Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cell Fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Solid-phase hetero epitaxial growth of α-phase formamidinium perovskite

Conventional epitaxy of semiconductor films requires a compatible single crystalline substrate and precisely controlled growth conditions, which limit the price competitiveness and versatility of the process. We demonstrate substrate-tolerant nano-heteroepitaxy (NHE) of high-quality formamidinium-lead-tri-iodide (FAPbI 3 ) perovskite films. The layered perovskite templates the solid-state phase conversion of FAPbI 3 from its hexagonal non-perovskite phase to the cubic perovskite polymorph, where the growth kinetics are controlled by a synergistic effect between strain and entropy. The slow heteroepitaxial crystal growth enlarged the perovskite crystals by 10-fold with a reduced defect density and strong preferred orientation. This NHE is readily applicable to various substrates used for devices. The proof-of-concept solar cell and light-emitting diode devices based on the NHE-FAPbI 3 showed efficiencies and stabilities superior to those of devices fabricated without NHE.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electrochemical and In Situ Spectroscopic Study of the Effect of Prussian Blue as a Mediator in a Solid-State Supercapacitor

In situ X-ray absorption spectroscopy (XAS) along with electrochemical measurements were used to explore the redox activity of Prussian blue (PB) and its contribution to pseudocapacitance in an asymmetrical solid-state supercapacitor (SC). The SC, with a configuration of (activated carbon)/polymer electrolyte membrane/(activated carbon + PB), was fabricated with an embedded KCl saturated Ag/AgCl reference electrode. The potentials of the two electrodes were generally displaced proportionally with increase in the cell voltage. Upon negative polarization from the open circuit voltage (OCV) condition to -3 V, the charge capacity was greater than that upon positive polarization from the OCV condition to +3 V, in agreement with the higher fraction of Fe(III) than that of Fe(II) and the low concentration of K ions in PB. Detailed analysis of cyclic voltammetry data in the range between 0 and -3 V indicates that the battery-like contribution to the charge current was 96% that of the capacitor-like contribution at a scanning rate of 2.5 mV s -1 but only 15% at 100 mV s -1 . The in situ XAS characterization results indicate that the majority of Fe was reversibly charged and discharged between Fe(III) and Fe(II) during positive and negative polarizations with minimal changes in local atomic structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Investigation of Scanning Droplet Cell Technology for Electrochemical Deposition of Custom Three-Dimensional Alloys

The goal of this project was to assess the feasibility of a new method of electroplating, which we have termed “electroprinting”, for fabricating millimeter to centimeter metal parts with full density, and eventually, with bespoke 3D internal density patterns. Alloys, gradients and varying density is beyond the scope of this work, and efforts were focused on developing the technology to be capable of printing solid parts, beyond the lines and columns previously reported in the literature. Enabling this technology would expand the design space possible for the WPD program, allowing for smooth and complex density gradients in parts rather than discrete density steps between multilayers. We successfully designed and built an electroprinting apparatus, capable of printing copper in customizable 1-D patterns, which can be printed in stacked layers to form 3D parts. We successfully characterized the flat printed patterns, however, have encountered difficulty in characterizing multilayer prints. We have partially addressed the feasibility question, by developing the method for electroprinting 3D parts, however, some questions about the internal porosity and density of these parts still remain.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High Efficiency Evaporated CdSeTe/CdTe Solar Cells With and Without MgZnO Buffer Layer

High efficiencies of ~19% CdTe solar cell devices were made using a thermal evaporation technique to deposit absorber layers of CdSe and CdTe. The absorber films were very high quality for a device fabrication, and with demonstrated high efficiency, it is a viable option to employ thermal evaporation in research and manufacturing. We also investigated four different interfaces scenarios of with and without MZO and CdSe in the device near front interface. The results clearly indicate that Se plays a key role in improving device performance, but the MZO is not necessarily required unless experiment goals demanded. Removing the MZO layer from the device structure and being able to use thermal evaporator for CdTe deposition will help with cost reduction in manufacturing.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2025

High-Throughput Microfluidic Electroporation (HTME): A Scalable, 384-Well Platform for Multiplexed Cell Engineering

