Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACTIVATION ENERGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Microstructure and deformation behavior of nickel based superalloy Inconel 740 prepared by electron beam smelting

Electron beam smelting (EBS) has been used to fabricate the Inconel 740 superalloy. Microstructures, hardness, and deformation characteristics of the alloy are studied. It is observed that carbides and fine secondary phase nuclei are distributed in the hot worked EBS 740 superalloy. The Ostwald ripening occurs during solution treatment and leads to aggregation of the γ′ precipitates, the size of γ′ precipitates varies from several nanometers to more than one hundred nanometers as a result. The average size of the secondary phase is < 30 nm after aging treatment and the average Vickers hardness is measured to be about 370. The critical shear stress is calculated to be 0.627 GPa with governing mechanism of shearing, causing a stronger strengthening effect than the traditionally prepared Inconel 740 superalloy. The compression behavior indicates that the EBS 740 superalloy shows higher flow stress than 740H at low Zener-Hollomon parameter, which may arise from the undissolved γ′ precipitates and higher activation energy Q. The tensile results show that the fracture surface exhibits a ductile fracture pattern, in contrast to no obvious plastic deformation on the macroscopic fracture. Crack propagation proceeds in a transgranular fracture mode with facets and voids presented on the fracture surface. - Graphical abstract: Electron beam smelting (EBS) has been used to fabricate the Inconel 740 superalloy. Microstructures, hardness, and deformation characteristics of the alloy are studied. The average size of the secondary phase is < 30 nm after aging treatment and the average Vickers hardness is measured to be about 370. The critical shear stress is calculated to be 0.627 GPa with governing mechanism of shearing, causing a stronger strengthening effect than the traditionally prepared Inconel 740 superalloy. The EBS 740 superalloy shows higher flow stress than 740H at low Zener-Hollomon parameter, which may arise from the undissolved γ′ precipitates and higher activation energy Q. The EBS technology shows encouraging potential in preparation of nickel-based superalloys. Morphologies of γ′ precipitates and Vickers hardness as well as hot compression curves for electron beam smelting 740 superalloy. - Highlights: • Electron beam smelting, a novel method, was used to prepare the Inconel 740 superalloy. • The average size of the γ′ precipitates after aging treatment is < 30 nm. • The shearing mode generates a stronger strengthening effect than the traditional 740. • At low Zener-Hollomon parameter, the EBS 740 shows higher flow stress than 740H.

36 MATERIALS SCIENCE↗

The origin of the conductivity maximum in molten salts. II. SnCl{sub 2} and HgBr{sub 2}

The phenomenon of electrical conductivity maxima of molten salts versus temperature during orthobaric (closed-vessel) conditions is further examined via ab initio simulations. Previously, in a study of molten BiCl{sub 3}, a new theory was offered in which the conductivity falloff at high temperatures is due not to traditional ion association, but to a rise in the activation energy for atomic ions hopping from counterion to counterion. Here this theory is further tested on two more inorganic melts which exhibit conductivity maxima: another high-conducting melt (SnCl{sub 2}, σ{sub max} = 2.81 Ω{sup −1} cm{sup −1}) and a low-conducting one (HgBr{sub 2}, σ{sub max} = 4.06 × 10{sup −4} Ω{sup −1} cm{sup −1}). First, ab initio molecular dynamics simulations were performed and again appear successful in reproducing the maxima for both these liquids. Second, analysis of the simulated liquid structure (radial distributions, species concentrations) was performed. In the HgBr{sub 2} case, a very molecular liquid like water, a clear Grotthuss chain of bromide transfers was observed in simulation when seeding the system with a HgBr{sup +} cation and HgBr{sub 3}{sup −} anion. The first conclusion is that the hopping mechanism offered for molten BiCl{sub 3} is simply the Grotthuss mechanism for conduction, applicable not just to H{sup +} ions, but also to halide ions in post-transition-metal halide melts. Second, it is conjectured that the conductivity maximum is due to rising activation energy in network-covalent (halide-bridging) melts (BiCl{sub 3}, SnCl{sub 2}, PbCl{sub 2}), but possibly a falling Arrhenius prefactor (collision frequency) for molecular melts (HgBr{sub 2}).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural and phase dependent thermo and photoluminescent properties of Dy(OH){sub 3} and Dy{sub 2}O{sub 3} nanorods

