Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineering, Lasers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Single-shot, double-pulse determination of the detonation energy in nanosecond-laser ablation using the blast model

We demonstrate a novel single-shot method to determine the detonation energy of laser-induced plasma and investigate its performance. This approach can be used in cases where there are significant shot-to-shot variations in ablation conditions, such as laser fluctuations, target inhomogeneity, or multiple filamentation with ultrashort pulses. The Sedov blast model is used to fit two time-delayed shadowgrams measured with a double-pulse laser. We find that the reconstruction of detonation parameters is insensitive to the choice of interpulse delay in double-pulse shadowgraphy. In contrast, the initial assumption of expansion dimensionality has a large impact on the reconstructed detonation energy. The method allows for a reduction in the uncertainties of blast wave energy measurements as a diagnostic technique employed in various laser ablation applications.

42 ENGINEERING↗
DOE OSTI2024

Femto-second Laser’s Enabling New Length Scale Fabrications for Rapid Post Irradiation Examination of Materials: Concluding LDRD Project Poster

Mechanical testing campaigns are required to qualify materials for advanced reactor conditions, yet economical and safety limitations restrict the number of standardized mechanical tests that can be performed. Reducing the size of the sample is one approach to addressing these challenges and to accelerating testing. Previous research has shown that smaller mechanical test samples produce higher yield and ultimate stress values compared to values measured from standard sample sizes: the “smaller is stronger” effect. Specimens used in accelerated material testing campaigns must reflect bulk material performance to enable engineering scale material property measurement. The objective of this research project was to determine if engineering scale mechanical behavior—the yield stress—could be measured with micro-tensile test samples smaller than traditional standard testing geometries. The relationship between yield stress and sample size was explored with two different nuclear-relevant structural materials: Zircaloy-4 and tungsten. Mechanical testing of both metals demonstrated decreasing yield stress values with increasing sample gauge size across three different sizes. Yield stress values from the largest gauge size, fabricated with a femto-second laser ablation system, approach bulk material yield stress values reported in published literature. Preliminary analysis of the tungsten samples indicates the yield stress value depends on the grain characteristics within the gauge section, in addition to the gauge size. Accompanying modeling efforts, including response surface generation and crystal plasticity approaches, further demonstrated that the size of the sample gauge section alone cannot explain the change in yield stress values.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Roadmap on spatiotemporal light fields

Spatiotemporal sculpturing of light pulse with ultimately sophisticated structures represents a major goal of the everlasting pursue of ultra-fast information transmission and processing as well as ultra-intense energy concentration and extraction. It also holds the key to unlock new extraordinary fundamental physical effects. Traditionally, spatiotemporal light pulses are always treated as spatiotemporally separable wave packet as solution of the Maxwell’s equations. In the past decade, however, more generalized forms of spatiotemporally nonseparable solution started to emerge with growing importance for their striking physical effects. This roadmap intends to highlight the recent advances in the creation and control of increasingly complex spatiotemporally sculptured pulses, from spatiotemporally separable to complex nonseparable states, with diverse geometric and topological structures, presenting a bird’s eye viewpoint on the zoology of spatiotemporal light fields and the outlook of future trends and open challenges.

42 ENGINEERING↗
DOE OSTI2021

Light by design: emerging frontiers in ultrafast photon sciences and light–matter interactions

Photon sciences and technologies establish the building blocks for myriad scientific and engineering frontiers in life and energy sciences. Because of their overarching functionality, the developmental roadmap and opportunities underpinned by photonics are often semiotically mediated by the delineation of subject areas of application. In this perspective article, we map current and emerging linkages between three intersecting areas of research stewarded by advanced photonics technologies, namely light by design, outlined as (a) quantum and structured photonics, (b) light–matter interactions in accelerators and accelerator-based light sources, and (c) ultrafast sciences and quantum molecular dynamics. In each section, we will concentrate on state-of-the-art achievements and present prospective applications in life sciences, biochemistry, quantum optics and information sciences, and environmental and chemical engineering, all founded on a broad range of photon sources and methodologies. We hope that this interconnected mapping of challenges and opportunities seeds new concepts, theory, and experiments in the advancement of ultrafast photon sciences and light–matter interactions. Additionally, through this mapping, we hope to inspire a critically interdisciplinary approach to the science and applications of light by design.