Electroporation-mediated gene delivery is a cornerstone of synthetic biology, offering several advantages over other methods: higher efficiencies, broader applicability, and simpler sample preparation. Yet, electroporation protocols are often challenging to integrate into highly multiplexed workflows, owing to limitations in their scalability and tunability. These challenges ultimately increase the time and cost per transformation. As a result, rapidly screening genetic libraries, exploring combinatorial designs, or optimizing electroporation parameters requires extensive iterations, consuming large quantities of expensive custom-made DNA and cell lines or primary cells. To address these limitations, we have developed a High-Throughput Microfluidic Electroporation (HTME) platform that includes a 384-well electroporation plate (E-Plate) and control electronics capable of rapidly electroporating all wells in under a minute with individual control of each well. Fabricated using scalable and cost-effective printed-circuit-board (PCB) technology, the E-Plate significantly reduces consumable costs and reagent consumption by operating on nano to microliter volumes. Furthermore, individually addressable wells facilitate rapid exploration of large sets of experimental conditions to optimize electroporation for different cell types and plasmid concentrations/types. Use of the standard 384-well footprint makes the platform easily integrable into automated workflows, thereby enabling end-to-end automation. We demonstrate transformation of E. coli with pUC19 to validate the HTME's core functionality, achieving at least a single colony forming unit in more than 99% of wells and confirming the platform's ability to rapidly perform hundreds of electroporations with customizable conditions. This work highlights the HTME's potential to significantly accelerate synthetic biology Design-Build-Test-Learn (DBTL) cycles by mitigating the transformation/transfection bottleneck.

Gaillard, William R↗
DOE OSTI2026

A Relief Zone Architecture for Enhanced Durability of Ultrathin Membranes in Electrochemical Conversion Devices

Premature cell failures in electrochemical conversion systems often result when membrane electrode assemblies (MEAs) are prepared with ultra-thin (= 15 micrometer-thick) polymer electrolyte membranes (PEMs). These high-performance PEMs are susceptible to mechanical degradation from stress concentrations arising from component and device-level integration. Herein, a relief zone was developed to mitigate mechanical degradation by alleviating excess and non-uniform compression across the active area. Relief zones, created through the ablation of carbonaceous diffusion material achieves a seamless adaptation across a range of MEA dimensions and electrochemical applications without need for costly hardware modifications. This concept was demonstrated using fuel cells as a case study. Accelerated stress test (AST) validations yielded a 6-fold improvement for MEAs prepared with relief zones (i.e., lifetime approximately 1500 h) compared to those fabricated using conventional edge-protection techniques, showcasing the utility of this technique in decoupling integration and device-level engineering effects from intrinsic material limitations for durable electrochemical devices.

14 SOLAR ENERGY↗
DOE OSTI2022

The N3/TiO 2 interfacial structure is dependent on the pH conditions during sensitization

The electronic structure of the N3/TiO 2 interface can directly influence the performance of a dye sensitized solar cell (DSSC). Therefore, it is crucial to understand the parameters that control the dye’s orientation on the semiconductor’s surface. A typical step in DSSC fabrication is to submerge the nanoparticulate semiconductor film in a solution containing the dye, the sensitizing solution. The pH of the N3 sensitizing solution determines the distribution of the N3 protonation states that exist in solution. Altering the pH of the sensitizing solution changes the N3 protonation states that exist in solution and, subsequently, the N3 protonation states that anchor to the TiO 2 substrate. We utilize the surface specific technique of heterodyne detected vibrational sum frequency generation spectroscopy to determine the binding geometry of N3 on a TiO 2 surface as a function of the sensitizing solution pH conditions. It is determined that significant reorientation of the dye occurs in pH ≤ 2.0 conditions due to the lack of N3-dye carboxylate anchoring groups participating in adsorption to the TiO 2 substrate. Consequently, the change in molecular geometry is met with a change in the interfacial electronic structure that can hinder electron transfer in DSSC architectures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Impact of electrode thick spot irregularities on polymer electrolyte membrane fuel cell initial performance

