Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DRILLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Regolith history from cosmic-ray-produced nuclides

A model is given for regolith development by which the meteoroid impact parameters (time of last major impact, soil escape rate, and soil turnover depths) are determined from the Gd isotope data for the Apollo 15 and 16 drill stems. The time of the last major impact, cosmic-ray-produced-nuclide-clock reset time, at the Apollo 15 site is 0.6-1.3 aeon. The reset time at the Apollo 16 site is between 1.54 plus or minus 0.14 and 3.3-4.0 aeon. The average soil escape rate from the moon corresponding to the 1.54 plus or minus 0.14 aeon reset time is between 70 and 110 cm/aeon and corresponding to the 3.3 and 4.0 aeon reset time is between 36 and 56 cm/aeon. The soil turnover depth for the 1.54 plus or minus 0.14 aeon reset time is 250 cm and for the 3.3-4.0 aeon reset time is 750 cm. The Gd data restrict the change with time of the meteoroid flux during the past 1.4 aeon.

Fireman, E. L.↗
NASA NTRS1974

Mixing of the lunar regolith

A probabilistic model for mixing and turnover rates for the lunar regolith due to meteoritic impact is presented and evaluated using results from laboratory impact experiments and estimated meteoritic fluxes. The upper millimeter of the lunar surface is shown to be the primary mixing zone in the regolith and an important source for impact melts and vapors. Below this 'mixing layer' the rate of mixing and turnover decreases very rapidly with increasing depth, consistent with well-preserved stratigraphy and resident times deduced from deep drill core tube samples.

Gault, D. E.↗
NASA NTRS1974

Lunar surface dynamics - Some general conclusions and new results from Apollo 16 and 17

The exposure ages of Apollo 17 rocks as measured by tracks and rare gases are discussed and a description is given of an investigation of a unique rock. The investigation will be an aid for the establishment of the long-term energy spectrum of solar flare heavy particles. The track record of several Apollo 17 soils is examined. It is shown that the Apollo 17 deep drill stem might make it possible to extend the energy range over which the fossil record of galactic cosmic rays can be studied. A review is provided regarding the experimental data obtained for the rates of several dynamical processes on the lunar surface.

Crozaz, G.↗
NASA NTRS1975

Energy survey - What can R&D do by 1985

Research and development in the field of energy is generally recognized as requiring long lead times before the results are felt. Near term relief from foreign oil dependence will be achieved by reducing energy consumption through conservation and by increasing domestic energy supply through expanded exploration and drilling for oil and natural gas, and by increased coal production. This paper describes the results of an informal survey performed by NASA within its own agency to determine if any research and development activities might be an exception to the general rule of long lead times and thus have significant impact by 1985 on oil and natural gas consumption.

Copps, S. L.↗
NASA NTRS1975

Design and fabrication of an end effector

The construction is described of a prototype mechanical hand or 'end effector' for use on a remotely controlled robot, but with possible application as a prosthetic device. An analysis of hand motions is reported, from which it is concluded that the two most important manipulations (apart from grasps) are to be able to pick up a tool and draw it into a nested grip against the palm, and to be able to hold a pistol-grip tool such as an electric drill and pull the trigger. A model was tested and found capable of both these operations.

Crossley, F. R. E.↗
NASA NTRS1975

Arizona land use experiment

Utilization of new sources of statewide remote sensing data, taken from high-altitude aircraft and from spacecraft is discussed along with incorporation of information extracted from these sources into on-going land and resources management programs in Arizona. Statewide cartographic applications of remote sensor data taken by NASA high-altitude aircraft include the development of a statewide semi-analytic control network, the production of nearly 1900 orthophotoquads (image maps) that are coincident in scale and area with the U.S. Geological Survey (USGS) 7. 5 minute topographic quadrangle map series, and satellite image maps of Arizona produced from LANDSAt multispectral scanner imagery. These cartographic products are utilized for a wide variety of experimental and operational earth resources applications. Applications of the imagery, image maps, and derived information discussed include: soils and geologic mapping projects, water resources investigations, land use inventories, environmental impact studies, highway route locations and mapping, vegetation cover mapping, wildlife habitat studies, power plant siting studies, statewide delineation of irrigation cropland, position determination of drilling sites, pictorial geographic bases for thematic mapping, and court exhibits.

