Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CIRCULAR PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

An experimental study of the initiation and progression of damage in compressively loaded composite laminates in the presence of a circular cutout

Experiments have been carried out on T300/BP907 and IM7/8551-7 graphite/epoxy laminates in an attempt to understand the mechanisms for the initiation and spread of damage in compressively loaded composite laminates containing a circular jutout. Based on the results of holographic interferometry, in-situ photomicrography, and strain measurements, it is found that the failure is initiated by fiber microbuckling in the 0-deg plies. This failure gradually develops as the hole surface in the form of a fiber jutout failure. Subsequent to the 0-deg ply failure, extensive delamination cracking is observed with increasing load, eventually leading to the catastrophic failure of the plate.

Waas, A. M.↗

Analysis of a disk-on-rod surface wave element inside a corrugated horn using the mode-matching technique

A disk-on-rod inside a corrugated horn is one of the horn configurations for dual-frequency or wide-band operation. A mode-matching analysis method is described. A disk-on-rod inside a corrugated horn is represented as a series of coaxial waveguide sections and circular waveguide sections connected to each other. Three kinds of junctions need to be considered: coaxial-to-coaxial, coaxial-to-circular, and circular-to-circular. A computer program was developed to calculate the scattering matrix and the radiation pattern of a disk-on-rod inside a corrugated horn. The software as verified by experiment, and good agreement between calculation and measurement was obtained. The disk-on-rod inside a corrugated horn design gives an option to the Deep Space Network dual-frequency operation system, which currently is a two-horn/one-dichroic plate system.

Chen, J. C.↗

Free-Flight Investigation of a Rocket-Propelled Model to Determine the Aerodynamic Heating on a Thin, Unswept, Untapered, Multispar, Aluminum-Alloy Wing at Mach Numbers up to 2.22

A free-flight investigation has been made to determine some effects of aerodynamic heating on the structural behavior of a wing at supersonic speeds. The test wing was a thin, unswept, untapered, multispar, aluminum-alloy wing having a 20-inch chord, a 20-inch exposed semispan, and a circular-arc airfoil section with a thickness ratio of 5 percent. The wing was tested on a model propelled by a two-stage rocket-propulsion system to a Mach number of 2.22 and a corresponding Reynolds number per foot of 13.2 x 10(6) Reasonably good agreement was obtained between Stanton numbers obtained from measured temperature-time data and values obtained by the theory of Van Driest for flat plates having turbulent boundary layers. Temperature measurements made in the skin of the wing and in the internal structures agreed well with calculated values. The wing was instrumented to detect any apparent fluttering motion in the wing, but no evidence of flutter was observed throughout the flight.

Stephens, Emily W.↗

Development and verification of methods for predicting flow rates through leaks in valves and couplings

This is the final report of a research effort which addresses the title problem. The report discusses two broad models of flows, which represent the following extreme cases: (1) inertia-dominated flow, where friction is relatively insignificant; and (2) friction-dominated flow where inertia is insignificant. In class (2), the leak channel might consist of the gap between a scratch in a plastic seal and a polished metal plate against which the seal is pressed. Here, the cross section of the leak channel is modeled as a flat bottomed crescent. A publication generated under the present grant period presents an exact solution of the equations of fully-developed laminar pipe flow of a liquid in the case of a crescent beneath a hyperbolic arc. A Master's thesis project supported by the present grant presents the corresponding solution beneath a circular arc. A second publication reviews the flow of a gas through the same channel, which may be analyzed by a standard one-dimensional model (Fanno flow) for an engineering approximation. Finally, the report discusses the design and progress in the fabrication of a leak-test cell, in which one may measure the flow of fluid through a controlled flaw in a seal. The aim of such measurements is to furnish data for comparison with the predictions of the theory.

