Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “torque control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Integrated Power and Attitude Control System Demonstrated With Flywheels G2 and D1

On September 14, 2004, NASA Glenn Research Center's Flywheel Development Team experimentally demonstrated a full-power, high-speed, two-flywheel system, simultaneously regulating a power bus and providing a commanded output torque. Operation- and power-mode transitions were demonstrated up to 2000 W in charge and 1100 W in discharge, while the output torque was simultaneously regulated between plus or minus 0.8 N-m. The G2 and D1 flywheels--magnetically levitated carbon-fiber wheels with permanent magnet motors--were used for the experiment. The units were mounted on an air bearing table in Glenn's High Energy Flywheel Facility. The operational speed range for these tests was between 20,000 and 60,000 rpm. The bus voltage was regulated at 125 V during charge and discharge, and charge-discharge and discharge-charge transitions were demonstrated by changing the amount of power that the power supply provided between 300 and 0 W. In a satellite system, this would be the equivalent of changing the amount of energy that the solar array provides to the spacecraft. In addition to regulating the bus voltage, we simultaneously controlled the net torque produced by the two flywheel modules. Both modules were mounted on an air table that was restrained by a load cell. The load cell measured the force on the table, and the torque produced by the two flywheels on the table could be calculated from that measurement. This method was used to measure the torque produced by the modules, yielding net torques from -0.8 to 0.8 N-m. This was the first Glenn demonstration of the Integrated Power and Attitude Control System (IPACS) at high power levels and speeds.

Jansen, Ralph H.↗
NASA NTRS1991

Thermal elastic shock and its effect on TOPEX spacecraft attitude control

Thermal elastic shock (TES) is a twice per orbit impulsive disturbance torque experienced by low-Earth orbiting spacecraft. The fundamental equations used to model the TES disturbance torque for typical spacecraft appendages (e.g., solar arrays and antenna booms) are derived in detail. In particular, the attitude-pointing performance of the TOPEX spacecraft, when subjected to the TES disturbance, is analyzed using a three-axis nonlinear time-domain simulation. Results indicate that the TOPEX spacecraft could exceed its roll-axis attitude-control requirement during penumbral transitions, and remain in violation for approximately 150 sec each orbit until the umbra collapses. A localized active-control system is proposed as a solution to minimize and/or eliminate the degrading effects of the TES disturbance.

Zimbelman, Darrell F.↗
NASA NTRS1973

A fine pointing system for the large space telescope

The large space telescope (LST) developed by NASA requires ultrahigh pointing stability within 0.0005 arc sec rms. A fine guidance system is proposed to body-point the entire spacecraft within this limit. The spacecraft is modeled as a rigid body having reaction wheel actuators and subject to gravitational and magnetic disturbance torques. The fine guidance sensor is cluttered with electronic noise. The disturbance accommodation standard deviation optimal controller (DASOC) is designed to be optimal with respect to the transient and the steady state response to noise, whereas the steady state response to deterministic external torques is exactly zero. Compared with conventional controllers, the fine guidance system with the DASOC offers as much as a factor of 30 improvement in pointing stability, resulting in an optimal performance of nearly 0.0001 arc sec rms. Thus, the required pointing stability can easily be obtained, and a large margin remains for the compensation of possibile deteriorations.

Schiehlen, W. O.↗
NASA NTRS1993

A gimbaled low noise momentum wheel

The bus actuators are the heart and at the same time the Achilles' heel of accurate spacecraft stabilization systems, because both their performance and their perturbations can have a deciding influence on the achievable pointing accuracy of the mission. The main task of the attitude actuators, which are mostly wheels, is the generation of useful torques with sufficiently high bandwidth, resolution and accuracy. This is because the bandwidth of the whole attitude control loop and its disturbance rejection capability is dependent upon these factors. These useful torques shall be provided, without - as far as possible - parasitic noise like unbalance forces and torques and harmonics. This is because such variable frequency perturbations excite structural resonances which in turn disturb the operation of sensors and scientific instruments. High accuracy spacecraft will further require bus actuators for the three linear degrees of freedom (DOF) to damp structural oscillations excited by various sources. These actuators have to cover the dynamic range of these disturbances. Another interesting feature, which is not necessarily related to low noise performance, is a gimballing capability which enables, in a certain angular range, a three axis attitude control with only one wheel. The herein presented Teldix MWX, a five degree of freedom Magnetic Bearing Momentum Wheel, incorporates all the above required features. It is ideally suited to support, as a gyroscopic actuator in the attitude control system, all High Pointing Accuracy and Vibration Sensitive space missions.

