Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Wind-Tunnel Investigation of Rectangular Air-Duct Entrances in the Leading Edge of an NACA 23018 Wing, Special Report

A preliminary investigation of a number of duct entrances of rectangular shape installed in the leading edge of a wing was conducted in the NACA 20-foot tunnel to determine the external drag, the available pressure, the critical Mach numbers, and the effect on the maximum lift. The results showed that the most satisfactory entrances, which had practically no effect on the wing characteristics, had their lips approximately in the vertical plane of the leading edge of the wing. This requirement necessitated extending the lips outside the wing contour for all except the small entrances. Full dynamic pressure was found to be available over a fairly wide range of angle of attack. The critical Mach number for a small entrance was calculated to be as high as that for the plain wing but was slightly lower for the larger entrances tested.

Biermann, David↗

Static Wind Tunnel Testing of a Legged Venus Lander

A static wind tunnel test was conducted to determine the static aerodynamic coe cients of the surface lander design proposed by the Venus In-Situ Atmospheric and Geochemical Explorer (VISAGE). The baseline design of the lander consists of a spherical pressure vessel with a top-mounted circular drag plate for aerodynamic deceleration, and three xed landing legs. A modular subscale lander model, which allowed testing of several drag plate and landing leg con gurations, was fabricated using rapid-prototyping techniques. The model was tested with four di erent drag plates and three di erent leg con gurations, at a dynamic pressure of 1610 Pa and Mach number of 0.15. Testing was conducted using legs of varying diameter in order to determine the appropriate scaling of the results to Reynolds numbers representative of terminal descent at Venus. The static aerodynamic force (axial, normal, and side), and moment (rolling, pitching, yawing) coe cients for each lander con guration were determined as a function of model orientation. All model con gurations were found to be statically stable in the range of total angles of attack considered (0 to 30 deg). However, the drag performance and degree of static stability of the model were dependent on the dihedral angle of the circular drag plate. The results will enable the creation of a preliminary aerodatabase for the VISAGE lander concept, and allow the e ect of design changes on aerodynamic performance to be evaluated.

Rabinovitch, Jason↗

Results of a landing gear loads test using a 0.0405-scale model (16-0) of the space shuttle orbiter in the Rockwell International NAAL wind tunnel (OA163), volume 1

Experimental aerodynamic investigations were conducted on a sting mounted scale representation of the 140C outer mold line space shuttle orbiter configuration in the low speed wind tunnel. The primary test objectives were to define the orbiter landing gear system pressure loading and to record landing gear door and strut hingemoment levels. Secondary objectives included recording the aerodynamic influence of various landing gear configurations on orbiter force data as well as investigating 40 x 80 ft. Ames Wind Tunnel strut simulation effects on both orbiter landing gear loads and aerodynamic characteristics. Testing was conducted at a Mach number of 0.17, free stream dynamic pressure of 42.5 PSF, and Reynolds number per unit length of 1.2 million per foot. Angle of attack variation was 0 to 20 while yaw angles ranged from -10 to 10 deg.

Mennell, R. C.↗

Pressure distributions on a 1- by 3-meter semispan wing with a nonstreamwise tip in subsonic flow

Pressure distributions on a 1- by 3-meter semispan wing with a tip that is streamwise at 0 deg sweep are presented. The tip becomes nonstreamwise as the wing is swept. At 0 deg sweep angle, the semispan wing has a taper ratio of 1.0 and NACA 0012 airfoil section contours. The test was conducted in the Langley V/STOL tunnel at a freestream dynamic pressure of 2.46 kPa. Pressure distributions are presented for sweep angles of 10, 20, 30, and 40 with an angle of attack range from -6 deg to 20 deg. The data are presented without analysis or discussion.