Russell, John M.↗

Pulsed-echo interface wave characterization of bolted plates

Ultrasonic waves which propagate along the plane boundary separating two solid substrates were used to characterize aluminum and titanium plates adhesively bonded and bolted together. Wave pulses were used to produce interface waves between the aluminum and a Ti-6Al-4V titanium alloy bar by normal mode conversion. Interface wave reflections from bolt holes drilled through the interface were reconverted to surface wave pulses and detected by the same wedge by standard pulse-echo techniques. Time of flight measurements indicate that the reflected waves are a supersonic of longitudinal modes and circularly symmetric waves that propagate around the bolt hole.

Turner, T. M.↗

Transonic shock-induced dynamics of a flexible wing with a thick circular-arc airfoil

Transonic shock boundary layer oscillations occur on rigid models over a small range of Mach numbers on thick circular-arc airfoils. Extensive tests and analyses of this phenomena have been made in the past but essentially all of them were for rigid models. A simple flexible wing model with an 18 pct. circular arc airfoil was constructed and tested in the Langley Transonic Dynamics Tunnel to study the dynamic characteristics that a wing might have under these circumstances. In the region of shock boundary layer oscillations, buffeting of the first bending mode was obtained. This mode was well separated in frequency from the shock boundary layer oscillations. A limit cycle oscillation was also measured in a third bending like mode, involving wind vertical bending and splitter plate motion, which was in the frequency range of the shock boundary layer oscillations. Several model configurations were tested, and a few potential fixes were investigated.

Bennett, Robert M.↗

Finite elements modelling of scattering problems for flexural waves in thin plates: Application to elliptic invisibility cloaks, rotators and the mirage effect

We propose a finite elements algorithm to solve a fourth order partial differential equation governing the propagation of time-harmonic bending waves in thin elastic plates. Specially designed perfectly matched layers are implemented to deal with the infinite extent of the plates. These are deduced from a geometric transform in the biharmonic equation. To numerically illustrate the power of elastodynamic transformations, we analyze the elastic response of an elliptic invisibility cloak surrounding a clamped obstacle in the presence of a cylindrical excitation i.e. a concentrated point force. Elliptic cloaking for flexural waves involves a density and an orthotropic Young's modulus which depend on the radial and azimuthal positions, as deduced from a coordinates transformation for circular cloaks in the spirit of Pendry et al. [Science 312, 1780 (2006)], but with a further stretch of a coordinate axis. We find that a wave radiated by a concentrated point force located a couple of wavelengths away from the cloak is almost unperturbed in magnitude and in phase. However, when the point force lies within the coating, it seems to radiate from a shifted location. Finally, we emphasize the versatility of transformation elastodynamics with the design of an elliptic cloak which rotates the wavevector of a flexural wave within its core.

97 MATHEMATICS AND COMPUTING↗

Evaluation of a composite mobile holographic nondestructive test system

A simplified theoretical model for the interpretation of the double-exposure holographic interference fringe loci due to the general three-dimensional displacements was derived for the specific composite mobile holographic nondestructive test system. The model, representing a good approximation to a more tedious theoretical result, predicts that a combination of in-plane and out-of-plane displacements of the surface will produce concentric circular-shaped fringe patterns with locations of their center affected by the displacements. Appropriate experiments were designed and carried out for the test of the validity of the theory. These experiments include the taking of double-exposure holograms of in-plane translations and combined in-plane and out-of-plane translations. The simplified model agreed quite well with the experimental results. Experimentally observed effects due to the curvature of the test plate and the variations of the angles of incidence of the laser light suggest that in order for the simplified model to be able to predict the test results more accurately, incidence and reflection of the laser light should be chosen as nearly perpendicular to the surface of the tested object as possible.

