Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Gripper Test Assembly Status of Fabrication and Assembly Report – FY2023

The Gripper Test Assembly (GrTA) is an experimental test article designed for use at the Mechanisms Engineering Test Loop (METL) at Argonne National Laboratory (ANL). The GrTA will test mechanical components intended for use in compact in-vessel fuel handling machines (FHM) for sodium cooled fast reactors (SFR). The GrTA will test radial and thrust ball bearings, radial and thrust roller bearings, ball screws and nuts, spline shafts and ball nuts, radial spur gears, and universal joints submerged in liquid sodium at high temperatures (250°C-650°C). These components will be tested in a prototypic, full-scale gripper head and under prototypic SFR fuel handling loads. The design of the GrTA was completed in FY2022 and has progressed into fabrication and initial assembly. All custom manufactured components have been fabricated and delivered to ANL following inspection. All custom gears have been fabricated and delivered to ANL. Bearings, ball screws, and spline shafts have been purchased to allow for initial assembly in air, and sodium compatible versions have either been purchased or are in design at appropriate manufacturers. The drive motor systems that operate the various functions of the GrTA have been purchased and delivered to ANL. Instrumentation and control hardware has been purchased and delivered to ANL as well. All sodium facing components of the GrTA have been assembled and show proper fit. The three main functions of the GrTA are to raise or lower a gripper head under prototypic fuel handling loads, rotate the gripper head while carrying a fuel handling load, and extend or retract gripper jaws that lock a fuel assembly to the gripper head. All three functions have been demonstrated in air, while under no load. The GrTA project will move forward next fiscal year by completing the initial assembly, incorporating the drive system and I&C, and preparing the assembly for introduction to sodium.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

The Use of High-Density UN Fuel in Heat-Pipe Microreactors

Heat-pipe microreactors (HPMRs) are very small-scale nuclear reactors that employ heat pipes (HPs) for heat removal. HPMRs can be easily integrated with other forms of renewable energies, can be used for emergency responses to disaster relief zones, can be deployed in remote locations not connected to the grid, and can be removed from sites and replaced by new ones. HPMRs can also be used for space missions as HPs do not rely on gravity for heat transfer. Conventional fuel materials, such as uranium oxide (UO 2 ) and uranium oxycarbide (UCO), are currently considered in most existing HPMR designs, but ceramic uranium nitride (UN) fuel that has high uranium density, high thermal conductivity, and high melting point may become a better fuel candidate. Through neutronics calculations, this paper assesses the impact of using UN fuel in HPMRs with two different neutron spectra (fast and thermal) and two different fuel forms [traditional solid fuel pellets and TRi-structural-ISOtropic (TRISO) fuel compacts]. It was concluded that retrofitting HPMRs with UN fuel has the potential to reduce the initial 235 U enrichment requirement by ~3 wt% (to keep the same cycle length) or increase the cycle length (by keeping the same initial 235 U enrichment), which enables more compact and transportable HPMR core designs. However, using UN fuel decreases the control element worth [by up to 20% for the Special Purpose Reactor (SPR) and 5% for HP-MR] and is up to 80% more costly. Increasing 15 N enrichment can further decrease the initial 235 U enrichment requirement and increase the control element worth but is more costly. In conclusion, compared to fast-spectrum HPMRs fueled with solid pellet fuels, retrofitting UN fuel is more suitable for thermal-spectrum HPMRs fueled with TRISO fuel compacts, where the neutron spectrum hardening caused by using UN is less significant.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

A Gaussian process based surrogate approach for the optimization of cylindrical targets

