Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Active Control of Flow Separation Over an Airfoil

Designing an aircraft without conventional control surfaces is of interest to aerospace community. In this direction, smart actuator devices such as synthetic jets have been proposed to provide aircraft maneuverability instead of control surfaces. In this article, a numerical study is performed to investigate the effects of unsteady suction and blowing on airfoils. The unsteady suction and blowing is introduced at the leading edge of the airfoil in the form of tangential jet. Numerical solutions are obtained using Reynolds-Averaged viscous compressible Navier-Stokes equations. Unsteady suction and blowing is investigated as a means of separation control to obtain lift on airfoils. The effect of blowing coefficients on lift and drag is investigated. The numerical simulations are compared with experiments from the Tel-Aviv University (TAU). These results indicate that unsteady suction and blowing can be used as a means of separation control to generate lift on airfoils.

Ravindran, S. S.↗
NASA NTRS1983

Gear Lubrication and Cooling Experiment and Analysis

A gear tooth temperature analysis was performed using a finite element method combined with a calculated heat input, a calculated oil jet impingement depth, and estimated heat transfer coefficients for the different parts of the gear tooth that are oil cooled and air cooled. Experimental measurements of gear tooth average surface temperature and gear tooth instantaneous surface temperature were made with a fast response, infrared, radiometric microscope. Increasing oil pressure has a significant effect on both average surface temperature and peak surface temperature at loads above 1895 N/cm(1083 lb/in) and speeds of 10,000 and 7500 rpm. Both increasing speed (from 5000 to 10,000 rpm) at constant speed cause a significant rise in the average surface temperature and in the instantaneous peak surface temperatures on the gear teeth. The oil jet pressure required to provide the best cooling for gears is the pressure required to obtain full gear tooth impingement. Calculated results for gear tooth temperatures were close to experimental results for various oil jet impingement depths for identical operating conditions.

Townsend, D. P.↗
NASA NTRS1999

Investigation of Strain/Vorticity and Large-Scale Flow Structure in Turbulent Nonpremixed Jet Flames

Our study will use the microgravity environment to investigate the underlying flow structure of turbulent nonpremixed round jet flames. In particular, we aim to investigate the large-scale turbulent structure using planar laser Mie scattering (PLMS), and the strain rate and vorticity fields using particle image velocimetry (PIV). This work is motivated by recent studies in our laboratory that have led to several interesting observations of nominally momentum-driven turbulent nonpremixed planar flames. First of all, the organized large-scale turbulent structures that are observed in nonreacting planar jets may be substantially modified or suppressed in nonpremixed planar jet flames. Furthermore, a recent study using PIV and planar laser-induced fluorescence of OH has shown that in transitional and turbulent nonpremixed planar jet flames the presence of the flame seems to greatly influence the underlying vorticity and strain fields, as compared to nonreacting jets. For example, the reaction zones in the jet flames are strongly correlated with regions of high vorticity. A related study has demonstrated that vorticity is not correlated in the same way with either iso-scalar surfaces or scalar dissipation layers in nonreacting planar jets. Furthermore, the relationship between strain and the reaction zone appears to be modified by the presence of high levels of heat release. In particular, the strain rate field in planar jet flames exhibits a preferred direction of principal compressive strain that apparently is related to strong shear across the reaction zone. This preferred direction of strain was not observed in nonreacting jets. One of the major problems encountered when conducting these types of studies is that it is difficult to know to what extent buoyancy influences the results. Therefore, the microgravity environment provides us with an excellent opportunity to explore these issues without the complicating effects of buoyancy. This is particularly the case when studying flames that are transitional between laminar and turbulent states. For example, the strong correlation of vorticity with the reaction zone (discussed above) was observed in both transitional and turbulent planar flames, but the effect was stronger for the transitional case. To date, the reason for the presence of the vorticity-reaction zone correlation is not known, although vorticity production via baroclinic torque is a likely cause. The microgravity environment will allow us to specifically determine whether the vorticity is produced by baroclinic torque resulting from the flame density gradient acting with the hydrostatic pressure gradient.AAdditional details of the planned experiments are provided.

Clemens, N. T.↗
NASA NTRS2007

Granular Mechanics and Surface Systems Lab

The cratering of sand under gas jets is observed to further understanding of soil in hopes to further understand lunar soil. Lunar soil is important to understand because it is causing problems with the materials taken into space including the shuttle. Lunar soil is not rounded like beach sand. Lunar soil is sharp like little particles of glass, and some times when blown they can hook on to one another and become bigger particles. The experiments are designed to help to understand some of the basic physics in how the shuttle jets will interact with lunar soil and how to control the lunar soil. These experiments investigate the diameter of the gas jet and the size of the sand grains to determine how these parameters affect the erosion rate and the cratering processes. Therefore, the experiments preformed will point out what is dependent and what is independent.