Liu, H. K.↗

Transonic shock-induced dynamics of a flexible wing with a thick circular-arc airfoil

A simple flexible wing model with an 18-percent circular arc airfoil was constructed and tested in the Langley Transonic Dynamics Tunnel to investigate the dynamic characteristics that a wing might have under these conditions. In the region of shock-boundary layer oscillations, buffeting of the first bending mode was obtained. This mode was well separated in frequency from the shock boundary layer oscillations. A limit cycle oscillation was also measured in a 'third bending-like' mode, involving wing vertical bending and splitter plate motion, which was in the frequency range of the shock-boundary layer oscillations. Several model configurations were tested, and a few potential fixes were investigated.

Bennett, Robert M.↗

Developing Procedures to Implement Geometric Imperfections Beyond Right Circular Cylindrical Shells in Finite Element Method Models

Analysis of aerospace structures is frequently conducted using nominal dimensions and frequently assumes ideal conditions in loading, contact, constraints, et cetera. Off-nominal dimensions and nonideal conditions, however, are present in all structures. These are the result of widely ranging causes from coefficient of thermal expansion mismatches, manufacturing tooling anomalies, to assembly procedures that inadvertently alter the structure. Specifically, geometric imperfections can have potentially significant influence on the response of a structural test article observed in an experiment versus the response given by a numerical simulation. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS) was previously presented as a set of Python scripts to calculate and implement as-manufactured geometric midsurface and thickness imperfections into finite element method (FEM) shell models of nominally right circular cylinders. By taking advantage of the simple shape of a right circular cylinder, interpolations of the measured data points were able to be performed along directions that aligned to the cylindrical coordinate system axes of the entire structure. By taking advantage of the shell representation of the real structure as opposed to modeling using a continuum representation, the thickness variation was able to be implemented by shell section definitions instead of having to modify the position of multiple nodes in the thickness direction. Py_TIGIRS is a useful tool that established a procedural example on how to implement geometric imperfections in right circular cylindrical shell structures. Three new procedures, each expanded from concepts established in Py_TIGIRS, are proposed for various test-article designs and are intended to broaden the range of structures that can be modeled with measured geometric imperfections in the structural analysis community. Each test-article design introduces new challenges to successfully implement geometric imperfections into a FEM model. The first test-article design consists of a carbon fiber reinforced polymer square plate with a hat-shaped stiffener co-cured on one side. This test-article design was for a novel seven-point bend test that was also previously presented. Manufacturing and cure-cycle imperfections are observed using digital image correlation (DIC) techniques. As thermal expansion coefficient mismatches between the plate and stiffener materials were anticipated, a thermal analysis study with continuum shell and solid elements was conducted to capture the global shape observed prior to testing. The second test-article design is of a similar hat-stiffened plate configuration, but with a side length ratio near 3:1 with elongation in the stiffener direction. The test article was used to characterize the response to uniaxial compressive loading in the direction of the stiffener. Due to differing manufacturing steps, a thermal analysis like the one developed for the seven-point bend configuration was unable to mimic the observed geometric imperfections. Instead, a strategy based on applying deformations directly to the structure during analysis was developed for continuum shell and solid element representation of a stiffened panel.

Geometric imperfections↗

Viscous boundary layers in rotating fluids driven by periodic flows

The paper analyzes the boundary layers formed in a rotating fluid by an oscillating flow over an infinite half plate, with particular attention paid to the effects of unsteadiness, the critical latitude effect and the structure of the solution to the boundary layer equations at resonance. The Navier-Stokes boundary layer equations are obtained through an asymptotic expansion with the incorporation of the Rossby and Ekman numbers and are analyzed as the sum of a nonlinear steady solution and a linearized unsteady solution. The solution is predominantly composed of two inertial wave vector components, one circularly polarized to the left and the other circularly polarized to the right. The problem considered here has relevance in oceanography and meteorology, with special reference to the unsteady atmospheric boundary layer.