Simulating direct-drive inertial confinement experiments presents significant computational challenges, both due to the complexity of the codes required for such simulations and the substantial computational expense associated with target design studies. Machine learning models, and in particular, surrogate models, offer a solution by replacing simulation results with a simplified approximation. In this study, we apply surrogate modeling and optimization techniques that are well established in the existing literature to one-dimensional simulation data of a new cylindrical target design containing deuterium–tritium fuel. These models predict yields without the need for expensive simulations. We find that Bayesian optimization with Gaussian process surrogates enhances sampling efficiency in low-dimensional design spaces but becomes less efficient as dimensionality increases. Nonetheless, optimization routines within two-dimensional and five-dimensional design spaces can identify designs that maximize yield, while also aligning with established physical intuition. Optimization routines, which ignore constraints on hydrodynamic instability growth, are shown to lead to unstable designs in 2D, resulting in yield loss. However, routines that utilize 1D simulations and impose constraints on the in-flight aspect ratio converge on novel cylindrical target designs that are stable against hydrodynamic instability growth in 2D and achieve high yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Cool GTL for the Conversion of Biogas to Jet Fuel

Cool GTL is a new process under development for conversion of biogas from digestors or CO2 +H2 to high quality drop in jet fuel. Cool GTL is designed to be a streamlined simplified low cost process which can be cost effective for small scale biogas applications. Cool GTL has the advantage that it uses a high activity bi-reforming catalyst, in a streamlined electric reformer design, to make the synthesis gas for a high conversion slurry fischer Tropsch process followed by a trailing wax cracking reactor. In this way high quality jet fuel can be directly produced. Recent experimental test data will be presented showing product quality. The life cycle analysis LCA will also be presented as well.

09 BIOMASS FUELS↗
DOE OSTI2025

Conjugate Heat Transfer Modeling of Salt-Filled Fuel Pins for Stable Salt Reactor Safety Analysis

The Stable Salt Reactor (SSR) combines the proven structural design of light water reactor fuel assemblies with the inherent safety and fuel-cycle advantages of molten salt technology. In its fast reactor configuration, the SSR utilizes recycled nuclear waste as fuel, sealed within narrow salt-filled fuel pins and cooled by a surrounding liquid salt coolant. Reliable transfer of heat from the molten fuel salt through the cladding to the external coolant is essential for both reactor safety and performance. This work investigates conjugate heat transfer (CHT) in the SSR’s salt-filled fuel pins using NekRS, a high-fidelity spectral element computational fluid dynamics (CFD) solver. The analyses capture internal natural convection within the molten fuel salt and external forced convection in the coolant, under steady-state and transient operating conditions. Parametric studies evaluate how variations in reactor power and coolant flow rate influence heat transfer distributions and system response. The high-fidelity CFD results are time-averaged and post-processed for direct comparison with moderate-fidelity Reynolds-averaged Navier–Stokes (RANS) models, and for the development of reduced-order models within the SAM system code. These validated models support fast-running safety analyses of normal and off-normal transients, improving predictive capability for key safety margins. By integrating advanced CFD with system-level safety tools, this study strengthens the modeling framework for SSR design, reduces uncertainty in molten salt CHT simulations, and accelerates the engineering and licensing of next-generation nuclear reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Computational Modeling of Graphite Degradation due to Molten Salt Infiltration and Wear

