Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Advanced oxygen-hydrocarbon rocket engine study

This study identifies and evaluates promising LO2/HC rocket engine cycles, produces a consistent and reliable data base for vehicle optimization and design studies, demonstrates the significance of propulsion system improvements, and selects the critical technology areas necessary to realize an improved surface to orbit transportation system. Parametric LO2/HC engine data were generated over a range of thrust levels from 890 to 6672 kN (200K to 1.5M 1bF) and chamber pressures from 6890 to 34500 kN (1000 to 5000 psia). Engine coolants included RP-1, refined RP-1, LCH4, LC3H8, LO2, and LH2. LO2/RP-1 G.G. cycles were found to be not acceptable for advanced engines. The highest performing LO2/RP-1 staged combustion engine cycle utilizes LO2 as the coolant and incorporates an oxidizer rich preburner. The highest performing cycle for LO2/LCH4 and LO2/LC3H8 utilizes fuel cooling and incorporates both fuel and oxidizer rich preburners. LO2/HC engine cycles permitting the use of a third fluid LH2 coolant and an LH2 rich gas generator provide higher performance at significantly lower pump discharge pressures. The LO2/HC dual throat engine, because of its high altitude performance, delivers the highest payload for the vehicle configuration that was investigated.

Obrien, C. J.↗
NASA NTRS1975

Aerodynamic analysis of several high throat Mach number inlets for the quiet clean short-haul experimental engine

The results of an analytical study to investigate internal and external surface Mach numbers on several inlet geometries for possible application to the nacelle of the Quiet Clean Short-Haul Experimental Engine (QCSEE) are presented. The effects of external forebody geometry and internal lip geometry were illustrated at both low-speed and cruise conditions. Boundary-layer analyses were performed on several geometries to determine if lip flow separation might exist. The results indicated that inner-surface Mach number level and gradient could be reduced with inlets at a 50 deg incidence angle by blunting the external forebody geometry. The external Mach numbers at cruise conditions indicated that a compromise in the external forebody bluntness might be required to satisfy both low-speed and cruise conditions. For a fixed value of bluntness parameter, no lip flow separation was indicated for the 1.46- and 1.57-area-contraction-ratio inlets at low-speed conditions. However, a lip separation condition was obtained with the 1.37-contraction-ratio inlet. The QCSEE nacelle design takeoff operating condition (incidence angle of 50 deg and free-stream Mach number of 0.12) resulted in higher peak surface Mach numbers than the design crosswind (incidence angle of 90 deg and free-stream Mach number of 0.05) or static condition.

Albers, J. A.↗
NASA NTRS2017

Connecting Projects to Complete the In Situ Resource Utilization Paradigm

Terrain Identify specifics such as slope, rockiness, traction parameters Identify what part of ISRU needs each Physical Geotechnical Hardness, density, cohesion, etc. Identify what part of ISRU needs each (e.g., excavation needs to know hardness, density; soil processing needs to know density, cohesion; etc.)Mineral Identify specifics Identify what part of ISRU needs each Volatile Identify specifics Identify what part of ISRU needs each Atmosphere Identify specifics Identify what part of ISRU needs each Environment Identify specifics Identify what part of ISRU needs each Resource Characterization What: Develop an instrument suite to locate and evaluate the physical, mineral, and volatile resources at the lunar poles Neutron Spectrometer Near Infrared (IR) to locate subsurface hydrogen surface water Near IR for mineral identification Auger drill for sample removal down to 1 m Oven with Gas Chromatograph Mass Spectrometer to quantify volatiles present ISRU relevance: Water volatile resource characterization and subsurface material access removal Site Evaluation Resource Mapping What: Develop and utilize new data products and tools for evaluating potential exploration sites for selection and overlay mission data to map terrain, environment, and resource information e.g., New techniques applied to generate Digital Elevation Map (DEMs) at native scale of images (1mpxl)ISRU relevance: Resource mapping and estimation with terrain and environment information is needed for extraction planning Mission Planning and Operations What: Develop and utilize tools and procedures for planning mission operations and real time changes Planning tools include detailed engineering models (e.g., power and data) of surface segment systems allows evaluation of designs ISRU relevance: Allows for iterative engineering as a function of environment and hardware performance.