Graphical abstract: Packing diagram of (a) hexagonal Dy(OH){sub 3} and (b) cubic Dy{sub 2}O{sub 3} nanorods. Highlights: ► Hexagonal Dy(OH){sub 3} and Dy{sub 2}O{sub 3} nanorods were prepared by hydrothermal route. ► Phase dependent PL and TL studies were carried out. ► The kinetic parameters such as activation energy (E), order of kinetics (b), and frequency factor (s) were estimated using peak shape method. ► Linear response of cubic Dy{sub 2}O{sub 3} phase is useful for its application in dosimetry. -- Abstract: Hexagonal Dy(OH){sub 3} and cubic Dy{sub 2}O{sub 3} nanorods were prepared by hydrothermal method. Dy(OH){sub 3} nanorods was directly obtained at 180 °C for 20 h after hydrothermal treatment whereas subsequently heat treatment at 750 °C for 2 h gives pure cubic Dy{sub 2}O{sub 3}. SEM micrographs reveal that needle shaped rods with different sizes were observed in both the phases. TEM results also confirm this. The TL response of hexagonal Dy(OH){sub 3} and cubic Dy{sub 2}O{sub 3} nanorods have been analyzed for γ-irradiation over a wide range of exposures (1–5 kGy). TL glow peak intensity increases with γ dose in both the phases. The activation energy (E), order of kinetics (b), and frequency factor (s) for both the phases have been determined using Chen's peak shape method. The simple glow curve shape, structure and linear response to γ-irradiation over a large span of exposures makes the cubic Dy{sub 2}O{sub 3} as a useful dosimetric material to estimate high exposures of γ-rays.

36 MATERIALS SCIENCE↗

Epoxide ring opening with alcohols using heterogeneous Lewis acid catalysts: Regioselectivity and mechanism

Lewis acidic catalytic materials are investigated for the regioselective ring opening of epoxides with alcohols. For ring opening epichlorohydrin with methanol, the catalytic activity shows a strong dependence on the type of support and Lewis acidic species used. While Sn-SBA-15 is catalytically active, significantly higher catalytic activity can be achieved with hydrothermally synthesized zeolites of which Sn-Beta is 6 and 7 times more active than Zr-Beta or Hf-Beta, respectively. Sn-Beta is determined to be more active and more regioselective for epoxide ring opening of epichlorohydrin with methanol than Al-Beta. For Sn-Beta, the activation energy for the reaction between epichlorohydrin and methanol is determined to be 53 ± 7 kJ mol -1 . For epichlorohydrin, the activation energy barrier and experimentally observed regioselectivity are found using DFT to be consistent with a concerted reaction mechanism involving activation of the epoxide on an alcohol adsorbed on the catalytic site and nucleophilic attack by a second alcohol. Here, the epoxide is shown to impact the regioselectivity and the mechanism since isobutylene oxide is selectively ring opened by methanol to form the terminal alcohol. DFT calculations indicate the mechanism for isobutylene ring opening involves epoxide activation and ring opening on an alcohol adsorbed onto the catalytic site. Finally, catalyst reuse testing indicates that Sn-Beta can be used for multiple reactions with no decrease in activity and limited to no leaching of the tin site, demonstrating Sn-Beta is a promising catalytic material for epoxide ring opening reactions with alcohols.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular dynamics force-field refinement against quasi-elastic neutron scattering data