42 ENGINEERING↗
DOE OSTI2022

High-Precision Mapping of Diamond Crystal Strain Using Quantum Interferometry

Crystal-strain variation imposes significant limitations on many quantum sensing and information applications for solid-state defect qubits in diamond. Thus, the precision measurement and control of diamond crystal strain is a key challenge. Here, we report diamond strain measurements with a unique set of capabilities, including micron-scale spatial resolution, a millimeter-scale field of view, and a 2-order-of-magnitude improvement in volume-normalized sensitivity over previous work, reaching 5(2)×10 -8 /√Hzμm -3 (with spin-strain coupling coefficients representing the dominant systematic uncertainty). We use strain-sensitive spin-state interferometry on ensembles of nitrogen-vacancy (N-V) color centers in single-crystal bulk diamond with low strain gradients. This quantum interferometry technique provides insensitivity to magnetic-field inhomogeneity from the electronic and nuclear spin bath, thereby enabling long N-V–ensemble electronic spin dephasing times and enhanced strain sensitivity, as well as broadening the potential applications of the technique beyond isotopically enriched or high-purity diamond. We demonstrate the strain-sensitive measurement protocol first on a confocal scanning laser microscope, providing quantitative measurement of sensitivity as well as three-dimensional strain mapping; and second on a wide-field-imaging quantum diamond microscope. Our strain-microscopy technique enables fast, sensitive characterization for diamond material engineering and nanofabrication; as well as diamond-based sensing of strains applied externally, as in diamond anvil cells or embedded diamond stress sensors, or internally, as by crystal damage due to particle-induced nuclear recoils.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Role of Equilibrium Fluctuations in Light-Induced Order

Engineering novel states of matter with light is at the forefront of materials research. An intensely studied direction is to realize broken-symmetry phases that are “hidden” under equilibrium conditions but can be unleashed by an ultrashort laser pulse. Despite a plethora of experimental discoveries, the nature of these orders and how they transiently appear remain unclear. To this end, we investigate a nonequilibrium charge density wave (CDW) in rare-earth tritellurides, which is suppressed in equilibrium but emerges after photoexcitation. Using a pump-pump-probe protocol implemented in ultrafast electron diffraction, we demonstrate that the light-induced CDW consists solely of order parameter fluctuations, which bear striking similarities to critical fluctuations in equilibrium despite differences in the length scale. By calculating the dynamics of CDW fluctuations in a nonperturbative model, we further show that the strength of the light-induced order is governed by the amplitude of equilibrium fluctuations. Overall, these findings highlight photoinduced fluctuations as an important ingredient for the emergence of transient orders out of equilibrium. Our results further suggest that materials with strong fluctuations in equilibrium are promising platforms to host hidden orders after laser excitation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Model Development for Multi-Component Fuel Vaporization and Flash Boiling

The objectives of this project are to improve the multi-component fuel droplet and film vaporization models used in internal combustion engine simulation, and to develop a comprehensive model to predict the characteristics of multi-component flash boiling spray. This work explores two approaches to fuel composition treatment for modeling multi-component fuel vaporization: one based on discretization and surrogates, and the other based on continuous thermodynamic distribution of fuel properties. The experimental data collected for model validation are done under three fuel form factors: droplet, spray, and thin film. The study on sprays also include experimentation under non-flash and flash boiling conditions, a phenomenon that enhances fuel vaporization. The main goals of this work are: Design and develop a multi-component fuel droplet and wall film vaporization model using both discrete and continuous thermodynamics methods. Design and develop an analytical model for multi-component flash boiling. Integrate the multi-component droplet and film model into multi-dimensional engine calculations to predict the fuel vaporization process under engine operation condition. Conduct multi-component droplet and fuel film vaporization experiments in a non-combusting chamber to verify the proposed vaporization models. Characterize flash boiling phenomena of multi-component fuel sprays by optical and laser diagnostic techniques. This report will detail the experimental setup and the numerical basis for developing a model to achieve the main goals listed above. Key features of observed multi-component fuel vaporization will be summarized at the end of each experimental sections, and corresponding model performance evaluation will be presented at the end of each model development section.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Strain-Induced Lateral Heterostructures in Patterned Semiconductor Nanomembranes for Micro- and Optoelectronics

