Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BUNDLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Nitride Fuel Potential for Power Uprates

This work presents the methodology and current results for design analysis of grid supported pressurized water reactor cores using uranium nitride (UN) fuel in square arrays. Uranium nitride has a higher theoretical density and higher thermal conductivity than uranium oxide, allowing for lower fuel temperatures, longer cycle length and higher power densities with similar enrichment. In order to avoid the UN and high temperature water reaction, silicon carbide cladding has been proposed in place of Zircaloy cladding. The analysis aims at finding the maximum thermal power over a range of bundle geometries (rod diameter and pitch). The same methodology is applied to the design of UO{sub 2} oxide fueled cores to provide a fair comparison of the achievable power rating between the two fuel types. Steady-state limits are considered, including fuel bundle pressure drop, minimum departure from nucleate boiling ratio (MDNBR), fuel temperature, fuel rod vibrations and pin fretting and sliding wear. Transients such as loss of flow and overpower accident will be considered. A steady state analysis was undertaken to determine the maximum achievable power that can be sustained by square array fuel assemblies loaded with nitride and oxide fuels with same or better safety performances as the reference design. Steady-state design limits were applied including MDNBR, fuel bundle pressure drop, fuel temperature, cumulative sliding and fretting wear. The major conclusions of this study are as follows: 1) It is possible to achieve significant power increase for UN and UO{sub 2} compared to the reference core power output of 3400 MWth with smaller but more numerous rods and higher pitch over diameter ratios. A power uprate of 25% can be reached according to the VIPRE-MATLAB interface for full core analysis with the same number of spacer grids, and 32% according to the new MATLAB script for single hot channel analysis, with five more spacer grids. For this latter core, a higher enrichment would be required. 2) The nitride fuel temperature constraint from dissociation doesn't influence steady state performances as other design constraints such as MDNBR and pressure loss are more restrictive. The oxide fuel temperature constraint from fission gas release is reached in part of the study domain, but not in the region that allows for possible uprates. 3) As a result, the thermal hydraulic performance of UN and UO{sub 2} are similar. Differences in possible power uprates will arise from fretting and sliding wear. Wear depends of the time spent by the fuel in the core, which depends on burnup and heavy metal inventory. UN being denser, it can allow for power uprates or increased cycle length. There is a trade off between power uprates and cycle length with regards to fuel pin wear. Reducing fuel pin wear by reducing cycle length can allow for higher thermal power. This affects the plants' economics as well. This work will be completed by a transient analysis using CASMO4E, SIMULATE3 and SIMULATE3k to model the neutronics of a nitride fueled core. The transient performances will be used to determine the maximum power uprates while performing as well or better during transients as the reference design. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Application of SPH Factors to PHWR Lattice Homogenization

Pressurized Heavy-Water Reactors (PHWRs) are heavy-water moderated and cooled. They consist of a horizontal, cylindrical, non-pressurized calandria vessel which contains the heavy-water moderator and is penetrated axially by fuel channels. Fuel channels consist of two concentric tubes separated by a gas gap: an inner tube called the pressure tube, and an outer tube called the calandria tube. The pressure tubes hold the fuel bundles, which are cooled by the flow of coolant at high temperature and pressure. The coolant flows in opposite directions in adjacent channels. The gap between the pressure and calandria tubes ensures that the temperature of the moderator remains relatively low, below 80 deg. C. For a CANDU 6 reactor, there are 380 fuel channels, each holding 12 37-element fuel bundles, approximately 10-cm in diameter and 50-cm long each. The fuel pins are arranged in three concentric rings (consisting of 6, 12 and 18 pins respectively), plus a central pin. The distance between channels (lattice pitch) is approximately 28.6 cm. Production core-level neutronics calculations are usually performed in a Cartesian geometry using few group diffusion and a simplified core model, whereby neutronics properties are homogenized over large regions called nodes. For Light Water reactors (LWRs), the two-dimensional axial (x-y) projection of a node corresponds to one fuel assembly. For PHWRs, a node usually consists of one fuel bundle and its associated moderator. For LWRs, advanced core-level calculations based on advanced node-level homogenization methods, such as Generalized Equivalence Theory (GET) or Super-homogenisation (SPH), improve the accuracy of full-core calculations compared to - standard homogenization. For rectangular fuel-pin arrangements, SPH can be used to perform pin-cell level homogenization which allows subsequent core-level diffusion calculations to be performed using fine Cartesian meshes. For PHWRs, the distribution of fuel pins in concentric rings makes the use of Cartesian mesh refinement impractical. However, SPH can still be applied, albeit using a coarser node subdivision, by dividing the heterogeneous node into 3x3 sub-regions in such a way that the central sub-region includes the entire fuel channel. This work investigates the use of SPH homogenization using a 3x3 subdivision of the PHWR node. Preliminary results show that the use of SPH factors does not yield more accurate results than standard homogenization when applied to PHWR nodes using a 3x3 subdivision. The explanation appears to lie in the fact that SPH factors are dependent on node-boundary leakage. Future investigations to confirm the leakage-dependence of SPH factors are recommended. Accuracy improvements may also be achievable by using smaller SPH regions at the periphery of the PHWR node, in an attempt to reduce the SPH factors' dependence on node-boundary leakage. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Simulation of Spent Nuclear Fuel loading into a Final Waste Repository