Yip, L. P.↗

Inflatable Re-Entry Vehicle Experiment (IRVE) Design Overview

Inflatable aeroshells offer several advantages over traditional rigid aeroshells for atmospheric entry. Inflatables offer increased payload volume fraction of the launch vehicle shroud and the possibility to deliver more payload mass to the surface for equivalent trajectory constraints. An inflatable s diameter is not constrained by the launch vehicle shroud. The resultant larger drag area can provide deceleration equivalent to a rigid system at higher atmospheric altitudes, thus offering access to higher landing sites. When stowed for launch and cruise, inflatable aeroshells allow access to the payload after the vehicle is integrated for launch and offer direct access to vehicle structure for structural attachment with the launch vehicle. They also offer an opportunity to eliminate system duplication between the cruise stage and entry vehicle. There are however several potential technical challenges for inflatable aeroshells. First and foremost is the fact that they are flexible structures. That flexibility could lead to unpredictable drag performance or an aerostructural dynamic instability. In addition, durability of large inflatable structures may limit their application. They are susceptible to puncture, a potentially catastrophic insult, from many possible sources. Finally, aerothermal heating during planetary entry poses a significant challenge to a thin membrane. NASA Langley Research Center and NASA's Wallops Flight Facility are jointly developing inflatable aeroshell technology for use on future NASA missions. The technology will be demonstrated in the Inflatable Re-entry Vehicle Experiment (IRVE). This paper will detail the development of the initial IRVE inflatable system to be launched on a Terrier/Orion sounding rocket in the fourth quarter of CY2005. The experiment will demonstrate achievable packaging efficiency of the inflatable aeroshell for launch, inflation, leak performance of the inflatable system throughout the flight regime, structural integrity when exposed to a relevant dynamic pressure and aerodynamic stability of the inflatable system. Structural integrity and structural response of the inflatable will be verified with photogrammetric measurements of the back side of the aeroshell in flight. Aerodynamic stability as well as drag performance will be verified with on board inertial measurements and radar tracking from multiple ground radar stations. The experiment will yield valuable information about zero-g vacuum deployment dynamics of the flexible inflatable structure with both inertial and photographic measurements. In addition to demonstrating inflatable technology, IRVE will validate structural, aerothermal, and trajectory modeling techniques for the inflatable. Structural response determined from photogrammetrics will validate structural models, skin temperature measurements and additional in-depth temperature measurements will validate material thermal performance models, and on board inertial measurements along with radar tracking from multiple ground radar stations will validate trajectory simulation models.

Hughes, Stephen J.↗

Balanced Flow Meters without Moving Parts

Balanced flow meters are recent additions to an established class of simple, rugged flow meters that contain no moving parts in contact with flow and are based on measurement of pressure drops across objects placed in flow paths. These flow meters are highly accurate, minimally intrusive, easily manufacturable, and reliable. A balanced flow meter can be easily mounted in a flow path by bolting it between conventional pipe flanges. A balanced flow meter can be used to measure the flow of any of a variety of liquids or gases, provided that it has been properly calibrated. Relative to the standard orifice-plate flow meter, the balanced flow meter introduces less turbulence and two times less permanent pressure loss and is therefore capable of offering 10 times greater accuracy and repeatability with less dissipation of energy. A secondary benefit of the reduction of turbulence is the reduction of vibration and up to 15 times less acoustic noise generation. Both the balanced flow meter and the standard orifice-plate flow meter are basically disks that contain holes and are instrumented with pressure transducers on their upstream and downstream faces. The most obvious difference between them is that the standard orifice plate contains a single, central hole while the balanced flow meter contains multiple holes. The term 'balanced' signifies that in designing the meter, the sizes and locations of the holes are determined in an optimization procedure that involves balancing of numerous factors, including volumetric flow, mass flow, dynamic pressure, kinetic energy, all in an effort to minimize such undesired effects as turbulence, pressure loss, dissipation of kinetic energy, and non-repeatability and nonlinearity of response over the anticipated range of flow conditions. Due to proper balancing of these factors, recent testing demonstrated that the balanced flow-meter performance was similar to a Venturi tube in both accuracy and pressure recovery, but featured reduced cost and pipe-length requirements.

Kelley, Anthony R.↗

Galactic cosmic-ray mediation of a spherical solar wind flow. 1: The steady state cold gas hydrodynamical approximation

Realistic models of the outer heliosphere should consider that the interstellar cosmic-ray pressure becomes comparable to pressures in the solar wind at distances more than 100 AU from the Sun. The cosmic-ray pressure dynamically affects solar wind flow through deceleration. This effect, which occurs over a scale length of the order of the effective diffusion length at large radial distances, has important implications for cosmic-ray modulation and acceleration. As a first step toward solution of this nonlinear problem, a steady state numerical model was developed for a relatively cold spherical solar wind flow which encounters the confining isotropic pressure of the surrounding Galactic medium. This pressure is assumed to be dominated by energetic particles (Galactic cosmic rays). The system of equations, which are solved self-consistently, includes the relevant hydrodynamical equations for the solar wind flow and the spherical cosmic-ray transport equation. To avoid the closure parameter problem of the two-fluid model, the latter equation is solved for the energy-dependent cosmic-ray distribution function.

