Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High performance Computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Numerical Optimization of the Thermal Field in Bridgman Detached Growth

The global modeling of the thermal field in two vertical Bridgman-like crystal growth configurations, has been performed to get optimal thermal conditions for a successful detached growth of Ge and CdTe crystals. These computations are performed using the CrysMAS code and expand upon our previous analysis [1] that propose a new mechanism involving the thermal field and meniscus position to explain stable conditions for dewetted Bridgman growth. The analysis of the vertical Bridgman configuration with two heaters, used by Palosz et al. for the detached growth of Ge, shows, consistent with their results, that the large wetting angle of germanium on boron nitride surfaces was an important factor to promote a successful detached growth. Our computations predict that by initiating growth much higher into the hot zone of the furnace, the thermal conditions will be favorable for continued detachment even for systems that did not exhibit high contact angles. The computations performed for a vertical gradient freeze configuration with three heaters representative of that used for the detached growth of CdTe, show favorable thermal conditions for dewetting during the entirely growth run described. Improved thermal conditions are also predicted for coated silica crucibles when the solid-liquid interface advances higher into the hot zone during the solidification process. The second set of experiments on CdTe growth described elsewhere has shown the reattachment of the crystal to the crucible after few centimeters of dewetted growth. The thermal modeling of this configuration shows a second solidification front appearing at the top of the sample and approaching the middle line across the third heater. In these conditions, the crystal grows detached from the bottom, but will be attached to the crucible in the upper part because of the solidification without gap in this region. The solidification with two interfaces can be avoided when the top of the sample is positioned below the middle position of the third furnace.

Stelian, C.↗
NASA NTRS1999

ACTS 118x: High Speed TCP Interoperability Testing

With the recent explosion of the Internet and the enormous business opportunities available to communication system providers, great interest has developed in improving the efficiency of data transfer over satellite links using the Transmission Control Protocol (TCP) of the Internet Protocol (IP) suite. The NASA's ACTS experiments program initiated a series of TCP experiments to demonstrate scalability of TCP/IP and determine to what extent the protocol can be optimized over a 622 Mbps satellite link. Through partnerships with the government technology oriented labs, computer, telecommunication, and satellite industries NASA Glenn was able to: (1) promote the development of interoperable, high-performance TCP/IP implementations across multiple computing / operating platforms; (2) work with the satellite industry to answer outstanding questions regarding the use of standard protocols (TCP/IP and ATM) for the delivery of advanced data services, and for use in spacecraft architectures; and (3) conduct a series of TCP/IP interoperability tests over OC12 ATM over a satellite network in a multi-vendor environment using ACTS. The experiments' various network configurations and the results are presented.

Brooks, David E.↗
NASA NTRS2007

High-Performance, Radiation-Hardened Electronics for Space Environments

The Radiation Hardened Electronics for Space Environments (RHESE) project endeavors to advance the current state-of-the-art in high-performance, radiation-hardened electronics and processors, ensuring successful performance of space systems required to operate within extreme radiation and temperature environments. Because RHESE is a project within the Exploration Technology Development Program (ETDP), RHESE's primary customers will be the human and robotic missions being developed by NASA's Exploration Systems Mission Directorate (ESMD) in partial fulfillment of the Vision for Space Exploration. Benefits are also anticipated for NASA's science missions to planetary and deep-space destinations. As a technology development effort, RHESE provides a broad-scoped, full spectrum of approaches to environmentally harden space electronics, including new materials, advanced design processes, reconfigurable hardware techniques, and software modeling of the radiation environment. The RHESE sub-project tasks are: SelfReconfigurable Electronics for Extreme Environments, Radiation Effects Predictive Modeling, Radiation Hardened Memory, Single Event Effects (SEE) Immune Reconfigurable Field Programmable Gate Array (FPGA) (SIRF), Radiation Hardening by Software, Radiation Hardened High Performance Processors (HPP), Reconfigurable Computing, Low Temperature Tolerant MEMS by Design, and Silicon-Germanium (SiGe) Integrated Electronics for Extreme Environments. These nine sub-project tasks are managed by technical leads as located across five different NASA field centers, including Ames Research Center, Goddard Space Flight Center, the Jet Propulsion Laboratory, Langley Research Center, and Marshall Space Flight Center. The overall RHESE integrated project management responsibility resides with NASA's Marshall Space Flight Center (MSFC). Initial technology development emphasis within RHESE focuses on the hardening of Field Programmable Gate Arrays (FPGA)s and Field Programmable Analog Arrays (FPAA)s for use in reconfigurable architectures. As these component/chip level technologies mature, the RHESE project emphasis shifts to focus on efforts encompassing total processor hardening techniques and board-level electronic reconfiguration techniques featuring spare and interface modularity. This phased approach to distributing emphasis between technology developments provides hardened FPGA/FPAAs for early mission infusion, then migrates to hardened, board-level, high speed processors with associated memory elements and high density storage for the longer duration missions encountered for Lunar Outpost and Mars Exploration occurring later in the Constellation schedule.

