Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite/Epoxy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Structural efficiency study of graphite-epoxy aircraft rib structures

Attention is given to the structural efficiencies obtainable with optimally designed graphite/epoxy wing rib panel configurations that are potentially economically manufacturable. Some ribs are commonly used as fuel cell closeout panels, and are accordingly subjected to out-of-plane pressure loads in addition to the in-plane axial compressive and shear loads resulting from the wing loading. The present minimum-weight panel designs satisfy buckling and strength constraints for wing rib panels subjected to a wide range of combined load conditions.

Swanson, Gary D.↗

Residual thermal and moisture influences on the free-edge delamination of laminated composites

A simple delamination analysis method is developed. It is based on a shear-type deformation theory and includes hygrothermal effects. The method is applied to mixed-mode edge delamination specimens made of T300/5208 graphite/epoxy. It is found that residual thermal influences were alleviated when moisture stresses were included. Thermal effects on the interlaminar shear stress and total energy release rate were totally alleviated for the same specific moisture content. Moreover, this value of moisture content was not significantly affected by the stacking sequence for the laminates considered.

Armanios, Erian A.↗

Probabilistic composite micromechanics

Probabilistic composite micromechanics methods are developed that simulate expected uncertainties in unidirectional fiber composite properties. These methods are in the form of computational procedures using Monte Carlo simulation. A graphite/epoxy unidirectional composite (ply) is studied to demonstrate fiber composite material properties at the micro level. Regression results are presented to show the relative correlation between predicted and response variables in the study.

Stock, T. A.↗

Passive damping for space truss structures

Theoretical and experimental studies of passive damping techniques in truss-type structures are presented, with emphasis on the use of viscoelastic damping in the parallel load path. The constraining member length is shown to be a convenient design variable for enhancing damping performance. Results are presented for integral damping members made of thin-wall aluminum tubes, concentric constraining members, and viscoelastic materials in a six-bay truss structure at low frequency and low dynamic strain conditions. Integral members with graphite/epoxy constraining members exhibited relatively low damping values due to the possible polymer interaction during the cocure stage.

Chen, Gun-Shing↗

Degradation of graphite-epoxy due to electron radiation

Experimental results are presented showing that electron irradiation has a variable effect on the properties of graphite-epoxy depending upon the test temperature and the property of interest. In general, compression properties are improved at cold temperature and degraded at elevated temperature. With the exception of some moduli, tensile and shear properties are degraded at both cold and elevated temperatures. Electron irradiation lowers the glass transition temperature of graphite/epoxy significantly. Property degradation of irradiated materials at the elevated temperature is associated with the reduction in Tg. It is shown that a (0) compression-strength test is the most sensitive test for exhibiting the effects of electron irradiation. Results from tests on neat resin also show that the bulk matrix is degraded after irradiation, and that the correlation between resin and composite response is good.

Herakovich, C. T.↗

Energy absorption in composite materials for crashworthy structures

Crash energy-absorption processes in composite materials have been studied as part of a research program aimed at the development of energy absorbing subfloor beams for crashworthy military helicopters. Based on extensive tests on glass/epoxy, graphite/epoxy, and Kevlar/epoxy composites, it is shown that the energy-absorption characteristics and crushing modes of composite beams are similar to those exhibited by tubular specimens of similar material and architecture. The crushing mechanisms have been determined and related to the mechanical properties of the constituent materials and specimen architecture. A simple and accurate method for predicting the energy-absorption capability of composite beams has been developed.

Farley, Gary L.↗

Strain measurements in composites subjected to compressive loading using moire interferometry

Experimental apparatus to apply a uniaxial compressive load to composite laminates and measure the resulting in-plane displacement fields using moireinterferometry were designed and built. Quasi-isotropic graphite/epoxy and graphite/PEEK laminates were subjected to near-ultimate compressive creep loadings at room temperatures. Creep loads were applied for times up to 28 hrs. Strains were calculated from the measured displacements, and compared with theoretical results.

