Results for “Entry Systems and Modeling” — Page 35

NASA NTRSDate not supplied

Mars 2020 Reconstructed Aerothermal Environments and Design Margins

The Mars 2020 aeroshell's thermal protection system was nearly identical to the Mars Science Laboratory system that successfully completed its mission for the Curiosity rover's landing in 2012. It was predicted that, like Mars Science Laboratory, the Mars 2020 heatshield would experience boundary layer transition and that the thermal protection system would provide sufficient material thickness margins against the aerothermal environments, even after adding radiative heating that was not included for Mars Science Laboratory. The Mars 2020 flight instrumentation suite included heatshield sensors similar to Mars Science Laboratory and new backshell measurements. A full set of surface pressure and in-depth temperature data were collected during atmospheric entry. This paper provides an initial analysis of the flight data and focuses on the reconstructed total surface heat flux inferred from the measured temperatures. Turbulent boundary layer conditions again were observed on the Mars 2020 heatshield, and the temperatures at all eleven heatshield and six backshell thermocouple in-depth sensor locations were well within system capabilities due to favorable entry conditions and conservative uncertainties. New computational fluid dynamics results on the reconstructed entry trajectory are compared to the measured surface pressures and reconstructed total heat fluxes. The predicted heatshield surface pressures at six locations match the data qualitatively and quantitatively well, as expected. Smooth-wall laminar heating predictions prior to boundary layer transition fall above the reconstructed heating on the heatshield. After the observed boundary layer transition time, total heat flux based on algebraic turbulence model calculations generally match the heat flux trends relative to one another. The convective heat flux was predicted to constitute the majority of the total heating. On the backshell, smooth-wall laminar total heat flux predictions generally exceed the reconstructed total heating at six locations. At each of these locations, it is estimated that radiative heating provided almost all of the total heating. The Mars 2020 as-flown aerothermal environments were well below the design levels for all measurement locations due to conservative design assumptions and a stressing design trajectory.

Mars 2020↗

NASA NTRSDate not supplied

Mars 2020 Reconstructed Aerothermal Environments and Design Margins

The Mars 2020 aeroshell's thermal protection system was nearly identical to the Mars Science Laboratory system that successfully completed its mission for the Curiosity rover's landing in 2012. It was predicted that, like Mars Science Laboratory, the Mars 2020 heatshield would experience boundary layer transition and that the thermal protection system would provide sufficient material thickness margins against the aerothermal environments, even after adding radiative heating that was not included for Mars Science Laboratory. The Mars 2020 flight instrumentation suite included heatshield sensors similar to Mars Science Laboratory and new backshell measurements. A full set of surface pressure and in-depth temperature data were collected during atmospheric entry. This paper provides an initial analysis of the flight data and focuses on the reconstructed total surface heat flux inferred from the measured temperatures. Turbulent boundary layer conditions again were observed on the Mars 2020 heatshield, and the temperatures at all eleven heatshield and six backshell thermocouple in-depth sensor locations were well within system capabilities due to favorable entry conditions and conservative uncertainties. New computational fluid dynamics results on the reconstructed entry trajectory are compared to the measured surface pressures and reconstructed total heat fluxes. The predicted heatshield surface pressures at six locations match the data qualitatively and quantitatively well, as expected. Smooth-wall laminar heating predictions prior to boundary layer transition fall above the reconstructed heating on the heatshield. After the observed boundary layer transition time, total heat flux based on algebraic turbulence model calculations generally match the heat flux trends relative to one another. The convective heat flux was predicted to constitute the majority of the total heating. On the backshell, smooth-wall laminar total heat flux predictions generally exceed the reconstructed total heating at six locations. At each of these locations, it is estimated that radiative heating provided almost all of the total heating. The Mars 2020 as-flown aerothermal environments were well below the design levels for all measurement locations due to conservative design assumptions and a stressing design trajectory.