Previous work towards studying repository loading have used: - spent nuclear fuel (SNF) with an average burnup composition; - a lumped capacitance thermal model for calculating temperature in a Cyclus repository model. The goal of this work is to improve on the repository models and use U.S. historical SNF inventory data in simulations to more accurately study the loading of a waste repository. These goals will be achieved by: - using UNF-ST-and-DARDS Unified Database (UDB) that has historic assembly-specific data (e.g, isotopic composition, heat) in Cyclus simulations; - implementing a more accurate thermal model within a Cyclus repository model. Objectives: - Create a Cyclus spent fuel conditioning model that packages spent fuel bundles into packages which have user-defined properties. - Create a Cyclus medium-fidelity repository model that gives accurate time and spatial dependent temperature values and loads the repository based on a user-selected loading strategy. Cyclus is an agent-based extensible framework for modeling flow of material through user-defined nuclear fuel cycles. In Cyclus, each facility in the fuel cycle is modeled individually and the facilities interact with one another as independent agents. The spent fuel conditioning model accepts spent fuel bundles and puts them into a cylindrical waste package. In the spent fuel conditioning model, the user can define variables: For each layer, radius, thermal conductivity, thermal diffusivity; For each package, Number of spent fuel bundles, Radius and height. The waste repository model accepts waste packages and emplaces them into available positions within the waste repository based on a thermal criteria. The thermal criteria is a temperature limit at the interface between the waste package surface and the host geology, that is set based on the repository's host geology. In the waste repository model, the user can define the variables: Capacity, Distance between waste packages, Distance between drifts, Repository host geology, Loading Strategy. After the addition of new waste packages at each time step, the waste repository model recalculates the temperature at each location in the repository. If the addition of this new package causes its temperature to exceed the thermal limit, it will be placed back into the buffer. A thermal model that relies on a transient 'outside' model and quasi-steady-state 'inside' model is used to accurately determine the temperature in the repository. The 'outside' model assumes a homogenous medium with the Engineered Barrier System (EBS) replaced by the geologic medium. Temperature solutions for the central waste package, adjacent point and line sources are superimposed to calculate the temperature at specific points in the repository. The central drift consists of one finite line source which represents the central waste package. The central drift also consists of point sources that represent neighboring waste packages in the central drift. The neighboring drifts are represented by infinite line sources. The 'inside' model is considered to be at a quasi-steady-state condition because EBS has a relatively low thermal mass compared to the infinite geologic medium. The steady state calculation is performed at each time step with the heat source and interface temperature as boundary conditions. Future Work: Run Cyclus simulations with U.S. historical SNF inventory data, the spent fuel conditioning and repository models to study how waste package acceptance strategies impact repository loading.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Benchmark of Spacer Grid Models used in Nuclear Power Plants

