SEARCH · Engineering Papers

Results for “CHAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

All sources NASA NTRS DOE OSTI

NASA NTRS2017

3D Material Response Analysis of PICA Pyrolysis Experiments

The PICA decomposition experiments of Bessire and Minton are investigated using 3D material response analysis. The steady thermoelectric equations have been added to the CHAR code to enable analysis of the Joule-heated experiments and the DAKOTA optimization code is used to define the voltage boundary condition that yields the experimentally observed temperature response. This analysis has identified a potential spatial non-uniformity in the PICA sample temperature driven by the cooled copper electrodes and thermal radiation from the surface of the test article (Figure 1). The non-uniformity leads to a variable heating rate throughout the sample volume that has an effect on the quantitative results of the experiment. Averaging the results of integrating a kinetic reaction mechanism with the heating rates seen across the sample volume yield a shift of peak species production to lower temperatures that is more significant for higher heating rates (Figure 2) when compared to integrating the same mechanism at the reported heating rate. The analysis supporting these conclusions will be presented along with a proposed analysis procedure that permits quantitative use of the existing data. Time permitting, a status on the in-development kinetic decomposition mechanism based on this data will be presented as well.

Oliver, A. Brandon↗

NASA NTRS2017

Results of Large-Scale Spacecraft Flammability Tests

For the first time, a large-scale fire was intentionally set inside a spacecraft while in orbit. Testing in low gravity aboard spacecraft had been limited to samples of modest size: for thin fuels the longest samples burned were around 15 cm in length and thick fuel samples have been even smaller. This is despite the fact that fire is a catastrophic hazard for spaceflight and the spread and growth of a fire, combined with its interactions with the vehicle cannot be expected to scale linearly. While every type of occupied structure on earth has been the subject of full scale fire testing, this had never been attempted in space owing to the complexity, cost, risk and absence of a safe location. Thus, there is a gap in knowledge of fire behavior in spacecraft. The recent utilization of large, unmanned, resupply craft has provided the needed capability: a habitable but unoccupied spacecraft in low earth orbit. One such vehicle was used to study the flame spread over a 94 x 40.6 cm thin charring solid (fiberglasscotton fabric). The sample was an order of magnitude larger than anything studied to date in microgravity and was of sufficient scale that it consumed 1.5 of the available oxygen. The experiment which is called Saffire consisted of two tests, forward or concurrent flame spread (with the direction of flow) and opposed flame spread (against the direction of flow). The average forced air speed was 20 cms. For the concurrent flame spread test, the flame size remained constrained after the ignition transient, which is not the case in 1-g. These results were qualitatively different from those on earth where an upward-spreading flame on a sample of this size accelerates and grows. In addition, a curious effect of the chamber size is noted. Compared to previous microgravity work in smaller tunnels, the flame in the larger tunnel spread more slowly, even for a wider sample. This is attributed to the effect of flow acceleration in the smaller tunnels as a result of hot gas expansion. These results clearly demonstrate the unique features of purely forced flow in microgravity on flame spread, the dependence of flame behavior on the scale of the experiment, and the importance of full-scale testing for spacecraft fire safety.

microgravity↗

NASA NTRS2019

Charactarization of Thermal Protection Systems

In 2012, NASA's mission of landing the Mars Science Laboratory (MSL) on Mars was successful. MSL was protected by an ablative heatshield of tiled low density material known as PICA (phenolic impregnated carbon ablator). The heatshield was instrumented with MEDLI (MSL Entry Descent Landing Instrument) a suite of sensors & thermocouples at discrete locations in order to monitor the in-depth ablator temperature response and surface pressure. MEDLI was designed and developed by NASA Langley, in partnership with NASA Ames Research Center for the purposes of probing Mars and evaluating the performance of the spacecraft upon entry into the Martian atmosphere. The flight data reduces the uncertainty in engineer models for predicting the response of a spacecraft towards the extreme heating environment of an entry into the Martian atmosphere. MEDLI2 is a part of the Mars 2020 mission and is the next-generation sensor suite for entry, descent, and landing. This data will again help engineers validate their flight models. Additionally, the atmospheric data, can help us understand atmospheric density and winds. This is a critical study for reducing risks to both robotic and future human missions to Mars. Engineered models for Mars 2020 are dependent upon parameters related to the materials response to heating and radiation. In this work, the thermal properties and other measurements of various ablative materials are analyzed to achieve greater utility of the 2012 MEDLI flight data and more accurately determine the parameters being used in Mars 2020. The purpose of this study was to measure specific heat, thermal conductivity, char yield, reflectance as a function of wavelength, and other thermal parameters and optical properties of various ablative materials. CO2(g) at extreme temperatures emits radiation impacting MEDLI2 flight predictions. Emissivity & absorptivity as a function of temperature were calculated from FTIR and UV-Vis data as a means of investigating whether these materials might absorb CO2 radiation upon entry into the Mars atmosphere.