Polymer electrolyte membrane fuel cells have great potential for power generation in many applications, but to implement them on a larger scale, understanding of quality requirements, tolerances, and controls during manufacturing must improve. As part of this broad challenge, irregularities resulting from the membrane electrode assembly production process must be studied to determine if they impact the performance of the cell. One potential irregularity is a locally increased thickness of the coated or deposited electrode. In order to understand and provide insight into the impact of such irregularities, we intentionally created thick spots in the center of cathode electrodes. The thick spots fabricated by two different approaches were carefully characterized by optical microscopy, X-ray fluorescence spectroscopy and scanning electron microscopy (SEM). We found that the impact of the thick spots on the electrochemically active catalyst area and mass activity was minimal. However, specific electrode thick spot irregularities significantly impacted the mass transport properties of the cells. Based on SEM analysis, the likely cause of the performance drop is morphological changes associated with the creation of the thick spot irregularity. Spatial performance results obtained with a segmented cell system further indicated that the area of the performance impact exceeded that of the intentionally created thick spot.

25 ENERGY STORAGE↗
DOE OSTI2023

Toward High Efficiency Water Processed Organic Photovoltaics: Controlling the Nanoparticle Morphology with Surface Energies

Here efficient organic photovoltaic devices fabricated from water-based colloidal dispersions with donor:acceptor composite nanoparticles achieving up to 9.98% power conversion efficiency (PCE) are reported. This high efficiency for water processed organic solar cells is attributed to morphology control by surface energy matching between the donor and the acceptor materials. Indeed, due to a low interfacial energy between donor and the acceptor, no large phase separation occurs during the nanoparticle formation process as well as upon thermal annealing. Indeed, synchrotron-based scanning transmission X-ray microscopy reveals that the internal morphology of composite nanoparticles is intermixed as well as the active layer morphology after thermal treatment. The PCE of this system reaches 85% that of devices prepared from chlorinated solvent. The gap between water-based inks and organic solvent-based inks gets narrower, which is promising for the development of eco-friendly processing and fabrication of organic photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2025

Cold air quench control of local crystallization environment in fully air-processed carbon-based perovskite solar cells

Carbon-based perovskite solar cells (C-PSCs) present a low-cost route to efficient photovoltaic technology. Gas quenching is an essential process commonly used for solvent extraction in scalable module fabrication using solution processes, but film quality remains highly sensitive to the localized environmental processing temperature, especially during intermediate phase transitions before perovskite film high temperature annealing. In this study, we introduce a cold air quench strategy to precisely control the local crystallization temperature that simultaneously promotes uniform crystallization and facilitates strain relaxation in fully air-processed C-PSCs. It is found that implementing dry air at 10 °C as the quenching gas yields a champion power conversion efficiency (PCE) of 20.52 %, with preferential (110) orientation and reduced, homogenized in-plane strain. This newly developed technique of a cost-effective low temperature air quenching process also enhances carrier lifetime, reduces interface recombination, and improves charge extraction. Furthermore, this work presents cold air quenching as a scalable, economic method to control perovskite crystallization and strain in C-PSC fabrication, advancing the industrial viability of high-performance perovskite modules.

14 SOLAR ENERGY↗
DOE OSTI2025

Application of lipid-stabilized liquid-liquid interfaces in 3D printing of biomaterials

Developing strategies to stabilize liquid-liquid interfaces is essential for advancing applications in various biomedical systems. This study introduces a novel biocompatible in situ-forming material in which lipid self-assembly stabilizes water–oil interfaces, enabling controlled structuring of liquids through liquid-in-liquid 3D printing. The stabilization process, driven by the formation of nanostructures at the interface, is thoroughly analyzed through small-angle X-ray scattering (SAXS), rheometry, and microscopy techniques. This material system enables the fabrication of complex 3D constructs, including fibers, substrates, and microneedle patches, which exhibit outstanding mechanical properties and biocompatibility, as confirmed by tensile testing and cell viability tests. Here, by leveraging the unique properties of lipid-stabilized interfaces, this work demonstrates the potential of this approach for diverse biomedical applications such as drug delivery and tissue engineering while establishing a foundation for future advancements in liquid-in-liquid 3D printing technology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The mechanical behavior of metal-halide perovskites: Elasticity, plasticity, fracture, and creep