Molten-salt reactors (MSRs) represent a promising next-generation reactor design, with graphite serving as a moderator and/or reflector in several designs. However, due to limited experimental data and operational experience, a technical understanding of the structural integrity of graphite in molten salt environments remains incomplete. This report presents a modeling-based evaluation of graphite degradation in MSR environments, focusing on the effects of salt infiltration in fuel salt-based designs and surface wear in pebble bed reactor designs. The objective of this study is to enhance understanding of the structural integrity challenges posed by these degradation mechanisms and to provide a framework for assessing graphite behavior in MSRs. The first part of the report investigates the phenomenon of molten salt infiltration into graphite. This infiltration occurs when molten salt permeates the interconnected pore structure of the graphite moderator, driven by factors such as pressure differentials and the physical properties of both the salt and graphite. The infiltration process is influenced by characteristics of the pore structure, viscosity of the molten salt, and the interfacial energies between the graphite, salt, and the atmosphere within the graphite pore. Utilizing a coupled multiphysics modeling approach with Grizzly software, the study evaluates the stress induced by internal heat sources due to infiltration, which can lead to structural concerns. This evaluation is crucial for understanding how infiltration affects the mechanical integrity of graphite components in MSRs. The study considers the Molten-Salt Reactor Experiment (MSRE) graphite stringer geometry due to the availability of relevant data. Through detailed finite element analysis, the study examines stress distributions at varying infiltration percentages, revealing that stress levels increase with higher amounts of infiltration. Rare-event simulations, using the parallel subset simulation (PSS) framework, further quantify the failure probabilities under input uncertainties, with a user-specified failure metric. The PSS framework also identifies critical input parameters that significantly affect the stress values, including infiltration amount, thermal conductivity, and power density. Additionally, considering realistic reactor scenarios, the analysis was performed to account for the combined effects of radiation and infiltration, and modeling strategies on how to analyze new reactor designs or new graphite grades are discussed. The second part of the report focuses on wear mechanisms in pebble bed-based MSRs. As graphite fuel pebbles interact with the graphite reflector block, wear can result in material loss and the formation of surface defects, which may act as stress concentrators. A similar multiphysics modeling framework is employed to assess the impact of wear on the structural integrity of graphite components. This study considers a generic fluoride-cooled high-temperature reactor (gFHR) design due to the availability of comprehensive data. Worst-case scenario dimensions of the reflector blocks were analyzed under thermal and radiation conditions. Subsequently, wear in the form of idealized pits and grooves is modeled on the inner surface of the graphite block, with the maximum stress from previous simulations. The simulations show that groove-type defects are more detrimental than pits, leading to higher stress concentrations. Considering worst-case simulation scenarios and experimental wear rates, it was determined that the formation of a surface defect critical enough to affect the stress may not be possible in a gFHR design. Overall, the findings of this research contribute to the development of robust modeling tools for predicting graphite behavior under various operational conditions in MSRs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Ceramic Composite Inert Matrix Fuel Forms in High-Temperature Gas-Cooled Microreactors

Here, this work optimizes micro-prismatic high-temperature gas reactor (HTGR) designs to reduce the energy-normalized mass of spent nuclear fuel (SNF) and high-level waste (HLW) produced. The optimization was performed for the current graphite moderator and an inert matrix fuel (IMF) concept employing different composite moderators in a prismatic design architecture. The fuel matrix is magnesium oxide (MgO) with entrained tristructural-isotropic (TRISO) fuel. The moderator materials, including beryllium oxide (MgO-BeO) and beryllium (MgO-Be) at 40 vol % loading and yttrium hydride (MgO-YH x=1.9 ) and zirconium hydride (MgO-ZrH x=1.9 ) at 15 vol % loading, were entrained within the MgO host matrix. A generic graphite micro-prismatic HTGR is used as the baseline point design where the external dimensions are held constant. The composite moderator designs use 19.9% enriched uranium nitride TRISO fuel and hexagonal assemblies. For each IMF concept, an optimization study was performed to maximize the discharge burnup of the fuel by varying the TRISO packing fraction and the lattice pitch of the assemblies. The mass of SNF and HLW, other waste metrics, fuel cost, environmental impact metrics, and the activity of the SNF and HLW at 100 years and 100 000 years were calculated for the optimized IMF and graphite reference designs. The IMF results were subsequently compared to those of the graphite reference and the values for a light water reactor (LWR) and a small modular LWR. For the SNF and HLW, all the IMF concepts and the graphite reference produced less waste compared to the traditional LWR designs. However, the IMF concepts outperformed the graphite reference regarding the mass of SNF and HLW. For the other waste metrics, the IMF concepts showed reductions in fuel cost with improved environmental metrics relative to the graphite reference. Overall, the IMF concepts significantly reduced the SNF and HLW produced per unit of energy generated compared to traditional LWR designs.