The fuel bundles of both PWR and BWR reactors require spacers to maintain the integrity and spacing of the slender fuel rods. These spacers can provide benefits such as increased mixing and turbulence, which increases heat distribution, leading to better Departure from Nucleate Boiling (DNB) conditions in PWRs. They also enhance the critical power ratios by increasing the thickness of the liquid layer in BWRs. However, the spacers also cause a pressure drop which must be engineered into the performance and operation. The flow within a rod bundle involves a number of complicated factors, such as cross flow, (de)entrainment of liquid layer, bubble or droplet break up/join. This requires specialized 3 dimensional computational fluid dynamics for the complete flow, however, most of the newly developed models have been accomplished by industry, so they are proprietary and in addition require extensive programming and cost to implement. In the public domain, a number of 1 dimensional equations have been developed that could benefit in initial design and decision making, if the equations are valid in the new and different applications the models are used. In 2002, an OECD/NRC BFBT benchmark workshop determined the variables used in the development of models, to predict flow within nuclear fuel bundles, had not been updated with technological advances to replace general theory and characteristics. If those properties could be identified and modeled, they could be applied to a wider range of conditions. This study utilizes NUPEC BFBT tests' measured data, on an average spacer over a range of pressure and flows, which was determined to be the most detailed measured data available. The focus is to describe the mathematical models of spacer grids and validate them with experimental results. This study consists of compiling and comparing available and established single phase equations and models computations. While these models may not have the desired degree of accuracy for final decisions, they may be accurate enough for the initial phases of design. No conclusion on a universal equation that fits all boundary conditions accurately or detailed effect of properties was determined. However, by using the BFBT experimental data, boundary conditions where the spacer grid models can be useful were identified. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Triple Effect Economics: How Do Electric Vehicles, Solar Photovoltaics, and Work-from-Home Transform Household Electricity Cost?

Solutions for deep decarbonization need to be affordable as well as sustainable to garner widespread adoption. The past two decades have seen the introduction of new technologies and paradigms such as electric vehicles (EVs), solar photovoltaics (PVs), and increased work-from-home (WFH), which impact a household's overall energy consumption and cost in different ways. However, much attention has not been paid to explore the joint impact these technologies have on a household's electricity cost burden. Leveraging the 2020 Residential Energy Consumption Survey (RECS), this study presents an integrated model to unravel the extent to which the bundled adoption of EV-PV and stay-at-home decisions impact the total electricity cost of households. National level RECS data revealed that, compared to the baseline (i.e., households that did not own any of these technologies), households that own EVs, PVs, and engage in WFH observed a 13.5% decline in their electricity bills, despite a 25% increase in electricity consumption. The model results indicated that bundled adoption of EVs-PVs reduces electricity costs more significantly for a household, compared to the increased costs imposed by more household members staying at home. This holistic assessment presents an opportunity for decision makers to contextualize the changing energy costs and design effective strategies to foster a sustainable and cost saving mechanism. Policies such as bundled incentivization to motivate co-adoption, education about energy-management strategies, and add-on subsidies to adopt energy-efficient appliances, will not only accelerate decarbonization but increase household financial savings.

ADVANCED PROPULSION SYSTEMS,ENERGY PLANNING, POLIC↗

Computational Investigation of Fuel Dispersal Phenomena during Large-Break Loss of Coolant Accident in Light-Water Reactors

In the event of cladding rupture, which could occur in light water reactor fuel assemblies during a loss-of-coolant accident (LOCA), fuel particles, along with fission gases, can be expelled into the reactor core from the fractured fuel rod. This expulsion of fragmented fuel particles, referred as fuel dispersal, is the subject of investigation to evaluate the safety implications of increasing fuel burnup in light water reactors, with a specific focus on fuel fragmentation, relocation, and dispersal. Particle trajectories and the resulting mass distribution of the settled particles within the reactor pressure vessel can pose a long-term cooling challenge for the reactor core. The fuel dispersal phenomenon is significantly influenced by the ejection characteristics of the fuel fragments, as well as the size and shape of the cladding rupture and fuel rod depressurization history during LOCA transients. In this study, the transport of fuel particles within a scaled 5 × 5 lattice of a pressurized water reactor rod bundle geometry is modeled through a two-fluid Eulerian framework that treats the gas and solid phases as interpenetrating continua. The required boundary conditions are evaluated from the fuel performance code BISON in a postulated large-break LOCA scenario. The modeling framework considers solid fuel particles as granular matter, interacting with the gaseous dry steam phase and fission gases through the governing interfacial momentum and energy exchange between the gas and solid phases. The simulation results provide the volume fraction of the solids settled on the bottom surface of the fuel bundle, quantifying the deposition within the bundle geometry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Cytosolic proteins from tobacco pollen tubes that crosslink microtubules and actin filaments in vitro are metabolic enzymes