Keys, Andrew S.↗
NASA NTRS1991

Design of optimal second-order state estimators

The present consideration of the design of online computation-saving second-order state estimators for second-order vector-matrix differential systems proposes a class of such estimators which is proven to possess guaranteed convergence. A class of optimal second-order estimators is then obtained, and the conditions required for optimality are identified. The estimator proposed offers high performance in conjunction with online computation reductions sufficiently great to allow the estimation of the large number of state variables associated with control of large, flexible space structures represented by high-dimensional second-order systems.

Joshi, Suresh M.↗
NASA NTRS1973

Development of gallium arsenide solar cells

The potential of ion implantation as a means of developing gallium arsenide solar cells with high efficiency performance was investigated. Computer calculations on gallium arsenide cell characteristics are presented to show the effects of surface recombination, junction space-charge recombination, and built-in fields produced by nonuniform doping of the surface region. The fabrication technology is summarized. Electrical and optical measurements on samples of solar cells are included.

Source record↗
NASA NTRS1988

Consistent Data Distribution Over Optical Links

Fiber optics combined with IDE's provide consistent data communication between fault-tolerant computers. Data-transmission-checking system designed to provide consistent and reliable data communications for fault-tolerant and highly reliable computers. New technique performs variant of algorithm for fault-tolerant computers and uses fiber optics and independent decision elements (IDE's) to require fewer processors and fewer transmissions of messages. Enables fault-tolerant computers operating at different levels of redundancy to communicate with each other over triply redundant bus. Level of redundancy limited only by maximum number of wavelengths active on bus.

Palumbo, Daniel L.↗
NASA NTRS1991

The role of the remotely augmented vehicle (RAV) laboratory in flight research

This paper presents on overview of the unique capabilities and historical significance of the Remotely Augmented Vehicle (RAV) Laboratory at the NASA Dryden Flight Research Facility. The report reviews the role of the RAV Laboratory in enhancing flight test programs and efficient testing of new aircraft control laws. The history of the RAV Laboratory is discussed with a sample of its application using the X-29 aircraft. The RAV Laboratory allows for closed- or open-loop augmentation of the research aircraft while in flight using ground-based, high performance real-time computers. Telemetry systems transfer sensor and control data between the ground and the aircraft. The RAV capability provides for enhanced computational power, improved flight data quality, and alternate methods for the testing of control system concepts. The Laboratory is easily reconfigured to reflect changes within a flight program and can be adapted to new flight programs.

Cohen, Dorothea↗
NASA NTRS1998

Genetically Engineered Microelectronic Infrared Filters

A genetic algorithm is used for design of infrared filters and in the understanding of the material structure of a resonant tunneling diode. These two components are examples of microdevices and nanodevices that can be numerically simulated using fundamental mathematical and physical models. Because the number of parameters that can be used in the design of one of these devices is large, and because experimental exploration of the design space is unfeasible, reliable software models integrated with global optimization methods are examined The genetic algorithm and engineering design codes have been implemented on massively parallel computers to exploit their high performance. Design results are presented for the infrared filter showing new and optimized device design. Results for nanodevices are presented in a companion paper at this workshop.