TRISO↗
DOE OSTI2023

Transition Core Modeling for Extended Enrichment & Accident-Tolerant Fuels Using Polaris/PARCS

Commercial light water reactor (LWR) operators and fuel vendors are currently interested in increasing the low-enriched uranium (LEU) fuel enrichments from the current limit of 5.0 $^w/_o$ $^{235}U$ up to 10 $^ w/_o$ $^{235}U$ (referred to as "LEU+") in their current fleets; they are also interested in using accident-tolerant fuel (ATF) with both LEU and LEU+ fuel. This report aims to identify modeling challenges and accuracy concerns in transition core analysis using the SCALE Polaris lattice physics code and U.S. Nuclear Regulatory Commission core simulator PARCS. At the time this study was started, no publicly available LEU+ core designs existed for boiling water reactor (BWR) or pressurized water reactor (PWR) systems. Therefore, fuel lattices were shuffled within a multi-assembly model to mimic neutronically challenging lattice combinations seen in transition cores, such as a fresh LEU+ lattice next to depleted LEU lattices. In addition to multi-assembly models, whole-core BWR transition core calculations were performed for ATF and LEU+ fuel using an existing Hatch-1 Cycle 3 core model. A whole-core BWR model was chosen due to the more heterogeneous core designs compared to those for a PWR core. Since the original core is an old checkerboard core design and no core or fuel design optimization was performed for the modeled fuel types, these core calculations were intended only to provide: (1) Comparisons of core characteristics of interest, such as the pin power distributions and peaking factors, Doppler temperature coefficients (DTCs), and control blade worths (CBWs) under challenging core designs, (2) Identification of reactor physics challenges in modeling LEU+ and ATF cores, and (3) A stress test for the Polaris/PARCS two-step modeling approach, including characterization of the relative accuracy for predicting characteristics of interest such as pin power distributions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Architecture-Based Control of Temperature Gradient-Driven Water Transport in Polymer Electrolyte Fuel Cells

Temperature gradients can move water within the porous media of a polymer electrolyte fuel cell through phase-change-induced (PCI) flow. It is critical to understand PCI flow so that control and distribution of water within a fuel cell can be accomplished. This work investigates the role of architecture, specifically anode land width, on overall cell water content and distribution in the through-plane direction. A specially-designed 4.8 cm 2 fuel cell with precise thermal boundary conditions was imaged with neutrons using two different anode flow field configurations. A new, non-dimensional thermal transport number was developed which quantifies the relative influence of PCI flow on cell water transport. It was found that anode lands larger than the cathode lands cause large thermal gradients that instigate net water flux from the cathode to the anode. An asymmetric configuration with larger anode lands was found to have large changes in water content that were strongly sensitive to cell operating conditions. The thermal transport number developed here enables deduction of the net flux condition based on operating conditions and architecture. This approach enables design of high-performance systems with balanced water management.

25 ENERGY STORAGE↗
DOE OSTI2021

ECAR-5021 Source Term Estimates for SCO Micro-Reactor Designs

The purpose of this document is to provide source term estimates and the associated technical basis for Strategic Capabilities Office (SCO) microreactor designs that use TRISO fuel. This estimate can be used for relevant environmental and safety analyses that will be done as part of the project for all of the selected suppliers for a safety design strategy. This is a combined quantitative and qualitative analysis.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Design of additively manufactured methanol conversion reactor for high throughput production

Additively manufactured methanol conversion reactor was designed and fabricated for high throughput fuel production while capturing carbon dioxide. Here, the reactor designed is part of large effort in integrating electrolyzer and catalytic reactor system. Processing in fabricating the steel, titanium, and nickel alloy reactors were optimized to improve the catalyst deposition process and reaction efficiency. Microstructure of the additively manufactured reactors were characterized. General design is utilized to improve the performance of the reactor while exploring the benefit of freeform in additive manufacturing.