The ability to tailor the energy band lineup of semiconductor materials plays a key role in the development of many electronic and optoelectronic devices and normally relies on heteroepitaxy. In this work, we report a different method, based on strain engineering, for the controlled introduction of variations in bandgap energy with lateral position in thin films. External stress is applied on Ge nanomembranes stacked with an array of amorphous-Si pillars in order to create a non-uniform strain (and therefore bandgap energy) distribution commensurate with the sample thickness variations. The resulting strain profiles are mapped using Bragg diffraction with a hard X-ray probe featuring nanoscale spatial resolution. Compared with traditional heterostructures grown by epitaxial techniques, these strain-engineered samples involve a single chemical composition and are not limited in the choice of compatible materials by any restriction imposed by lattice-matching requirements. Furthermore, their energy band lineups can be patterned in nearly arbitrary shapes using nanolithography to control the thickness profile and can be tuned actively by varying the applied stress. As a result, these structures are attractive for a wide range of device applications (including lasers, LEDs, solar cells, and thermoelectrics) that require complex heterostructure lineups with multiple bandgap energies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Perseverance’s Scanning Habitable Environments with Raman and Luminescence for Organics and Chemicals (SHERLOC) Investigation

The Scanning Habitable Environments with Raman and Luminescence for Organics and Chemicals (SHERLOC) is a robotic arm-mounted instrument on NASA’s Perseverance rover. SHERLOC has two primary boresights. The Spectroscopy boresight generates spatially resolved chemical maps using fluorescence and Raman spectroscopy coupled to microscopic images (10.1 μm/pixel). The second boresight is a Wide Angle Topographic Sensor for Operations and eNgineering (WATSON); a copy of the Mars Science Laboratory (MSL) Mars Hand Lens Imager (MAHLI) that obtains color images from microscopic scales (~13 μm/pixel) to infinity. SHERLOC Spectroscopy focuses a 40 μs pulsed deep UV neon-copper laser (248.6 nm), to a ~100 μm spot on a target at a working distance of ~48 mm. Fluorescence emissions from organics, and Raman scattered photons from organics and minerals, are spectrally resolved with a single diffractive grating spectrograph with a spectral range of 250 to ~370 nm. Because the fluorescence and Raman regions are naturally separated with deep UV excitation (<250 nm), the Raman region ~ 800 – 4000 cm -1 (250 to 273 nm) and the fluorescence region (274 to ~370 nm) are acquired simultaneously without time gating or additional mechanisms. SHERLOC science begins by using an Autofocus Context Imager (ACI) to obtain target focus and acquire 10.1 μm/pixel greyscale images. Chemical maps of organic and mineral signatures are acquired by the orchestration of an internal scanning mirror that moves the focused laser spot across discrete points on the target surface where spectra are captured on the spectrometer detector. ACI images and chemical maps (< 100 μm/mapping pixel) will enable the first Mars in situ view of the spatial distribution and interaction between organics, minerals, and chemicals important to the assessment of potential biogenicity (containing CHNOPS). Single robotic arm placement chemical maps can cover areas up to 7x7 mm in area and, with the < 10 min acquisition time per map, larger mosaics are possible with arm movements. This microscopic view of the organic geochemistry of a target at the Perseverance field site, when combined with the other instruments, such as Mastcam-Z, PIXL, and SuperCam, will enable unprecedented analysis of geological materials for both scientific research and determination of which samples to collect and cache for Mars sample return.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Investigating the Potential and Limitations of Fast Scanning Calorimetry to Simulate the Laser Power Bed Fusion Coalescence Process