Bichler, U.↗
NASA NTRS2016

Magnetospheric Multiscale Mission Attitude Dynamics: Observations from Flight Data

Extensive flight data is being collected throughout the MMS mission that includes quantities that are of interest for attitude dynamics studies such as spin rate, spin axis orientation nutation rate, etc. One example of such data is the long-term evolution of the spin rates of the four spacecraft. Spikes in these rates are observed that are separated by the MMS orbital period (just under 24 hr) and occur around perigee due to gravity-gradient torque. Periodic discontinuities in spin rate are caused by the controller resetting the spin rate approximately to the nominal 3.1 RPM value at the time of each maneuver. In between, a slow decay in spin rate can be seen to occur. The paper will discuss various disturbance torque mechanisms that could potentially be responsible for this behavior: these include magnetic hysteresis, eddy currents, solar radiation pressure, and a possible interaction between gravity-gradient and wire boom flexibility effects. One additional disturbance mechanism is produced by the Active Spacecraft Potential Control (ASPOC) devices: these emit positive indium ions to keep the MMS spacecraft electrically neutral, so as not to corrupt the electric field observations that are made by some of the on-board instruments. The spin rate decays that could be produced by these various mechanisms will be quantified in the paper, and their signatures described. Comparing these with the observations from flight data then allow the most likely candidate to be determined.

DYNAMICS↗
NASA NTRSDate not supplied

Momentum Management Strategies for Solar Cruiser and Beyond (ISSS 2023)

Solar Cruiser is a small (ESPA-class) satellite Technology Demonstration Mission (TDM) to mature solar sail propulsion technology using a solar sail larger than 1600 square meters, demonstrating performance both as a propulsion system and a stable pointing platform for science observations in an artificial halo orbit sunward of the Sun-Earth Lagrange Point 1 (sub-L1). To ensure attitude control throughout the mission, momentum accumulated on the reaction wheels (RWs) used for attitude control must be managed such that the sailcraft does not lose control due to RW momentum saturation. Momentum builds up on the wheels from environmental disturbance torques caused by solar radiation pressure combined with a center of mass (CM)/center of pressure (CP) offset, deformed sail shape, and an off-sun pointing angle, plus other factors. Solar Cruiser mitigates this momentum build up by utilizing an Active Mass Translator (AMT) that maintains pitch and yaw momentum by trimming the CM/CP offsets, and thrusters to maintain roll momentum. A survey was conducted by the Solar Cruiser team to assess the feasibility and tradeoffs of novel momentum management concepts such as Reflectivity Control Devices (RCD’s), different thruster configurations, and control vanes and other articulated control surfaces. In addition, techniques to reduce disturbance torque buildup, such as reducing boom tip deflections and clock angle control, were assessed. Similar sailcraft momentum management strategies can be used for future missions such as space weather monitoring and Earth magnetotail science missions

Solar Sail↗
NASA NTRS1972

Development of a space qualified high reliability rotary actuator for spaceflight use. Volume 2: Appendices to technical report

A space-qualified, high reliability, 150 ft-lb rated torque rotary actuator is described. This drive is an integrated variable reluctance orbit motor-epicyclic transmission actuator. The performance goals were based on future control moment gyrotorquer applications and represent an advancement in the torque-to-weight ratio, backlash, inertia and response characteristics of electric rotary drives. The program accomplishments have been in two areas (1) the development of two high ratio (818:1) actuator configurations (breadboard and flightweight) and (2) the invention of a reliable proximity switch sensor system for self-commutation without use of optical or electrical brush techniques.

Presley, R. W.↗
NASA NTRS1971

Improved ITOS attitude control system with Hall generator brushless motor and earth-splitting technique

The ITOS with an improved attitude control system is described. A Hall generator brushless dc torque motor will replace the brush dc torque motor on ITOS-I and ITOS-A (NOAA-1). The four attitude horizon sensors will be replaced with two CO2 sensors for better horizon definition. An earth horizon splitting technique will be used to keep the earth facing side of the satellite toward earth even if the desired circular orbit is not achieved. The external appearance of the pitch control subsystem differs from TIROS-M (ITOS-1) and ITOS-A (NOAA-1) in that two instead of one pitch control electronics (PCE) boxes are used. Two instead of four horizon sensors will be used and one instead of two mirrors will be used for sensor scanning. The brushless motor will eliminate the requirement for brushes, strain gages and the telemetry for the brush wear. A single rotating flywheel, supported by a single bearing provides the gyroscopic stability and the required momentum interchange to keep one side of the satellite facing the earth. Magnetic torquing against the earth's magnetic field eliminates the requirement for expendable propellants which would limit satellite life in orbit.