Le Roux, J. A.↗

Experimental Investigation of the NASA Common Research Model

An experimental aerodynamic investigation of the NASA Common Research Model has been conducted in the NASA NTF (National Transonic Facility). Data have been obtained at chord Reynolds numbers of 5, 19.8 and 30 million for the WB and WBT0 configurations. Data have also been obtained at a chord Reynolds number of 5 million for the WBNP, WBT+2 and WBT-2 configurations. Force and moment, surface pressure and surface flow visualization data were obtained but only the force and moment data are presented herein. Model deformation measurements, aeroelastic, nacelle/pylon Reynolds number and tail effects have been assessed. The model deformation measurements showed more twist as you go out the wing span, with a break in the high q(sub infinity) data close to CL = 0.6 which is consistent with separation near the tip. Increases in dynamic pressure give an increase in pitching moment and drag and a decrease in lift for the WB and WBT0 configuration at Mach = 0.7, 0.85 and 0.87. The addition of a nacelle/pylon gave an increase in drag, decrease in lift and a less nose down pitching moment around the design lift condition of 0.5. Increases in chord Reynolds number have been found to follow the normal Reynolds number trends except at the 19.8 million low q(sub infinity) cases. The abnormality of the 19.8 million low q(sub infinity) cases is being investigated. The tail effects also follow the expected trends. All of the data shown fall within the 2-sigma limits for repeatability.

Rivers, Melissa B.↗

Boundary-layer effect in panel flutter

The present note shows that if the supersonic Mach number is not too large, an analytical expression can be obtained for the generalized aerodynamic force relating the pressure fluctuation at the surface of a flexible plate to the plate displacement in the presence of an adjacent boundary layer. The low supersonic Mach numbers are the ones of maximum interest since it is in this Mach number region that the boundary layer has the most influence. In this respect, Dowell (1971) has already shown that the presence of a boundary layer causes about a 300% increase in flutter dynamic pressure at a Mach number of about 1.2, while it causes only about a 20% increase at a Mach number of 2.

Goldstein, M. E.↗

The magnetic barrier at Venus

Altitude profiles of the Venus magnetic barrier are derived here from a statistical analysis of the Pioneer Venus Orbiter magnetometer data. The outer boundary of the magnetic barrier is then compared with the obstacle expected from gasdynamic models of the bow shock, and the stagnation pressure is compared with that expected from gasdynamic theory. The magnetic barrier is strongest at the subsolar point and weakens as expected with increasing solar zenith angle. The existence of a north-south asymmetry in the barrier strength is also demonstrated. The magnetic barrier is about 200 km thick at the subsolar point and 800 km thick at the terminator. The magnetic barrier transfers most of the solar wind dynamic pressure to the ionosphere via the enhanced magnetic pressure. The convected field gasdynamic model predicts the correct bow shock location if the magnetic barrier is treated as the obstacle.

Zhang, T. L.↗

Evaluation of dual-tip micromanometers during 21-day implantation in goats

Investigative research efforts using a cardiovascular model required the determination of central circulatory haemodynamic and arterial system parameters for the evaluation of cardiovascular performance. These calculations required continuous beat-to-beat measurement of pressure within the four chambers of the heart and great vessels. Sensitivity and offset drift, longevity, and sources of error for eight 3F dual-tipped micromanometers were determined during 21 days of implantation in goats. Subjects were instrumented with pairs of chronically implanted fluid-filled access catheters in the left and right ventricles, through which dual-tipped (test) micromanometers were chronically inserted and single-tip (standard) micromanometers were acutely inserted. Acutely inserted sensors were calibrated daily and measured pressures were compared in vivo to the chronically inserted sensors. Comparison of the pre- and post-gain calibration of the chronically inserted sensors showed a mean sensitivity drift of 1.0 +/- 0.4% (99% confidence, n = 9 sensors) and mean offset drift of 5.0 +/- 1.5 mmHg (99% confidence, n = 9 sensors). Potential sources of error for these drifts were identified, and included measurement system inaccuracies, temperature drift, hydrostatic column gradients, and dynamic pressure changes. Based upon these findings, we determined that these micromanometers may be chronically inserted in high-pressure chambers for up to 17 days with an acceptable error, but should be limited to acute (hours) insertions in low-pressure applications.

