Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Effects of Surface Treatments on Secondary Electron Emission from CVD Diamond Films

Secondary electron emission (SEE) properties of polycrystalline diamond films grown by chemical vapor deposition (CVD) were measured. The total secondary yield (sigma) from as-grown samples was observed to be as high as 20 at room temperature and 48 while heating at 700 K in vacuum. Electron-beam-activated, alkali-terminated diamond films have shown stable values of sigma as high as 60 when coated with CsI and similarly high values when coated with other alkali halides. Diamond coated with BaF2 had a stable sigma of 6, but no enhancement of the SEE properties was observed with coatings of Ti or Au. Hydrogen was identified to give rise to this effect in as-grown films. However, electron beam exposure led to a reduction in sigma values as low as 2. Exposure to a molecular hydrogen environment restored sigma to its original value after degradation, and enabled stable secondary emission during electron beam exposure. Atomic hydrogen and hydrogen plasma treatments were performed on diamond/Mo samples in an attempt to increase the near-surface hydrogen concentration which might lead to increased stability in the secondary emission. Raman scattering analysis, scanning electron microscopy, and Auger electron spectroscopy (AES) confirmed that hydrogen plasma and atomic hydrogen treatments improved the quality of the CVD diamond significantly. Elastic recoil detection (ERD) showed that heating as-grown diamond targets to 7OO K, which was correlated with an increase in sigma, removed contaminants from the surface but did not drive hydrogen from the diamond bulk. ERD showed that the hydrogen plasma treatment produced an increase in the hydrogen concentration in the near-surface region which did not decrease while heating in vacuum at 700 K, but no improvement in the SEE properties was observed.

Mearini, G. T.↗

Effective Crewed Surface Science near the Lunar South Pole: Some Illumination Considerations

Exploration near the lunar South Pole has substantial scientific promise for expanding our understanding of the Moon beyond what has been accomplished by Apollo and other lunar missions. An obvious difference from the Apollo experience is that the polar location for Artemis will guarantee the Sun is going to be low above the horizon. A great deal of excellent work has been, and is being, done on the availability of light (“yes/no”) for exploration purposes [e.g., 1-4]. However, we raise the additional consideration of the qualitative effects of low solar elevation on crew traverses, crew observations, and other science measurements [see also 5, though ground rules of that study presumed higher Sun]. We emphasize that our view is that these issues are unlikely to be mission objective-threatening, particularly if adequately considered in advance.

C. I. Fassett↗

Aerosol Direct Radiative and Cloud Adjustment Effects on Surface Climate over Eastern China: Analyses of WRF Model Simulations

The WRF-simulated changes in clouds and climate due to the increased anthropogenic aerosols for the summers of 2002–08 (vs the 1970s) over eastern China were used to offline calculate the radiative forcings associated with aerosol–radiation (AR) and aerosol–cloud–radiation (ACR) interactions, which subsequently facilitated the interpretation of surface temperature changes. During this period, the increases of aerosol optical depth (ΔAOD) averaged over eastern China range from 0.18 in 2004 to 0.26 in 2007 as compared to corresponding cases in the 1970s, and the multiyear means (standard deviations) of AR and ACR forcings at the surface are −6.7 (0.58) and −3.5 (0.63) W m −2 , respectively, indicating the importance of cloud changes in affecting both the aerosol climate forcing and its interannual variation. The simulated mean surface cooling is 0.35°C, dominated by AR and ACR with a positive (cooling) feedback associated with changes in meteorology (~10%), and two negative (warming) feedbacks associated with decreases in latent (~70%) and sensible (~20%) heat fluxes. More detailed spatial characteristics were analyzed using ensemble simulations for the year 2008. Three regions—Jing-Jin-Ji (ΔAOD ~ 0.63), Sichuan basin (ΔAOD ~ 0.31), and middle Yangtze River valley (ΔAOD ~ 0.26)—at different climate regimes were selected to investigate the relative roles of AR and ACR. While the AR forcing is closely related to ΔAOD values, the ACR forcing presents different regional characteristics owing to cloud changes. In addition, the surface heat flux feedbacks are also different between regions. The study thus illustrates that ACR forcing is useful as a diagnostic parameter to unravel the complexity of climate change to aerosol forcing over eastern China.