Quasi-elastic neutron scattering (QENS) is one of the experimental techniques of choice for probing the dynamics at length and time scales that are also in the realm of full-atom molecular dynamics (MD) simulations. This overlap enables extension of current fitting methods that use time-independent equilibrium measurements to new methods fitting against dynamics data. We present an algorithm that fits simulation-derived incoherent dynamical structure factors against QENS data probing the diffusive dynamics of the system. We showcase the difficulties inherent to this type of fitting problem, namely, the disparity between simulation and experiment environment, as well as limitations in the simulation due to incomplete sampling of phase space. We discuss a methodology to overcome these difficulties and apply it to a set of full-atom MD simulations for the purpose of refining the force-field parameter governing the activation energy of methyl rotation in the octa-methyl polyhedral oligomeric silsesquioxane molecule. Our optimal simulated activation energy agrees with the experimentally derived value up to a 5% difference, well within experimental error. We believe the method will find applicability to other types of diffusive motions and other representation of the systems such as coarse-grain models where empirical fitting is essential. In addition, the refinement method can be extended to the coherent dynamic structure factor with no additional effort.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Photoconductivity study of acid on Zinc phthalocyanine pyridine thin films

The Metal Phthalocyanine (MPc) have attracted much interest because of chemical and high thermal stability. Molecules forming a crystal of MPc are held together by weak attractive Vander Waals forces. Organic semiconductors have π conjugate bonds which allow electrons to move via π-electron cloud overlaps. Conduction mechanisms for organic semiconductor are mainly through tunneling; hopping between localized states, mobility gaps, and phonon assisted hopping. The photo conductivity of thin films of these complexes changes when exposed to oxidizing and reducing gases. Arrhenius plot is used to find the thermal activation energy in the intrinsic region and impurity scattering region. Arrhenius plotsare used to find the thermal activation energy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Role of deep levels and barrier height lowering in current-flow mechanism in 150 μ m thick epitaxial n-type 4H–SiC Schottky barrier radiation detectors

Schottky barrier detectors (SBDs) require larger surface areas than conventional electronics to increase the detection efficiency although such SBDs manifest large diode ideality factors due to inhomogeneous areal distribution of surface barrier height (SBH). Inhomogeneous SBH distributions lead to various current flow mechanisms in SBDs, which need to be identified to optimize detector performance. In this Letter, we identify the current flow mechanism in large area Schottky barrier diodes for radiation detection fabricated on 150 μm thick n-4H–SiC epitaxial layers. The analysis of temperature-dependent forward current–voltage (I–V–T) characteristics of SBDs revealed two linear regions in current–voltage curves up to 450 K, one corresponding to the current flow through a low barrier patch, while the other corresponds to that of average barrier distribution. Applying a SBH distribution model to the reverse I–V–T characteristics, an activation energy of 0.76 eV for the current flow over the Schottky barrier was calculated. Additionally, the activation energy did not directly correspond to any of the defect levels observed from the deep level transient spectroscopy (DLTS). Above 450 K, a Schottky type barrier lowering suggested a current flow through a low barrier patch of ≈ 0.8 eV. The absence of any SBH lowering below 450 K indicated that the current corresponded to a neutrally charged trap level at ≈ 0.6 eV below the conduction band edge, which was consistent with DLTS measurements revealing the presence of an electron trap level Z1/2 at 0.59 eV below the conduction band edge.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The Oxidation Kinetics of Continuous Carbon Fibers in a Cracked Ceramic Matrix Composite

Experimental observations and results suggest two primary regimes as a function of temperature, i.e., diffusion and reaction controlled kinetics. Thermogravimetric analysis of carbon fiber in flowing oxygen gave an activation energy of 64.1 kJ/mol in the temperature range of 500 to 600 C and an apparent activation energy of 7.6 kJ/mol for temperatures from 600 to 1400 C. When C/SiC composite material was unstressed, matrix effects at temperatures from 900 to 1400 C protected the internal fibers. When under stress, self-protection was not observed. Increasing the stress from 10 to 25 ksi caused a 67 to 82 percent reduction in times to failure at temperatures from 750 to 1500 C. Based on experimental results, observation, and theory, a finite difference model was developed, which simulates the diffusion of oxygen into a matrix crack that is bridged by carbon fibers. The model allows the influence of important variables on oxidation kinetics to be studied systematically, i.e., temperature, reaction rate constant, diffusion coefficient, environment, and sample geometry.

Halbig, Michael C.↗

Truncated Dual-Cap Nucleation Site Development

During heterogeneous nucleation within a metastable mushy-zone, several geometries for nucleation site development must be considered. Traditional spherical dual cap and crevice models are compared to a truncated dual cap to determine the activation energy and critical cluster growth kinetics in ternary Fe-Cr-Ni steel alloys. Results of activation energy results indicate that nucleation is more probable at grain boundaries within the solid than at the solid-liquid interface.