Paradigm↗
NASA NTRS2023

Influences of Varied Electrical Discharge Machining Operations on Surface Conditions of Several Nickel-Based Superalloys

Nickel-based superalloys designed for use in gas turbine engines blades are difficult and expensive to properly machine without undue surface damage, due in part to their superior mechanical properties at high temperatures. Numerically controlled electrical discharge machining (EDM) has progressed to commonly be used as a machining process for initial sectioning, detailed roughing, and even some finishing operations. The objective of this study was to examine the effect of EDM on resulting surface conditions of superalloy 718 after slicing using typical rough, semi-finish, and finish condition sets with a typical wire EDM machine. Surface roughness, residual stress, and microstructures were compared for these conditions. The varied EDM conditions influenced surface roughness as intended. The residual stresses and surface roughness directly corresponding to the EDM steps were determined. While roughness decreased when progressing from rough to finish EDM conditions, tensile residual stresses unexpectedly increased. Brief assessments after EDM of two higher performance powder metallurgy disk superalloys ME209 and LSHR indicated this inverse relationship of roughness versus tensile residual stress was also present for these superalloys, where tensile residual stresses were significantly enhanced.

superalloys↗
NASA NTRS2014

A Systems Engineering Approach to Quality Assurance for Aerospace Testing

On the surface, it appears that AS9100 has little to say about how to apply a Quality Management System (QMS) to major aerospace test programs (or even smaller ones). It also appears that there is little in the quality engineering Body of Knowledge (BOK) that applies to testing, unless it is nondestructive examination (NDE), or some type of lab or bench testing associated with the manufacturing process. However, if one examines: a) how the systems engineering (SE) processes are implemented throughout a test program; and b) how these SE processes can be mapped to the requirements of AS9100, a number of areas for involvement of the quality professional are revealed. What often happens is that quality assurance during a test program is limited to inspections of the test article; what could be considered a manufacturing al fresco approach. This limits the quality professional and is a disservice to the programs and projects, since there are a number of ways that quality can enhance critical processes, and support efforts to improve risk reduction, efficiency and effectiveness. The Systems Engineering (SE) discipline is widely used in aerospace to ensure the progress from Stakeholder Expectations (the President, Congress, the taxpayers) to a successful, delivered product or service. Although this is well known, what is not well known is that these same SE processes are implemented in varying complexity, to prepare for and implement test projects that support research, development, verification and validation, qualification, and acceptance test projects. Although the test organization's terminology may vary from the SE terminology, and from one test service provider to another, the basic process is followed by successful, reliable testing organizations. For this analysis, NASA Procedural Requirements (NPR) 7123.1, NASA Systems Engineering Processes and Requirements is used to illustrate the SE processes that are used for major aerospace testing. Many of these processes are also implemented for smaller test projects, and this set of processes will also look familiar to those who have participated in launch site activation and flight demonstrations.

Shepherd, Christena C.↗
NASA NTRS2015

A Systems Engineering Approach to Quality Assurance for Aerospace Testing

On the surface, it appears that AS91001 has little to say about how to apply a Quality Management System (QMS) to major aerospace test programs (or even smaller ones). It also appears that there is little in the quality engineering Body of Knowledge (BOK)2 that applies to testing, unless it is nondestructive examination (NDE), or some type of lab or bench testing associated with the manufacturing process. However, if one examines: a) how the systems engineering (SE) processes are implemented throughout a test program; and b) how these SE processes can be mapped to the requirements of AS9100, a number of areas for involvement of the quality professional are revealed. What often happens is that quality assurance during a test program is limited to inspections of the test article; what could be considered a manufacturing al fresco approach. This limits the quality professional and is a disservice to the programs and projects, since there are a number of ways that quality can enhance critical processes, and support efforts to improve risk reduction, efficiency and effectiveness.