Bergstrom, R. W.↗

Laser Image Contrast Enhancement System

An optical image enhancement system provides improved image contrast in imaging of a target in high temperature surroundings such as a furnace. The optical system includes a source of vertically polarized light such as laser and a beam splitter for receiving the light and directing the light toward the target. A retardation plate is affixed to a target-facing surface of the beam splitter and a vertical polarizer is disposed along a common optical path with the beam splitter between the retardation plate and the target. A horizontal polarizer disposed in the common optical path, receives light passing through a surface of the beam splitter opposed to the target-facing surface. An image detector is disposed at one end of the optical path. A band pass filter having a band pass filter characteristic matching the frequency of the vertically polarized light source is disposed in the path between the horizontal polarizer and the image detector. The use of circular polarization, together with cross polarizers, enables the reflected light to be passed to the detector while blocking thermal radiation.

Robert L Kurtz↗

Gratings Fabricated on Flat Surfaces and Reproduced on Non-Flat Substrates

A method has been developed for fabricating gratings on flat substrates, and then reproducing the groove pattern on a curved (concave or convex) substrate and a corresponding grating device. First, surface relief diffraction grating grooves are formed on flat substrates. For example, they may be fabricated using photolithography and reactive ion etching, maskless lithography, holography, or mechanical ruling. Then, an imprint of the grating is made on a deformable substrate, such as plastic, polymer, or other materials using thermoforming, hot or cold embossing, or other methods. Interim stamps using electroforming, or other methods, may be produced for the imprinting process or if the same polarity of the grating image is required. The imprinted, deformable substrate is then attached to a curved, rigid substrate using epoxy or other suitable adhesives. The imprinted surface is facing away from the curved rigid substrate. As an alternative fabrication method, after grating is imprinted on the deformable substrate as described above, the grating may be coated with thin conformal conductive layer (for example, using vacuum deposition of gold). Then the membrane may be mounted over an opening in a pressured vessel in a manner of a membrane on a drum, grating side out. The pressure inside of the vessel may be changed with respect to the ambient pressure to produce concave or convex membrane surface. The shape of the opening may control the type of the surface curvature (for example, a circular opening would create spherical surface, oval opening would create toroidal surface, etc.). After that, well-known electroforming methods may be used to create a replica of the grating on the concave or convex membrane. For example, the pressure vessel assembly may be submerged into an electro-forming solution and negative electric potential applied to the metal coated membrane using an insulated wire. Positive electric potential may be then applied to a nickel or other metal plate submerged into the same solution. Metal ions would transfer from the plate through the solution into the membrane, producing high fidelity metal replica of the grating on the membrane. In one variation, an adhesive may be deposited on the deformable substrate, and then cured without touching the rigid, curved substrate. Edges of the deformable substrate may be attached to the rigid substrate to ensure uniform deformation of the deformable substrate. The assembly may be performed in vacuum, and then taken out to atmospheric pressure conditions to ensure that no air is trapped between the deformable and rigid substrates. Alternatively, a rigid surface with complementary curvature to the rigid substrate may be used to ensure uniform adhesion of the deformable substrate to the rigid substrate. Liquid may be applied to the surface of the deformable substrate to uniformly distribute pressure across its surface during the curing or hardening of the adhesive, or the film may be pressed into the surface using a deformable object or surface. After the attachment is complete, the grooves may be coated with reflective or dielectric layers to improve diffraction efficiency.

Content, David↗

Antenna surface contour control system

The invention is a system for automatically controlling the surface contour of a deployable and restowable antenna having a mesh reflector surface supported by a circular, folding hoop affixed to a central, telescoping column. The antenna, when deployed, forms a quad-aperture reflector with each quadrant of the mesh surface shaped to provide an offset parabolic radio frequency (RF) reflector. The hoop is supported and positioned by quartz support cords attached to the top of a column and by lower graphite hoop control cords that extend between the hoop and base of the column. The antenna, an RF reflective surface, is a gold plated molybdenum wire mesh supported on a graphite cord truss structure that includes the hoop control cords and a plurality of surface control cords attached at selected points on the surface and to the base of the column. The contour of the three-dimensional surface of the antenna is controlled by selectively adjusting the lengths of the surface control cords and the graphite hoop control cords by means of novel actuator assemblies that automatically sense and change the lengths of the lower hoop control cords and surface control cords.