Klein, R. J.↗

Processes for fabricating and load testing NASA scatterometer antenna assemblies

The purpose of this paper is to present the processes used to fabricate and load test the NASA Scatterometer Antenna Assemblies. The fabrication processes include layup, curing and machining of antenna components, and the bonding and assembly of the components into the final antenna configuration. The design of each antenna consists of an aluminum waveguide bonded to a sandwich structure of Nomex honeycomb core with graphite/epoxy skins. A titanium end fitting with fiberglass/epoxy transitions is bonded into one end of each antenna. Several antenna components are fabricated using a process where aluminum foil is co-cured to a composite surface. The antenna assemblies are radiographically inspected, thermally cycled, and load tested prior to shipment.

Barth, James R.↗

A continuum damage model of fatigue-induced damage in laminated composites

A model is presented which predicts the stress-strain behavior of continuous fiber reinforced laminated composites in the presence of microstructural damage. The model is based on the concept of continuum damage mechanics and uses internal state variables to characterize the various damage modes. The associated internal state variable growth laws are mathematical models of the loading history induced development of microstructural damage. The model is demonstrated by using it to predict the response of damaged AS-4/3502 graphite/epoxy laminate panels.

Harris, Charles E.↗

Measurement of impact-induced delamination buckling in composite laminates

High-velocity impact tests were performed on graphite/epoxy laminates with embedded delaminations. High-speed photography of the transversely impacted laminates shows that dynamic local buckling of the sublaminate region formed by the delamination can cause a mode-I-dominated propagation of that delamination. Simultaneous recordings of the dynamic strain histories at several locations in the buckled sublaminate region are used to measure the laminate and sublaminate responses to the impact loading. Flexural motion resulting from transverse impact is shown to reduce local buckling of the sublaminate. This buckling causes a progressive separation of the delaminated surfaces and subsequent extension of the delamination in a mode-I dominated fashion.

Grady, J. E.↗

Measurements of matrix cracking and delamination caused by impact on composite plates

Tests were performed measuring the locations and extents of delaminations and matrix crackings in 3-in. by 3-in. Fiberite T300/934 graphite/epoxy plates impacted by 1/2-in. diameter aluminum spheres. Plates with six ply orientations were tested. The impactor speeds ranged from 700 to 1300 in/sec. The plates were inspected by C-scan both before and after impact. The plates were also dissected after impact and examined visually for damage. In addition, the longitudinal and transverse tensile, compressive, and shear properties of the material were measured.

Wu, Hsi-Yung T.↗

Bearing-Bypass Loading On Bolted Composite Joints

Unexpected interaction between effects of bypass and bearing loads reported. Combined experimental and analytical study described in NASA technical memorandum conducted to investigate effects of simultaneous bearing and bypass loading on graphite/epoxy laminate. Results important in emerging technology of composites for use in wide range of applications. Includes applications in aircraft, boats, and automobiles, in which bolted connections to composites increasingly important.

Crews, John H.↗

A probabilistic approach to composite micromechanics

Probabilistic composite micromechanics methods are developed that simulate expected uncertainties in unidirectional fiber composite properties. These methods are in the form of computational procedures using Monte Carlo simulation. A graphite/epoxy unidirectional composite (ply) is studied to demonstrate fiber composite material properties at the micro level. Regression results are presented to show the relative correlation between predicted and response variables in the study.

Stock, T. A.↗

A study on the thermal and moisture influences on the free-edge delamination of laminated composites

A simple delamination analysis method is presented here. It is based on a shear-type deformation theory and includes hygrothermal effects. These environmental conditions are applied to the strain energy release rate and interlaminar shear stresses. The method is applied to mixed mode edge delamination specimens made of T300/5208 graphite/epoxy material. Residual thermal and moisture stresses significantly influenced the strain energy release rate and interlaminar stresses. Both experienced large increases when thermal conditions were added to the mechanical strains. These effects were alleviated when moisture stresses were included. Thermal effects on the interlaminar shear stress and total energy release rate were totally alleviated for the same specific moisture content. Moreover, the value of the moisture content was not significantly affected by the stacking sequence for the laminates considered.

