Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

SU-F-T-361: Dose Enhancement Due to Nanoparticle Addition in Skin Radiotherapy: A Monte Carlo Study Using Kilovoltage Photon Beams

Purpose: This study investigated the dose enhancement due to addition of nanoparticles with different types and concentrations in skin radiotherapy using kilovoltage photon beams. Methods: An inhomogeneous water phantom (15×15×10 cm{sup 3}) having the skin target layer (0.5–5 mm), added with different concentrations (3–40 mg/ml) of nanoparticles (Au, Pt, I, Ag and Fe{sub 2}O{sub 3}), was irradiated by the 105 and 220 kVp photon beams produced by a Gulmay D3225 Orthovoltage unit. The circular cone of 5-cm diameter and source-to-surface distance of 20 cm were used. Doses in the skin target layer with and without adding the nanoparticles were calculated using Monte Carlo simulation (the EGSnrc code) through the macroscopic approach. Dose enhancement ratio (DER), defined as the ratio of dose at the target with nanoparticle addition to the dose without addition, was calculated for each type and concentration of nanoparticle in different target thickness. Results: For Au nanoparticle, DER dependence on target thickness for the 220 kVp photon beams was not significant. However, DER for Au nanoparticle was found decreasing with an increase of target thickness when the nanoparticle concentration was increased from 18 to 40 mg/ml using the 105 kVp photon beams. For nanoparticle concentration of 40 mg/ml, DER variation with target thickness was not significant for the 220 kVp photon beams, but DEF was found decreasing with the target thickness when lower energy of photon beam (105 kVp) was used. DEF was found increasing with an increase of nanoparticle concentration. The higher the DEF increasing rate, the higher the atomic number of the nanoparticle except I and Ag for the same target thickness. Conclusion: It is concluded that nanoparticle addition can result in dose enhancement in kilovoltage skin radiotherapy. Moreover, the DER is related to the photon beam energy, target thickness, atomic number and concentration of nanoparticles.

60 APPLIED LIFE SCIENCES↗

Performance Improvement of Lithium Metal Batteries Enabled By LiBF 3 CN as a New Electrolyte Additive

A newly synthesized electrolyte additive, lithium trifluoro(cyano) borate (LiBF 3 CN), has been investigated for electrochemical performance improvement of lithium metal batteries. The LiBF 3 CN has a structure where one fluorine atom of BF 4 – is substituted with a cyano group (–CN) prepared by the reaction of boron trifluoride etherate with lithium cyanide. The electrochemical performance in symmetric Li/Li cells and NCM523/Li cells is significantly improved upon the incorporation of LiBF 3 CN as an electrolyte additive into a carbonate-based electrolyte. Extensive characterization of the deposited lithium metal reveals that a thin (≈20 nm) and robust SEI composed of LiN x O y , Li 3 N and Li 2 O is formed by the reductive decomposition of the LiBF 3 CN additive, which plays an important role in decreasing the resistance and stabilizing lithium deposition/stripping. The insight into the substitution effect of a functional group obtained from this work provides guidance for the design of new electrolyte additives.

25 ENERGY STORAGE↗

Impact of Electrolyte Additives on the Lifetime of High Voltage NMC Lithium-Ion Pouch Cells

This work involves improving the lifetime of lithium-ion cells during high voltage cycling using electrolyte additives. Three generations of electrolyte additives were investigated and screened in NMC442/graphite pouch cells using a 24 h voltage-hold protocol at 40 degrees C to accelerate oxidative reactions occurring at 4.4 V. Once promising additives and combinations were identified, they were then tested in cobalt-free NMC640/graphite cells for long-term cycling to upper cutoff voltages of 4.3, 4.4, and 4.5 V at temperatures of 20, 40, and 55 degrees C. Degradation mechanisms were probed using dV/dQ analysis, micro-X-ray fluorescence spectroscopy, and electrochemical impedance spectroscopy. The primary failure mode of cells held at high voltages is due to increase in cell impedance, which is correlated to the dissolution of transition metals, specifically manganese, originating from the positive electrode. We believe this dissolution is presumably due to the formation of a high impedance rock salt surface layer on the NMC positive electrode particles. Such deleterious outcomes can be limited by selecting an appropriate electrolyte additive package. It is hoped that this paper can provide a starting point for developing NMC Li-ion cells that can operate to voltages as high as 4.4 V and still display long lifetimes.

