Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind potential”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Utilizing Modal Testing for Monitoring the Structural Health of Wind Tunnel Facility Hardware

The 10- by 10-Foot Abe Silverstein Supersonic Wind Tunnel (10×10) is the largest and fastest wind tunnel facility at NASA’s Glenn Research Center(GRC) and is specifically designed to test supersonic propulsion components from inlets and nozzles to full-scale jet and rocket engines[1]. Recently, a critical part of the wind tunnel failed and required a redesign before reintegrating into the facility. The design requirements of this new component required that clearances between large metallic components exist, which have the potential for undesirable nonlinear dynamics to occur, in particular rattling. Rattling is feared to occur when the wind tunnel is being operated in certain flow regimes that induce cyclic aero loads on the new component near its natural frequencies. This paper describes the approach taken to better understand and resolve this vibration problem using modal testing. A modal test was developed and executed by GRC’s Structural Dynamics Lab to quantify the modal parameters of the structure, namely which specific excitation frequencies caused the structure to rattle. These results were shared with facility operators as frequency ranges that should be avoided to ensure maximum lifespan of the new structure. Additional means of structural health monitoring (SHM) as well as Vortex shedding are briefly discussed in this paper.

Pederson, Kenneth↗
NASA NTRS1981

Determination of magnetic helicity in the solar wind and implications for cosmic ray propagation

Magnetic helicity (Hm) is the mean value of the correlation between a turbulent magnetic field and the magnetic vector potential. A technique is described for determining Hm and its 'reduced' spectrum from the two point magnetic correlation matrix. The application of the derived formalism to solar wind magnetic fluctuations is discussed, taking into account cases for which only single point measurements are available. The application procedure employs the usual 'frozen in approximation' approach. The considered method is applied to an analysis of several periods of Voyager 2 interplanetary magnetometer data near 2.8 AU. During these periods the correlation length, or energy containing length, was found to be approximately 3 x 10 to the 11th cm

Matthaeus, W. M.↗
NASA NTRS1980

Deep convection on day 261 of GATE

The structural features of the deep convection observed on September 18, 1974, day 261 of the GARP Atlantic Tropical Experiment (GATE), as the ridge axis of a 700 mb wave passed the center of the GATE B-scale network are reported. Satellite and aircraft maps indicate the presence of clouds penetrating above 2.5 km into the middle troposphere organized in bands about 9 km apart and aligned roughly along the direction of the wind shear in the cloud layer. Radar echoes corresponding to cumulus convection of lifetime, peak height and peak rainfall rates on the orders of 30 min, 6 km and 1.3 mm/h, respectively, were observed to triple in number density as convergence at 950 hPa increased from 1.5 to 3 x 10 to the -5th/sec. The structural features of the radar echoes indicate that the day was similar to a mesoscale precipitation feature of Leary and Houe (1979), with the cluster consisting of many echoes appearing in succession. Data from aircraft penetrations of the deep convection reveal downdrafts accompanying the precipitation and updrafts immediately to their south. Shipboard and rawinsonde observations show that the convective downdrafts brought down air of low pseudo-equivalent potential temperature, with local surface convergence of up to 0.001/sec. Mean wind shears through the cloud layer to the top of a main cloud layer are found to be only 75% greater than those of Malkus (1958) for the Caribbean, with shears just above the cloud base several factors larger.

Warner, C.↗
NASA NTRS2019

A Qualitative Investigation of Selected Infrared Flow Visualization Image Processing Techniques

The deployment and integration of high-sensitivity infrared cameras in a transonic wind tunnel testenvironment has resulted in a unique capability to image aerodynamic phenomena in real-time. Multi-camera infrared flow visualization data systems are now routinely utilized at the NASA Ames Unitary Plan Wind Tunnel. The small flow-induced temperature gradients on the surface of the wind tunnel test article coupled with the high bit-depth of the infrared camera sensor makes the processing of the image data critically important. An image processing routine must enhance features of interest with minimal artifacts. Additionally, the production wind tunnel test environment demands that these processed images are made available in a real-time, automatic fashion. Therefore, any image processing routine must be computationally economical and enhance the image data with minimal input from a human operator. The following seeks to qualitatively explore selected image processing techniques by assessing their effectiveness to resolve flow features on a wind tunnel test article. A multi-scale contrast enhancement technique is discussed as well as a new implementation of a multi-scale, non-interpolated adaptive histogram equalization. Finally, a novel method is introduced that demonstrates the ability to resolve flow features imaged on bare-steel test articles possessing low emissivity.This method makes use of dynamic mode decomposition and discrete-time filtering to separate the background reflections that dominate low emissivity surfaces from the aerodynamic driven surface temperature gradients.This process will be shown to resolve the onset of boundary layer transition on a bare metal wing as well as identify and resolve hidden features in the image data. While the implementation of this technique is very preliminary it demonstrates the potential to extend the application of infrared flow-visualization within the wind tunnel test environment.