Shepherd, Christena C.↗
NASA NTRS1994

A Full Navier-Stokes Analysis of Subsonic Diffuser of a Bifurcated 70/30 Supersonic Inlet for High Speed Civil Transport Application

A full Navier-Stokes analysis was performed to evaluate the performance of the subsonic diffuser of a NASA Lewis Research Center 70/30 mixed-compression bifurcated supersonic inlet for high speed civil transport application. The PARC3D code was used in the present study. The computations were also performed when approximately 2.5 percent of the engine mass flow was allowed to bypass through the engine bypass doors. The computational results were compared with the available experimental data which consisted of detailed Mach number and total pressure distribution along the entire length of the subsonic diffuser. The total pressure recovery, flow distortion, and crossflow velocity at the engine face were also calculated. The computed surface ramp and cowl pressure distributions were compared with experiments. Overall, the computational results compared well with experimental data. The present CFD analysis demonstrated that the bypass flow improves the total pressure recovery and lessens flow distortions at the engine face.

Kapoor, Kamlesh↗
NASA NTRS1951

NACA Investigations of Icing-Protection Systems for Turbojet-Engine Installations

Investigations have been made in flight and in wind tunnels to determine which components of turbojet installations are most critical in icing conditions, and to evaluate several methods of icing protection. From these studies, the requirements necessary for adequate icing protection and the consequent penalties on engine performance can be estimated. Because investigations have indicated that the compressor-inlet screen constitutes the greatest icing hazard and is difficult to protect, complete removal or retraction of the screen upon encountering an icing condition is recommended. In the absence of the screen, the inlet guide vanes of an axial-flow-type turbojet engine constitute the greatest danger to engine operation in an icing condition; a centrifugal-type engine, on the other hand, is relatively unsusceptible to icing once the screen has been removed. Of the three icing-protection systems investigated, surface heating, hot-gas bleedback, and inertia-separation inlets, only the first two offer an acceptable solution to the problem of engine icing protection. Surface heating, either by gas heating or electrical means, appears to be the most acceptable icing-protection method with regard to performance losses. Hot-gas bleedback, although causing undesirable thrust losses, offers an easy means of obtaining icing protection for some installations. The final choice of an icing-protection system depends, however, on the supply of heated gas and electrical power available and on the allowable performance and. weight penalties associated with each system.

VonGlahn, Uwe↗
NASA NTRS1954

Exploratory Engine Test of Transpiration-cooled Turbine-rotor Blade with Wire-cloth Shell

Engine tests were made on a transpiration-cooled blade that was fabricated from an internal load-carrying member with an external surface of wire cloth. After operation in the engine, some damage was noted at the tip region of the trailing edge of the blades. On other sections of the blade, the wire cloth did not appear greatly overheated, and it appeared that satisfactory chordwise temperature distribution was provided by orifices in the blade base.

ENGINES, COOLING↗
NASA NTRS1987

Effect of water on hydrogen permeability

Doping of hydrogen with CO and CO2 was developed to reduce hydrogen permeation in Stirling engines by forming a low permeability oxide coating on the inner surface of the heater head tubes. Although doping worked well, under certain circumstances the protective oxide could be chemically reduced by the hydrogen in the engine. Some oxygen is required in the hydrogen to prevent reduction. Eventually, all the oxygen in the hydrogen gas - whatever its source - shows up as water. This is the result of hydrogen reducing the CO, CO2, or the protective inner surface oxides. This water can condense in the engine system under the right conditions. If the concentration of water vapor is reduced to a low enough level, the hydrogen can chemically reduce the oxide coating, resulting in an increase in permeability. This work was done to define the minimum water content required to avoid this reduction in the oxide coating. The results of this testing show that a minimum of approximately 750 ppm water is required to prevent an increase in permeability of CG-27, a high temperature metal alloy selected for Stirling engine heater tubes.