Non-NASA Center↗

Experimental Investigation of Aeroelastic Deformation of Slender Wings at Supersonic Speeds Using a Video Model Deformation Measurement Technique

A video-based photogrammetric model deformation system was established as a dedicated optical measurement technique at supersonic speeds in the NASA Langley Research Center Unitary Plan Wind Tunnel. This system was used to measure the wing twist due to aerodynamic loads of two supersonic commercial transport airplane models with identical outer mold lines but different aeroelastic properties. One model featured wings with deflectable leading- and trailing-edge flaps and internal channels to accommodate static pressure tube instrumentation. The wings of the second model were of single-piece construction without flaps or internal channels. The testing was performed at Mach numbers from 1.6 to 2.7, unit Reynolds numbers of 1.0 million to 5.0 million, and angles of attack from -4 degrees to +10 degrees. The video model deformation system quantified the wing aeroelastic response to changes in the Mach number, Reynolds number concurrent with dynamic pressure, and angle of attack and effectively captured the differences in the wing twist characteristics between the two test articles.

Erickson, Gary E.↗

A Plasma Aerocapture and Entry System for Manned Missions and Planetary Deep Space Orbiters

A rapid mission to Mars requires a large change in vehicle velocity upon arrival to establish a stable orbit. This demand is even greater for a Neptune science, requiring many kilometers per second of V. It is clear from past mission studies that a manned Mars mission and deep space planetary orbiters require aerobraking and aerocapture which use aerodynamic drag forces to slow the spacecraft. Aerocapture would enable long term studies of the outer planets and moons that would not be possible with existing braking methodologies. While the ability to utilize these atmospheres to slow down and capture spacecraft would dramatically reduce the cost, launch mass, and travel time, currently planned approaches require significant additional spacecraft mass and risk as the spacecraft must descend deep into the planetary atmosphere in order to produce significant drag on a relatively small aeroshell. The plasma based Magnetoshell being developed in this program holds the potential to perform the desired braking with significantly increased drag and control while dramatically reducing mass. Most importantly, this technology significantly lowers the risk involved with aerocapture thereby making manned planetary missions possible. The fundamental physics of the Magnetoshell is based on demonstrated experimental results. Successful implementation will dramatically decrease radiation exposures, mission risk, launch cost, and launch mass. Implementation of aerobraking by employing a solid deflector or aeroshell as a method for orbit insertion and circularization has been successfully demonstrated in the past, resulting in launch mass savings greater than 50%. In order to reduce the effect of frictional heating and dynamic pressure on the typically fragile aeroshell, or worse solar panels, the braking must be distributed over many orbital passes at a high altitude in the less dense regions of the atmosphere. It can thus take several months for a meter-scale, 1000 kg, aeroshell to execute the many elliptic orbital passes through the atmosphere to achieve the required V. This rather slow method of braking not only reduces frictional heating and dynamic forces, but also avoids unpredictable dynamic behavior due to turbulence, as well as unknown and seasonally variable atmospheric composition and temperature which has led to dangerous, mission-critical events. For exploration class missions such as DRA 5.0 aerocapture and Thermal Protection Systems (TPS) are proposed for breaking at Mars for cargo missions. Traditional aerocapture is considered too risky for manned missions. Even with the enormous mass savings that aerocapture allows, it still requires 80 tons of aeroshell and significantly increased launch mass and propellant. As will be shown, by using Magnetoshells for aerobraking, the DRA 5.0 mission will save 224 metric tons (MT) and greater than $2 B in launch costs. Beyond the dramatic savings for existing mission architectures, a low-mass, risk-free aerocapture system would allow much more rapid missions to Mars and deep space orbiters by allowing direct, faster trajectories. As will be shown, the plasma Magnetoshell Aerobraking, Aerocapture, and Entry System (AAES) not only reduces mass and cost while enabling significant new mission architectures, but also significantly reduces radiation exposures by decreasing trip times.