Mars 2020↗

NASA NTRS2024

Recipes for Forming a Carbon–Rich Giant Planet

The exploration of carbon-to-oxygen ratios has yielded intriguing insights into the composition of close-in giant exoplanets, giving rise to a distinct classification: carbon-rich planets, characterized by a carbon–to–oxygen ratio ≥ 1 in their atmospheres, as opposed to giant planets exhibiting carbon–to–oxygen ratios close to the protosolar value. In contrast, despite numerous space missions dispatched to the outer solar system and the proximity of Jupiter, Saturn, Uranus, and Neptune, our understanding of the carbon-to-oxygen ratio in these giants remains notably deficient. Determining this ratio is crucial as it serves as a marker linking a planet’s volatile composition directly to its formation region within the disk. This article provides an overview of the current understanding of the carbon-to-oxygen ratio in the four gas giants of our solar system and explores why there is yet no definitive dismissal of the possibility that Jupiter, Saturn, Uranus, or Neptune could be considered carbon-rich planets. Additionally, we delve into the three primary formation scenarios proposed in existing literature to account for a bulk carbon-to-oxygen ratio ≥ 1 in a giant planet. A significant challenge lies in accurately inferring the bulk carbon-to-oxygen ratio of our solar system’s gas giants. Retrieval methods involve integrating in situ measurements from entry probes equipped with mass spectrometers and remote sensing observations conducted at microwave wavelengths by orbiters. However, these methods fall short of fully discerning the deep carbon-to-oxygen abundance in the gas giants due to their limited probing depth, typically within the 10–100 bar range. To complement these direct measurements, indirect determinations rely on understanding the vertical distribution of atmospheric carbon monoxide in conjunction with thermochemical models. These models aid in evaluating the deep oxygen abundance in the gas giants, providing valuable insights into their overall composition.

Protosolar nebula↗

NASA NTRS2011

Current Status on Radiation Modeling for the Hayabusa Re-entry

On June 13, 2010 the Japanese Hayabusa capsule performed its reentry into the Earths atmosphere over Australia after a seven year journey to the asteroid Itokawa. The reentry was studied by numerous imaging and spectroscopic instruments onboard NASA's DC-8 Airborne Laboratory and from three sites on the ground, in order to measure surface and plasma radiation generated by the Hayabusa Sample Return Capsule (SRC). Post flight, the flow solutions were recomputed to include the whole flow field around the capsule at 11 points along the reentry trajectory using updated trajectory information. Again, material response was taken into account to obtain most reliable surface temperature information. These data will be used to compute thermal radiation of the glowing heat shield and plasma radiation by the shock/post-shock layer system to support analysis of the experimental observation data. For this purpose, lines of sight data are being extracted from the flow field volume grids and plasma radiation will be computed using NEQAIR [4] which is a line-by-line spectroscopic code with one-dimensional transport of radiation intensity. The procedures being used were already successfully applied to the analysis of the observation of the Stardust reentry [5].

Winter, Michael W.↗

NASA NTRSDate not supplied

Numerical Evaluation of Entry System Trajectory Control via Active Porosity Control of Transpiration Cooled Thermal Protection System

As space exploration expands, atmospheric descent requirements will tighten to improve landing accuracy to areas of interest. One way to meet higher landing accuracy requirements is by increasing vehicle maneuverability. This study explores the concept of manipulating a transpiration cooling scheme for entry capsules that could provide both active aerodynamic control as well as thermal protection for external surfaces. Numerical methods of fluid dynamics and heat transfer are presented to study the effectiveness of the concept in both thermal protection and entry vehicle attitude control. This effort works through development of an entry vehicle model at aeromaneuvering conditions with designated boundary activated for effects of transpiration cooling. Preliminary results show calculated values of heat flux and aerodynamic forces as a function of varying transpiration cooling flow rates. This contributes evidence of asymmetric cooling utilization as an additional mechanism for vehicle attitude control.

Caroline Anderson↗

NASA NTRS2002

Transition Documentation on a Three-Element High-Lift Configuration at High Reynolds Numbers: Analysis

A 2-D high-lift system experiment was conducted in August of 1996 in the Low Turbulence Pressure Tunnel at NASA Langley Research Center, Hampton, VA. The purpose of the experiment was to obtain transition measurements on a three element high-lift system for CFD code validation studies. A transition database has been created using the data from this experiment. The present report contains the analysis of the surface hot film data in terms of the transition locations on the three elements. It also includes relevant information regarding the pressure loads and distributions and the wakes behind the model to aid in the interpretation of the transition data. For some of the configurations the current pressure data has been compared with previous wind tunnel entries of the same model. The methodology used to determine the regions of transitional flow is outlined and each configuration tested has been analyzed. A discussion of interference effects, repeatability, and three-dimensional effects on the data is included.