Wide ranging mechanical properties — elasticity, plasticity, fracture, and creep — most relevant to the mechanical reliability of perovskite solar cells (PSCs) are systematically investigated. High quality bulk single-crystals of the commonly studied metal-halide perovskites (MHPs) relevant to PSCs are fabricated and studied: CH 3 NH 3 PbBr 3 (MAPbBr 3 ) and CH 3 NH 3 PbI 3 (MAPbI 3 ). The first direct measurement of MHP Young's modulus (E) using uniaxial compression reveals E <100> of 13.1 ± 1.3 and 10.6 ± 1.0 GPa for MAPbBr 3 and MAPbI 3 , respectively. Further, the Vickers micro-hardness H (100) of MAPbBr 3 and MAPbI 3 is 0.54±0.02 GPa and 0.76±0.05 GPa, respectively. The Vickers micro-indentation fracture toughness K IC of MAPbBr 3 and MAPbI 3 is estimated at 0.20±0.03 MPa∙m 0.5 and 0.18±0.03 MPa∙m 0.5 , respectively. The stress-exponent, n, extracted from nanoindentation creep data is ~8 and ~10 for MAPbBr 3 and MAPbI 3 , respectively. The trends in these properties are discussed. These properties are best estimates and are recommended for use in future mechanical behavior and reliability analyses of MHPs and PSCs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultra-light antennas via charge programmed deposition additive manufacturing

Abstract The demand for lightweight antennas in 5 G/6 G communication, wearables, and aerospace applications is rapidly growing. However, standard manufacturing techniques are limited in structural complexity and easy integration of multiple material classes. Here we introduce charge programmed multi-material additive manufacturing platform, offering unparalleled flexibility in antenna design and the capability for rapid printing of intricate antenna structures that are unprecedented or necessitate a series of fabrication routes. Demonstrating its potential, we present a transmitarray antenna composed of an interconnected, multi-layered array of dielectric/conductive S-ring unit cells, reducing 94% mass of conventional antenna configurations. A fully printed circular polarized transmitarray system fed by a source and a Risley prism antenna system operating at 19 GHz both show close alignment between testing results and numerical simulations. This printing method establishes a universal platform, propelling discovery of new antenna designs and enabling data-driven design and optimizations where rapid production of antenna designs is crucial.

Science & Technology - Other Topics↗
DOE OSTI2021

Multifunctional Li-ion Conducting Interfacial Materials for Lithium Metal Batteries”

The overall approach will focus on the development and optimization of synthesis methods and precursors for multifunctional Li-ion conducting interfacial materials, protective layer composition, and protective layer fabrication methods. This will be accompanied by property measurement and characterization (conductivity, mechanical properties, etc.) for the protective layer on Li metal, along with cell testing.

25 ENERGY STORAGE↗
DOE OSTI2023

Highly durable platinum group metal-free catalyst fiber cathode MEAs for proton exchange membrane fuel cells

For this work, Fe-based platinum group metal (PGM)-free catalysts were incorporated into electrospun fiber mat or powder cathode membrane-electrode-assemblies (MEAs) with a Nafion 211 membrane and a Pt/C powder anode. Fabrication and characterization tests were performed on MEAs with: (1) a conventional powder cathode with a neat Nafion binder, (2) a fiber mat cathode with a Nafion/polyethylene oxide (PEO) binder, where PEO was extracted before MEA testing, (3) a powder cathode with a blended binder of Nafion and polyvinylidene fluoride (PVDF), and (4) a series of fiber mat cathodes with different Nafion/PVDF binder weight ratios. Cathode degradation occurred, with a loss in power output, in MEAs with a neat Nafion powder cathode or with a Nafion fiber cathode. In contrast, little or no power loss was observed for powder or fiber cathodes when the binder was a blend of Nafion and PVDF. The presence of hydrophobic PVDF drove water and electrogenerated peroxide out of the cathode, away from catalyst particles, which improved cathode durability, but PVDF also decreased the binder conductivity and slowed oxygen reduction kinetics, resulting in lower power densities. A 75:25 w:w Nafion:PVDF fiber cathode MEA was the best compromise for maximizing power and minimizing catalyst degradation. For such a cathode, with a PGM-free cathode catalyst loading of 3.0 mg cm –2 , a power density of 88 mW cm –2 at 0.5 V, 80 °C, and 200 kPa abs pressure was maintained for 80 h of continuous operation.