Cwik, Tom↗
NASA NTRS1998

A Comparison of Automatic Parallelization Tools/Compilers on the SGI Origin 2000 Using the NAS Benchmarks

Porting applications to new high performance parallel and distributed computing platforms is a challenging task. Since writing parallel code by hand is extremely time consuming and costly, porting codes would ideally be automated by using some parallelization tools and compilers. In this paper, we compare the performance of the hand written NAB Parallel Benchmarks against three parallel versions generated with the help of tools and compilers: 1) CAPTools: an interactive computer aided parallelization too] that generates message passing code, 2) the Portland Group's HPF compiler and 3) using compiler directives with the native FORTAN77 compiler on the SGI Origin2000.

Saini, Subhash↗
NASA NTRS2016

AIRNOISE: A Tool for Preliminary Noise-Abatement Terminal Approach Route Design

Noise from aircraft in the airport vicinity is one of the leading aviation-induced environmental issues. The FAA developed the Integrated Noise Model (INM) and its replacement Aviation Environmental Design Tool (AEDT) software to assess noise impact resulting from all aviation activities. However, a software tool is needed that is simple to use for terminal route modification, quick and reasonably accurate for preliminary noise impact evaluation and flexible to be used for iterative design of optimal noise-abatement terminal routes. In this paper, we extend our previous work on developing a noise-abatement terminal approach route design tool, named AIRNOISE, to satisfy this criterion. First, software efficiency has been significantly increased by over tenfold using the C programming language instead of MATLAB. Moreover, a state-of-the-art high performance GPU-accelerated computing module is implemented that was tested to be hundreds time faster than the C implementation. Secondly, a Graphical User Interface (GUI) was developed allowing users to import current terminal approach routes and modify the routes interactively to design new terminal approach routes. The corresponding noise impacts are then calculated and displayed in the GUI in seconds. Finally, AIRNOISE was applied to Baltimore-Washington International Airport terminal approach route to demonstrate its usage.

aircraft noise↗
NASA NTRS2018

Real-Time Data Products and the Intelligent Payload Module

This presentation goes over the last 10 years of effort to prototype various aspects fo the HyspIRI Intelligent Payload Module (IPM). This was a mission requirement and various protoytpe efforts were conducted to bring risk down. The effort goes over various hardware and software protoytpe efforts.

high performance space computing↗
NASA NTRS2019

Laminar-Turbulent Transition Upstream of the Entropy-Layer Swallowing Location in Hypersonic Boundary Layers

Numerical and experimental studies have demonstrated that modal growth of planar Mack modes is responsible for laminar-turbulent transition on sharp cones at hypersonic speeds. However, the physical mechanisms that lead to transition onset upstream of the entropy-layer swallowing location over sufficiently blunt geometries are not well understood as yet. Modal amplification is too weak or nonexistent to initiate transition at moderate-to-large bluntness values. Nonmodal analysis shows that, with increasing nose bluntness, both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification. However, because of the relatively weak signature of the nonmodal traveling disturbances within the boundary-layer region, the route to transition onset subsequent to the nonmodal growth remains unclear. Thus, nonlinear parabolized stability equations (NPSE) and direct numerical simulations (DNS) have been used to investigate the potential transition mechanisms over a 7-degree blunt cone that was tested in the AFRL Mach-6 high-Reynoldsnumber facility. Computations are performed to separately follow the nonlinear development of two classes of inflow disturbances, namely, a pair of oblique traveling waves with equal but opposite angles with respect to the mean flow direction and a planar traveling wave. Results in both cases show an excellent agreement between the NPSE and DNS predictions, establishing that the NPSE is an accurate and efficient technique for predicting the nonlinear development for these particular nonmodal traveling disturbances. Computations reveal that the oblique mode interactions lead to the generation of stationary streaks inside the boundary layer that, in turn, facilitate the growth of a subharmonic sinuous disturbance. For relatively modest amplitudes of the inflow disturbance, the oblique-mode breakdown can lead to transition at the measured location of transition onset during the experiment. On the other hand, the nonlinear development of a planar traveling wave leads to the formation of inclined structures just above the boundary-layer edge and these structures are strongly reminiscent of the transitional events observed during blunt cone experiments by using schlieren flow visualizations.