Azam, Saad↗

The Role of Additives in Improving Performance in High Voltage Lithium-Ion Batteries with Potentiostatic Holds

In this work, various electrolyte additives designed for enhanced performance at high voltages were evaluated with elevated temperature potentiostatic holds with LiNi0.5Co0.2Mn0.3/Li4Ti5O12 full cells to determine their effect on the high voltage stability. Of the additives investigated, many showed increased oxidation current through the 60 hour potentiostatic holds test, and adversely affected both the capacity retention and interfacial impedance. Improved high voltage performance was observed with two additives, vinylene carbonate (VC) and 1,1,2,2- tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether (TTE), which was attributed to two different mechanisms of improvement. This work challenges some conclusions in the available literature that an additive molecule that decomposes on the charged cathode surface and passivates the surface against electrolyte oxidation.

Tornheim, Adam↗

Lipophilic Additives for Highly Concentrated Electrolytes in Lithium-Sulfur Batteries

The use of concentrated electrolytes in batteries has been impeded in part by the lack of compatible electrolyte additives for protection of electrodes. Herein, a lipophilic additive tetrabutylammonium iodide (TBAI = [Bu4N]I) was introduced to concentrated electrolyte (CH3CN)(2)LiTFSI/TTE (TTE = 1,1,2,2-tetrafluoroethyl 2,2,3,3-tetrafluoropropyl ether) for Li-S batteries. Electrochemical and SEM/EDS analyses showed that the additive provided short-term capacity retention via removal of S deposits by in situ generated I-2. These results strongly suggest lipophilic salts as viable candidates for additives in concentrated electrolytes. (c) 2019 The Electrochemical Society.

Lau, Ka-Cheong↗

Application of Linear Additive Conditions for Near-Infrared Diffuse Reflectance Absorption Spectroscopy

Determining the homogeneity of material mixing in real time during product processing is critical for quality control. According to the Kubelka–Munk (K-M) function of diffuse reflectance absorption spectrum, absorbance (A) is approximately linear with the content of the components when the sample scattering coefficient (S) is in a certain range. The S is determined by the particle size of powder samples. Therefore, this study determined particle size ranges that satisfy linear additivity in near-infrared diffuse reflectance spectroscopy (NIRDRS). Thus, the proposed NIRDRS analysis technique can be used to determine the homogeneity of material mixes or analyze the percentages of the components in the mixture. In this study, vitamin B3 and vitamin C were used for preparing mixed samples with varying percentages. The experimental results revealed that linear additivity is satisfied when the powder particle size is in the range of less than 280, 280–450, and 450–900 μm. When the confidence level is 0.01, the actual mixed spectra are not significantly different from the “simulated mixed spectra” constructed by linear addition, with their relative deviations less than 1.08%. The absolute errors of the actual and analytic percentages were within 2.98% for each component in the mixtures. The above conclusions also hold for sorghum, which has a complex material composition. Statistical models cannot analyze the percentages of components in the mixture. In contrast, linear addition and direct calibration approach avoids the use of a large number of samples for statistical modeling and analyze the percentages of mixed samples. Meanwhile, it can be used to discriminate and analyze the material mixing uniformity by building a mechanistic model.

Feng, Zhiyue↗

ODI notebook additive_manufacturing_video_2022

Additive Manufacturing, video dataset Two-photon lithography (TPL) is a widely used 3D nanoprinting technique that uses laser light to create objects. Challenges to large-scale adoption of this additive manufacturing method include identifying light dosage parameters and monitoring during fabrication. A research team from LLNL, Iowa State University, and Georgia Tech is applying machine learning models to tackle these challenges-i.e., accelerate the process of identifying optimal light dosage parameters and automate the detection of part quality. Funded by LLNL's Laboratory Directed Research and Development Program, the project team has curated a video dataset of TPL processes for parameters such as light dosages, photo-curable resins, and structures. Both raw and labeled versions of the datasets are available on the links in the Open Data Initiative page. The code uses the labeled dataset. Notebook compiled by Nisha Mulakken (mulakken1@llnl.gov) for LLNL Open Data Initiative, Summer 2022. Original code provided by research team. Publications: X.Y. Lee, S.K. Saha, S. Sarkar, B. Giera. "Automated detection of part quality during two-photon lithography via deep learning." Additive Manufacturing 36, December 2020: doi.org/10.1016/j.addma.2020.101444 X.Y. Lee, S.K. Saha, S. Sarkar, B. Giera. "wo Photon lithography additive manufacturing: Video dataset of parameter sweep of light dosages, photo-curable resins, and structures." Data in Brief 32, October 2020. doi.org/10.1016/j.dib.2020.106119.