Matson, Douglas M.↗

Distribution and mobility of lithium in NASICON-type Li1-xTi2-xNbx(PO4)3 (0 ≤ x ≤ 0.5) compounds

Highlights: • Li{sub 1-x}Ti{sub 2-x}Nb{sub x}(PO{sub 4}){sub 3} (0 ≤ x ≤ 0.5) were prepared via solid-state reaction. • The substitution of Ti{sup 4+} by Nb{sup 5+} in LiTi{sub 2}(PO{sub 4}){sub 3} increases unit cell dimensions. • The Rietveld analysis of XRD patterns was performed to deduce location of Li ions. • LiTi{sub 2}(PO{sub 4}){sub 3} have the highest total conductivity and low activation energy. - Abstract: The NASICON-type Li{sub 1-x}Ti{sub 2-x}Nb{sub x}(PO{sub 4}){sub 3} (0 ≤ x ≤ 0.5) has been prepared using a conventional solid-state reaction and characterized by powder X-ray (XRD), scanning electron microscopy (SEM), nuclear magnetic resonance (NMR) and impedance spectroscopy (IS). The substitution of Ti{sup 4+} by Nb{sup 5+} in LiTi{sub 2}(PO{sub 4}){sub 3} increases unit cell parameters of NASICON phases (S.G. R 3-bar c). The parallel XRD and NMR analysis confirmed the formation of secondary phases besides NASICON compounds. The NMR components detected in {sup 93}Nb and {sup 31}P MAS-NMR spectra have been ascribed to formation of crystalline NbPO{sub 5} and NASICON phases. The substitution of Ti{sup 4+} by Nb{sup 5+} produces detection of three equally spaced {sup 31}P MAS-NMR P(OTi){sub 4-n}(ONb){sub n} components, whose intensity changes with the Nb content of the NASICON phase. On the other hand, the broad {sup 31}P NMR band detected at ∼−130 ppm has been ascribed to the formation of an amorphous Nb phosphate that strongly affects conductivity of samples. At 355 K, total conductivity decreased from 1.2 × 10{sup −7} S cm{sup −1} (Ea = 0.49 eV) to 6.0 × 10{sup −9} S cm{sup −1} (Ea = 0.56 eV) when going from LiTi{sub 2}(PO{sub 4}){sub 3} to Li{sub 0.5}Ti{sub 1.5}Nb{sub 0.5}(PO{sub 4}){sub 3}. This important decrease has been related to the increment of activation energy (stronger Li-network interaction); however, further studies are required to understand the deleterious effect of niobium in Li{sub 1-x}Ti{sub 2-x}Nb{sub x} (PO{sub 4}){sub 3} series.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature dependent simulation of diamond depleted Schottky PIN diodes

Diamond is considered as an ideal material for high field and high power devices due to its high breakdown field, high lightly doped carrier mobility, and high thermal conductivity. The modeling and simulation of diamond devices are therefore important to predict the performances of diamond based devices. In this context, we use Silvaco{sup ®} Atlas, a drift-diffusion based commercial software, to model diamond based power devices. The models used in Atlas were modified to account for both variable range and nearest neighbor hopping transport in the impurity bands associated with high activation energies for boron doped and phosphorus doped diamond. The models were fit to experimentally reported resistivity data over a wide range of doping concentrations and temperatures. We compare to recent data on depleted diamond Schottky PIN diodes demonstrating low turn-on voltages and high reverse breakdown voltages, which could be useful for high power rectifying applications due to the low turn-on voltage enabling high forward current densities. Three dimensional simulations of the depleted Schottky PIN diamond devices were performed and the results are verified with experimental data at different operating temperatures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Site Energies of Active and Inactive Pheophytins in the Reaction Center of Photosystem II from Chlamydomonas Reinhardtii