Image Processeing↗
NASA NTRS2004

NASCAP-2K: An Overview

Nascap-2k is the modern replacement for the older 3-D charging codes NASCAP/GEO, NASCAP/LEO, POLAR, and DynaPAC. Built on the DynaPAC kernel and incorporating surface charging, environment and space potential models from the older codes, Nascap-2k performs charging calculations for a wide variety of space environments under control of a unified graphical interface. In this paper we illustrate the use of Nascap-2k for spacecraft charging calculations. We touch on some of the unique physical and mathematical models on which the code is based. Examples/demos include the use of Object Toolkit, charging calculations in geosynchronous substorm, solar wind, low earth orbit, and auroral environments, and display and analysis of surface potentials, space potentials and particle trajectories.

Mandell, M. J.↗
NASA NTRS1972

Experimental measurements of 2.25-cm backscatter from sea surfaces.

Airborne 2.25-cm wavelength radar backscatter measurements of low-wind-speed sea conditions were obtained off the coast of Texas in January 1971. These data are compared with unpublished NASA 2.25-cm backscatter measurements recorded over the Atlantic in 1970. The two data sets were in general agreement and supported results previously reported by other authors which showed the absence of a saturation effect at this wavelength. Analyses of these data using computerized clustering techniques indicated that a wind speed measurement accuracy of 5-7 knots is an operational potential.

Newton, R. W.↗
NASA NTRS1978

Large wind turbine generators

The development associated with large wind turbine systems is briefly described. The scope of this activity includes the development of several large wind turbines ranging in size from 100 kW to several megawatt levels. A description of the wind turbine systems, their programmatic status and a summary of their potential costs is included.

Thomas, R. L.↗
NASA NTRS1978

Large wind turbine generators

The large wind turbine portion of the Federal Wind Energy Program consists of two major project efforts: (1) the Mod-0 test bed project for supporting research technology, and (2) the large experimental wind turbines for electric utility applications. The Mod-0 has met its primary objective of providing the entire wind energy program with early operations and performance data. The large experimental wind turbines to be tested in utility applications include three of the Mod-0A (200 kW) type, one Mod-1 (2000 kW), and possibly several of the Mod-2 (2500 kW) designs. This paper presents a description of these wind turbine systems, their programmatic status, and a summary of their potential costs.

Thomas, R. L.↗
NASA NTRS1979

An empirical polytrope law for solar wind thermal electrons between 0.45 and 4.76 AU: Voyager 2 and Mariner 10

Empirical evidence is presented that solar wind thermal electrons obey a polytrope law with polytrope index gamma = 1.175 plus or minus 0.03. The Voyager 2 and Mariner 10 data used as evidence are compared and discussed. The theoretical predictions that solar wind thermal electrons in the asymptotic solar wind should obey a polytrope law with polytrope index gamma = 1.16 plus or minus. The widespread impressions in the literature that solar wind electrons behave more like an isothermal than adiabatic gas, and the arguments that Coulomb collisions are the dominant stochastic process shaping observed electron distribution functions in the solar wind are reexamined, reviewed and evaluated. The assignment of the interplanetary potential as equal to approximately seven times the temperature of the thermal electrons is discussed.

Sittler, E. C., Jr.↗
NASA NTRS1979

Control considerations for CCV fighters at high angles of attack

Wind tunnel and piloted simulation studies were conducted to investigate the potential high angle of attack control problems that are introduced by the use of the CCV concept of relaxed static pitch stability (RSS) on fighter aircraft. A conventional wing/aft tail design incorporating modest levels of static instability and a close-coupled canard/wing design exhibiting very high levels of instability was investigated. Two types of high angle of attack control problems can result from the use of RSS: pitch departures caused by coupling and deep stall trim. Avoidance of these problems requires that the airplane have sufficient nose-down pitch control at high angles of attack. The effectiveness of several pitch control configurations were investigated including conventional aft-mounted stabilators, wing-mounted elevators, canard-mounted flaps, and all-moveable canards. Varying the incidence of the canards was the most effective scheme; however, very large deflections may be required on highly unstable configurations to prevent pitch departure without sacrificing roll performance and to avoid deep stall trim. For situations where the high angle of attack pitch control requirement is not met, control laws were developed to inhibit the departure and to allow deep stall recovery. However, these schemes involve limiting airplane roll capability and therefore can potentially compromise maneuverability.