Mulakken, NishaJ↗

PyTorch Implementation of Log-Additive Convolutional Neural Networks

This code is a collection of python code that defines, trains, and tests Log-Additive Convolutional Neural Networks. The model components and training routine are based on the PyTorch python library. The code implements the Log-Additive Convolutional Neural Networks as described in Pagendam et al. 2023. In addition to the Log-Additive Convolutional Neural Networks, this library also defines the Log-Normal Density loss function as described in Pagendam et al. 2023. Code from this paper is not publicly available, so the Pytorch implementation of this type of model is unique to this library.

Callis, Skylar↗

Development and evaluation of a skeletal mechanism for EHN additized gasoline mixtures in large Eddy simulations of HCCI combustion

Advanced Low Temperature Combustion modes, such as the Sandia proposed Additive-Mixing Fuel Injection (AMFI), can unlock significant potential to boost fuel conversion efficiency and ultimately improve the energy conversion of internal combustion engines. This is a novel improved combustion process that is enabled by supplying small (<5%) variable amounts of autoignition improver to the fuel to enhance the engine operation and control. Common, diesel-fuel ignition-quality enhancing additive, 2-ethylexyl nitrate (EHN), is doped into gasoline to enable Sandia LTGC + AMFI combustion. This manuscript focuses on the development of a reduced sub-mechanism for EHN chemical kinetics at engine relevant conditions that is implemented into a skeletal mechanism for chemical kinetic studies of gasoline surrogate fuels. The mechanism validation utilized zero-dimensional numerical simulations and comparison to shock tube ignition-delay data of pure and EHN-doped n-heptane. Additional validation is presented with Homogeneous Charge Compression-Ignition (HCCI) engine data of pure and EHN-doped research-grade E10 gasoline. Then, the mechanism was deployed in a 3-D computational fluid dynamics (CFD) using Large Eddy Simulations (LES) to model the HCCI engine experiments of 0.4% vol EHN additized E10 gasoline at several equivalence ratios. Simulations showed a very good performance of the mechanism, and the model accurately reproduced (a) the ignition point, (b) combustion phasing, (c) combustion duration, and (d) the peak of the heat release rates of the engine experiments. The results show that EHN promotes Low-Temperature Heat Release, ultimately driving the gasoline to autoignite at thermodynamic conditions where the fuel would not otherwise ignite. Overall, this work demonstrates a viable reduced chemical-kinetic mechanism for EHN and shows that it can be combined with a skeletal gasoline mechanism for CFD-LES analysis of well-mixed LTGC that matches well with experimental results. The CFD-LES analysis also shows the spatial distribution of EHN-fuel interactions that control the autoignition throughout the combustion chamber.

Guleria, Gaurav↗

In situ Visible Light and Thermal Imaging Data from a Laser Powder Bed Fusion Additive Manufacturing Process Co-Registered to X-ray Computed Tomography and Fatigue Data

This dataset is comprised of in situ sensing data collected during a laser-based powder bed fusion additive manufacturing process, as well as rasterized scan path information, post-build X-ray computed tomography (XCT), and fatigue test results. A total of 64 cylinders, approximately 15 mm in diameter and 102 mm tall, were printed out of stainless steel 316H on a Colibrium Additive Concept Laser M2 Series 5 machine. Parameters known to produce dense material were used to construct 56 of these cylinders, while the remaining 8 cylinders were printed with relatively high energy density parameters prone to producing keyhole pores. In addition, two spatter generation blocks were constructed upstream of the 64 cylinders such that ejecta produced during the melting of the spatter generators were stochastically seeded onto the 64 cylinders. Based on previous experiments, these spatter particles were theorized to produce stochastic lack-of-fusion pores. During the construction of the build, high-resolution images of reflected light in the visible spectrum were captured both before and after recoating for each print layer. Additionally, temporally integrated thermal imaging in the near infrared spectrum produced integrated sum and max images on a layerwise basis. The multimodal in situ data has been co-registered to the build plate coordinate system, allowing for identification of process anomalies (e.g., spatter particles) apparent in the two sensors. Following construction of the build, the cylinders were subjected to XCT to identify internal flaws, and the resulting data have also been registered to the build plate coordinate system. Finally, 60 of the 64 cylinders were machined into fatigue coupons conforming to ASTM E466 and subsequently subjected to either high- or -low-cycle fatigue testing. The results of the fatigue tests have also been included in the dataset, and the XCT data corresponded to the approximate location of the gauge sections of the machine fatigue specimen geometry.