HEEET↗

NASA NTRS2019

Heatshield Erosion Due to Dust Particle Impacts on the Schiaparelli Capsule During Martian Entry

One of the unique features of spacecraft entering the atmosphere of Mars is the possibility of a major dust storm occurring during the entry. Design of the thermal protection system (TPS) for Mars missions have to account for the possibility of dust erosion when estimating the thickness of the TPS. Because weight is always a critical factor in designing entry vehicles, accurate assessment of dust erosion is necessary to avoid over-design of the TPS.This study will present computational results of heatshield erosion due to dust particle impacts on the ExoMars Schiaparelli capsule if it had encountered a dust storm during its October 2016 entry. A one-way coupling approach is used where particle trajectories are computed based on an underlying CFD flow solution. Based on a distribution of particle sizes ranging from 1 to 18 microns in diameter, the Icarus material response solver predicted approximately 1 mm of TPS heatshield erosion due to particle impacts, which was 40% of the value due to material charring.

thermal protection system↗

NASA NTRS2019

Modeling Heatshield Erosion Due to Dust Particle Impacts for a Martian Entry Vehicle

The modeling assumptions and governing equations required to estimate the heatshield surface recession due to dust particle impacts are presented. The dust particle size distribution can be estimated using a modified gamma distribution. The vertical distribution of dust particles in the atmosphere in terms of the ratio of dust particle to atmospheric density can be related to measured or computed values of the dust opacity. The different approaches to coupling the particle and fluid dynamics are discussed. The equations and modeling assumptions presented in this paper are applied to computing the surface recession due to dust particle impacts on the ExoMars Schiaparelli capsule entering the Martian atmosphere during a representative dust storm. The dust surface recession at the stagnation point of about 1 millimeter is about 40 percent of the recession value due to charring ablation.

Thermal Protection Systems↗

NASA NTRS2020

Orbital Debris: Quarterly News, April 2020

Inside - New NASA Orbital Debris Engineering Model ORDEM 3.1 - Composite Material Char Rate and Strength Retention Study at University of Texas Austin - Conference and Meeting Reports - Space Missions and Satellite Box Score

Orbital Debris Engineering Model↗

NASA NTRSDate not supplied

ANALYSIS OF THE MSL/MEDLI ENTRY DATA WITH COUPLED CFD AND MATERIAL RESPONSE.

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heat-shield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material. PICA is a lightweight carbon fiber/polymeric resin material that offers out-standing performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP). The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on Open-FOAM (PATO) using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA, is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Mars Science Laboratory↗

NASA NTRSDate not supplied

MEDLI2: Ablator Models for Flight

During the entry of Mars Science Laboratory (MSL) the heatshield was equipped with the instrumentation suite Mars Entry, Descent, and Landing Instruments (MEDLI). In-depth thermocouple (TC) data was used to reconstruct the surface heating[1,2]. Discrepancies between MEDLI’s flight heating data and predicted thermal response and recession[3] led to a campaign to characterize and test Mars2020 and MEDLI2 (Mars Entry, Descent, and Landing Instrument 2)[4] flight-lot thermal protection materials (TPS) at relevant ground test conditions. This paper covers the development and validation of flight-lot material response models for the heatshield material Phenolic Impregnated Carbon Ablator (PICA) and the backshell material SLA-561V (Super Lightweight Ablator). Virgin and char properties such as thermal conductivity and emissivity were updated as a function of temperature and pressure in the MEDLI2 specific material response models. Other material properties were characterized and determined to be similar to prior TPS material measurements used for the heritage models. MEDLI2 also investigated the impact of the protective coating that was applied to MSL and Mars2020’s PICA heatshield to reduce the particulate matter shedding. Evidence from arc jet experiments on coated PICA showed that although there were no adverse effects on the performance of the TPS, there were differences in the in-depth temperatures and reduced recession compared to material response predictions of uncoated PICA.[5,6]. Fully Implicit Ablation and Thermal response (FIAT)[7] material response simulations were conducted with the heritage and MEDLI2 flight-lot material models. FIAT-predicted in-depth temperature responses and recession predictions were compared to flight-lot certification ground-test arc jet test data and MEDLI2 thermocouple data.