Bertelrud, Arild↗

NASA NTRSDate not supplied

OVERFLOW Analysis of Supersonic Retropropulsion Testing on a Blunt Mars Entry Vehicle Concept

Supersonic retropropulsion (SRP) flow over a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) blunt-body vehicle was simulated using the Overflow Computational Fluid Dynamics (CFD) solver. Two nozzle configurations were tested (1E and 1F) as a subset of the seven total configurations in the Descent System Study (DSS) testing campaign. A generalized, Adaptive Mesh Refinement (AMR) shock capturing and plume refinement technique was developed and calibrated for producing automatic and unique grid systems optimized for any given testing condition. Solution independence from grid resolution was determined by successively increasing grid refinement until asymptotic convergence of the mean aerodynamic loads was observed. Overflow Reynolds-averaged Navier-Stokes (RANS) solutions produced realistic SRP flow phenomena, including Mach disk normal shocks contained in high-thrust plumes and bow shock triple-points. Solutions for the 1E nozzle configuration were steady. Conversely, a subset of the 1F test conditions were unsteady and exhibited periodic, non-sinusoidal expansions and contractions of the streamwise-oriented plume, resulting in unsteady aerodynamic loads on the vehicle. Initial investigations into the effect of turbulence modeling fidelity demonstrated significant differences between the aerodynamic loads simulated with RANS and Detached Eddy Simulation (DES). Multiple flow mechanisms were identified as root causes of these differences, including bow shock shape augmentation and reduced entrainment due to reduced turbulence in the DES simulations. Initial comparisons of pitching moment control authority and aerodynamic drag performance between the tested nozzle configurations demonstrated that the 1E configuration may be more advantageous for the Mars Entry, Descent, and Landing (EDL) task.

Supersonic Retropropulsion↗

NASA NTRSDate not supplied

OVERFLOW Analysis of Supersonic Retropropulsion Testing on a Blunt Mars Entry Vehicle Concept

Supersonic retropropulsion (SRP) flow over a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) blunt-body vehicle was simulated using the Overflow Computational Fluid Dynamics (CFD) solver. Two nozzle configurations were tested (1E and 1F) as a subset of the seven total configurations in the Descent System Study (DSS) testing campaign. A generalized, Adaptive Mesh Refinement (AMR) shock capturing and plume refinement technique was developed and calibrated for producing automatic and unique grid systems optimized for any given testing condition. Solution independence from grid resolution was determined by successively increasing grid refinement until asymptotic convergence of the mean aerodynamic loads was observed. Overflow Reynolds-averaged Navier-Stokes (RANS) solutions produced realistic SRP flow phenomena, including Mach disk normal shocks contained in high-thrust plumes and bow shock triple-points. Solutions for the 1E nozzle configuration were steady. Conversely, a subset of the 1F test conditions were unsteady and exhibited periodic, non-sinusoidal expansions and contractions of the streamwise-oriented plume, resulting in unsteady aerodynamic loads on the vehicle. Initial investigations into the effect of turbulence modeling fidelity demonstrated significant differences between the aerodynamic loads simulated with RANS and Detached Eddy Simulation (DES). Multiple flow mechanisms were identified as root causes of these differences, including bow shock shape augmentation and reduced entrainment due to reduced turbulence in the DES simulations. Initial comparisons of pitching moment control authority and aerodynamic drag performance between the tested nozzle configurations demonstrated that the 1E configuration may be more advantageous for the Mars Entry, Descent, and Landing (EDL) task.