08 HYDROGEN↗
DOE OSTI2023

Numerical Optimization of Spray-Guided Spark Assistance for Cold Idle Operation in a Heavy-Duty Gasoline Compression Ignition Engine

This article describes the results of a response surface model (RSM)-based numerical optimization campaign for spray-guided spark assistance at cold operations in a heavy-duty gasoline compression ignition (GCI) engine. On the basis of an earlier work on spark-assisted GCI cold combustion, a space-filling design of experiments (DoE) method was first undertaken to investigate a multitude of hardware design variables and engine operating parameters. The main design variables included the number of injector nozzles, fuel split quantities and injection timings, and spark timing. The objective variables were engine combustion efficiency (ŋ c ), maximum pressure rise rate (MPRR), and engine-out nitrogen oxide (NO x ) emissions. A total of 150 design candidates were automatically generated using the Sobol sequence method provided by the commercial software package, CAESES. Then, closed-cycle computational fluid dynamic (CFD) spark-assisted GCI simulations under cold idling operations were performed. The outcomes from the CFD-DoE design campaign were utilized to construct high-fidelity RSMs that allowed for further design optimization of the spark plug- and fuel injector-related design variables, along with fuel injection strategy parameters. A merit function with respect to objective variables was formulated with an appropriate weight assignment on each objective variable. Finally, the best design candidate was identified from the RSM-based optimization process and further validated in the CFD analysis. The best design candidate showed the potential to significantly improve combustion efficiency (ŋ c > 90%) over the baseline at cold idle while satisfying MPRR and NOx emissions constraints (MPRR < 5 bar/CAD and NO x < 4.5 g/kWh).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Irradiation performance of a U-7Mo in Al-Si matrix dispersion full-size fuel plate assembly

The Korea Atomic Energy Research Institute (KAERI) is leading the Ki-Jang Research Reactor (KJRR) project with the intent to develop a new reactor for medical isotope production and other nuclear research purposes. The KJRR core is designed to use high density fuel system where uranium alloyed with 7 wt% molybdenum (U-7Mo) particles are dispersed in a matrix of aluminum alloyed with 5 wt% silicon (Al-5Si) and clad in aluminum alloy 6061 (Al-6061) to form fuel plates. KAERI developed a fabrication facility to construct KJRR fuel assemblies and partnered with the Idaho National Laboratory (INL) to irradiate a full-size fuel assembly, with 21 total fuel plates, in the Advanced Test Reactor (ATR). Irradiation testing and subsequent Post Irradiation Exam (PIE) campaigns were performed successfully over a multi-year project. Monte Carlo neutronic calculations, coupling with a depletion code, were performed based on ATR’s as-run power history which showed that the highest power plate (plate 20) reached 83.1 % end-of-life (EOL) local burnup based on initial 235 U content. Additionally, finite element thermal modeling was performed based as-run power history which showed a beginning-of-life (BOL) peak local heat flux of 184 W/cm 2 . No anomalous fuel performance was observed during the irradiation and target test conditions were achieved. PIE showed favorable performance of the fuel assembly regarding all important phenomena. This paper describes the KJRR fuel assembly irradiation conditions and PIE data to support the conclusion that it performed well, without evidence of unexpected or problematic fuel performance, within an irradiation test designed to bound the KJRR design environment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

FCET Solid Oxide Fuel Cell Testing and Development: CRADA 526 [Abstract only]

The purpose of the proposed project is for PNNL to test the performance of prototype solid oxide fuel cells (SOFCs) created by FCET. Such testing will provide FCET with independent performance data that can be communicated to potential clients and/or investors. Additionally, PNNL will collaborate with FCET on design changes to improve fuel cell performance. Intellectual property developed in this way will benefit FCET with improved products to market, and PNNL through royalty revenue. The key technology held by FCET is a process to deposit extremely thin layers of oxide materials, from 10-50 nm in thickness. The range of possible materials that can be deposited with their method is broad, but this project will focus on the yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight YSZ membranes have been a long-sought target in SOFC research. The thinner the YSZ, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). 10-50 nm would be a major step change in YSZ thickness from the state of the art. PNNL can team with FCET on future R&D projects and push this technology forward to improve energy efficiency and reduce carbon emissions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