Hulligan, David↗
NASA NTRS1979

Transonic aerodynamic characteristics of a supersonic cruise aircraft research model with the engines suspended above the wing

The influence of upper-surface nacelle exhaust flow on the aerodynamic characteristics of a supersonic cruise aircraft research configuration was investigated in a 16 foot transonic tunnel over a range of Mach numbers from 0.60 to 1.20. The arrow-wing transport configuration with engines suspended over the wing was tested at angles of attack from -4 deg to 6 deg and jet total pressure ratios from 1 to approximately 13. Wing-tip leading edge flap deflections of -10 deg to 10 deg were tested with the wing-body configuration. Various nacelle locations (chordwise, spanwise, and vertical) were tested over the ranges of Mach numbers, angles of attack, and jet total-pressure ratios. The results show that reflecting the wing-tip leading edge flap from 0 deg to -10 deg increased the maximum lift-drag ratio by 1.0 at subsonic speeds. Jet exhaust interference effects were negligible.

Mercer, C. E.↗
NASA NTRS2005

STS-114: Discovery Mission Status Briefing

Phil Engelauf, STS-114 Mission Operations Representative reports: the orbital rendezvous was successful, and today's activities includes initial preparations of the next day's extravehicular activities (EVA); he specifically mentioned tile repair, wiring on the outside of the vehicle to try to recover CMG2 (Control Moment Gyro), and preparation for the external stowage platform. John Shannon, Manager of the Space Shuttle Operations and Integration reports from Engineering standpoint that the composites of the underside of the tile surface seen from pictures taken during the pitch maneuver were extremely clean; the Engineering staff continues to look at the focus inspection data from the orbital boom sensor system (OBSS) and other data to assess the condition of the vehicle. Solid rocket boosters were retrieved and are towed back to the Air Force hangar in Cape Carneval. Six target inspection (nose gear doors, gap fillers, chine area, external tank doors, trailing edge, and ice), and arm operations, foam, conservation measures, shuttle air lock, aerodynamics assessment and re-entry were topics covered with the News media.

Source record↗
NASA NTRS1971

Flight investigation of airframe installation effects on an auxiliary inlet ejector nozzle on an underwing engine nacelle

The local flow field approaching an installed nozzle may vary from isolated test conditions, thereby affecting exhausting nozzle performance. An installation of general interest is a podded engine mounted near the aft lower surface of the wing. The effect of this installation on the performance of an auxiliary inlet ejector nozzle was investigated over a Mach number range of 0.7 to 1.3 by using a modified F-106B aircraft. Both floating and fixed-open door configurations were examined. The ejector nozzle trailing-edge flaps were simulated in the closed position with rigid structure which provided a boattail angle of 15 deg. Primary nozzle area was varied as exhaust gas temperature was varied between 982.2 and 2003.3 K.

Burley, R. R.↗
NASA NTRS1972

Flight investigation of an underwing nacelle installation of an auxiliary-inlet ejector nozzle with a clamshell flow diverter from Mach 0.6 to 1.3

A nozzle installation of general interest is a podded engine mounted near the aft lower surface of the wing. The effect of this installation on the performance of an auxiliary-inlet ejector nozzle with a clamshell flow diverter was investigated over a Mach number range of 0.6 to 1.3 by using a modified F-106B aircraft. The clamshell flow diverter was tested in a 17 deg position with double-hinged synchronized floating doors. The ejector nozzle trailing-edge flaps were simulated in the closed position with a rigid structure which provided a boattail angle of 10 deg. Primary nozzle area was varied as exhaust gas temperature was varied between 975 and 1561 K. With the nozzle in a subsonic cruise position, the nozzle gross thrust coefficient was 0.918 at a flight Mach number of 0.9.

Head, V. L.↗
NASA NTRS1973

The cylindrical electrostatic probes for Atmosphere Explorer -C, -D, and -E.

This paper briefly describes the cylindrical electrostatic probes to be used on the new Atmosphere Explorer-C, -D, and -E, and outlines the methods to be employed to analyze the experimental data in terms of electron temperature and ion and electron concentration. Two independent cylindrical sensors and partially redundant electronic systems permit greater reliability in measurements. Measurements are made at 1-sec and 2-sec intervals along the orbit. The sensors themselves have been modified from previous applications to cope with the lower electron temperature expected in these low-altitude orbits and to counter possible surface contamination caused by the hydrazine engines used for orbit adjustments.

Brace, L. H.↗