In plant cells, many processes require cooperative action of both microtubules and actin filaments, but proteins mediating interactions between these cytoskeletal members are mostly undiscovered. Here, we attempt to identify such proteins by affinity purification. Cytosol from Nicotiana tabacum (tobacco) pollen tubes was incubated first with actin filaments, and then proteins eluted from the actin were incubated with microtubules, and finally those microtubule-binding proteins were pooled in an active fraction. This fraction bundled actin filaments but not microtubules. However, when the fraction was added to both actin and microtubules, large bundles resulted, containing both polymers, regardless of the order of addition of components. Similar results were obtained when the order of affinity purification was reversed. The four most abundant bands from the fractions were identified from peptide fragments analyzed by mass spectrometry. The same four proteins were identified regardless of the order of affinity purification. The proteins are: homocysteine methyltransferase, phosphofructokinase, pyruvate decarboxylase, and glucan protein synthase (reversibly glycosylated protein). Furthermore, these results suggest the importance of structuring metabolism within the confines of the pollen tube cytoplasm.

actin-associated protein↗

Covalent inhibition of hAChE by organophosphates causes homodimer dissociation through long-range allosteric effects

Acetylcholinesterase (EC 3.1.1.7), a key acetylcholine-hydrolyzing enzyme in cholinergic neurotransmission, is present in a variety of states in situ, including monomers, C-terminally disulfide-linked homodimers, homotetramers, and up to three tetramers covalently attached to structural subunits. Could oligomerization that ensures high local concentrations of catalytic sites necessary for efficient neurotransmission be affected by environmental factors? Using small-angle X-ray scattering (SAXS) and cryo-EM, we demonstrate that homodimerization of recombinant monomeric human acetylcholinesterase (hAChE) in solution occurs through a C-terminal four-helix bundle at micromolar concentrations. We show that diethylphosphorylation of the active serine in the catalytic gorge or isopropylmethylphosphonylation by the R P enantiomer of sarin promotes a 10-fold increase in homodimer dissociation. We also demonstrate the dissociation of organophosphate (OP)-conjugated dimers is reversed by structurally diverse oximes 2PAM, HI6, or RS194B, as demonstrated by SAXS of diethylphosphoryl-hAChE. However, binding of oximes to the native ligand-free hAChE, binding of high-affinity reversible ligands, or formation of an S P -sarin-hAChE conjugate had no effect on homodimerization. Dissociation monitored by time-resolved SAXS occurs in milliseconds, consistent with rates of hAChE covalent inhibition. OP-induced dissociation was not observed in the SAXS profiles of the double-mutant Y337A/F338A, where the active center gorge volume is larger than in wildtype hAChE. These observations suggest a key role of the tightly packed acyl pocket in allosterically triggered OP-induced dimer dissociation, with the potential for local reduction of acetylcholine-hydrolytic power in situ. Computational models predict allosteric correlated motions extending from the acyl pocket toward the four-helix bundle dimerization interface 25 Å away.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A strong nonequilibrium bound for sorting of cross-linkers on growing biopolymers

Significance Understanding the connection between microscopic driving forces in biological systems and their emergent structures remains an outstanding challenge. We tackle this problem by deriving a fluctuation–response bound in the context of actin polymerization and bundling and verify its robustness far from equilibrium through simulation. Our results show how actin polymerization, molecular fluxes of cross-linker binding, and the morphology of the growing bundle are associated quantitatively; when the bound is saturated, it becomes a nonequilibrium linear-response relation. Molecular driving forces are difficult to measure directly in biological systems, and this work represents a first step toward estimating them from experimentally accessible quantities such as molecular fluxes and compositions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Counting topological interface modes using simplicial characteristic classes