Manned Missions↗

Wing pressure distributions from subsonic tests of a high-wing transport model

A wind tunnel investigation was conducted on a generic, high-wing transport model in the Langley 14- by 22-Foot Subsonic Tunnel. This report contains pressure data that document effects of various model configurations and free-stream conditions on wing pressure distributions. The untwisted wing incorporated a full-span, leading-edge Krueger flap and a part-span, double-slotted trailing-edge flap system. The trailing-edge flap was tested at four different deflection angles (20 deg, 30 deg, 40 deg, and 60 deg). Four wing configurations were tested: cruise, flaps only, Krueger flap only, and high lift (Krueger flap and flaps deployed). Tests were conducted at free-stream dynamic pressures of 20 psf to 60 psf with corresponding chord Reynolds numbers of 1.22 x 10(exp 6) to 2.11 x 10(exp 6) and Mach numbers of 0.12 to 0.20. The angles of attack presented range from 0 deg to 20 deg and were determined by wing configuration. The angle of sideslip ranged from minus 20 deg to 20 deg. In general, pressure distributions were relatively insensitive to free-stream speed with exceptions primarily at high angles of attack or high flap deflections. Increasing trailing-edge Krueger flap significantly reduced peak suction pressures and steep gradients on the wing at high angles of attack. Installation of the empennage had no effect on wing pressure distributions. Unpowered engine nacelles reduced suction pressures on the wing and the flaps.

Applin, Zachary T.↗

Real-time pilot guidance system for improved flight-test maneuvers

The real-time pilot display uplink development at the Dryden Flight Research Facility is described, with a focus on recent F-104 studies. A nose boom gathers data on the Mach number, pressure altitude, and angle of attack. The system provides the pilot with guidance to improve maneuver accuracy and fly more complex trajectories. The uplink presents the pilot with computed differences between a reference flight path and actual flight state conditions, using a downlink to the ground where engineering computations are performed, feedback is transmitted, and corrections are applied. Details of the flight test trajectories and data from test results are provided for level turns, constant thrust turns, dynamic pressure trajectories, constant radar altitude accelerations and decelerations, and a Reynolds number trajectory. The system has proved capable of reducing pilot workload and saving fuel by decreasing the flight time necessary to obtain specific data.

Schneider, E. T.↗

Effects of damping on mode shapes, volume 2

Displacement, velocity, and acceleration admittances were calculated for a realistic NASTRAN structural model of space shuttle for three conditions: liftoff, maximum dynamic pressure and end of solid rocket booster burn. The realistic model of the orbiter, external tank, and solid rocket motors included the representation of structural joint transmissibilities by finite stiffness and damping elements. Data values for the finite damping elements were assigned to duplicate overall low-frequency modal damping values taken from tests of similar vehicles. For comparison with the calculated admittances, position and rate gains were computed for a conventional shuttle model for the liftoff condition. Dynamic characteristics and admittances for the space shuttle model are presented.

Gates, R. M.↗

Pressure Distributions from Subsonic Tests of a NACA 0012 Semispan Wing Model

An unswept, semispan wing model incorporating a NACA 0012 airfoil section was tested in the Langley 14- by 22-Foot Subsonic Tunnel. This report contains pressure data which document effects of wing configuration and free-stream conditions on wing pressure distributions. The untwisted wing incorporated a full-span, leading-edge Krueger flap and a full-span, single-slotted trailing-edge flap. The trailing-edge flap was tested at a deflection angle of 40 degrees and the Krueger flap at a deflection of 55 degrees. Three wing configurations were tested: cruise, trailing-edge flap only, and Knueger flap and trailing-edge flap deployed. Tests were conducted at free-stream dynamic pressures of 15, 30 and 60 psf, with corresponding chord Reynolds numbers of 1.22 to 2.11 million and Mach numbers of 0.12 to 0.20. Angles of attack presented range from 0 to 20 degrees, depending on wing configuration. The data are presented without analysis.

Applin, Zachary T.↗

Modeling the Influence of Moulin Shape on Subglacial Hydrology

Subglacial models represent moulins as cylinders or cones, but field observations suggest that the upper part of moulins in the Greenland Ice Sheet has more complex shapes. These more complex shapes should cause englacial water storage within moulins to vary as a function of depth, a relationship not currently accounted for in models. Here, we use a coupled englacial-subglacial channel model to explore how moulin shape affects depth-dependent moulin water storage and water pressure dynamics within a subglacial channel. We simulate seven different moulin shapes across a range of moulin sizes. We find that the englacial storage capacity at the water level is the main control over the daily water level oscillation range and that depth-varying changes in englacial water storage control the temporal shape of this oscillation. Further, the cross-sectional area of the moulin within the daily oscillation range, but not above or below this range, controls pressures within the connected subglacial channel. Specifically, large cross-sectional areas can dampen daily to weekly oscillations that occur in the surface meltwater supply. Our findings suggest that further knowledge of the shape of moulins around the equilibrium water level would improve englacial storage parameterization in subglacial hydrological models and aid predictions of hydrodynamic coupling.

Moulin↗