Winikka, C. C.↗
NASA NTRS1976

Locking mechanism for orthopedic braces

A locking mechanism for orthopedic braces is described which automatically prevents or permits the relative pivotable movement between a lower brace member and an upper brace member. The upper and lower brace members are provided with drilled bores within which a slidable pin is disposed, and depending upon the inclination of the brace members with respect to a vertical plane, the slidable pin will be interposed between both brace members. The secondary or auxiliary latching device includes a spring biased, manually operable lever bar arrangement which is manually unlatched and automatically latched under the influence of the spring.

I-Lechao, J.↗
NASA NTRS1976

Lineaments on Skylab photographs: Detection, mapping, and hydrologic significance in central Tennessee

The author has identified the following significant results. Lineaments were detected on Skylab photographs by stereo viewing, projection viewing, and composite viewing. Sixty-nine percent more lineaments were found by stereo viewing than by projection, but segments of projection lineaments are longer; total length of lineaments found by these two methods is nearly the same. Most Skylab lineaments consist of topographic depression: stream channel alinements, straight valley walls, elongated swales, and belts where sinkholes are abundant. Most of the remainder are vegetation alinements. Lineaments are most common in dissected areas having a thin soil cover. Results of test drilling show: (1) the median yield of test wells on Skylab lineaments is about six times the median yield of all existing wells; (2) three out of seven wells on Skylab lineaments yield more than 6.3 1/s (110 gal/min): (3) low yields are possible on lineaments as well as in other favorable locations; and (4) the largest well yields can be obtained at well locations of Skylab lineaments that also are favorably located with respect to topography and geologic structure, and are in the vicinity of wells with large yields.

Moore, G. K.↗
NASA NTRS1976

Flexural fatigue of hollow rolling elements

Hollow cylindrical bars were tested in the rolling-contact fatigue tester to determine the effects of material and outside diameter to inside diameter (OD/ID) ratios of 2.0, 1.6, 1.4, and 1.2 on fatigue failure mode and subsequent failure propagation. The range of applied loads with these OD/ID ratios resulted in maximum tangential tensile stresses ranging from 165 to 655 megapascals (24,000 to 95,000 psi) at the bore surface. Flexural failures of the hollow test bars occurred when this bore stress was 490 megapascals (71,000 psi) or greater with AISI 52100 hollow bars and 338 megapascals (49,000 psi) or greater with AISI M-50 hollow bars. Good correlation was obtained in relating the failures of these hollow bars with flexural failures of drilled balls from previously published full scale bearing tests.

Bamberger, E. N.↗
NASA NTRS1978

Cast-in-place grommets for honeycomb substrates

Teflon grommet, cast in place, is easily installed and compatible with honeycomb structural integrity. After casting, grommet blank had only minimum hole size; however, opening can be enlarged by drilling to accommodate larger range of cable diameters. Since grommet is installed flush with adjacent mounting surfaces, it cannot fall out.

Parker, M. K.↗
NASA NTRS1975

Multispectral color photography for mineral exploration by the remote sensing of biogeochemical anomalies

Selected band multispectral photography was evaluated as a mineral exploration tool by detecting stress on trees caused by underground mineralization. Ground truth consisted of two test sites in the Prescott National Forest within which the mineralization had been established by a drilling program. Species of trees were categorized as background, intermediate, and anomalous based upon where they grew with respect to this underlying mineralization. Soil geochemistry and the metal content of ashed samples of the trees were studied in relation to the inferred locus of mineralization. Computer analysis of the reflectance spectra of mineralized trees confirmed that the relative percent reflectance differences of trees growing in anomalous areas was less than that of the same tree species growing in background areas.

Yost, E.↗
NASA NTRS1976

Development of technology for the fabrication of reliable laminar flow control panels on subsonic transports

The feasibility of using porous composite materials (Kevlar, Doweave, and Leno Weave) as lightweight, efficient laminar flow control (LFC) surface materials is compared to the metallic 319L stainless Dynapore surfaces and electron beam drilled composite surfaces. Areas investigated include: (1) selection of the LFC-suitable surface materials, structural materials, and fabrication techniques for the LFC aircraft skins; (2) aerodynamic static air flow test results in terms of pressure drop through the LFC panel and the corresponding effective porosity; (3) structural design definition and analyses of the panels, and (4) contamination effects on static drop and effective porosity. Conclusions are presented and discussed.

Source record↗
NASA NTRS1976

Applications of aerospace technology to petroleum exploration. Volume 1: Efforts and results

The feasibility of applying aerospace techniques to help solve significant problems in petroleum exploration is studied. Through contacts with petroleum industry and petroleum service industry, important petroleum exploration problems were identified. For each problem, areas of aerospace technology that might aid in its solution were also identified where possible. Topics selected for investigation include: seismic reflection systems; down-hole acoustic techniques; identification of geological analogies; drilling methods; remote geological sensing; and sea floor imaging and mapping. Specific areas of aerospace technology are applied to 21 concepts formulated from the topics of concern.