Peacock, W. M.↗
NASA NTRS2002

Sensorimotor integration in human postural control

It is generally accepted that human bipedal upright stance is achieved by feedback mechanisms that generate an appropriate corrective torque based on body-sway motion detected primarily by visual, vestibular, and proprioceptive sensory systems. Because orientation information from the various senses is not always available (eyes closed) or accurate (compliant support surface), the postural control system must somehow adjust to maintain stance in a wide variety of environmental conditions. This is the sensorimotor integration problem that we investigated by evoking anterior-posterior (AP) body sway using pseudorandom rotation of the visual surround and/or support surface (amplitudes 0.5-8 degrees ) in both normal subjects and subjects with severe bilateral vestibular loss (VL). AP rotation of body center-of-mass (COM) was measured in response to six conditions offering different combinations of available sensory information. Stimulus-response data were analyzed using spectral analysis to compute transfer functions and coherence functions over a frequency range from 0.017 to 2.23 Hz. Stimulus-response data were quite linear for any given condition and amplitude. However, overall behavior in normal subjects was nonlinear because gain decreased and phase functions sometimes changed with increasing stimulus amplitude. "Sensory channel reweighting" could account for this nonlinear behavior with subjects showing increasing reliance on vestibular cues as stimulus amplitudes increased. VL subjects could not perform this reweighting, and their stimulus-response behavior remained quite linear. Transfer function curve fits based on a simple feedback control model provided estimates of postural stiffness, damping, and feedback time delay. There were only small changes in these parameters with increasing visual stimulus amplitude. However, stiffness increased as much as 60% with increasing support surface amplitude. To maintain postural stability and avoid resonant behavior, an increase in stiffness should be accompanied by a corresponding increase in damping. Increased damping was achieved primarily by decreasing the apparent time delay of feedback control rather than by changing the damping coefficient (i.e., corrective torque related to body-sway velocity). In normal subjects, stiffness and damping were highly correlated with body mass and moment of inertia, with stiffness always about 1/3 larger than necessary to resist the destabilizing torque due to gravity. The stiffness parameter in some VL subjects was larger compared with normal subjects, suggesting that they may use increased stiffness to help compensate for their loss. Overall results show that the simple act of standing quietly depends on a remarkably complex sensorimotor control system.

NASA Discipline Neuroscience↗
NASA NTRS1981

Magnetic control systems for large spacecraft with applications to space telescope

Magnetic control systems for large space vehicles offer the advantage of a simple, reliable, low cost augmentation to the primary control system. When used for momentum management, a magnetic torque source offers a long life and noncontaminant environment when compared to a mass expulsion torque source. These qualities make such systems suitable for employment with the Space Telescope, which is a long life, high performance vehicle with optics and scientific instruments which would be degraded by contamination due to mass expulsion products. The various applications of magnetic systems on the Space Telescope are considered. The future trend in magnetic control of large space vehicles lies in providing a known three axis reference for backup operations, such as recovery of the primary control mode.

Dougherty, H.↗
NASA NTRS1981

Adaptive control system for large annular momentum control device

A dual momentum vector control concept, consisting of two counterrotating rings (each designated as an annular momentum control device), was studied for pointing and slewing control of large spacecraft. In a disturbance free space environment, the concept provides for three axis pointing and slewing capabilities while requiring no expendables. The approach utilizes two large diameter counterrotating rings or wheels suspended magnetically in many race supports distributed around the antenna structure. When the magnets are energized, attracting the two wheels, the resulting gyroscopic torque produces a rate along the appropriate axis. Roll control is provided by alternating the radiative rotational velocity of the two wheels. Wheels with diameters of 500 to 800 m and with sufficient momentum storage capability require rims only a few centimeters thick. The wheels are extremely flexible; therefore, it is necessary to account for the distributed nature of the rings in the design of the bearing controllers. Also, ring behavior is unpredictably sensitive to ring temperature, spin rate, manufacturing imperfections, and other variables. An adaptive control system designed to handle these problems is described.