Randle, Leah↗
NASA NTRS2003

Toward the Active Control of Heat Transfer in the Hot Gas Path of Gas Turbines

The work at NASA this summer has focused on assisting the Professor's project, namely "Toward the Active Control of Heat Transfer in the Hot Gas Path of Gas Turbines." The mode of controlling the Heat Transfer that the project focuses on is film cooling. Film cooling is used in high temperature regions of a gas turbine and extends the life of the components exposed to these extreme temperatures. A "cool" jet of air is injected along the surface of the blade and this layer of cool air shields the blade from the high temperatures. Cool is a relative term. The hot gas path temperatures reach on the order of 1500 to 2000 K. The "coo" air is on the order of 700 to 1000 K. This cooler air is bled off of an appropriate compressor stage. The next parameter of interest is the jet s position and orientation in the flow-field.

Oertling, Jeremiah E.↗
NASA NTRS1993

Lift augmentation for highly swept wing aircraft

A pair of spaced slots, disposed on each side of an aircraft centerline and spaced well inboard of the wing leading edges, are provided in the wing upper surfaces and directed tangentially spanwise toward thin sharp leading wing edges of a highly swept, delta wing aircraft. The slots are individually connected through separate plenum chambers to separate compressed air tanks and serve, collectively, as a system for providing aircraft lift augmentation. A compressed air supply is tapped from the aircraft turbojet power plant. Suitable valves, under the control of the aircraft pilot, serve to selective provide jet blowing from the individual slots to provide spanwise sheets of jet air closely adjacent to the upper surfaces and across the aircraft wing span to thereby create artificial vortices whose suction generate additional lift on the aircraft. When desired, or found necessary, unequal or one-side wing blowing is employed to generate rolling moments for augmented lateral control. Trailing flaps are provided that may be deflected differentially, individually, or in unison, as needed for assistance in take-off or landing of the aircraft.

Rao, Dhanvada M.↗
NASA NTRS1993

Separated flow generated by a vectored jet in a crossflow

Results of an experimental investigation to determine the characteristics of the separated flow region generated by a subsonic vectored rectangular jet in a subsonic crossflow is presented. Using surface visualization techniques, it was found that the upstream separated flow consist of horseshoe vortices that are formed periodically with a frequency corresponding to that of the vortex shedding behind the jet. The size of the recirculation region around the jet is found to decrease with increasing jet vector angle. The variation of the mean primary separation distance upstream of the jet, with velocity ratio revealed the existence of two different flow regimes. The change from one to the other depends on the velocity ratio and the jet vector angle. It is shown that the Strouhal number, based on the vortex shedding frequency and a combination of jet exit and freestream velocities, varies uniquely with velocity ratio.

Krothapalli, A.↗
NASA NTRS1983

Interaction of two-dimensional transverse jet with a supersonic mainstream

The interaction of a two dimensional sonic jet injected transversely into a confined main flow was studied. The main flow consisted of air at a Mach number of 2.9. The effects of varying the jet parameters on the flow field were examined using surface pressure and composition data. Also, the downstream flow field was examined using static pressure, pitot pressure, and composition profile data. The jet parameters varied were gapwidth, jet static pressure, and injectant species of either helium or nitrogen. The values of the jet parameters used were 0.039, 0.056, and 0.109 cm for the gapwidth and 5, 10, and 20 for the jet to mainstream static pressure ratios. The features of the flow field produced by the mixing and interaction of the jet with the mainstream were related to the jet momentum. The data were used to demonstrate the validity of an existing two dimensional elliptic flow code.

Kraemer, G. O.↗
NASA NTRS2000

Flight Control Using Distributed Shape-Change Effector Arrays

Recent discoveries in material science and fluidics have been used to create a variety of novel effector devices that offer great potential to enable new approaches to aerospace vehicle flight control. Examples include small inflatable blisters, shape-memory alloy diaphragms, and piezoelectric patches that may be used to produce distortions or bumps on the surface of an airfoil to generate control moments. Small jets have also been used to produce a virtual shape-change through fluidic means by creating a recirculation bubble on the surface of an airfoil. An advanced aerospace vehicle might use distributed arrays of hundreds of such devices to generate moments for stabilization and maneuver control, either augmenting or replacing conventional ailerons, flaps or rudders. This research demonstrates the design and use of shape-change device arrays for a tailless aircraft in a low-rate maneuvering application. A methodology for assessing the control authority of the device arrays is described, and a suite of arrays is used in a dynamic simulation to illustrate allocation and deployment methodologies. Although the authority of the preliminary shape-change array designs studied in this paper appeared quite low, the simulation results indicate that the effector suite possessed sufficient authority to stabilize and maneuver the vehicle in mild turbulence.