Laser-Based Powder Bed Fusion (PBF-LB) • PBF-LB is part of one of seven additive manufacturing techniques • Layer wise printing that selectively coalesces discrete powder particles into a solid object o Advantages: Low anisotropy, use of engineering grade materials o Weaknesses: lack of method standardization, challenges in controlled post print quality

Blackman, Malik A. [Georgia Inst. of Technology, A↗
DOE OSTI2026

Enabling On-Demand Aerospace Component Manufacturing: Topology Optimization of GE Engine Bracket and Fabrication Using Metal FFF

Additive Manufacturing (AM) offers advantages over conventional manufacturing processes, particularly by reducing the number of parts produced through multistage combined technologies, but these often result in low manufacturing yields or require post-processing. AM facilitates the production of complex geometries with fine features, overhangs, and lattice structures. For instance, Laser Powder Bed Fusion (LPBF) technology enables the fabrication of intricate parts that can be easily post-processed by removing residual powder. Laser powder bed AM technologies are widely discussed in the literature due to their design freedom in creating complex geometries, with and without the need for support generation. However, rapid solidification due to a thermal gradient in the build direction, which leads to the formation of columnar grains and warpage, is one of the challenges. To address this challenge, we propose layer-by-layer metal FFF technology, followed by the debinding and sintering process, as an alternative to powder- and laser-based approaches. Furthermore, design for additive manufacturing (DfAM) principles are discussed to minimize the need for support generation and enable easy post-processing, thereby improving surface finish to meet high tolerances in fabricating components for aerospace and healthcare applications.

Singh, Abhishek [University of Michigan, Ann Arbor↗
DOE OSTI2020

Emergent behavior of LaNiO 3 in short-periodic nickelate superlattices

Heterostructure engineering provides an efficient way to obtain several emergent phases of LaNiO 3 , as demonstrated in recent works. In this work, a new class of short periodic superlattices, consisting of LaNiO 3 and EuNiO 3 have been grown by pulsed laser interval deposition to investigate the effect of structural symmetry mismatch on the electronic and magnetic behaviors. Using synchrotron based soft and hard x-ray resonant scattering experiments, we have found that these heterostructures undergo simultaneous electronic and magnetic transitions. Most importantly, LaNiO 3 within these artificial structures exhibits a new antiferromagnetic, charge ordered insulating phase, which may be a potential candidate to achieve high temperature superconductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Utilization of Additive Manufacturing for the Rapid Prototyping of C-Band Radiofrequency Loads

Additive manufacturing is a versatile technique that shows promise in providing quick and dynamic manufacturing for complex engineering problems. Research has been ongoing into the use of additive manufacturing for potential applications in radiofrequency (RF) component technologies. Here, we present a method for developing an effective prototype load produced from 316L stainless steel on a direct metal laser sintering machine. The model was tested using simulation software to verify the validity of the design. The load structure was manufactured by an online digital manufacturing company, showing the viability of using easily accessible tools to manufacture RF structures. The produced load was able to produce an S11 value of −22.8 dB at a C-band frequency of 5.712 GHz while under a vacuum. In a high-power test, the load was able to terminate a peak power of 8.1 MW. The discussion includes future applications of the present method and how it will help to improve the implementation of future accelerator concepts.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Abstract for CRADA between NETL and MetroLaser, Inc. (AGMT-1202)

NETL and MetroLaser, Inc. (MetroLaser) will collaborate on the commercialization design and validation of a split laser system, useful for sensing and measurement applications relevant to fossil energy and carbon management in subsurface environments relevant to carbon sequestration.

42 ENGINEERING↗
DOE OSTI2023

Abstract for CRADA between NETL and MetroLaser, Inc. (AGMT-1363)

NETL and MetroLaser, Inc. (MetroLaser) will collaborate on the commercialization design and validation of a split laser system, useful for sensing and measurement applications relevant to fossil energy and carbon management in subsurface environments relevant to carbon sequestration.

42 ENGINEERING↗