Supersonic Retropropulsion↗

NASA NTRS2005

A Proposed Role of Aeroelasticity in NASA's New Exploration Vision

On 14 January 2004, NASA received a mandate to return astronauts to the Moon, evolve a sustained presence there, then head out into the solar system to Mars and perhaps beyond. This new space exploration initiative directs NASA to develop human and robotic technologies that can deliver payloads larger than Apollo to the Moon, to Mars, and bring astronauts and samples safely back to Earth at costs much lower than Apollo. These challenges require creative aerospace systems. On proposed technology for safely delivering payloads to the surface of Mars and returning samples to Earth involves deployed flexible and inflatable decelerators for atmospheric entry. Because inflatable decelerators provide the entry vehicle more drag surface area at smaller mass than traditional ablative devices, this class of decelerators can potentially accomodate larger mass payloads. The flexibility of these lightweight aeroshells can pose both vehicle and aeroelastic stability problems if not properly designed for the expected flight regimes. Computational tools need to be developed for modelling the large and nonlinear deformations of these highly flexible structures. Unlike wind tunnel testing, an integrated and efficient aeroelastic analysis tool can explore the entire flight environment. This paper will provide some background on flexible deployable decelerators, survey the current state of technology and outline the proposed development of an aeroelastic analysis and capability.

Bartels, Robert E.↗

NASA NTRS2016

Post-Flight Analysis of GPSR Performance During Orion Exploration Flight Test 1

On 5 December 2014, the first test flight of the Orion Multi-Purpose Crew Vehicle executed a unique and challenging flight profile including an elevated re-entry velocity and steeper flight path angle to envelope lunar re-entry conditions. A new navigation system including a single frequency (L1) GPS receiver was evaluated for use as part of the redundant navigation system required for human space flight. The single frequency receiver was challenged by a highly dynamic flight environment including flight above low Earth orbit, as well as single frequency operation with ionospheric delay present. This paper presents a brief description of the GPS navigation system, an independent analysis of flight telemetry data, and evaluation of the GPSR performance, including evaluation of the ionospheric model employed to supplement the single frequency receiver. Lessons learned and potential improvements will be discussed.

Barker, Lee↗

NASA NTRS1976

Applications Study of Aero-Maneuvering Orbit-to-Orbit Shuttle (AMOOS), Executive Summary

Preliminary designs and the supporting analysis for both the Aeromaneuvering Orbit-to-Orbit Shuttle (AMOOS) and the Aeromaneuvering Recovery System (AMRS) are presented. The AMOOS design is shown to yield from twice to almost three times the high energy, round-trip payloads as a purely propulsive vehicle of the same weight. Typically AMOOS can perform a crew rotation mission to equatorial geosynchronous orbit in one space shuttle launch. The flight test program analysis modeled parameters such as maximum dynamic pressure, heating rates, guidance, stability and recovery. Two model flight schedules were developed, one consisting of four flights and the other of two flights. The former is considered a very low risk, high information return program whereas the latter is a minimal cost program consistent with reasonable data returns and chance of success. The AMOOS and AMRS guidance scheme developed using linear regulator theory proved a precise and accurate guidance scheme. Both it and a classical linear system's based scheme were evaluated using 65 simulated trajectories in which the position in the entry corridor and the atmospheric density were varied randomly.

