Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “temperature effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

The effect of discharge chamber wall temperature on ion thruster performance

Experiments conducted on a ring cusp ion thruster that could be maintained at temperatures in the range 80 K to 500 K during operation by cooling it with liquid nitrogen are described. The measured changes in performance induced by discharge chamber wall temperature changes are compared to those predicted by a simple discharge chamber model. Good agreement between the temperature induced effects predicted by the model and measured results are demonstrated. Decreases in wall temperature to about 90 K are shown to effect substantial improvements in performance.

Wilbur, P. J.↗
NASA NTRS1972

Far-infrared brightness temperatures of the planets.

An airborne telescope operating in an altitude range from 45,000 to 50,000 feet together with a low-temperature germanium bolometer and six cooled filters were used in an investigation of the temperatures of the planets. The measurements conducted provide a basis for absolute calibration in the far infrared, confirm the high effective temperature and internal power of Jupiter, and give information on the far-infrared opacities and emissivities of the four bright planets.

Armstrong, K. R.↗
NASA NTRS1976

Crack growth in Ti-8Al-1Mo-1V with real-time and accelerated flight-by-flight loading

Crack growth in Ti-8Al-1Mo-1V was measured and calculated for real-time and accelerated simulations of supersonic airplane loading and heating. Crack-growth rates calculated on the assumption that an entire flight could be represented by a single cycle predicted the experimental rates poorly. Calculated crack-growth rates were slower than the experimental rates for all tests with flight-by-flight loading. For room-temperature accelerated tests, the calculated rates agreed well with the experimental rates; but the calculations became progressively less accurate for progressively more complex test conditions (tests that included elevated temperature). Calculations of crack growth using the crack-closure concept can probably be improved through study of crack-opening stresses using finite-element models that account for variable-amplitude loading, residual stresses, and temperature effects. The calculations of crack growth could also be improved through detailed studies of material properties and interactions among stress, temperature, and time as appropriate for the real-time operating conditions of a supersonic transport airplane.

Imig, L. A.↗
NASA NTRS1985

On the observed properties and long-term structure and evolution of white dwarfs in cataclysmic variables

An attempt is made to explain the observed surface temperatures and luminosities of cataclysmic variable white dwarfs based on the cooling physics and time-averaged structure of the white dwarf in response to accretion. The evolutionary changes in core temperature and core luminosity as an accreting white dwarf evolves quasi-statically are compared with the cooling evolution of a nonaccreting, one solar mass, pure C-12 core. Then, the evolutionary behavior of the white dwarf envelope in mass and temperature, in response to long-term accretion, is used to predict temperatures and luminosities of white dwarfs during quiescent intervals between nova outbursts. It is shown that the observed luminosities and effective temperatures of the bare white dwarfs detected in some cataclysmic variables are the expected intrinsic values associated with classical nova thermonuclear outburst cycles. Two alternate interpretations of their observed surface temperatures and luminosities are assessed.

Sion, E. M.↗
NASA NTRS1974

Molecular column densities in selected model atmospheres

From an examination of predicted column densities, the following conclusions were drawn: (1) The SiO ought to be visible in carbon stars which were generated from triple alpha burning, but absent from carbon stars generated from the CNO bi-cycle. (2) Variation in the observed relative strengths of TiO and ZrO is indicative of real differences in the ratio Ti/Zr. (3) The TiO/ZrO ratio shows a small variation as C/O and effective temperature is changed. (4) Column density of silicon dicarbide (SiC2) is sensitive to abundance, temperature, and gravity; hence all relationships between the strength of SiC2 and other stellar parameters will show appreciable scatter. There is however, a substantial luminosity effect present in the SiC2 column densities. (5) Unexpectedly, SiC2 is anti-correlated with C2. (6) The presence of SiC2 in a carbon star eliminates the possibility of these stars having temperatures greater than or equal to 3000 K, or being produced through the CNO bi-cycle.

Johnson, H. R.↗
NASA NTRS1992

Vapor-liquid equilibrium thermodynamics of N2 + CH4 - Model and Titan applications

A thermodynamic model is presented for vapor-liquid equilibrium in the N2 + CH4 system, which is implicated in calculations of the Titan tropospheric clouds' vapor-liquid equilibrium thermodynamics. This model imposes constraints on the consistency of experimental equilibrium data, and embodies temperature effects by encompassing enthalpy data; it readily calculates the saturation criteria, condensate composition, and latent heat for a given pressure-temperature profile of the Titan atmosphere. The N2 content of condensate is about half of that computed from Raoult's law, and about 30 percent greater than that computed from Henry's law.