It is widely accepted that the primary electron acceptor in various Photosystem II (PSII) reaction center (RC) preparations is pheophytin {alpha} (Pheo {alpha}) within the D1 protein (Pheo{sub D1}), while Pheo{sub D2} (within the D2 protein) is photochemically inactive. The Pheo site energies, however, have remained elusive, due to inherent spectral congestion. While most researchers over the past two decades placed the Q{sub y}-states of Pheo{sub D1} and Pheo{sub D2} bands near 678-684 and 668-672 nm, respectively, recent modeling [Raszewski et al. Biophys. J. 2005, 88, 986-998; Cox et al. J. Phys. Chem. B 2009, 113, 12364-12374] of the electronic structure of the PSII RC reversed the assignment of the active and inactive Pheos, suggesting that the mean site energy of Pheo{sub D1} is near 672 nm, whereas Pheo{sub D2} ({approx}677.5 nm) and Chl{sub D1} ({approx}680 nm) have the lowest energies (i.e., the Pheo{sub D2}-dominated exciton is the lowest excited state). In contrast, chemical pigment exchange experiments on isolated RCs suggested that both pheophytins have their Q{sub y} absorption maxima at 676-680 nm [Germano et al. Biochemistry 2001, 40, 11472-11482; Germano et al. Biophys. J. 2004, 86, 1664-1672]. To provide more insight into the site energies of both Pheo{sub D1} and Pheo{sub D2} (including the corresponding Q{sub x} transitions, which are often claimed to be degenerate at 543 nm) and to attest that the above two assignments are most likely incorrect, we studied a large number of isolated RC preparations from spinach and wild-type Chlamydomonas reinhardtii (at different levels of intactness) as well as the Chlamydomonas reinhardtii mutant (D2-L209H), in which the active branch Pheo{sub D1} is genetically replaced with chlorophyll {alpha} (Chl {alpha}). We show that the Q{sub x}-/Q{sub y}-region site energies of Pheo{sub D1} and Pheo{sub D2} are {approx}545/680 nm and {approx}541.5/670 nm, respectively, in good agreement with our previous assignment [Jankowiak et al. J. Phys. Chem. B 2002, 106, 8803?8814]. The latter values should be used to model excitonic structure and excitation energy transfer dynamics of the PSII RCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of configurational changes on molecular dynamics in polyvinylidene fluoride and poly(vinylidene fluoride-trifluoroethylene) ferroelectric polymers

Here, we present a comparative study of proton dynamics in unpoled non-ferroelectric polymer polyvinylidene fluoride (PVDF) and in its trifluoroethylene containing ferroelectric copolymer (with 70/30 molar proportion), using quasi-elastic neutron scattering. The neutron data reveal the existence of two distinct types of molecular motions in the temperature range investigated. Moreover, the slower motion, which is characterized in details here, is ascribed to protons jump diffusion along the polymeric carbon chains, while the faster motion could be attributed to localized rotational motion of methylene groups. At temperatures below the Curie point (T-c similar to 385 K) of the composite polymer, the slower diffusive mode experiences longer relaxation times in the ferroelectric blend than in the bare PVDF, although the net corresponding diffusion coefficient remains comparatively the same in both polymers with characteristic activation energy of E-A approximate to 27-33 kJ/mol. This arises because of a temperature dependent jump length r(0), which we observe to be effectively longer in the copolymer, possibly due to the formation of ordered ferroelectric domains below Tc. Above Tc, there is no appreciable difference in r(0) between the two systems. Our observation directly relates the known dependence of Tc on molar ratio to changes in r(0), providing fundamental insight into the ferroelectric properties of PVDF-based copolymers.

36 MATERIALS SCIENCE↗

On the thermal stability of physical vapor deposited oxide-hardened nanocrystalline gold thin films