White, J.↗

NASA NTRSDate not supplied

High-Enthalpy Testing to Validate Simulation of an Aerosol Capture Probe

AERACEPT (Aerosol Rapid Analysis Combined Entry Probe/sonde Technology) is a developing technology enabling in-situ aerosol particle sampling and analysis in a small spacecraft mission envelope. It integrates a passive aerosol sample collection system into a probe’s thermal protection system (TPS) to remove the need for heat shield separation and active descent control (parachutes, gliders, etc.). AERACEPT is being validated against the requirements of the Nephele mission concept, which targets the middle and lower Venus cloud layers. The proposed technology employs 3D Carbon-Carbon (3D-CC) at the probe’s nose to withstand the extreme environments encountered in a Venus entry without producing pyrolysis gases that would contaminate the mission sample collection. Any shape change of this 3D-CC sample inlet will affect airflow through the sampling system, thereby impacting aerosol sample collection bias and efficiency. Accurate prediction of the nose’s material response during entry is there-fore of fundamental importance to the development and practical use of this technology. As a result, the AERACEPT project is planning a test campaign in the newly built PlasmatronX facility with a novel “Open Iso-Q” test article to validate state-of-the-art material response tools for a simulated Venus entry. The PlasmatronX is a 350 kW inductively-coupled plasma facility developed and run by the Center for Hypersonics and Entry Systems Studies at the University of Illinois at Urbana-Champaign. The facility can support ground testing for a variety of planetary destinations by simulating entry conditions in Nitrogen, Air, and Carbon Dioxide. To best simulate the Venus atmosphere and match flight-like recession, the planned AERACEPT test campaign will use Carbon Dioxide as its test gas. AERACEPT has designed two test articles for this campaign: 1) a standard test article whose curved surface approximates a constant applied heat flux (“Closed Iso-Q” model) and 2) a novel inlet test article with a through-hole at the stagnation point (“Open Iso-Q” model). Both article types consist of a 3D-CC sample bonded to a graphite fixture. All articles will be laser scanned before and after testing to estimate shape change and recession, and the “Closed Iso-Q” articles will be instrumented with thermocouples to provide temperature histories. The test article temperatures and inlet shape change will be compared against simulations run with the Porous material Analysis Toolbox based on OpenFOAM (PATO) to validate the AERACEPT 3D-CC material response model. Due to the high thermal conductivity of 3D-CC, multidimensional effects have a large influence on the test article temperature and the standard 1-D material response tools are not sufficient for test planning. The test campaign features (e.g. article design, run duration, heat fluxes) are therefore informed by a series of 3-D simulations using state-of-the-art material response tools such as PATO. The test campaign is scheduled for spring of 2024. Expected results include 1) Key drivers of selected test conditions (e.g. matching mission flight atmosphere & recession), 2) Simulation results that informed test article design, 3) Acquired test data such as recession measurements, temperature histories, and photos, and 4) Comparisons between test results and simulation predictions.

AERACEPT↗

NASA NTRSDate not supplied

High-Enthalpy Testing to Validate Simulation of an Aerosol Capture Probe

AERACEPT (Aerosol Rapid Analysis Combined Entry Probe/sonde Technology) is a developing technology enabling in-situ aerosol particle sampling and analysis in a small spacecraft mission envelope. It integrates a passive aerosol sample collection system into a probe’s thermal protection system (TPS) to remove the need for heat shield separation and active descent control (parachutes, gliders, etc.). AERACEPT is being validated against the requirements of the Nephele mission concept, which targets the middle and lower Venus cloud layers. The proposed technology employs 3D Carbon-Carbon (3D-CC) at the probe’s nose to withstand the extreme environments encountered in a Venus entry without producing pyrolysis gases that would contaminate the mission sample collection. Any shape change of this 3D-CC sample inlet will affect airflow through the sampling system, thereby impacting aerosol sample collection bias and efficiency. Accurate prediction of the nose’s material response during entry is there-fore of fundamental importance to the development and practical use of this technology. As a result, the AERACEPT project is planning a test campaign in the newly built PlasmatronX facility with a novel “Open Iso-Q” test article to validate state-of-the-art material response tools for a simulated Venus entry. The PlasmatronX is a 350 kW inductively-coupled plasma facility developed and run by the Center for Hypersonics and Entry Systems Studies at the University of Illinois at Urbana-Champaign. The facility can support ground testing for a variety of planetary destinations by simulating entry conditions in Nitrogen, Air, and Carbon Dioxide. To best simulate the Venus atmosphere and match flight-like recession, the planned AERACEPT test campaign will use Carbon Dioxide as its test gas. AERACEPT has designed two test articles for this campaign: 1) a standard test article whose curved surface approximates a constant applied heat flux (“Closed Iso-Q” model) and 2) a novel inlet test article with a through-hole at the stagnation point (“Open Iso-Q” model). Both article types consist of a 3D-CC sample bonded to a graphite fixture. All articles will be laser scanned before and after testing to estimate shape change and recession, and the “Closed Iso-Q” articles will be instrumented with thermocouples to provide temperature histories. The test article temperatures and inlet shape change will be compared against simulations run with the Porous material Analysis Toolbox based on OpenFOAM (PATO) to validate the AERACEPT 3D-CC material response model. Due to the high thermal conductivity of 3D-CC, multidimensional effects have a large influence on the test article temperature and the standard 1-D material response tools are not sufficient for test planning. The test campaign features (e.g. article design, run duration, heat fluxes) are therefore informed by a series of 3-D simulations using state-of-the-art material response tools such as PATO. The test campaign is scheduled for spring of 2024. Expected results include 1) Key drivers of selected test conditions (e.g. matching mission flight atmosphere & recession), 2) Simulation results that informed test article design, 3) Acquired test data such as recession measurements, temperature histories, and photos, and 4) Comparisons between test results and simulation predictions.