54 ENVIRONMENTAL SCIENCES↗

Modeling of induced seismicity and ground vibrations associated with geologic CO 2 storage, and assessing their effects on surface structures and human perception

In this paper, we present model simulations of ground motions caused by CO 2 -injection-induced fault reactivation and analyze the results in terms of the potential for damage to ground surface structures and nuisance to the local human population. It is an integrated analysis from cause to consequence, including the whole chain of processes starting from earthquake inception in the subsurface, wave propagation toward the ground surface, and assessment of the consequences of ground vibration. For a small magnitude (M w =3) event at a hypocenter depth of about 1000m, we first used the simulated ground-motion wave train in an inverse analysis to estimate source parameters (moment magnitude, rupture dimensions and stress drop), achieving good agreement and thereby verifying the modeling of the chain of processes from earthquake inception to ground vibration. We then analyzed the ground vibration results in terms of peak ground acceleration (PGA), peak ground velocity (PGV) and frequency content, with comparison to U.S. Geological Survey's instrumental intensity scales for earthquakes and the U.S. Bureau of Mines' vibration criteria for cosmetic damage to buildings, as well as human-perception vibration limits. Our results confirm the appropriateness of using PGV (rather than PGA) and frequency for the evaluation of potential ground-vibration effects on structures and humans from shallow injection-induced seismic events. For the considered synthetic M w =3 event, our analysis showed that the short duration, high frequency ground motion may not cause any significant damage to surface structures, but would certainly be felt by the local population.

54 ENVIRONMENTAL SCIENCES↗

Bounds on the Rate-Dependent Plastic Flow of Tantalum up to 75 GPa

In this study we report on the continued development of thermodynamics-based analysis of shock waves propagation with the objective of extracting information related to materials strength at high strain rates and pressures. Building on previous results reported for peak stresses of 10 GPa and 25 GPa, we present a series of three-step gas-gun shock experiments designed to explore the pressure and strain rate dependence of plastic flow in polycrystalline tantalum. These experiments at nominal peak stresses of 50 GPa and 75 GPa show the irreversible deformation before pullback to be almost entirely confined to the shock loading, with negligible plastic relaxation on the post-shock plateau. We also add a reverse-ballistics shot at 25 GPa, which was designed to reveal the pullback response with negligible interference from free-surface effects. General thermodynamic considerations allow us to place bounds on the plastic behavior even for parts of the curve that change far too rapidly for the velocimetric time resolution of (conservatively) ~ 5 ns. To analyze the data, we found it necessary to substantially improve the interpolation/extrapolation scheme in order to improve its robustness, flexibility and range of applicability. We describe the new scheme based on splines, as well as an extension of free-surface corrections to the post-shock rarefaction waves. Reanalysis with the new scheme produces results essentially within the error bars previously reported, showing that the known systematic errors associated with free-surface effects are relatively inconsequential for determining thermodynamic paths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Surface Oxygen Containing Groups on the Catalytic Activity of Multi-walled Carbon Nanotube Supported Pt Catalyst

Multi-walled carbon nanotubes (MWNT) supported platinum catalysts were employed to study the support functionalization on their catalytic performances. The MWNT were subjected to HNO{sub 3} functionalization, in which oxygen-containing-groups (OCGs) were introduced to improve Pt dispersion. The MWNT supports were characterized by nitrogen physisorption and NEXAFS, and the Pt supported on differently functionalized MWNT characterized by X-ray absorption, TEM and both hydrogen and CO chemisorption. Compared to the as received MWNT supports, Pt dispersion is improved on the HNO3 treated MWNT supports, but the turnover frequency (TOF) of aqueous phase reforming decreases by half. The TOF can be recovered by removing the OCGs via high temperature annealing. To further investigate the OCGs effect, different probe reactions, including both steam reforming and liquid phase reforming of hydrocarbon oxygenates and dehydrogenation of alkanes in the liquid and gas phases, have been performed on the MWNT supported catalysts with different OCGs. A comparison of these reaction results suggests that OCGs are only detrimental to reactions in a binary mixture with two components of different hydrophilicity due to their competitive adsorption on the catalyst supports.