Raney, David L.↗
NASA NTRS1949

Jet Diffusion in Proximity of a Wall

When auxiliary jet engines are installed on airframes; as well as in some new designs, the jet engines are mounted in such a way that the jet stream exhausts in close proximity to the fuselage. This report deals with the behavior of the jet in close proximity to a two-dimensional surface. The experiments were made to find out whether the axially symmetric stream tends to approach the flat surface. This report is the last of a series of four partial test reports of the Goettingen program for the installation of jet engines, dated October 12, 1943. This report is the complement of the report on intake in close proximity to a wall.

Kuechemann, D.↗
NASA NTRS2011

Using Jet Observations to Constrain Enceladus' Rotation State

Observations of Enceladus have revealed active jets of material erupting from cracks on its surface. It has been proposed that diurnal tidal stress may open these cracks daily when they experience tensile stresses across them, allowing eruptions to occur. An analysis of the tidal stress on jet source regions, as identified by the triangulation of jet observations, finds that there is a correlation between observations and tensile stress on the cracks. However, not all regions are predicted to be in tension when jets were observed to be active. Enceladus' rotation state, such as a physical libration or obliquity, will affect the diurnal stresses on these cracks, changing when in its orbit they experience tension and compression. We will use observations of jet activity from 2005-2007 to place constraints on rotation states of Enceladus.

Hurford, Terry A.↗
NASA NTRS2016

Lighting Condition Analysis for Mars' Moon Phobos

This study used high fidelity computer simulation to investigate the lighting conditions, specifically the solar radiation flux over the surface, on Phobos. Ephemeris data from the Jet Propulsion Laboratory (JPL) DE405 model was used to model the state of the Sun, Earth, Moon, and Mars. An occultation model was developed to simulate Phobos' self-shadowing and its solar eclipses by Mars. The propagated Phobos state was compared with data from JPL's Horizon system to ensure the accuracy of the result. Results for Phobos lighting conditions over one Martian year are presented, which include the duration of solar eclipses, average solar radiation intensity, surface exposure time, available energy per unit area for sun tracking arrays, and available energy per unit area for fixed arrays (constrained by incident angle). The results show that: Phobos' solar eclipse time varies throughout the Martian year, with longer eclipse durations during the Martian spring and fall seasons and no eclipses during the Martian summer and winter seasons; solar radiation intensity is close to minimum at the summer solstice and close to maximum at the winter solstice; exposure time per orbit is relatively constant over the surface during the spring and fall but varies with latitude during the summer and winter; and Sun tracking solar arrays generate more energy than a fixed solar array. A usage example of the result is also present in this paper to demonstrate the utility.

Li, Zu Qun↗
NASA NTRS2016

Lighting Condition Analysis for Mars' Moon Phobos

This study used high fidelity computer simulation to investigate the lighting conditions, specifically the solar radiation flux over the surface, on Phobos. Ephemeris data from the Jet Propulsion Laboratory (JPL) DE405 model was used to model the state of the Sun, Earth, Moon, and Mars. An occultation model was developed to simulate Phobos' self-shadowing and its solar eclipses by Mars. The propagated Phobos state was compared with data from JPL's Horizon system to ensure the accuracy of the result. Results for Phobos lighting conditions over one Martian year are presented, which include the duration of solar eclipses, average solar radiation intensity, surface exposure time, and radiant exposure for both sun tracking and fixed solar arrays. The results show that: Phobos' solar eclipse time varies throughout the Martian year, with longer eclipse durations during the Martian northern spring and fall seasons and no eclipses during the Martian northern summer and winter seasons; solar radiation intensity is close to minimum in late spring and close to maximum in late fall; exposure time per orbit is relatively constant over the surface during the spring and fall but varies with latitude during the summer and winter; and Sun tracking solar arrays generate more energy than a fixed solar array. A usage example of the result is also present in this paper to demonstrate the utility.

