsteady distrubance environment in the free stream and the initial amplitudes of the instability waves in the boundary layer. This is a critical problem which must be addressed in order to develop more accurate prediction methods for boundary-layer transition. The first phase of this project examines the effects of leading-edge bluntness and aerodynamic loading for low Mach number flows. In the second phase of the project, the investigation is extended to supersonic Mach numbers. Singular perturbation techniques are utilized to develop an asymptotic theory for high Reynolds numbers. In the first year, the asymptotic theory was developed for leading-edge receptivity in low Mach number flows. The case of a parabolic nose is considered. Substantial progress was made on the Navier-Sotkes computations. Analytical solutions for the steady and unsteady potential flow fields were incorporated into the code, greatly expanding the types of free-stream disturbances that can be considered while also significantly reducing the the computational requirements. The time-stepping algorithm was modified so that the potential flow perturbations induced by the unsteady pressure field are directly introduced throughout the computational domain, avoiding an artificial 'numerical diffusion' of these from the outer boundary. In addition, the start-up process was modified by introducing the transient Stokes wave solution into the downstream boundary conditions.

Kerschen, Edward J.↗