Materials Response↗

NASA NTRSDate not supplied

Analysis of MSL/MEDLI Entry Data with Coupled CFD and Material Response

The Mars Science Laboratory (MSL) was protected during its atmospheric entry by an instrumented heatshield using NASA's Phenolic Impregnated Carbon Ablator (PICA) material [1]. PICA is a lightweight carbon fiber/polymeric resin material that offers outstanding performances for protecting probes during planetary entry. The Mars Entry Descent and Landing Instrument (MEDLI) suite on MSL offers unique in-flight validation data for models of material response and atmospheric entry. MEDLI recorded, among other things, time-resolved in-depth temperature data of PICA using thermocouple sensors assembled in the MEDLI Integrated Sensor Plugs (MISP) [2]. The objective of this work is to showcase and analyze the coupling between the material response and the aerothermal environment. As shown in Figure 1, the workflow is divided into the following steps. First, the aerothermal properties are computed in the Data Parallel Line Relaxation (DPLR) code [3] and used with the Nonequilibrium air radiation (NEQAIR) program [8] to compute radiative heating. Second, the thermal response inside the material is computed in the Porous material Analysis Toolbox based on OpenFOAM (PATO) [4,5,6] using a fixed blowing correction parameter. Third, the pyrolysis gases computed in PATO are used as inputs to a blowing boundary condition within DPLR. Fourth, the new environment properties from DPLR are used in NEQAIR to provide an updated solution, then both the updated aerothermal environment and radiative heating are used in PATO without blowing correction. The third and fourth steps are then repeated until convergence in surface temperature is obtained. Convergence in the radiative heating is generally achieved before surface temperature, at which point the radiative heating is no longer updated. Char mass loss rates are forced to zero to produce a non-receding surface condition. For early time points in the trajectory, where flow around the MSL aeroshell is rarefied, the Direct Simulation Monte Carlo (DSMC) code, SPARTA [7], is used to compute the aerothermal environment. Iteration between PATO and SPARTA is not performed due to the computational cost of DSMC simulations. Preliminary results of the coupling between PATO and DPLR for the MSL heatshield atmospheric entry model are presented in Figures 2-4 at 65 seconds after entry interface. Figure 2 shows the surface temperature results from an uncoupled simulation in PATO with the blowing correction parameter applied (left) along with the coupled surface temperature after iteration (right). Figure 3 shows the surface temperature along the centerline from windward to leeward for easier comparison. Figure 4 shows the coupled and uncoupled pyrolysis gas blowing rate. Mars 2020 used a similar heatshield consisting of PICA for thermal protection during entry, descent, and landing. In preparation for Mars 2020 post-flight analysis, the predictive material response capability is benchmarked against flight data from MEDLI. This work represents an important milestone toward the development of validated predictive capabilities for designing thermal protection systems for planetary probes.

Thermal Protection Systems↗

NASA NTRSDate not supplied

Analysis of PICA-NuSil at the Hypersonic Materials Environmental Test System (HyMETS)

Phenolic Impregnated Carbon Ablator (PICA) gained heritage during the stardust mission and is the baseline material for missions to Mars. The phenolic phase of PICA is friable, and therefore the surface is treated with a siloxane resin (NuSil) to mitigate the shedding of particulate matter. Historically, material response models have not accounted for the presence of this coating. Therefore, a test campaign was executed at the Hypersonic Materials Environmental Test System (HyMETS) to investigate the performance of NuSil under multiple heating rates and gas composition. Sphere-cone models were instrumented with thermocouples to measure the in-depth temperature response, and surface temperatures were monitored with a pyrometer. Furthermore, emission spectrometers were used to collect spectra from species emitting at the surface of the test article and the post-shock stagnation region. Post-test analysis suggests that the coating decomposes according to multiple stages. Inspection of silicon emission data reveals a rapid rise and decline in intensity within the first couple of seconds of testing, which is attributed to pyrolysis of NuSil. Pyrolysis is followed by a stagnation in silicon emission and surface temperature which are attributed to the formation of a thin layer of oxidation-resistant silicon oxycarbide. Moreover, the presence of the silicon oxycarbide layer significantly reduces the in-depth thermal response when compared to the baseline material. Eventually, the silicon oxycarbide layer decomposes via high-temperature reactions, which expose the underlying char layer to a highly reactive flow.