08 HYDROGEN↗

Covalent Surface Modification Effects on Single‐Walled Carbon Nanotubes for Targeted Sensing and Optical Imaging

Abstract Optical nanoscale technologies often implement covalent or noncovalent strategies for the modification of nanoparticles, whereby both functionalizations are leveraged for multimodal applications but can affect the intrinsic fluorescence of nanoparticles. Specifically, single‐walled carbon nanotubes (SWCNTs) can enable real‐time imaging and cellular delivery; however, the introduction of covalent SWCNT sidewall functionalizations often attenuates SWCNT fluorescence. Recent advances in SWCNT covalent functionalization chemistries preserve the SWCNT's pristine graphitic lattice and intrinsic fluorescence, and here, such covalently functionalized SWCNTs maintain intrinsic fluorescence‐based molecular recognition of neurotransmitter and protein analytes. The covalently modified SWCNT nanosensor preserves its fluorescence response towards its analyte for certain nanosensors, presumably dependent on the intermolecular interactions between SWCNTs or the steric hindrance introduced by the covalent functionalization that hinders noncovalent interactions with the SWCNT surface. These SWCNT nanosensors are further functionalized via their covalent handles with a targeting ligand, biotin, to self‐assemble on passivated microscopy slides, and these dual‐functionalized SWCNT materials are explored for future use in multiplexed sensing and imaging applications.

Chio, Linda↗

Spurious phenomena occurring during current measurement on ultra-thin dielectric layers: From electro-thermal effects to surface damage

In this paper, the conduction properties of dielectric ultra-thin layers are studied using atomic force microscopy. Especially, the conductive-atomic force microscope allows to measure the leakage current at the nanoscale and to study the degradation mechanisms locally. Nonetheless, the dielectric layer seems to be damaged by a technique's specific phenomenon: hillocks appear when a positive tip bias is applied on different dielectrics. In this paper, the formation of these hillocks is studied. Contrary to what is observed during the dielectric breakdown, the conductivity is reduced after hillocks formation which occurs after the dielectric breakdown. Moreover, we have observed the formation of cavities in the silicon substrate linked to the formation of hillocks, which is not compatible with a swelling process (as dielectric breakdown induced epitaxy). We propose that these results may be explained by an electro-thermal effect due to the large dissipated energy, maybe combined with the oxidation of the substrate. Finally, the interdependence of measurements is demonstrated during serial acquisition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The effect of surface brightness dimming in the selection of high-z galaxies

Cosmological surface brightness (SB) dimming of the form (1 + z){sup –4} affects all sources. The strong dependence of SB dimming on redshift z suggests the presence of a selection bias when searching for high-z galaxies, i.e., we tend to detect only those galaxies with a high SB. However, unresolved knots of emission are not affected by SB dimming, thus providing a way to test the clumpiness of high-z galaxies. Our strategy relies on the comparison of the total flux detected for the same source in surveys characterized by different depth. For all galaxies, deeper images permit the better investigation of low-SB features. Cosmological SB dimming makes these low-SB features hard to detect when going to higher and higher redshifts. We used the GOODS and HUDF Hubble Space Telescope legacy data sets to study the effect of SB dimming on low-SB features of high-z galaxies and compare it to the prediction for smooth sources. We selected a sample of Lyman-break galaxies at z ∼ 4 (i.e., B {sub 435}-band dropouts) detected in all of the data sets and found no significant trend when comparing the total magnitudes measured from images with different depth. Through Monte Carlo simulations we derived the expected trend for galaxies with different SB profiles. The comparison to the data hints at a compact distribution for most of the rest-frame ultraviolet light emitted from high-z galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗

Effects of surface roughness on the aerodynamic characteristics of the modified 089 B shuttle orbiter at Mach 6 (LA15)

A one hundredth scale model of the modified 089B shuttle orbiter was tested in the Langley 20-Inch Mach 6 tunnel. Force and moment, surface pressure and oilflow data were obtained on one model, and phase-change coating data were obtained on another. The pressure tests were conducted first; the tubes were clipped near the base of the model and then the force and moment and oil flow tests conducted. Angles of attack for the tests were from 20 deg to 35 deg and are commensurate with the range of flight values from entry down to Mach 5. The design flight Reynolds number at Mach 6, based on model length, was 15 million, which could not be obtained in the tunnel; therefore, the tests were conducted at the highest and lowest values for this model in the tunnel, 9.4 million and 4.0 million, respectively, to indicate Reynolds number effects. Two control deflection combinations, representative of the bank and pitch control limits of the design flight trajectory, were used.