25 ENERGY STORAGE↗
DOE OSTI2026

Automation of Solid Oxyde Electrolyzer Cell (SOEC) & Stack Assembly

The work performed under this agreement before the No/Go decision amounted to the following: 1. Preliminary manufacturing requirements defined by business sensitivity, baseline processes & risk assessment; 2. Process & materials development, in-line gauge exploration, and preliminary automation work used to reduce risk & further refine equipment specifications; 3. “Request for Quote” issued to multiple suppliers for major equipment; 4. Application specific equipment, hardware, and fixturing will be more beneficial to fabricate inhouse; 5.Current proposals & estimates meet cycle time, capital spend, & direct labor; space is on target but requires awareness; 6. Team will continue to explore opportunities to reduce risk (dry time, traceability); 7. Go / No-Go, Purchase Orders, Equipment build & commissioning next All other future task were not completed because during the Go /No-Go decision it was confirmed this project was a "No-Go" and did not proceed past BP1; these included the following: 1. Preliminary manufacturing requirements defined by business sensitivity, baseline processes & risk assessment; 2. Process & materials development, in-line gauge exploration, and preliminary automation work used to reduce risk & further refine equipment specifications; 3. “Request for Quote” issued to multiple suppliers for major equipment; 4. Application specific equipment, hardware, and fixturing will be more beneficial to fabricate inhouse; 5. Current proposals & estimates meet cycle time, capital spend, & direct labor; space is on target but requires awareness; 6. Team will continue to explore opportunities to reduce risk (dry time, traceability) In final preparation of the termination of the Automation of Solid Oxyde Electrolyzer Cell (SOEC) & Stack Assembly, Cummins has purchased no equipment with government funds, and there is no government-owned property in Cummins possession related to this project. Minimal labor and travel were completed and paid. This acts as the Final technical report and concludes our business with DOE on this grant.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recent advances in integrating platinum group metal-free catalysts in proton exchange membrane fuel cells

Platinum group metal (PGM)-free catalysts are promising low-cost materials for the oxygen reduction reaction in proton exchange membrane fuel cells (PEMFCs). A variety of chemical precursors and synthesis methods have been proposed to increase their catalytic activity. In comparison, significantly less attention has been dedicated to the integration of these PGM-free catalysts into operating electrodes by investigating the role of the membrane electrode assembly (MEA) fabrication on the PEMFC performance. Here, we discuss here some remarkable performance improvements recently achieved by tuning catalyst loading, ionomer content, and ink solvent composition, and call for further explorations of the ink processing and MEA fabrication to improve performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Surface reaction for efficient and stable inverted perovskite solar cells

We report perovskite solar cells (PSCs) with an inverted structure (often referred to as the p-i-n architecture) are attractive for future commercialization due to their easily scalable fabrication, reliable operation, and compatibility with a wide range of perovskite-based tandem device architectures. However, the power conversion efficiency (PCE) of p-i-n PSCs falls behind n-i-p (or normal) structure counterparts. This large performance gap could undermine efforts to adopt p-i-n architectures, despite their other advantages. Given the remarkable advances in perovskite bulk materials optimization over the past decade, interface engineering has become the most important strategy to push PSC performance to its limit. Here, we report a reactive surface engineering approach based on a simple post-growth treatment of 3-(Aminomethyl)pyridine (3-APy) on top of a perovskite thin film. First, the 3-APy molecule selectively reacts with surface FA+, reducing perovskite surface roughness and surface potential fluctuations associated with surface steps/terraces. Second, the reaction product on the perovskite surface decreases the formation energy of charged iodine-vacancies, leading to effective n-type doping with a reduced work function in the surface region. With this reactive surface engineering, the resulting p-i-n PSCs obtained a PCE over 25%, along with retaining 87% of the initial PCE after over 2400 h of one-sun operation at about 55 degrees C in air.

14 SOLAR ENERGY↗