Nguyen, L. T.↗
NASA NTRS1981

Wind-tunnel studies of advanced cargo aircraft concepts

Accomplishments in vortex flap research are summarized. A singular feature of the vortex flap is that, throughout the range of angle of attack range, the flow type remains qualitatively unchanged. Accordingly, no large or sudden change in the aerodynamic characteristics, as happens when forcibly maintained attached flow suddenly reverts to separation, will occur with the vortex flap. Typical wind tunnel test data are presented which show the drag reduction potential of the vortex flap concept applied to a supersonic cruise airplane configuration. The new technology offers a means of aerodynamically augmenting roll-control effectiveness on slender wings at higher angles of attack by manipulating the vortex flow generated from leading edge separation. The proposed manipulator takes the form of a flap hinged at or close to the leading edge, normally retracted flush with the wing upper surface to conform to the airfoil shape.

Rao, D. M.↗
NASA NTRS1984

Reel Down - A balloon borne winch system for stratospheric sounding from above

A balloon-borne winch system has been developed and flight tested which permits the repetitive lowering and hoisting of a stratospheric sampling payload for distances of up to 20 km from a float altitude of 35-40 km. This new approach to in situ stratospheric measurements permits multiple scans of various depths and velocities, closely spaced over a period of hours or days, thus dramatically increasing observational effectiveness. The motor driven winch permits control of ascent velocities from 0-9 m/s with energy derived from a large battery; for descent, the motors are used as generators, velocity is controlled over the same range, and the energy is dumped radiatively to space. The 1.75 mm diameter tether is of braided Kevlar construction with a nylon jacket; it exhibits a 2900 N break strength. Both the winch and the payload suspended by the tether are fully instrumented to evaluate potentially destructive system-induced dynamics and the effects of stratospheric wind shears. The system was successfully flight tested by lowering a 62 kg payload for a distance of 12 km from a float altitude of 38.5 km and hoisting it back up again, both at velocities ranging between 5-9 m/s. Observations indicated minimal system-induced dynamical effects, and no adverse effects due to the 8 m/s wind shear present during flight.

Hazen, N. L.↗
NASA NTRS1990

Turbulence measurements using tethered balloon instrumentation during FIRE 1987

As part of the surface-based observations conducted on San Nicolas Island, the U.K. Meteorological Office operated a set of turbulence probes attached to a balloon tether cable. Typically six probes were used, each capable of measuring momentum, heat, and humidity fluxes. Two probes were fitted with net radiometers, one positioned above cloud and the other below; a third probe carried a Lyman-alpha hygrometer fitted with a pre-heater for the measurement of total water content. Some preliminary results are presented from the 14th July describing the variation in structure of the cloudy boundary layer during the daytime. This day was characterized by a complete cloud cover, an inversion height of approximately 600 m. and north-westerly winds of approximately 6 m.s(-1). As an illustration the equivalent potential temperature derived from a profile ascent made between approximately 0830 and 0930 (PDT) is shown. The data has been smoothed to a height resolution of about 4 metres. At this time the cloud base was approximately 200 m. and very light drizzle was reaching the surface. The vertical velocity variance and potential temperature flux for two periods are shown; the first (shown by full lines) immediately follows the profile and the second (shown by dashed lines) is central around 1400 (PDT). The data have been normalized by their maximum values in the first period. Cloud base has now risen to approximately 300 m. There is a marked variation during the morning, particularly in sigma w. The net radiative flux above cloud top has by now reached its maximum value.

Hignett, Phillip↗
NASA NTRS1990

The Joint NASA/Goddard-University of Maryland Research Program in Charged Particle and High Energy Photon Detector Technology

The Univ. of Maryland portion investigated the following areas. The Space Physics Group performed studies of data from the AMPTE/CCE spacecraft CHEM experiment and found that the ratio of solar wind to photospheric abundances decreased rather smoothly with the first ionization potential (FIP) of the ion with the low FIP ion being about a factor of two overabundant. Carbon and hydrogen fit this trend particularly well. Several occurrences were analyzed of field aligned beams observed when CCE was upstream of the Earth's bow shock. Also using CHEM data, ring current intensity and composition changes during the main and recovery phases of the great geomagnetic storm that occurred in February 1986 was examined in detail. Still using CHEM data, ring current characteristics were examined in a survey of 20 magnetic storms ranging in size from -50 nT to -312 nT. A study was done of energetic ion anisotropy characteristics in the Earth's magnetosheath region using data from the UMD/MPE experiment on ISEE-1. The properties were analyzed of approx. 30 to 130 keV/e protons and alpha particles upstream of six quasi-parallel interplanetary shocks that passed by the ISEE-3 spacecraft during 1978 to 1979. Work from NASA-Goddard include studies from the High Energy Cosmic Ray Group, Low Energy Cosmic Ray Group, Low Energy Gamma Ray Group, High Energy Astrophysics Theory Group, and the X ray Astronomy Group.