Entropy↗
NASA NTRS2021

Identifying Planetary Transit Candidates in TESS Full-frame Image Light Curves via Convolutional Neural Networks

The Transiting Exoplanet Survey Satellite(TESS)mission measured light from stars in∼75% of the sky throughout its 2 yr primary mission, resulting in millions of TESS 30-minute-cadence light curves to analyze in the search for transiting exoplanets. To search this vast data trove for transit signals, we aim to provide an approach that both is computationally efficient and produces highly performant predictions. This approach minimizes the required human search effort. We present a convolutional neural network, which we train to identify planetary transit signals and dismiss false positives. To make a prediction for a given light curve, our network requires no prior transit parameters identified using other methods. Our network performs inference on a TESS 30-minute-cadence light curve in∼5 ms on a single GPU, enabling large-scale archival searches. We present 181 new planet candidates identified by our network, which pass subsequent human vetting designed to rule out false positives.Our neural network model is additionally provided as open-source code for public use and extension

Gregory Olmschenk↗
NASA NTRS1999

The SGI/CRAY T3E: Experiences and Insights

The focus of the HPCC Earth and Space Sciences (ESS) Project is capability computing - pushing highly scalable computing testbeds to their performance limits. The drivers of this focus are the Grand Challenge problems in Earth and space science: those that could not be addressed in a capacity computing environment where large jobs must continually compete for resources. These Grand Challenge codes require a high degree of communication, large memory, and very large I/O (throughout the duration of the processing, not just in loading initial conditions and saving final results). This set of parameters led to the selection of an SGI/Cray T3E as the current ESS Computing Testbed. The T3E at the Goddard Space Flight Center is a unique computational resource within NASA. As such, it must be managed to effectively support the diverse research efforts across the NASA research community yet still enable the ESS Grand Challenge Investigator teams to achieve their performance milestones, for which the system was intended. To date, all Grand Challenge Investigator teams have achieved the 10 GFLOPS milestone, eight of nine have achieved the 50 GFLOPS milestone, and three have achieved the 100 GFLOPS milestone. In addition, many technical papers have been published highlighting results achieved on the NASA T3E, including some at this Workshop. The successes enabled by the NASA T3E computing environment are best illustrated by the 512 PE upgrade funded by the NASA Earth Science Enterprise earlier this year. Never before has an HPCC computing testbed been so well received by the general NASA science community that it was deemed critical to the success of a core NASA science effort. NASA looks forward to many more success stories before the conclusion of the NASA-SGI/Cray cooperative agreement in June 1999.