Ashby, G. C., Jr.↗

Effect of Surface Roughness on Wind Turbine Performance

Wind farm operators observe production deficits as machines age. Quantifying deterioration on individual components is difficult, but one potential explanation is accumulation of blade surface roughness. Historically, wind turbine airfoils were designed for lift to be insensitive to roughness by simulating roughness with trip strips. However, roughness was still shown to negatively affect performance. Furthermore, experiments illustrated distributed roughness is not properly simulated by trip strips. To understand how real-world roughness affects performance, field measurements of turbine-blade roughness were made and simulated on a NACA 63 3 -418 airfoil in a wind tunnel. Insect roughness and paint chips were characterized and recreated as distributed roughness and a forward-facing step. Distributed roughness was tested in three heights and five density configurations. The model chord Reynolds number was varied between 0.8 to 4.8 x 10 6 . Measurements of lift, drag, pitching moment, and boundary-layer transition were completed. Results indicate minimal effect from paint-chip roughness. As distributed roughness height and density increase, lift-curve slope, maximum lift, and lift-to-drag ratio decrease. As Reynolds number increases, bypass transition occurs earlier. The critical roughness Reynolds number varies between 178 to 318, within the historical range. Little sensitivity to pressure gradient is observed. At a chord Reynolds number of 3.2 x 10 6 , the maximum lift-to-drag ratio decreases 40% for 140 m roughness, corresponding to a 2.3% loss in annual energy production. Simulated performance loss compares well to measured performance loss on an in-service wind turbine.

17 WIND ENERGY↗

The Effects of Surfaces on the Aerodynamics and Acoustics of Jet Flows

Aircraft noise mitigation is an ongoing challenge for the aeronautics research community. In response to this challenge, low-noise aircraft concepts have been developed that exhibit situations where the jet exhaust interacts with an airframe surface. Jet flows interacting with nearby surfaces manifest a complex behavior in which acoustic and aerodynamic characteristics are altered. In this paper, the variation of the aerodynamics, acoustic source, and far-field acoustic intensity are examined as a large at plate is positioned relative to the nozzle exit. Steady Reynolds-Averaged Navier-Stokes solutions are examined to study the aerodynamic changes in the field-variables and turbulence statistics. The mixing noise model of Tam and Auriault is used to predict the noise produced by the jet. To validate both the aerodynamic and the noise prediction models, results are compared with Particle Image Velocimetry (PIV) and free-field acoustic data respectively. The variation of the aerodynamic quantities and noise source are examined by comparing predictions from various jet and at plate configurations with an isolated jet. To quantify the propulsion airframe aeroacoustic installation effects on the aerodynamic noise source, a non-dimensional number is formed that contains the flow-conditions and airframe installation parameters.

Smith, Matthew J.↗

Surface film effects on drop tube undercooling studies

The effects of various gaseous atmospheric constituents on drop-tube solidified samples of elemental metals were examined from a microstructural standpoint. All specimens were prepared from the purest available elements, so effects of impurities should not account for the observed effects. The drop-tube gas has a definite effect on the sample microstructure. Most dramatically, the sample cooling rate is effected. Some samples receive sufficient cooling to solidify in free fall while others do not, splating at the end of the drop tube in the sample catcher. Gases are selectively absorbed into the sample. Upon solidification gas can become less soluble and as a result forms voids within the sample. The general oxidation/reduction characteristics of the gas also affect sample microstructures. In general, under the more favorable experimental conditions including reducing atmospheric conditions and superheatings, examination of sample microstructures indicates that nucleation has been suppressed. This is indicated by underlying uniform dendrite spacings throughout the sample and with a single dendrite orientation through most of the sample. The samples were annealed yielding a few large grains and single or bi-crystal samples were commonly formed. This was especially true of samples that were inadvertently greatly superheated. This is in contrast with results from a previous study in which surface oxides were stable and contained numerous sites of nucleation. The number of nucleation events depends upon the surface state of the specimen as determined by the atmosphere and is consistent with theoretical expectations based upon the thermodynamic stability of surface oxide films. Oxide-free specimens are characterized by shiny surfaces, with no observable features under the scanning electron microscope at 5000X.