Thompson, W. R.↗
NASA NTRS1994

Analysis of Voyager spectra of the beta Cephei star nu Eridani

Voyager 500-1700 A spectrophotometric observations of the beta Cephei star nu Eri are presented and discussed. The Voyager observations were obtained in 1981 and cover six pulsation cycles of the star. These data are supplemented with a set of nine International Ultraviolet Explorer (IUE) SWP high-resolution observations covering one, earlier epoch, pulsation cycle. Light curves are derived from the Voyager data at 1055 and 1425 A. These light curves are found to be consistent in both shape and period with published optical curves. The 1055 A light curve also exhibits a phenomenon not seen in the optical curves: a small but highly significant systematic increase in the flux of the maximum light phases while maintaining a constant minimum light level over the interval of observation. Substantially larger errors in the longer wavelength data preclude discussion of this phenomenon in the 1425 A light curve. Examination of the far-UV continuum in nu Eri during this period shows that the color temperature is lower for the brighter maxima. Analysis of the far-UV continuum at maximum and minimum light yields an effective temperature difference between these two phases of 2200 + or - 750 K. Spectroscopically, three prominent features are seen in the Voyager data: a feature at 985 A mostly due to a blend of C III 977 A, H I Ly gamma 972 A, and N III 990 A; a feature at 1030 A due to H I Ly beta 1026 A and C II 1037 A; and the Si IV resonance doublet near 1400 A. A comparison of the 912-1700 A spectral region in nu Eri with a set of standard, i.e., nonpulsating stars, shows that nu Eri closely resembles the standard both in continuum shape and spectral line strengths with the possible exception of a slight flux excess between 912 and 975 A. The equivalent width of the 985 A feature is shown to vary in strength over the pulsation cycle in antiphase with the light curve and variations seen in the C IV 1548-1551 lines from the IUE data. This behavior of the 985 A feature is most likely caused by variations in the strength of the Ly gamma component of the blend. Comparisons are also made between nu Eri and the only other beta Cephei star studied in the far-UV, BW Vul, with the most notable differences between the two stars being the much larger delta(T(sub eff)) for BW Vul and the almost total absence of abnormalities in observed spectrum of nu Eri.

Porri, A.↗
NASA NTRS1994

Boundary-layer transition detection with infrared imaging emphasizing cryogenic applications

This paper reviews the technique of boundary-layer transition detection using infrared (IR) imaging, emphasizing cryogenic wind-tunnel testing. With the exception of the low-temperature effects on the IR radiation, the discussion is relevant to conventional wind-tunnel and flight testing as well. At low temperatures, IR imaging encounters a reduction in the radiated energy throughout the IR spectrum, combined with a shift to longer wavelengths of the bulk of the radiation. This radiation behavior affects the minimum resolvable temperature difference (MRTD) of the IR imaging system because of its fixed wave band sensitivity. In the absence of commercial long wavelength IR imaging systems, operating at wavelengths longer than 13 micron, some measures can be taken to alleviate the problem caused by the MRTD limitation. The thermal signature of transition can be enhanced by allowing a small and controlled temperature increase of the wind-tunnel flow that induces a transient heat transfer to the model. This action temporarily reveals the model area under the turbulent regime through its higher heating rate compared with the laminar regime. The contrast between the areas exposed to the two regimes can be enhanced by subtraction of thermograms (the equilibrium thermogram from the transient thermogram). Further visual improvement can be obtained through shade stretching or binary shading.

Gartenberg, Ehud↗
NASA NTRS2018

Detection of Photospheric Features in the Near-Infrared Spectrum of a Class 0 Protostar

We present a near-infrared K-band R ≃ 1500 Keck spectrum of S68N, a Class 0 protostar in the Serpens molecular cloud. The spectrum shows a very red continuum, CO absorption bands, weak or non-existent atomic metal absorptions, and H2 emission lines. The near-IR H2 emission is consistent with excitation in shocks or by X-rays but not by UV radiation. We model the absorption component as a stellar photosphere plus circumstellar continuum emission with wavelength-dependent extinction. A Markov Chain Monte Carlo analysis shows that the most likely model parameters are consistent with a low-temperature, low-gravity photosphere with signifi cant extinction and no more than modest continuum veiling. Its T(eff) ≃ 3260 K effective temperature is similar to that of older, more evolved pre-main-sequence stars, but its surface gravity log g ≃ 2:4 cm/sq.s is approximately 1 dex lower. This implies that the radius of this protostar is a factor of ~ 3 larger than that of 106 yr old T Tauri stars. Its low veiling is consistent with a circumstellar disk having intrinsic near-IR emission that is less than or equal to that of more evolved Class I protostars. Along with the high extinction, this suggests that most of the circumstellar material is in a cold envelope, as expected for a Class 0 protostar. This is the first known detection and analysis of a Class 0 protostar absorption spectrum.

Thomas P Greene↗
NASA NTRS2009

Numerical and Physical Modeling of the Response of Resonator Liners to Intense Sound and Grazing Flow

Two significant advances have been made in the application of computational aeroacoustics methodology to acoustic liner technology. The first is that temperature effects for discrete sound are not the same as for broadband noise. For discrete sound, the normalized resistance appears to be insensitive to temperature except at high SPL. However, reactance is lower, significantly lower in absolute value, at high temperature. The second is the numerical investigation the acoustic performance of a liner by direct numerical simulation. Liner impedance is affected by the non-uniformity of the incident sound waves. This identifies the importance of pressure gradient. Preliminary design one and two-dimensional impedance models were developed to design sound absorbing liners in the presence of intense sound and grazing flow. The two-dimensional model offers the potential to empirically determine incident sound pressure face-plate distance from resonator orifices. This represents an important initial step in improving our understanding of how to effectively use the Dean Two-Microphone impedance measurement method.