AGR-5/6/7 Irradiation Disassembly and Metrology First Look

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program was established to perform research and development on tristructural isotropic (TRISO)-coated particle fuel to support deployment of high-temperature gas-cooled reactors (HTGRs), which are graphite-moderated nuclear reactors cooled with helium. This work continues as part of the Advanced Reactor Technologies (ART) TRISO Fuel Program. The overarching program goal is to provide a baseline fuel qualification data set to support licensing, deployment, and operation of HTGRs in the United States. To achieve these goals, the program includes fuel fabrication, irradiations of TRISO fuels and high-temperature materials (e.g., graphite), safety testing and post-irradiation examination (PIE), fuel performance modeling, and fission product transport and source term determination. The ART AGR program has conducted four distinct fuel irradiation experiments in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). The first of these irradiation tests, designated AGR-1, began in ATR in December of 2006 and ended in November 2009. This experiment was primarily to act as a shakedown test of the multi-capsule test train design and to provide early data on fuel performance that would be used in fuel fabrication process development. AGR-1 fuel kernels were produced on an engineering scale, but the TRISO coatings and cylindrical fuel compacts were fabricated on a laboratory scale. The AGR-1 PIE was completed and the final report was published in 2015. The second irradiation test, AGR-2, started in ATR in June 2010 and ended in October 2013. The AGR-2 irradiation test was designed to provide fuel performance data for coated particles fabricated on an engineering-scale pilot line using a coater with an internal chamber diameter of 150 mm (6 in.). The final PIE report was published in 2021. AGR-3/4, a single irradiation that combined what were originally conceived as the third and fourth tests, was to support the refinement of fission product transport models and to assess the effects of sweep gas impurities on fuel performance and fission product transport. PIE of the AGR-3/4 experiment is still in progress as of this writing. The subject of this report is AGR-5/6/7, the final qualification test of AGR TRISO fuel made entirely at the engineering scale.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Preliminary Analysis of Advanced Reactors Storage, Transportation, and Disposal

Based on the higher interest in Advanced Reactor (AR) deployment (e.g., ARDP[1]) for potential new fuel cycles, the Spent Fuel & Waste Science and Technology (SFWST) Program has begun to evaluate the possible implications of long-term management and final disposition of potential Advance Reactor spent nuclear fuels (SNF) that would be generated in potential advanced reactors. Safely managing and dispositioning the potential future AR SNF, and any other associated radioactive wastes, is the primary focus of this initial preliminary assessment of those. This paper summarizes the efforts by the Spent Fuel & Waste Science and Technology (SFWST) in evaluating characteristics and packaging options for advanced reactor spent nuclear fuel forms. The fuel forms were categorized into three types: (1) tristructural isotropic (TRISO), (2) metallic, and (3) fuel salt. This work emphasized TRISO and metallic SNF and waste streams because of the near-term anticipated operation of the Xe-100 and the Natrium reactors as advanced-reactor demonstrations. Preliminary information for the spent-fuel salts discharged from molten-salt reactors (MSRs) is also examined to provide a baseline for future efforts. All calculations and assumptions used publicly available information. The following characteristics are calculated or estimated for use in the preliminary assessments: SNF volume and mass, radiation/activity levels through time, thermal conditions through time, potential radionuclide source terms, chemical interactions and evolutions, disposal inventories, and waste-form lifetime. Using those characteristics, calculations to determine the applicability of existing canister designs were performed. These evaluations included geometric (e.g., dimension, volume) and mass/weight considerations, known operational approaches and loading procedures, physical and chemical considerations/conditions for storage environments, as-loaded radiation, thermal, and criticality analyses to identify constraints for storage, transportation, and disposal. The paper also includes a literature review and analysis on the storage, transportation, and disposal evaluations and experiences from reactors with similar fuel forms. Advanced-reactor vendors cite past experiences with Fort St. Vrain for TRISO and the Experimental Breeder Reactor II (EBR-II) for metallics that have major influences on fuel design. Finally, the paper includes preliminary concepts of operation for advanced-reactor SNF. This encompasses storage, transportation, potential treatment, and disposal activities from both a per-canister and systems-integration perspective.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