Li, Zu Qun↗
NASA NTRS2016

Lighting Condition Analysis for Mars Moon Phobos

A manned mission to Phobos may be an important precursor and catalyst for the human exploration of Mars, as it will fully demonstrate the technologies for a successful Mars mission. A comprehensive understanding of Phobos' environment such as lighting condition and gravitational acceleration are essential to the mission success. The lighting condition is one of many critical factors for landing zone selection, vehicle power subsystem design, and surface mobility vehicle path planning. Due to the orbital characteristic of Phobos, the lighting condition will change dramatically from one Martian season to another. This study uses high fidelity computer simulation to investigate the lighting conditions, specifically the solar radiation flux over the surface, on Phobos. Ephemeris data from the Jet Propulsion Laboratory (JPL) DE405 model was used to model the state of the Sun, the Earth, and Mars. An occultation model was developed to simulate Phobos' self-shadowing and its solar eclipses by Mars. The propagated Phobos' state was compared with data from JPL's Horizon system to ensure the accuracy of the result. Results for Phobos lighting condition over one Martian year are presented in this paper, which include length of solar eclipse, average solar radiation intensity, surface exposure time, total maximum solar energy, and total surface solar energy (constrained by incident angle). The results show that Phobos' solar eclipse time changes throughout the Martian year with the maximum eclipse time occurring during the Martian spring and fall equinox and no solar eclipse during the Martian summer and winter solstice. Solar radiation intensity is close to minimum at the summer solstice and close to maximum at the winter solstice. Total surface exposure time is longer near the north pole and around the anti- Mars point. Total maximum solar energy is larger around the anti-Mars point. Total surface solar energy is higher around the anti-Mars point near the equator. The results from this study and others like it will be important in determining landing site selection, vehicle system design and mission operations for the human exploration of Phobos and subsequently Mars.

Li, Zu Qun↗
NASA NTRS2018

The Cause of Faint Coronal Jets from Emerging-Flux Regions in Solar Coronal Holes

Coronal jets are transient thin bursts of magnetically channeled solar material from the surface into the corona. They are brightest at their base, with a bright point (jet bright point, JBP) at an edge of the base. Early studies (Shibata et al. 1992) suggested that jets result from magnetic flux emergence: a small bipole emerges into unipolar ambient field, driving the jet and forming the JBP via interchange reconnection. More recent studies, using higher-cadence, higher-resolution, and broader wavelength coverage than before, show that prominent coronal jets are usually driven by a minifialment eruption (Sterling et al. 2015), and that, rather than flux emergence, flux cancelation usually prepares and triggers the eruption (Panesar et al. 2016). Here, we analyzed eight emerging flux regions to determine whether the emerging flux directly drove any coronal jets. We used EUV images from the Solar Dynamics Observatory (SDO)/Atmospheric Imaging Assembly (AIA) (in 304, 171, 211, 193, and 94 Å channels), and magnetograms from SDO/Helioseismic & Magnetic Imager (HMI). All eight regions produced jet-like features that were weak in intensity (“faint jets’’), by which we mean they were so faint that we likely would not have identified them as jets had we initially searched for jets in AIA movies alone (as in, e.g., Panesar et al. 2016, Moore et al. 2013) without knowing whether the base was an emerging bipole. In seven of the eight regions, all jets (faint or prominent) erupted from locations where one leg of the emerging bipole was evidently canceling with an ambient opposite-polarity flux clump. The eighth case, the one that had the fastest flux emergence, possibly made faint jets by the flux-emergence mechanism, but these too might instead have resulted from flux cancelation.

Harden, Abigail R.↗
NASA NTRS1976

New developments in blown flap noise technology

The noise technology relating to blown-flap systems is reviewed. There are three general sources of noise: turbomachinery, airframe, and the interaction noise of the jet blowing on the flaps. The latter noise-source area is the most critical and the main subject dicussed. Characteristics of lower surface blown and upper surface blown systems are described, including noise spectra, directivity, jet velocity characteristics, aircraft geometric variation effects, and aircraft forward speed effects. Noise reduction concepts are described, including slowing down the jet flow field by devices and engine cycle modifications, structural geometry and shielding modifications, local flow field modifications of the passive and active type, and the absorption of noise. It is concluded that, while there has been considerable progress in the past several years, low noise characteristics in blown flap aircraft must be largely built in by better application of low noise principles during the design.

Gibson, J. S.↗
NASA NTRS1978

A computer program for calculating symmetrical aerodynamic characteristics and lateral-directional stability derivatives of wing-body combinations with blowing jets

The necessary information for using a computer program to calculate the aerodynamic characteristics under symmetrical flight conditions and the lateral-directional stability derivatives of wing-body combinations with upper-surface-blowing (USB) or over-wing-blowing (OWB) jets are described. The following new features were added to the program: (1) a fuselage of arbitrary body of revolution has been included. The effect of wing-body interference can now be investigated, and (2) all nine lateral-directional stability derivatives can be calculated. The program is written in FORTRAN language and runs on CDC Cyber 175 and Honeywell 66/60 computers.

Lan, C. E.↗