Mahler, Mary A.↗

Stress analysis method for clearance-fit joints with bearing-bypass loads

Within a multi-fastener joint, fastener holes may be subjected to the combined effects of bearing loads and loads that bypass the hole to be reacted elsewhere in the joint. The analysis of a joint subjected to search combined bearing and bypass loads is complicated by the usual clearance between the hole and the fastener. A simple analysis method for such clearance-fit joints subjected to bearing-bypass loading has been developed in the present study. It uses an inverse formulation with a linear elastic finite-element analysis. Conditions along the bolt-hole contact arc are specified by displacement constraint equations. The present method is simple to apply and can be implemented with most general purpose finite-element programs since it does not use complicated iterative-incremental procedures. The method was used to study the effects of bearing-bypass loading on bolt-hole contact angles and local stresses. In this study, a rigid, frictionless bolt was used with a plate having the properties of a quasi-isotropic graphite/epoxy laminate. Results showed that the contact angle as well as the peak stresses around the hole and their locations were strongly influenced by the ratio of bearing and bypass loads. For single contact, tension and compression bearing-bypass loading had opposite effects on the contact angle. For some compressive bearing-bypass loads, the hole tended to close on the fastener leading to dual contact. It was shown that dual contact reduces the stress concentration at the fastener and would, therefore, increase joint strength in compression. The results illustrate the general importance of accounting for bolt-hole clearance and contact to accurately compute local bolt-hole stresses for combined bearings and bypass loading.

Naik, R. A.↗

Characterization of the bending stiffness of large space structure joints

A technique for estimating the bending stiffness of large space structure joints is developed and demonstrated for an erectable joint concept. Experimental load-deflection data from a three-point bending test was used as input to solve a closed-form expression for the joint bending stiffness which was derived from linear beam theory. Potential error sources in both the experimental and analytical procedures are identified and discussed. The bending stiffness of a mechanically preloaded erectable joint is studied at three applied moments and seven joint orientations. Using this technique, the joint bending stiffness was bounded between 6 and 17 percent of the bending stiffness of the graphite/epoxy strut member.

Wu, K. Chauncey↗

Vibration testing of impact-damaged composite laminates

A new test is described that can be used to measure changes in the vibration properties of impact damaged composite materials. Impact-induced delamination was observed to significantly affect natural frequencies of vibration and damping properties in cross-ply graphite/epoxy laminates. Natural frequencies are shown to drop by as much as half of their original value, and modal damping ratios can increase by a factor of up to eight when large amounts of damage are present. A simple finite element model of the damaged impact specimens was used to predict the effect of delamination on certain vibration properties. A comparison of the finite element calculations with the experimental measurements suggests that delamination was the dominant mechanism of flexural stiffness loss resulting from the transverse impact.

Grady, Joseph E.↗

Compression behavior of delaminated composite plates

The response of delaminated composite plates to compressive in-plane loads was investigated. The delaminated region may be either circular or elliptical, and may be located between any two plies of the laminate. For elliptical delaminations, the axes of the ellipse may be arbitrarily oriented with respect to the applied loads. A model was developed that describes the stresses, strains, and deformation of the sublaminate created by the delamination. The mathematical model is based on a two dimensional nonlinear plate theory that includes the effects of transverse shear deformation. The model takes into account thermal and moisture induced strains, transverse pressures acting on the sublaminate, and contact between the sublaminate and plate. The solution technique used is the Ritz method. A computationally efficient computer implementation of the model was developed. The code can be used to predict the nonlinear-load-strain behavior of the sublaminate including the buckling load, postbuckling behavior, and the onset of delamination growth. The accuracy of the code was evaluated by comparing the model results to benchmark analytical solutions. A series of experiments was conducted on Fiberite T300/976 graphite/epoxy laminates bonded to an aluminum honeycomb core forming a sandwich panel. Either circles or ellipses made from Teflon film were embedded in the laminates, simulating the presence of a delamination. Each specimen was loaded in compression and the strain history of the sublaminate was recorded far into the postbuckling regime. The extent of delamination growth was evaluated by C-scan examination of each specimen. The experimental data were compared to code predictions. The code was found to describe the data with reasonable accuracy. A sensitivity study examined the relative importance of various material properties, the delamination dimensions, the contact model, the transverse pressure differential, the critical strain energy release rate, and the relative growth direction on the buckling load, the postbuckling behavior, and the growth load of the sublaminate.

Peck, Scott O.↗