Bernard, Lisa Hamet↗
NASA NTRS2000

Numerical Propulsion System Simulation: An Overview

The cost of implementing new technology in aerospace propulsion systems is becoming prohibitively expensive and time consuming. One of the main contributors to the high cost and lengthy time is the need to perform many large-scale hardware tests and the inability to integrate all appropriate subsystems early in the design process. The NASA Glenn Research Center is developing the technologies required to enable simulations of full aerospace propulsion systems in sufficient detail to resolve critical design issues early in the design process before hardware is built. This concept, called the Numerical Propulsion System Simulation (NPSS), is focused on the integration of multiple disciplines such as aerodynamics, structures and heat transfer with computing and communication technologies to capture complex physical processes in a timely and cost-effective manner. The vision for NPSS, as illustrated, is to be a "numerical test cell" that enables full engine simulation overnight on cost-effective computing platforms. There are several key elements within NPSS that are required to achieve this capability: 1) clear data interfaces through the development and/or use of data exchange standards, 2) modular and flexible program construction through the use of object-oriented programming, 3) integrated multiple fidelity analysis (zooming) techniques that capture the appropriate physics at the appropriate fidelity for the engine systems, 4) multidisciplinary coupling techniques and finally 5) high performance parallel and distributed computing. The current state of development in these five area focuses on air breathing gas turbine engines and is reported in this paper. However, many of the technologies are generic and can be readily applied to rocket based systems and combined cycles currently being considered for low-cost access-to-space applications. Recent accomplishments include: (1) the development of an industry-standard engine cycle analysis program and plug 'n play architecture, called NPSS Version 1, (2) A full engine simulation that combines a 3D low-pressure subsystem with a 0D high pressure core simulation. This demonstrates the ability to integrate analyses at different levels of detail and to aerodynamically couple components, the fan/booster and low-pressure turbine, through a 3D computational fluid dynamics simulation. (3) Simulation of all of the turbomachinery in a modern turbofan engine on parallel computing platform for rapid and cost-effective execution. This capability can also be used to generate full compressor map, requiring both design and off-design simulation. (4) Three levels of coupling characterize the multidisciplinary analysis under NPSS: loosely coupled, process coupled and tightly coupled. The loosely coupled and process coupled approaches require a common geometry definition to link CAD to analysis tools. The tightly coupled approach is currently validating the use of arbitrary Lagrangian/Eulerian formulation for rotating turbomachinery. The validation includes both centrifugal and axial compression systems. The results of the validation will be reported in the paper. (5) The demonstration of significant computing cost/performance reduction for turbine engine applications using PC clusters. The NPSS Project is supported under the NASA High Performance Computing and Communications Program.

Lytle, John K.↗
NASA NTRS1990

Mapping unstructured grid problems to the connection machine

We present a highly parallel graph mapping technique that enables one to solve unstructured grid problems on massively parallel computers. Many implicit and explicit methods for solving discretizated partial differential equations require each point in the discretization to exchange data with its neighboring points every time step or iteration. The time spent communicating can limit the high performance promised by massively parallel computing. To eliminate this bottleneck, we map the graph of the irregular problem to the graph representing the interconnection topology of the computer such that the sum of the distances that the messages travel is minimized. We show that, in comparison to a naive assignment of processors, our heuristic mapping algorithm significantly reduces the communication time on the Connection Machine, CM-2.

Hammond, Steven W.↗
NASA NTRS2015

Boundary Layer Transition and Trip Effectiveness on an Apollo Capsule in the JAXA High Enthalpy Shock Tunnel (HIEST) Facility

Computational assessments were performed to size boundary layer trips for a scaled Apollo capsule model in the High Enthalpy Shock Tunnel (HIEST) facility at the JAXA Kakuda Space Center in Japan. For stagnation conditions between 2 MJ/kg and 20 MJ/kg and between 10 MPa and 60 MPa, the appropriate trips were determined to be between 0.2 mm and 1.3 mm high, which provided kappa/delta values on the heatshield from 0.15 to 2.25. The tripped configuration consisted of an insert with a series of diamond shaped trips along the heatshield downstream of the stagnation point. Surface heat flux measurements were obtained on a capsule with a 250 mm diameter, 6.4% scale model, and pressure measurements were taken at axial stations along the nozzle walls. At low enthalpy conditions, the computational predictions agree favorably to the test data along the heatshield centerline. However, agreement becomes less favorable as the enthalpy increases conditions. The measured surface heat flux on the heatshield from the HIEST facility was under-predicted by the computations in these cases. Both smooth and tripped configurations were tested for comparison, and a post-test computational analysis showed that kappa/delta values based on the as-measured stagnation conditions ranged between 0.5 and 1.2. Tripped configurations for both 0.6 mm and 0.8 mm trip heights were able to effectively trip the flow to fully turbulent for a range of freestream conditions.

Kirk, Lindsay C.↗