PICA-NuSil↗

NASA NTRSDate not supplied

Coupling CFD and Material Response for Analysis of Mars Entry

In computing the response of an ablating thermal protection system during atmospheric entry, the aerothermal environment and material response are generally computed separately with a blowing correction term in the material response model to account for the blowing of char and pyrolysis gases [1]. In this work, we apply a coupled approach in which pyrolysis blowing gases, computed in the PATO material response code [2], are used with a blowing boundary condition in the DPLR hypersonic CFD code [3]. This leads to an iterative method in which blowing products from PATO are input into DPLR to update surface heating estimates. The full iterative method, with the addition of radiative heating estimates using the NEQAIR radiation solver [4], is shown in Fig. 1. The method is demonstrated on a sphere case with the environment and material properties based on the Mars Science Laboratory entry. Future work includes utilizing this method in computing full 3D material response during the Mars 2020 entry.

Heat Transfer↗

NASA NTRSDate not supplied

Analysis of Pyrolysis Products from Ablative Thermal Protection Systems

NASA’s state-of-the-art ablative materials are composed of a three-dimensional network of carbon fibers impregnated with polymers that dissipate thermal energy through pyrolysis. A fundamental understanding of the decomposition mechanisms and pyrolysis product distributions of various classes of polymers is instrumental in the design of new ablative materials. Furthermore, innovative experiments are essential to the continuous modernization of material response models by providing high-fidelity data. Thus, an apparatus has been designed to measure pyrolysis products from polymers and composite materials by implementing in-situ mass spectrometric techniques. Initial results from experiments performed on siloxane resins and a common phenolic resin will be discussed. Both classes of polymers exhibit heating-rate-dependent decomposition mechanisms. At the onset of heating, phenolic polymers decompose through competitive reactions to form gaseous products and a carbonaceous char. Gas phase products of phenolic resins are typically composed of molecular hydrogen, water, and aromatic hydrocarbons. Pyrolysis products from siloxane polymers include molecular hydrogen, small molecules, and cyclic oligomers from the polymer backbone.

Pyrolysis↗

NASA NTRSDate not supplied

A Combined CFD/Material Response Analysis of 3MDCP Arcjet Experiments

The Mars Sample Return Earth Entry System (MSR-EES) project has selected 3-D Woven Mid-Density Carbon Phenolic (3MDCP) as the baseline thermal protection system (TPS) material for the capsule that will return Martian soil samples to Earth sometime in the 2030’s. A series of experiments in the NASA Ames AHF and IHF arcjets will be used to characterize the performance of 3MDCP and to develop and refine material response models for it. The test objectives for these experiments include obtaining in-depth and surface temperature data, mass loss and surface recession measurements, and char depth measurements. To provided pre- and post-test support for the arcjet experiments, a combined CFD/material response was performed using the DPLR and Icarus code. Pre-and post-test analysis on the 3MDCP arcjet experiments was performed using the DPLR CFD and Icarus material response codes. The codes were not tightly coupled, but boundary condition data required by Icarus (e.g., heat transfer coefficients and surface pressures), were extracted from the CFD solutions. This poster shows comparisons between DPLR/Icarus and the experimental data taken during arcjet experiment AHF-348 where 4-inch diameter iso-q models made from 3MDCP were tested in the 12-inch nozzle of the AHF arcjet. This poster also includes a top-level overview of the CFD/material response arcjet simulation process. Best-practices for running CFD solutions of arcjet experiments including how to determine the inflow conditions for the CFD solution from the arc heater settings are discussed. The required inputs to the material response solver are presented, as well as a discussion of how they can be extracted from the CFD solution.

thermal protection systems↗

NASA NTRSDate not supplied

Coupling CFD and Material Response for Analysis of Mars Entry

In computing the response of an ablating thermal protection system during atmospheric entry, the aerothermal environment and material response are generally computed separately with a blowing correction term in the material response model to account for the blowing of char and pyrolysis gases. In this work, we apply a coupled approach in which pyrolysis blowing gases, computed in the PATO material response code, are used with a blowing boundary condition in the DPLR hypersonic CFD code. This leads to an iterative method in which blowing products from PATO are input into DPLR to update surface heating estimates. The full iterative method, with the addition of radiative heating estimates using the NEQAIR radiation solver, is shown in Fig. 1. The method is demonstrated on a sphere case with the environment and material properties based on the Mars Science Laboratory entry. Future work includes utilizing this method in computing full 3D material response during the Mars 2020 entry.