Ipavich, F. M.↗
NASA NTRS1992

Advanced stitching technology

In the design of textile composites, the selection of materials and constructional techniques must be matched with product performance, productivity, and cost requirements. Constructional techniques vary. A classification of various textile composite systems is given. In general, the chopped fiber system is not suitable for structural composite applications because of fiber discontinuity, uncontrolled fiber orientation and a lack of fiber integration or entanglement. Linear filament yarn systems are acceptable for structural components which are exposed to simple tension in their applications. To qualify for more general use as structural components, filament yarn systems must be multi-directionally positioned. With the most sophisticated filament winding and laying techniques, however, the Type 2 systems have limited potential for general load-bearing applications because of a lack of filament integration or entanglement, which means vulnerability to splitting and delamination among filament layers. The laminar systems (Type 3) represented by a variety of simple fabrics (woven, knitted, braided and nonwoven) are especially suitable for load-bearing panels in flat form and for beams in a roled up to wound form. The totally integrated, advanced fabric system (Type 4) are thought to be the most reliable for general load-bearing applications because of fiber continuity and because of controlled multiaxial fiber orientation and entanglement. Consequently, the risk of splitting and delamination is minimized and practically omitted. Type 4 systems can be woven, knitted, braided or stitched through with very special equipment. Multiaxial fabric technologies are discussed.

Scardino, Frank L.↗
NASA NTRS1999

The Earth System Science Pathfinder VOLCAM Volcanic Hazard Mission

The VOLCAM mission is planned for research on volcanic eruptions and as a demonstration of a satellite system for measuring the location and density of volcanic eruption clouds for use in mitigating hazards to aircraft by the operational air traffic control systems. A requirement for 15 minute time resolution is met by flight as payloads of opportunity on geostationary satellites. Volcanic sulfur dioxide and ash are detected using techniques that have been developed from polar orbiting TOMS (UV) and AVHRR (IR) data. Seven band UV and three band IR filter wheel cameras are designed for continuous observation of the full disk of the earth with moderate (10 - 20 km) ground resolution. This resolution can be achieved with small, low cost instruments but is adequate for discrimination of ash and sulfur dioxide in the volcanic clouds from meteorological clouds and ozone. The false alarm rate is small through use of sulfur dioxide as a unique tracer of volcanic clouds. The UV band wavelengths are optimized to detect very small sulfur dioxide amounts that are present in pre-eruptive outgassing of volcanoes. The system is also capable of tracking dust and smoke clouds, and will be used to infer winds at tropopause level from the correlation of total ozone with potential vorticity.

Krueger, Arlin J.↗
NASA NTRS2000

Remote Sensing of Wind Fields and Aerosol Distributions with Airborne Scanning Doppler Lidar

The coherent Doppler lidar, when operated from an airborne platform, offers a unique measurement capability for study of atmospheric and surface processes and feature. This is especially true for scientific objectives requiring measurements in optically-clear air, where other remote sensing technologies such as Doppler radar are at a disadvantage in terms of spatial resolution and coverage. The atmospheric lidar remote sensing groups of several US institutions, led by Marshall Space Flight Center, have developed an airborne coherent Doppler lidar capable of mapping the wind field and aerosol structure in three dimensions. The instrument consists of about a 1 Joule/pulse (eyesafe) lidar transceiver, telescope, scanner, inertial measurement unit, and operations control system to orchestrate all subsystem functions and tasks. The scanner is capable of directing the expanded lidar beam in a variety of ways, in order to extract vertically resolved wind fields. Horizontal resolution is about 1 km; vertical resolution is even finer. Winds are obtained by measuring backscattered, Doppler-shifted laser radiation from naturally-occurring aerosol particles (on an order of 1 micron in diameter). Measurement coverage depends on aerosol spatial distribution and concentration. Velocity accuracy has been verified to be about 1 m/s. A variety of applications has been demonstrated during the three flight campaigns conducted during 1995-1998. Examples will be shown during the presentation. In 1995, boundary layer winds over the ocean were mapped with unprecedented resolution. In 1996, unique measurements were made of flow over the complex terrain of the Aleutian Islands; interaction of the marine boundary layer jet with the California coastal mountain range; a weak dry line in Texas - New Mexico; an upper tropospheric jet stream; the angular dependence of sea surface scattering; and in-flight radiometric calibration using the surface of White Sands National Monument. In 1998, the first measurements of eyewall and boundary layer winds within a hurricane were made with the airborne Doppler lidar. Potential future applications, and plans for improvements, will also be identified.

Rothermel, Jeffry↗