A computational approach for predicting the number of topological interface modes (TIMs) in hermitian systems using the spectral flow—monopole correspondence is presented. The number of TIMs is determined by calculating the Chern number of a complex line bundle of local polarisation vectors over a phase space sphere surrounding a Weyl point. The Chern number is computed by constructing the simplicial first Chern class of a discrete vector bundle on a simplicial mesh. This approach is gauge invariant, derivative free, structure preserving, and robust to noise. The algorithm is shown to reproduce the expected number of TIMs for the case of equatorial fluid waves and the topological Langmuir cyclotron wave. The possibility of using this algorithm to analyse experimental measurements of bulk wave polarisations and predict the associated number of TIMs is explored in a synthetic example.

discrete vector bundles↗

Progress on the Development of a Step Height Sensor for the BOLT Flight Vehicle

This presentation will summarize progress on the development of a step height sensor for the BOLT flight vehicle. Two methods have been proposed to measure the step size in this effort.The first method involves the application of miniaturized camera embedded in the flight vehicle that views the step through a rearward-facing port (shown in Fig. 1a inset). The second method involves the application of a linear fiber optic array bundle to measure the intensity of light reflected back from the aft body step (concept shown in Fig. 1b). Preliminary testing with the miniaturized camera has been performed in the lab and shows that displacements of ≤10 μm can be measured using this method. Final testing with both methods will be performed on the test stand shown in Fig. 1a. This test stand will include a fine adjustment vertical translation stage that will be used to adjust the step height in steps of 1-2 μm. A high-magnification imaging system will also be used to verify the step height. The miniaturized camera and linear fiber optic array bundle will be mounted in one of several port holes with varying degrees of inclination relative to the top surface in the opposing aft-section slab. BOLT flight vehicle details and information on the steps can be found in Ref. [1].

BOLT↗

Hierarchical Self‐Assembly of Multidimensional Functional Materials from Sequence‐Defined Peptoids

Abstract Hierarchical self‐assembly represents a powerful strategy for the fabrication of functional materials across various length scales. However, achieving precise formation of functional hierarchical assemblies remains a significant challenge and requires a profound understanding of molecular assembly interactions. In this study, we present a molecular‐level understanding of the hierarchical assembly of sequence‐defined peptoids into multidimensional functional materials, including twisted nanotube bundles serving as a highly efficient artificial light harvesting system. By employing synchrotron‐based powder X‐ray diffraction and analyzing single crystal structures of model compounds, we elucidated the molecular packing and mechanisms underlying the assembly of peptoids into multidimensional nanostructures. Our findings demonstrate that incorporating aromatic functional groups, such as tetraphenyl ethylene (TPE), at the termini of assembling peptoid sequences promotes the formation of twisted bundles of nanotubes and nanosheets, thus enabling the creation of a highly efficient artificial light harvesting system. This research exemplifies the potential of leveraging sequence‐defined synthetic polymers to translate microscopic molecular structures into macroscopic assemblies. It holds promise for the development of functional materials with precisely controlled hierarchical structures and designed functions.

Shao, Li↗

Electrostatic Control of Bioactivity

The power of independence: When exhibited on the surface of self-assembling peptide-amphiphile nanofibers, the hydrophobic laminin-derived IKVAV epitope induced nanofiber bundling through interdigitation with neighboring fibers and thus decreased the bioactivity of the resulting materials. The inclusion of charged amino acids in the peptide amphiphiles disrupted the tendency to bundle and led to significantly enhanced neurite outgrowth.

59 BASIC BIOLOGICAL SCIENCES↗

Hierarchical Self‐Assembly of Multidimensional Functional Materials from Sequence‐Defined Peptoids

Abstract Hierarchical self‐assembly represents a powerful strategy for the fabrication of functional materials across various length scales. However, achieving precise formation of functional hierarchical assemblies remains a significant challenge and requires a profound understanding of molecular assembly interactions. In this study, we present a molecular‐level understanding of the hierarchical assembly of sequence‐defined peptoids into multidimensional functional materials, including twisted nanotube bundles serving as a highly efficient artificial light harvesting system. By employing synchrotron‐based powder X‐ray diffraction and analyzing single crystal structures of model compounds, we elucidated the molecular packing and mechanisms underlying the assembly of peptoids into multidimensional nanostructures. Our findings demonstrate that incorporating aromatic functional groups, such as tetraphenyl ethylene (TPE), at the termini of assembling peptoid sequences promotes the formation of twisted bundles of nanotubes and nanosheets, thus enabling the creation of a highly efficient artificial light harvesting system. This research exemplifies the potential of leveraging sequence‐defined synthetic polymers to translate microscopic molecular structures into macroscopic assemblies. It holds promise for the development of functional materials with precisely controlled hierarchical structures and designed functions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The crystal structure of the mycobacterium tuberculosis Rv3019c-Rv3020c ESX complex reveals a domain-swapped heterotetramer