Jaffe, L. D.↗
NASA NTRS1977

Borehole hydraulic coal mining system analysis

The borehole hydraulic coal mining system accesses the coal seam through a hole drilled in the overburden. The mining device is lowered through the hole into the coal seam where it fragments the coal with high pressure water jets which pump it to the surface as a slurry by a jet pump located in the center of the mining device. The coal slurry is then injected into a pipeline for transport to the preparation plant. The system was analyzed for performance in the thick, shallow coal seams of Wyoming, and the steeply pitching seams of western Colorado. Considered were all the aspects of the mining operation for a 20-year mine life, producing 2,640,000 tons/yr. Effects on the environment and the cost of restoration, as well as concern for health and safety, were studied. Assumptions for design of the mine, the analytical method, and results of the analysis are detailed.

Floyd, E. L.↗
NASA NTRS1977

An experimental investigation of shock wave-turbulent boundary layer interactions with and without boundary layer suction: A data summary report

Tabulated data from a series of experimental studies of the interaction of a shock wave with a turbulent boundary layer in axisymmetric flow configurations is presented. The studies were conducted at the walls of circular wind tunnels and on the cylindrical centerbody of an annular flow channel. Detailed pitot pressure profiles and wall static pressure profiles upstream of, within and downstream of the interaction region are given. Results are presented for flows at nominal freestream Mach Numbers of 2, 3 and 4. For studies at the tunnel sidewalls, the shock waves were produced by conical shock generators mounted on the centerline of the wind tunnel at zero angle of attack. The annular ring generator was used to produce the shock wave at the centerbody of the annular flow channel. The effects of boundary layer bleed were examined in the investigation. Both bleed rate and bleed location were studied. Most of the bleed studies were conducted with bleed holes drilled normal to the wall surface but the effects of slot suction were also examined. A summary of the principal results and conclusions is given.

Sun, C. C.↗
NASA NTRS1976

Lunar Science Conference, 7th, Houston, Tex., March 15-19, 1976, Proceedings. Volume 1 - Regolith studies. Volume 2 - Petrogenetic studies of mare and highland rocks. Volume 3 - The moon and other bodies

Attention is given to lunar core studies (multi-core, deep drill, and drive tube), surface soil studies (petrography and geochemistry, light and volatile element studies, and agglutinate related studies), and surfaces process studies. Also considered are mare basalts, with emphasis on mineralogy and petrology, chemical and isotopic studies, and constraints and models of basalt evolution, along with breccia and highland samples with attention given to geochronology, boulders and consortium studies and the formation of highland samples. Remote sensing and photogeology of the moon, crustal bombardment, physical properties of the moon, and comparative planetology are also discussed.

Merrill, R. B.↗
NASA NTRS1976

Ferromagnetic resonance and magnetic studies of cores 60009/60010 and 60003 - Compositional and surface-exposure stratigraphy

Ferromagnetic resonance and static magnetic measurements were made on 131 samples from core 60009/60010 and on 40 samples from section 60003 of the Apollo 16 deep drill core. These studies provided depth profiles for composition, in terms of the concentration of FeO, and relative surface exposure age (or maturity), in terms of the values of the specific FMR intensity normalized to the FeO content. For core 60009/60010, the concentration of FeO ranged from about 1.6 wt.% to 5.8 wt.% with a mean value of 4.6 wt.% and the maturity ranged from immature to mature with most of the soils being submature. A systematic decrease in maturity from the lunar surface to a depth of about 12.5 cm was observed in core section 60010. For core section 60003, the concentration of FeO ranged from about 5.2 wt.% to 7.5 wt.% with a mean value of 6.4 wt.% and the maturity ranged from submature to mature with most of the soils being mature.

Morris, R. V.↗
NASA NTRS1976

Microstratigraphy of the lunar regolith and compaction ages of lunar breccias

Fossil track analyses of impregnated core sections from the Apollo 15 and 16 deep drill cores were used to study two types of distinct layers of about 1 mm and about several mm thick in the lunar regolith. The data supports a mixing model hypothesis for the origin of the sampled soil column dominated by large, fresh feldspar fragments. The boundary track method and the track gradient method were used to study the compaction ages of lunar breccias.

Goswami, J. N.↗