Ablation↗

NASA NTRSDate not supplied

Efficient Parametric Uncertainty Analysis of an Earth Entry Vehicle Concept Using Least Angle Regression

The objective of this work was to outline and apply an efficient and accurate parametric un-certainty propagation approach to the analysis of convective heating on an Earth entry vehicle concept. The described approach was based on Least Angle Regression used to solve a sparse and underdetermined linear system in the point-collocation non-intrusive polynomial chaos surrogate method. This approach involved an iterative process to computing the non-zero terms of the underlying polynomial chaos model using only enough samples to converge uncertainty interval predictions and Sobol index values based global nonlinear sensitivity estimates. The Earth entry vehicle was analyzed at three points along a representative trajectory for a Mars return mission. 329 sources of uncertainty were identified in the computational fluid dynamics model used to predict the forebody convective heating. These included uncertainty in flow field chemical rates, collision integrals, heats of formation, surface finite rate char model reaction rates, wall roughness height, and the turbulent Schmidt number. Results from this study showed that convective heating uncertainty as high as 50% of the nominal was predicted with only about 50 evaluations of the computational model. This was far fewer than would be required for a sampling-based approach or a full basis polynomial chaos model, which would have required over 50,000 samples. Additionally, results showed that over 90% of the total convective heating uncertainty was due to uncertainty in the N2catalytic rate on the surface, while the remainder of the uncertainty was attributed to the turbulent Schmidt number and the wall roughness uncertainties.

Thomas K West IV↗

NASA NTRSDate not supplied

Analysis of Pyrolysis Products from Ablative TPS

Pyrolysis↗

NASA NTRS2019

Experimental Measurements of the High-Temperature Oxidation of Carbon Fibers

We carried out laboratory experiments to study the decomposition of carbon fibers at high temperature and studied the material used in charring carbon phenolic ablators for planetary probe heatshields. Porous plug samples were exposed to controlled rates of molecular oxygen, carbon dioxide, and carbon monoxide at furnace-heated flow-tube reactor temperatures between 700 and 1500 K and pressures between 2000 and 6200 Pa. We used calibrated mass spectroscopy to make time-resolved quantitative measurements of decomposition products of the gases downstream of the test sample. Absolute and differential pressure measurements were used to determine the high-temperature permeability of the material and to monitor changes during material decomposition, and we characterized the microstructure of the porous sample using scanning electron microscopy. We found substantial carbon fiber oxidation for O2 flows, resulting in increasing CO/CO2 production ratios with increasing temperature. The CO2 was shown to react with carbon fibers following a Boudouard reaction at temperatures above 1200 K.

Francesco Panerai↗

NASA NTRS2023

Assessment of the Fluid Dynamics Boundary Condition in Ablating or Blowing Flows

Improved models of ablative thermal protection systems have enabled the treatment of materials and fluid behavior in a coupled manner. This paper reports a new approach to modeling the interface between fluid and material, with attention to the conservation of species mass flux and energy on the fluid side of the interface. The general equation is presented and is shown to recover the traditional uncoupled fluid/materials response interface. Including the chemical reaction terms on the CFD side of the interface makes the heat flux exchange independent of the thermodynamic reference state and, therefore, a measurable quantity. Doing so allows the material response solver to take as input the surface heat flux rather than a film coefficient. Removing the film coefficient approximation enables more direct solution of vehicle thermal response but requires consistency in the wall state. The mixing of the shock layer and pyrolysis gas is then computed with finite rate chemistry within the fluid solver. The boundary conditions described have been implemented in the DPLR v4.05.1 code. Char removal is captured using finite rate chemistry in DPLR’s gas surface interaction module. Aspects of coupling these solutions to material response are discussed.

Ablation↗