42 ENGINEERING↗

Effect of additives on carbon dioxide uptake and compressive strength of dry-cast concrete

The main thrust of the work reported herein is to study the effect of chemical additives to make beneficial use of carbon dioxide in enhancing the compressive strength of dry-cast concrete. The additives used in this investigation were calcium and magnesium oxides and silicates, nickel oxide, sodium hydroxide, sodium bicarbonate and strontium chloride. The experimental results showed that both the carbonation reactions and the compressive strength of dry-cast concrete mixtures were improved when using chemical additives. Experimental investigations for optimisation were also undertaken with selected additives to further increase the carbon dioxide uptake and improve the compressive strength. The best results were obtained when using calcium silicate in combination with calcium oxide. The early-age compressive strength of specimens made from the optimised mixture increased from 9·82 MPa to 13·32 MPa, and the specimens’ carbon dioxide uptake increased from 8·76% to 10·62% of cement weight.

Construction & Building Technology↗

Ionic Liquids as Multi-Functional Lubricant Additives to Enhance Engine Efficiency (final report NFE-12-03876)

This ORNL-Shell CRADA developed and investigated ionic liquids (ILs) as multifunctional additives for next-generation low-viscosity engine oils. Several groups of oil-miscible ILs were successfully designed and synthesized with high thermal stability, non-corrosiveness, excellent wettability, and most importantly effective anti-scuffing/anti-wear and friction reduction characteristics. Synergistic effects between the common anti-wear additive zinc dialkyldithiophosphate (ZDDP) and a particular group of ILs were discovered with > 30% friction reduction and 70% wear reduction compared with using ZDDP or IL alone. The IL+ZDDP tribofilm distinguishes itself from the IL or ZDDP tribofilms with substantially higher contents of metal phosphates but less metal oxides and sulfur compounds. Notably, it was revealed that the actual concentrations of functional elements on the droplet surface of the oil containing IL+ZDDP are one order magnitude higher than their nominal values. Such significantly increased concentrations of anti-wear agents are presumably expected for the oilsolid interface and believed to be responsible for the superior lubricating performance. A prototype SAE 0W-16 engine oil using a synergistic IL+ZDDP pair as the anti-wear additive has been formulated based on the compatibility between the IL and other additives. Sequence VIE full-scale engine dynamometer tests demonstrated fuel economy improvement (FEI) for this prototype oil and revealed the individual contributions from the lower oil viscosity and reduced boundary friction. The impact of IL and IL+ZDDP on exhaust emission catalyst was investigated using an accelerated small engine aging test and results were benchmarked against ZDDP.

33 ADVANCED PROPULSION SYSTEMS↗

Assessment of Gasoline Additive Containing Ditert-butoxypropanol

The Fuels, Engines, and Emissions Research Center completed analysis and testing of the CPS Powershot gasoline additive under the auspices of the Department of Energy’s Technical Assistance for US Small Businesses in Vehicle Technologies. Gas chromatography-mass spectrometry (GC-MS) was used to quantify the makeup of the additive, finding a predominance of 2,3-Ditert-Butoxypropanol, also known as Glyceryl Di-Tert-Butyl Ether (GTBE). Blends of the additive at 2 and 4 volume percent were subjected to a number of standard ASTM tests, including Research Octane Number, Motor Octane Number, distillation, and vapor pressure. Results show a high boiling range and low vapor pressure for the additive, and a very modest octane boosting effect in gasoline with and without ethanol.

54 ENVIRONMENTAL SCIENCES↗

CRADA/NFE-15-05761 Report: Additive Manufacturing of Isotropic NdFeB Bonded Permanent Magnets

The technical objective of this technical collaboration phase I proposal is to fabricate net shape isotropic NdFeB bonded magnets utilizing additive manufacturing technologies at the ORNL MDF. The goal is to form complex shapes of thermoplastic and/or thermoset bonded magnets without expensive tooling and with minimal wasted material. Two additive manufacturing methods; the binder jet process; and big area additive manufacturing (BAAM) were used. Binder jetting produced magnets with the measured density of the magnet of 3.47 g/cm 3 , close to 46% relative to the NdFeB single crystal density of 7.6 g/cm 3 were demonstrated. Magnetic measurements indicate that there is no degradation in the magnetic properties. In addition, BAAM was used to fabricate isotropic near-net-shape NdFeB bonded magnets with magnetic and mechanical properties comparable or better than those of traditional injection molded magnets. The starting polymer magnet composite pellets consist of 65 vol% isotropic NdFeB powder and 35 vol% polyamide (Nylon-12). The density of the final BAAM magnet product reached 4.8 g/cm 3 , and the room temperature magnetic properties are: Intrinsic coercivity Hci = 8.65 kOe, Remanence Br = 5.07 kG, and energy product (BH) max = 5.47 MGOe (43.50 kJ/m 3 ). This study provides a new pathway for preparing near-net shape bonded magnets for various magnetic applications.