Montgomery, R. C.↗
NASA NTRS1992

Evaluation of force-torque displays for use with space station telerobotic activities

Recent experiments which addressed Space Station remote manipulation tasks found that tactile force feedback (reflecting forces and torques encountered at the end-effector through the manipulator hand controller) does not improve performance significantly. Subjective response from astronaut and non-astronaut test subjects indicated that force information, provided visually, could be useful. No research exists which specifically investigates methods of presenting force-torque information visually. This experiment was designed to evaluate seven different visual force-torque displays which were found in an informal telephone survey. The displays were prototyped in the HyperCard programming environment. In a within-subjects experiment, 14 subjects nullified forces and torques presented statically, using response buttons located at the bottom of the screen. Dependent measures included questionnaire data, errors, and response time. Subjective data generally demonstrate that subjects rated variations of pseudo-perspective displays consistently better than bar graph and digital displays. Subjects commented that the bar graph and digital displays could be used, but were not compatible with using hand controllers. Quantitative data show similar trends to the subjective data, except that the bar graph and digital displays both provided good performance, perhaps do to the mapping of response buttons to display elements. Results indicate that for this set of displays, the pseudo-perspective displays generally represent a more intuitive format for presenting force-torque information.

Hendrich, Robert C.↗
NASA NTRS1996

Pulsed plasma thrusters for small spacecraft attitude control

Pulsed Plasma Thrusters (PPTS) are a new option for attitude control of a small spacecraft and may result in reduced attitude control system (ACS) mass and cost. The primary purpose of an ACS is to orient the spacecraft to the desired accuracy in inertial space. The ACS functions for which the PPT system will be analyzed include disturbance torque compensation, and slewing maneuvers such as sun acquisition for which the small impulse bit and high specific impulse of the PPT offers unique advantages. The NASA Lewis Research Center (LERC) currently has a contracted flight PPT system development program in place with Olin Aerospace with a delivery date of October 1997. The PPT systems in this study are based upon the work being done under the NASA LERC program. Analysis of the use of PPTs for ACS showed that the replacement of the standard momentum wheels and torque rods with a PPT system to perform the attitude control maneuvers on a small low Earth orbiting spacecraft reduced the ACS mass by 50 to 75% with no increase in required power level over comparable wheel-based systems, though rapid slewing power requirements may present an issue.

McGuire, Melissa L.↗
NASA NTRS1982

Multivariable frequency domain controller for magnetic suspension and balance systems

The magnetic suspension and balance system for an airplane model in a large wind tunnel is considered. In this system, superconducting coils generate magnetic forces and torques on the magnetized soft iron core of the airplane model. The control system is a position servo where the airplane model, with six degrees of feedom, follows the reference static or dynamic input commands. The controller design, based on the characteristic loci method, minimizes the effects of aerodynamic and inertial cross-couplings, and provides the specified dynamic response.

Baheti, R. S.↗
NASA NTRS1980

Orbit-averaged behavior of magnetic control laws for momentum unloading

Analytical formulas are derived for orbit-averaged behavior of magnetic control laws for unloading the excess angular momentum of a spacecraft reaction wheel control system in the presence of secular environmental torques. The specific example of an axially symmetric spacecraft with an inertially fixed attitude for which the dominant environmental torque is the gravity-gradient torque is treated in detail, but extensions of the general approach to other inertially fixed and earth-pointing spacecraft are discussed. The analytical formulas are compared to detailed simulations performed for the Solar Maximum Mission spacecraft, and agreement to within 10% is found. The analytical formulas can be used in place of detailed simulations for preliminary studies, and can be used to find selected cases giving the most stringent tests of momentum unloading capability for which detailed simulations may be performed.

Camillo, P. J.↗
NASA NTRS1982

Effect of space flight on bone strength

To test the possibility that spaceflight has a deleterious effect on bone mechanical properties, femur breaking strength by torsional loading in rats that had been flown for 19 days aboard Cosmos 936 was determined. The results showed that femurs from flight rats were less stiff than the flight controls, and failed under torsion at a lower torque and energy of absorption. The defect was corrected following space flight and could be prevented during space flight by centrifuging the rats at 1 x g. Altered bone geometry due to inhibition of bone formation at the periosteal surface provides the most likely explanation for the decrease in bone strength during spaceflight.

Spengler, D. M.↗