We describe a correlation between electrical resistivity and grain size for PVD synthesized polycrystalline oxide-hardened metal-matrix thin films in oxide-dilute (<5 vol. % oxide phase) compositions. The correlation is based on the Mayadas-Shatzkes (M-S) electron scattering model, predictive of grain size evolution as a function of composition in the oxide-dilute regime for 2 μm thick Au-ZnO films. We describe a technique to investigate grain boundary (GB) mobility and the thermal stability of GBs based on in situ electrical resistivity measurements during annealing experiments, interpreted using a combination of the M-S model and the Michels et al. model describing solute drag stabilized grain growth kinetics. Using this technique, activation energy and pre-exponential Arrhenius parameter values of E{sub a} = 21.6 kJ/mol and A{sub o} = 2.3 × 10{sup −17} m{sup 2}/s for Au-1 vol. % ZnO and E{sub a} = 12.7 kJ/mol and A{sub o} = 3.1 × 10{sup −18} m{sup 2}/s for Au-2 vol. % ZnO were determined. In the oxide-dilute regime, the grain size reduction of the Au matrix yielded a maximum hardness of 2.6 GPa for 5 vol. % ZnO. A combined model including percolation behavior and grain refinement is presented that accurately describes the composition dependent change in electrical resistivity throughout the entire composition range for Au-ZnO thin films. The proposed correlations are supported by microstructural characterization using transmission electron microscopy and electron diffraction mapping for grain size determination.

36 MATERIALS SCIENCE↗

High-temperature oxidation behavior of the SiC layer of TRISO particles in low-pressure oxygen

Surrogate tristructural-isotropic (TRISO)-coated fuel particles were oxidized in 0.2 kPa O 2 at 1200–1600°C to examine the behavior of the SiC layer and understand the mechanisms. The thickness and microstructure of the resultant SiO 2 layers were analyzed using scanning electron microscopy, focused ion beam, and transmission electron microscopy. The majority of the surface comprised smooth, amorphous SiO 2 with a constant thickness indicative of passive oxidation. The apparent activation energy for oxide growth was 188 ± 8 kJ/mol and consistent across all temperatures in 0.2 kPa O 2 . The relationship between activation energy and oxidation mechanism is discussed. Raised nodules of porous, crystalline SiO 2 were dispersed across the surface, suggesting that active oxidation and redeposition occurred in those locations. These nodules were correlated with clusters of nanocrystalline SiC grains, which may facilitate active oxidation. So these findings suggest that microstructural inhomogeneities such as irregular grain size influence the oxidation response of the SiC layer of TRISO particles and may influence their accident tolerance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Breaking the Energy Barrier of Heavy Metal Ion Diffusion in Micropores with Mesoporous 3D Graphene for Fast and Efficient Cu2+ Removal

Efficient removal of heavy metals from water critically depends not only on adsorption capacity but also on ion diffusion kinetics and the associated energy barriers. In conventional carbon adsorbents, severe diffusion confinement within micropores restricts ion transport, resulting in sluggish adsorption kinetics and large apparent activation energies despite high specific surface areas. Here, we demonstrate that this fundamental limitation is overcome by engineering meso/macroporous architectures in the 3D graphene materials synthesized via our discovered alkali-metal reactions with\\\\r\\\\n2\\\\r\\\\nCO. The unique 3D graphene materials possess defect-rich graphene frameworks with interconnected meso/macroporous networks, exhibiting simultaneously high surface area and greatly enhanced meso/macropore volume that enable efficient access to adsorption sites. As a result, the Cu2+ adsorption on 3D graphene proceeds with very low activation energies (4.98 kJ mol–1), which is almost 4 times smaller than on activated carbon (23.1 kJ mol–1). This finding offers a promising platform for efficient and sustainable water purification.

25 ENERGY STORAGE↗

Sulfidation kinetics of titanium and Ti-6Al-4V with elemental sulfur

The sulfidation kinetics of titanium and Ti-6Al-4V (Ti64) using elemental sulfur were studied by measuring the amount of metal consumed instead of the change in mass or scale thickness. Here this metal consumption approach combines the parabolic oxidation law, Arrhenius equation, and Pilling-Bedworth ratio to determine the apparent activation energy and the pre-exponential factor of consumption of Ti64 during sulfidation. The estimations of apparent activation energy and pre-exponential factor were 110.4 kJ·mol -1 and 1.3×10 -9 m 2 s -1 for the titanium-sulfur, and 116.2 kJ·mol -1 and 1.2×10 -9 m2s -1 for the Ti64-sulfur system. Finally, a material removal predictor was developed to predict the amount of Ti64 consumed for a given sulfidation temperature and time.

36 MATERIALS SCIENCE↗