ROADRUNNER MiniFuel Experiment: Irradiation Target Design and Sample Characterization

High-density uranium nitride (UN) is a fuel candidate for several advanced nuclear reactor designs currently under development. Because there are limited UN performance data relative to fuel fabrication impurity and density variation, an irradiation campaign has been developed as part of a collaborative effort among the University of Texas at San Antonio (UTSA), Westinghouse Electric Company, Oak Ridge National Laboratory (ORNL), and Los Alamos National Laboratory (LANL) under the Nuclear Science User Facilities program. This project, entitled ROADRUNNER, or Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments, aimsto support UN fuel qualification for advanced reactors by investigating the impact of density and impurity variations on UN performance as a function of irradiation temperature and burnup. The MiniFuel experiment vehicle developed by ORNL, which leverages the High Flux Isotope Reactor, was selected to perform this accelerated separate-effects irradiation testing. The experiment test matrix consists of six MiniFuel targets containing miniature UN fuel disks, and targets three distinct burnup levels (37.5, 60, and 75 MWd/kg U) and three distinct temperatures (600, 900, and 1200°C). Neutronics and thermal analyses were performed to determine the experimental parameters needed to meet the desired irradiation conditions and to predict the experiment components temperatures. UN pellets were fabricated at LANL with tightly controlled parameters to produce specimens with three distinct densities and three levels of carbon content. The pellets were then thinned down by UTSA to the experiment-required thickness. The pre-characterization of the specimens includes density measurements, carbon and oxygen contents, microstructure analysis, and x-ray computed tomography. The selected specimens will be assembled into the MiniFuel experiment, and the first ROADRUNNER MiniFuel targets are intended for HFIR insertion during the Fall of 2024. After irradiation, the targets will be shipped to ORNL’s hot cell facility for disassembly. The post-irradiation examination on the fuel specimens includes fission gas release measurements, visual inspection, fuel swelling measurements, gamma spectroscopy, and microstructure analysis. The data collected post-irradiation will be used to develop fuel performance models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Design of an Out-Of-Pile Experimental Facility to Demonstrate the Feasibility of In Situ Thermal Conductivity Measurements of Nuclear Fuels Under Irradiation

There is substantial merit in quantifying nuclear fuel performance under irradiation. At Oak Ridge National Laboratory (ORNL), the MiniFuel irradiation platform has become the primary test vehicle for conducting separate-effects fuel performance irradiation experiments. The MiniFuel experiment is a passively controlled capsule design deployed in the High Flux Isotope Reactor (HFIR) through which fuel performance data is collected post-irradiation. Separate effects fuels irradiation capabilities are being expanded at ORNL by developing instrumented capsule designs that aim to capture fuel performance phenomena in-situ. One such capsule will specifically target fuel specimen thermal conductivity changes as a function of fuel burnup. Due to the complexity of making this measurement on nuclear fuel in-pile, this paper describes the necessary out-of-pile testing conducted on the thermal conductivity capsule (TCC) design. The measurement is ascertained via a thermopile system with heat transferred unidirectionally through a surrogate fuel specimen sandwiched between two conductive materials. The capsules investigated in this study are representative of the in-pile design, with the primary departure from irradiation conditions being the distribution of heat generation within the capsule. In the out-of-pile experiment, an external heater was used to drive heat through the conductive slug materials and into the specimen. This paper expounds the design of the out-of-pile experimental system and the thermal conductivity measurement technique. Predictive models used to determine the sensitivity of the measurement to variables governing thermal contact conductance between the specimen and slug materials and to predict experimental results are also described. Data from the out-of-pile experiment will be used to validate the readiness of the design for insertion into HFIR for irradiation.

Parker, Trevor [ORNL]↗