Elvin L Ahl↗

Lunar Reconnaissance Orbiter Orbit Determination Accuracy Analysis

Results from operational OD produced by the NASA Goddard Flight Dynamics Facility for the LRO nominal and extended mission are presented. During the LRO nominal mission, when LRO flew in a low circular orbit, orbit determination requirements were met nearly 100% of the time. When the extended mission began, LRO returned to a more elliptical frozen orbit where gravity and other modeling errors caused numerous violations of mission accuracy requirements. Prediction accuracy is particularly challenged during periods when LRO is in full-Sun. A series of improvements to LRO orbit determination are presented, including implementation of new lunar gravity models, improved spacecraft solar radiation pressure modeling using a dynamic multi-plate area model, a shorter orbit determination arc length, and a constrained plane method for estimation. The analysis presented in this paper shows that updated lunar gravity models improved accuracy in the frozen orbit, and a multiplate dynamic area model improves prediction accuracy during full-Sun orbit periods. Implementation of a 36-hour tracking data arc and plane constraints during edge-on orbit geometry also provide benefits. A comparison of the operational solutions to precision orbit determination solutions shows agreement on a 100- to 250-meter level in definitive accuracy.

Gravitation↗

Analytical Modal Analysis for Thin-Film Flat Lenses

Due to strong potential applications and more demanding requirements imposed upon thin-film structures for space deployable, there has been increasing research and development activities during recent years in the field of vibration analysis of these types of structures. Moreover, interests in employing these structural components have received renewed emphasis in recent years within NASA and the Air Force. This is due to their inherent lightweight, low packaging and launch volume, and relative simplicity of deployment. Among the potential mission concepts for which these structural elements are included, one can mention solar sails, space solar power generation systems, solar thermal propulsion vehicles, large space telescopes, and inflatable communication antennas. This paper presents analytical procedures to determine vibration and physical characteristics of thin film lenses with circular and elliptical shapes membranes considered in design of a solar concentrator. In general, three methods are used to obtain approximate solutions of Helmholtz boundary value problems. One method requires that solution satisfy the differential equation exactly and the boundary condition approximately. Another method demands a solution that satisfies the boundary conditions exactly and the governing equations approximately. The third method sees a solution that satisfies both the governing equation and boundary conditions approximately. Extensive reviews of vibrations of membrane and plates are provided by Leissa and Mazumdar.

Hamid R. Hamidzadeh↗

Vortex motion behind a circular cylinder

Vortex motion behind a circular cylinder moving through water is discussed. It is shown that a pair of vortices form behind a moving cylinder and that their centers will move along a predictable curve. This curve represents an equilibrium condition which, however, is subject to perturbation. The stability of the vortex pair is investigated. Movement of the vortex pair away from the cylinder is calculated as an explanation of the resistance of the cylinder. Finally, the principles elaborated are applied to the flow around a flat plate.

Foeppl, L.↗

Bundled tube fuel nozzle assembly with liquid fuel capability

A bundled tube fuel nozzle assembly includes a fuel injector and a tube bundle comprising a plurality of tubes that provide for fluid communication through a forward plate, a fuel plenum and an aft plate of the bundled tube fuel nozzle assembly. Each tube includes an inlet defined at an upstream end of the tube and an outlet defined at a downstream end of the tube. The fuel injector is disposed upstream from the inlets of each of the tubes. The upstream end of each tube is noncircular and includes at least one side portion that abuts a complementary upstream end side portion of an immediately adjacent tube of the plurality of tubes. The downstream end of each tube may be circular and is spaced apart from the downstream ends of immediately adjacent tubes of the plurality of tubes.

42 ENGINEERING↗