Ethridge, E. C.↗

Sensitivity of the superconducting state and magnetic susceptibility to key aspects of electronic structure in ferropnictides

Experiments on the iron–pnictide superconductors appear to show some materials where the ground state is fully gapped, and others where low-energy excitations dominate, possibly indicative of gap nodes. Within the framework of a five-orbital spin fluctuation theory for these systems, we discuss how changes in the doping, the electronic structure or interaction parameters can tune the system from a fully gapped to a nodal sign-changing gap with s-wave (A 1g ) symmetry (s ± ). In particular, we focus on the role of the hole pocket at the (π, π) point of the unfolded Brillouin zone, identified as crucial to the pairing and show that its presence leads to additional nesting of hole and electron pockets, which stabilizes the isotropic s ± state. The pocket's contribution to the pairing can be tuned by doping, surface effects and by changes in interaction parameters, which we examine. Analytic expressions for orbital pairing vertices calculated within the random phase approximation (RPA) fluctuation exchange approximation allow us to draw connections between aspects of the electronic structure, interaction parameters and the form of the superconducting gap.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Surface Temperature on the Distribution and Reactivity of Rh Active Sites for CO Oxidation

Single–atom catalysts are a fast–emerging area in which late–transition metal atoms are supported on oxides, metals, and carbonaceous supports. They show great promise for selective chemical reactions due to their well–defined active sites, and significantly reduce precious metal loading. However, oxide–supported single–atom catalysts have drawbacks such as deactivation due to sintering, and there are on–going debates about the exact nature of the active sites. Herein we report a model system where the surface temperature during Rh deposition on a copper oxide support dictates the Rh size distribution. Here our temperature–programmed desorption experiments reveal that Rh clusters perform CO oxidation at lower temperature than single atoms, and isotopic labelling demonstrates differences in the mechanism in that the C–O bond is broken and reformed on clusters, as opposed to a pure Mars van Krevelen mechanism for CO oxidation at the single–atom Rh sites. We further examine the cluster size distributions with scanning tunneling microscopy and X–ray photoelectron spectroscopy which confirm the presence of both clusters and single atoms for the lower temperature deposition and only single atoms for the higher temperature deposition. Together, these results provide a fundamental understanding of the differences in the CO oxidation mechanism on Rh atoms and clusters.

36 MATERIALS SCIENCE↗

Exploring the Effect of Surface Functionality on the Self-Assembly of Polyoxopalladate Macroions

The solution behavior of the two polyoxo-13-palladates(II) ([Pd(II) 13 As(V) 8 O34 (OH)6 ](8-) and [Pd(II) 13 (As(V) Ph)8 O32 ](6-) ) was studied in detail. We discovered that the countercation-mediated attraction is the driving force for their self-assembly into larger architectures. However, the presence of phenyl groups in the periphery of [Pd(II) 13 (As(V) Ph)8 O32 ](6-) results in an enhanced attraction among these polyanions through hydrophobic interactions, which leads to completely different trends of assembly size for these two very similar clusters when decreasing solvent polarity. An increase of assembly size with increasing solvent polarity was observed for [Pd(II) 13 (As(V) Ph)8 O32 ](6-) , whereas for [Pd(II) 13 As (V) 8 O34 (OH)6 ](8-) it was the opposite, due to the absence of hydrophobic interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Surface Modifications of Kraft Wood Pulp Cellulose Fibres on Improving the Mechanical Properties of Cellulose Fibre/Latex Composites

In this work, three composites with different contents (5, 10, and 15% w/w) of kraft pulp fibre were produced as reinforcing elements for natural latex matrix and the mechanical properties were evaluated. In order to improve the interfacial adhesion between the matrix and the reinforcing element, chemical modifications were carried out on the surface of the fibres using octanoyl and benzoyl chlorides as modifying agents. The extension of chemical modification of the fibres was visualized by the presence of absorption bands in the spectroscopy analyzes of the modified fibre in relation to the crude fibre (ester carbonyl 1700–1740 cm{sup −1}); in addition, the hydroxyl band was preserved, which indicates a modification of surface character. The modified fibres became more hydrophobic due to the decrease in surface energy and the change in the dispersive and polar components. An increase in the storage modulus was observed for the composites with surface-modified fibres, which agrees with the improved dispersion between the surface-modified fibres and the matrix verified by means of scanning electron microscopy images. The incorporation of fibres did not cause changes in the thermal properties of the composites.

36 MATERIALS SCIENCE↗