AERACEPT↗

NASA NTRS2008

Rescue Shuttle Flight Re-Entry: Controlling Astronaut Thermal Exposure

A rescue mission for the STS-125 Hubble Telescope Repair Mission requires reentry from space with 11 crew members aboard, exceeding past cabin thermal load experience and risking crew thermal stress potentially causing cognitive performance and physiological decrements. The space shuttle crew cabin air revitalization system (ARS) was designed to support a nominal crew complement of 4 to 7 crew and 10 persons in emergencies, all in a shirt-sleeve environment. Subsequent to the addition of full pressure suits with individual cooling units, the ARS cannot maintain a stable temperature in the crew cabin during reentry thermal loads. Bulk cabin thermal models, used for rescue mission planning and analysis of crew cabin air, were unable to accurately represent crew workstation values of air flow, carbon dioxide, and heat content for the middeck. Crew temperature models suggested significantly elevated core temperatures. Planning for an STS-400 potential rescue of seven stranded crew utilized computational fluid dynamics (CFD) models to demonstrate inhomogeneous cabin thermal properties and improve analysis compared to bulk models. In the absence of monitoring of crew temperature, heart rate, metabolic rate and incomplete engineering data on the performance of the integrated cooling garment/cooling unit (ICG/CU) at cabin temperatures above 75 degrees F, related systems & models were reevaluated and tests conducted with humans in the loop. Changes to the cabin ventilation, ICU placement, crew reentry suit-donning procedures, Orbiter Program wave-off policy and post-landing power down and crew extraction were adopted. A second CFD and core temperature model incorporated the proposed changes and confirmed satisfactory cabin temperature, improved air distribution, and estimated core temperatures within safe limits. CONCLUSIONS: These changes in equipment, in-flight and post-landing procedures, and policy were implemented for the STS-400 rescue shuttle & will be implemented in any future rescue flights from the International Space Station of stranded shuttle crews.

Gillis, David B.↗

NASA NTRS1993

Tree Classification Software

This paper introduces the IND Tree Package to prospective users. IND does supervised learning using classification trees. This learning task is a basic tool used in the development of diagnosis, monitoring and expert systems. The IND Tree Package was developed as part of a NASA project to semi-automate the development of data analysis and modelling algorithms using artificial intelligence techniques. The IND Tree Package integrates features from CART and C4 with newer Bayesian and minimum encoding methods for growing classification trees and graphs. The IND Tree Package also provides an experimental control suite on top. The newer features give improved probability estimates often required in diagnostic and screening tasks. The package comes with a manual, Unix 'man' entries, and a guide to tree methods and research. The IND Tree Package is implemented in C under Unix and was beta-tested at university and commercial research laboratories in the United States.

Buntine, Wray↗

NASA NTRS2009

Status and Mission Applicability of NASA's In-Space Propulsion Technology Project