36 MATERIALS SCIENCE↗

Bio-reinforced composite development for additive manufacturing: Nanocellulose-PLA

Additive manufacturing (AM) is transitioning from being only a prototyping method towards becoming a manufacturing technique for the quick production of parts with complex geometries. For the complete realization of this transition, the mechanical properties of the printed parts have to meet the requirements of actual load-bearing structural components. Integration of a reinforcing second phase into a polymer is a viable approach for the improvement of resins mechanical performance. Addition of carbon fibers into acrylonitrile-butadiene-styrene (ABS) has already been shown to improve its mechanical properties compared to the neat ABS resin (both additively manufactured), and led to the manufacture of world s first 3D-printed car. However, both ABS resin and carbon fibers are petroleum-based products, and there is a continuous search for alternative, bio-sourced, renewable materials as a feedstock for manufacturing. Towards this direction, we have investigated the potential of cellulose nanofibril-reinforced polylactic acid (PLA) resin systems as an alternative. CNF-PLA composite systems with up to 40 wt% CNF loadings were prepared via compression molding technique and tested. Significant improvements in both tensile strength (80%) and elastic modulus (128%) were observed. Filaments prepared from the same compositions were also successfully 3D-printed into tensile testing specimens with up to 30% CNF concentrations, and showed similar improvements in mechanical performance. Although CNFs were not individually dispersed in PLA matrix, they were observed to be well blended with the polymer based on SEM micrographs. In summary, preparation and 3D-printing of a 100% bio-based feedstock material with the mechanical properties comparable to the carbon fiber-ABS system was successfully demonstrated that it can open up new window of opportunities in the additive manufacturing industry. Acknowledgement Research sponsored by the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, under contract DE-AC05-00OR22725 with UT-Battelle, LLC.

09 BIOMASS FUELS↗

Wire Arc Additive Manufacturing

Project highlight. This project designs and implements a new additive manufacturing capability at Savannah River National Laboratory. Wire Arc Additive Manufacturing is an Advanced Manufacturing technology that enables materials and energy savings by producing materials that are in near net shapes to minimize material losses compared to conventional forging and machining techniques. Wire arc additive manufacturing is an evolving technology that can be used to fabricate large components with significantly less materials waste than conventional processing. This project includes an engineering model, an aspect that is largely overlooked in the Additive Manufacturing modeling work where the emphasis has been on mechanistic and microscopic modeling, to estimate the residual stresses and distortions. The Abaqus Weld Interface software coupled with user subroutines in Fortran enable the local cooling rates to be estimated to provide a coarse scale model for the secondary dendrite arm spacing, a parameter useful to estimate mechanical properties.

36 MATERIALS SCIENCE↗

Utility of Big Area Additive Manufacturing for Part Production for Low-Head Hydropower (CRADA NFE-18-07280 Final Report)

ORNL worked with Cadens, LLC, to explore the use of additive manufacturing (AM) to produce low-cost parts for low-head hydropower systems. Cadens develops design optimization software that leverages the flexible, low-cost, high-strength benefits of AM and composite materials. Cadens also operates a micro-hydro lab to test AM components in controlled environments. Until now, Cadens’ tests have been limited to components of a size that they can cost-effectively manufacture using local commercial systems. This project provided an opportunity for Cadens to scale up their modular AM hydropower parts using the capabilities of Big Area Additive Manufacturing (BAAM). This project was a success and resulted in the design and fabrication of several end-use parts of a hydropower system, using a Big Area Additive Manufacturing (BAAM) system. The fabricated parts include a draft tube, thimble, runner housing mold, PVC end fitting and two PVC pipe supports. In addition, a runner system was fabricated using fused deposition modeling on a 3D Platform Workbench 400 Series System.

13 HYDRO ENERGY↗

Feedstock Modification for Enhanced Additive Alloys

This project investigated the use of Y 2 O 3 nanoparticles to enhance IN625 feedstock for metal additive manufacturing. The oxide nanoparticles are adhered to the outer surface of the pre-alloyed IN625 powder feedstock, and serve to form an oxide dispersion strengthened (ODS) material in situ during processing. The conventional and enhanced feedstocks were processed using a laser powder bed fusion additive manufacturing (AM) system. The properties of the AM materials were characterized at elevated temperatures and compared to conventional wrought material. The addition of the Y 2 O 3 nanoparticles improved the yield strength, stress rupture, and corrosion properties of the AM material, and compared more favorably with conventional wrought IN625. This research will enable future adoption of additively manufactured ODS-IN625 components with superior properties to current printed IN625 material.

36 MATERIALS SCIENCE↗