Mycobacterium tuberculosis encodes five gene clusters (ESX-1 to ESX-5) for Type VII protein secretion systems that are implicated in mycobacterial pathogenicity. Substrates for the secretion apparatus are encoded within the gene clusters and in additional loci that lack the components of the secretion apparatus. The best characterized substrates are the ESX complexes, 1:1 heterodimers of ESAT-6 and CFP-10, the prototypical member that has been shown to be essential for Mycobacterium tuberculosis pathogenesis. We have determined the structure of EsxRS, a homolog of EsxGH of the ESX-3 gene cluster, at 1.91 {angstrom} resolution. The EsxRS structure is composed of two four-helix bundles resulting from the 3D domain swapping of the C-terminal domain of EsxS, the CFP-10 homolog. The four-helix bundles at the extremities of the complex have a similar architecture to the structure of ESAT-6 {center_dot} CFP-10 (EsxAB) of ESX-1, but in EsxRS a hinge loop linking the {alpha}-helical domains of EsxS undergoes a loop-to-helix transition that creates the domain swapped EsxRS tetramer. Based on the atomic structure of EsxRS and existing biochemical data on ESX complexes, we propose that higher order ESX oligomers may increase avidity of ESX binding to host receptor molecules or, alternatively, the conformational change that creates the domain swapped structure may be the basis of ESX complex dissociation that would free ESAT-6 to exert a cytotoxic effect.

36 MATERIALS SCIENCE↗

An autonomous robot for shell and tube heat exchanger inspection

Shell and tube heat exchangers (STHEs) are critical to energy conversion efficiency of power plants. Eddy current examination is a way to evaluate working conditions of these tubes. However, the current testing apparatus requires human to manually insert an eddy current testing (ECT) probe into and extract it out of individual tubes, and meanwhile monitor measurement results for diagnosis. It is a time-consuming and labor-intensive procedure even for an experienced technician. To tackle this challenge, in this study, we developed a robot enabled ECT system for autonomous inspection of STHEs. The robotic platform employs Mecanum wheeled chassis for high mobility, machine vision to locate tube bundle and tube inlets, a rotational Cartesian mechanism to operate at planes with all possible inclinations, and a task-specific mechanism for ECT probe delivery. Machine vision locates tube bundle and tube inlets by an April tag detection algorithm and a Circle Hough Transform algorithm, respectively. Assisted by a guiding cone, the ECT probe is continuously fed into the tubes with a fill factor of 0.819. In conclusion, during this process, the eddy current data are automatically collected and real-time analyzed by convolutional neural networks, showing accuracy of nearly 100% for identifying defective and nondefective tubes and 85% for four types of defective tubes and nondefective tubes.

42 ENGINEERING↗

Machine learning and algebraic approaches towards complete matter spectra in 4d F-theory

Motivated by engineering vector-like (Higgs) pairs in the spectrum of 4d F-theory compactifications, we combine machine learning and algebraic geometry techniques to analyze line bundle cohomologies on families of holomorphic curves. To quantify jumps of these cohomologies, we first generate 1.8 million pairs of line bundles and curves embedded in dP 3 , for which we compute the cohomologies. A white-box machine learning approach trained on this data provides intuition for jumps due to curve splittings, which we use to construct additional vector-like Higgs-pairs in an F-Theory toy model. We also find that, in order to explain quantitatively the full dataset, further tools from algebraic geometry, in particular Brill-Noether theory, are required. Using these ingredients, we introduce a diagrammatic way to express cohomology jumps across the parameter space of each family of matter curves, which reflects a stratification of the F-theory complex structure moduli space in terms of the vector-like spectrum. Furthermore, these insights provide an algorithmically efficient way to estimate the possible cohomology dimensions across the entire parameter space.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