The In-Space Propulsion Technology (ISPT) project develops propulsion technologies that will enable or enhance NASA robotic science missions. Since 2001, the ISPT project developed and delivered products to assist technology infusion and quantify mission applicability and benefits through mission analysis and tools. These in-space propulsion technologies are applicable, and potentially enabling for flagship destinations currently under evaluation, as well as having broad applicability to future Discovery and New Frontiers mission solicitations. This paper provides status of the technology development, near-term mission benefits, applicability, and availability of in-space propulsion technologies in the areas of advanced chemical thrusters, electric propulsion, aerocapture, and systems analysis tools. The current chemical propulsion investment is on the high-temperature Advanced Material Bipropellant Rocket (AMBR) engine providing higher performance for lower cost. Investments in electric propulsion technologies focused on completing NASA's Evolutionary Xenon Thruster (NEXT) ion propulsion system, a 0.6-7 kW throttle-able gridded ion system, and the High Voltage Hall Accelerator (HiVHAC) thruster, which is a mid-term product specifically designed for a low-cost electric propulsion option. Aerocapture investments developed a family of thermal protections system materials and structures; guidance, navigation, and control models of blunt-body rigid aeroshells; atmospheric models for Earth, Titan, Mars and Venus; and models for aerothermal effects. In 2009 ISPT started the development of propulsion technologies that would enable future sample return missions. The paper describes the ISPT project's future focus on propulsion for sample return missions. The future technology development areas for ISPT is: Planetary Ascent Vehicles (PAV), with a Mars Ascent Vehicle (MAV) being the initial development focus; multi-mission technologies for Earth Entry Vehicles (MMEEV) needed for sample return missions from many different destinations; propulsion for Earth Return Vehicles (ERV), transfer stages to the destination, and Electric Propulsion for sample return and low cost missions; and Systems/Mission Analysis focused on sample return propulsion. The ISPT project is funded by NASA's Science Mission Directorate (SMD).

Anderson, David J.↗

NASA NTRS2016

NASA ERA Integrated CFD for Wind Tunnel Testing of Hybrid Wing-Body Configuration

The NASA Environmentally Responsible Aviation (ERA) Project explored enabling technologies to reduce impact of aviation on the environment. One project research challenge area was the study of advanced airframe and engine integration concepts to reduce community noise and fuel burn. To address this challenge, complex wind tunnel experiments at both the NASA Langley Research Center's (LaRC) 14'x22' and the Ames Research Center's 40'x80' low-speed wind tunnel facilities were conducted on a BOEING Hybrid Wing Body (HWB) configuration. These wind tunnel tests entailed various entries to evaluate the propulsion-airframe interference effects, including aerodynamic performance and aeroacoustics. In order to assist these tests in producing high quality data with minimal hardware interference, extensive Computational Fluid Dynamic (CFD) simulations were performed for everything from sting design and placement for both the wing body and powered ejector nacelle systems to the placement of aeroacoustic arrays to minimize its impact on vehicle aerodynamics. This paper presents a high-level summary of the CFD simulations that NASA performed in support of the model integration hardware design as well as the development of some CFD simulation guidelines based on post-test aerodynamic data. In addition, the paper includes details on how multiple CFD codes (OVERFLOW, STAR-CCM+, USM3D, and FUN3D) were efficiently used to provide timely insight into the wind tunnel experimental setup and execution.

Computational Fluid Dynamics↗

NASA NTRS2016

NASA ERA Integrated CFD for Wind Tunnel Testing of Hybrid Wing-Body Configuration

NASAs Environmentally Responsible Aviation (ERA) Project explores enabling technologies to reduce aviations impact on the environment. One research challenge area for the project has been to study advanced airframe and engine integration concepts to reduce community noise and fuel burn. In order to achieve this, complex wind tunnel experiments at both the NASA Langley Research Centers (LaRC) 14x22 and the Ames Research Centers 40x80 low-speed wind tunnel facilities were conducted on a Boeing Hybrid Wing Body (HWB) configuration. These wind tunnel tests entailed various entries to evaluate the propulsion airframe interference effects including aerodynamic performance and aeroacoustics. In order to assist these tests in producing high quality data with minimal hardware interference, extensive Computational Fluid Dynamic (CFD) simulations were performed for everything from sting design and placement for both the wing body and powered ejector nacelle systems to the placement of aeroacoustic arrays to minimize its impact on the vehicles aerodynamics. This paper will provide a high level summary of the CFD simulations that NASA performed in support of the model integration hardware design as well as some simulation guideline development based on post-test aerodynamic data. In addition, the paper includes details on how multiple CFD codes (OVERFLOW, STAR-CCM+, USM3D, and FUN3D) were efficiently used to provide timely insight into the wind tunnel experimental setup and execution.

Computational Fluid Dynamics↗