Hersh, Alan S.↗
NASA NTRS1971

Maximum temperatures for radiation from plasma waves.

Upper limits to radiation temperatures from plasma waves for emissions near the fundamental and second harmonic of the electron plasma frequency are derived in terms of effective temperature for plasma waves. Results are obtained that differ from those of Melrose (1970) by a factor that can exceed 40,000 for some plasmas.

Smith, D. F.↗
NASA NTRS1992

Effects of temperature-dependent molecular absorption coefficients on the thermal infrared remote sensing of the earth surface

The effect of temperature-dependent molecular absorption coefficients on thermal infrared spectral signatures measured from satellite sensors is investigated by comparing results from the atmospheric transmission and radiance codes LOWTRAN and MODTRAN and the accurate multiple scattering radiative transfer model ATRAD for different atmospheric profiles. The sensors considered include the operational NOAA AVHRR and two research instruments planned for NASA's Earth Observing System (EOS): MODIS-N (Moderate Resolution Imaging Spectrometer-Nadir-Mode) and ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer). The difference in band transmittance is as large as 6 percent for some thermal bands within atmospheric windows and more than 30 percent near the edges of these atmospheric windows. The effect of temperature-dependent molecular absorption coefficients on satellite measurements of sea-surface temperature can exceed 0.6 K. Quantitative comparison and factor analysis indicate that more accurate measurements of molecular absorption coefficients and better radiative transfer simulation methods are needed to achieve SST accuracy of 0.3 K, as required for global numerical models of climate, and to develop land-surface temperature algorithms at the 1-K accuracy level.

Wan, Zhengming↗
NASA NTRS1984

Time dependent land and vegetation canopy temperatures

A simple interactive biosphere is presented based on an electrical analog of turbulent transport processes that produce heat and moisture fluxes between land and the atmosphere. A network of resistances that effect temperature or vapor pressure fluxes are identified and entered into the quasi steady state equations. A set of solutions that depict a realistic diurnal cycle is included.

Sud, Y. C.↗
NASA NTRS1982

Neutron star envelopes

It is pointed out that the separate study of neutron star envelopes is a valuable technique for gaining insights into neutron star cooling calculations. It is shown that, to an excellent approximation, the temperature at the inner boundary of the envelope, T sub b, is a function only of T sub s to the 4th power over g sub s, where T sub s is the effective temperature and g sub s is the surface gravity. This result makes it possible to investigate very simply the effects of general relativity and of opacity changes on the T sub b - T sub s relation and to compare calculations by different workers, even though they use different neutron star models. It is also shown that the most important opacity source for obtaining a reliable T sub b - T sub s relation is the conductive opacity of matter when the ions are liquid. Calculations are presented in which particular attention is given to this region and the best available opacities are used.

Gudmundsson, E. H.↗
NASA NTRS1983

Microstructure and surface chemistry of amorphous alloys important to their friction and wear behavior

An investigation was conducted to examine the microstructure and surface chemistry of amorphous alloys, and their effects on tribological behavior. The results indicate that the surface oxide layers present on amorphous alloys are effective in providing low friction and a protective film against wear in air. Clustering and crystallization in amorphous alloys can be enhanced as a result of plastic flow during the sliding process at a low sliding velocity, at room temperature. Clusters or crystallines with sizes to 150 nm and a diffused honeycomb-shaped structure are produced on the wear surface. Temperature effects lead to drastic changes in surface chemistry and friction behavior of the alloys at temperatures to 750 C. Contaminants can come from the bulk of the alloys to the surface upon heating and impart to the surface oxides at 350 C and boron nitride above 500 C. The oxides increase friction while the boron nitride reduces friction drastically in vacuum.

Miyoshi, K.↗
NASA NTRS1986

Microstructure and surface chemistry of amorphous alloys important to their friction and wear behavior

An investigation was conducted to examine the microstructure and surface chemistry of amorphous alloys, and their effects on tribological behavior. The results indicate that the surface oxide layers present on amorphous alloys are effective in providing low friction and a protective film against wear in air. Clustering and crystallization in amorphous alloys can be enhanced as a result of plastic flow during the sliding process at a low sliding velocity, at room temperature. Clusters or crystallines with sizes to 150 nm and a diffused honeycomb-shaped structure are produced on sizes to 150 nm and a diffused honeycomb-shaped structure are produced on the wear surface. Temperature effects lead to drastic changes in surface chemistry and friction behavior of the alloys at temperatures to 750 C. Contaminants can come from the bulk of the alloys to the surface upon heating and impart to the surface oxides at 350 C and boron nitride above 500 C. The oxides increase friction while the boron nitride reduces friction drastically in vacuum.

Miyoshi, K.↗