Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sinter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Processing and properties of PSZT 95/5 ceramics with varying Ti and Nb substitution

Niobium doped lead-tin-zirconate-titanate ceramics near the PZT 95/5 orthorhombic AFE – rhombohedral FE morphotropic phase boundary Pb 1-0.5y (Zr 0.865-x Ti x Sn 0.135 ) 1-y Nb y O 3 were prepared according to a 2 2+1 factorial design with x = 0.05, 0.07 and y = 0.0155, 0.0195. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1250°C for 6 hours. All compositions were ~98% dense with no detectable secondary phases by XRD. The ceramics exhibited equiaxed grains with intergranular porosity and grain size was ~5 μm, decreasing with niobium substitution. Compositions exhibited remnant polarization values of ~32 μC/cm 2 , increasing with Ti substitution. Depolarization by the hydrostatic pressure induced FE-AFE phase transition was drastically affected by variation of the Ti and Nb substitution, increasing at a rate of 113 MPa / 1% Ti and 21 MPa / 1% Nb. Total depolarization output was insensitive to the change in Ti and Nb substitution, ~32.8 μC/cm 2 for the PSZT ceramics. The R3c-R3m and R3m-Pm3m phase transition temperatures on heating ranged from 90 to 105°C and 183 to 191°C, respectively. Ti substitution stabilized the R3c and R3m phases to higher temperatures, while Nb substitution stabilized the Pm3m phase to lower temperatures. Thermal hysteresis of the phase transitions was also observed in the ceramics, with transition temperature on cooling being as much as 10°C lower.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polymer Entrapment Flash Pyrolysis for the Preparation of Nanoscale Iridium-Free Oxygen Evolution Electrocatalysts

This paper describes the use of a new polymer entrapment flash pyrolysis (PEFP) method for making nanoscale yttrium ruthenate (Y 2 Ru 2 O 7-δ ) electrocatalysts. Here, this approach effectively reduced the synthesis temperature of phase-pure pyrochlore catalysts from 1000 °C to 550 °C, and greatly suppressed the sintering of catalyst particles. The supported nanocrystalline Y 2 Ru 2 O 7-δ catalysts showed enhanced activity towards oxygen evolution reaction (OER) in acidic electrolyte and were stable at 1.50 V for the comparative study (>20 h) under the current density of 10 mA/cm 2 geo in chronopotentiometry testing. This is equivalent to an overpotential value of 270 mV, about half of that of the reference IrO 2 catalyst. X-ray absorption spectroscopy (XAS) and transmission electron microscopy (TEM) analysis showed that the high-surface-area Y 2 Ru 2 O 7-δ catalyst had an oxygen-deficient structure. This study provides a route to the synthesis of fine ceramic (or oxide)-based electrocatalysts for making high-performing electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Preparation and Photocatalytic Hydrogen Production of TiO 2 /(AlMnCoNiZn) 3 O 4 Nanocomposites

Photocatalytic water splitting is a promising strategy for addressing the global energy crisis and environmental pollution. In this study, spinel-type high-entropy oxide (HEO) nanoparticles, (AlMnCoNiZn) 3 O 4 , were successfully synthesized via a solution combustion method. TiO 2 /(AlMnCoNiZn) 3 O 4 nanocomposites with varying molar ratios were subsequently fabricated through solid-state sintering, and their photocatalytic water-splitting performance was systematically investigated. The hydrogen production rate initially increased and then decreased with increasing TiO 2 content. The optimal nanocomposite achieved a hydrogen evolution rate of 1450 μmol·h −1 ·g −1 under simulated sunlight irradiation, which is 2.2 times higher than that of pure TiO 2 nanoparticles. In addition, the TiO 2 /(AlMnCoNiZn) 3 O 4 nanocomposites exhibited significantly improved photocorrosion resistance compared with TiO 2 nanoparticles. After 12 h irradiation under a 500-W high-pressure mercury lamp, the hydrogen production rates of the nanocomposites and pure TiO 2 retained 79.3% and 5.47% of their initial values, respectively. These results demonstrate the important role of (AlMnCoNiZn) 3 O 4 and other HEOs in enhancing the photocatalytic performance of nanoheterojunction catalysts. Lastly, this work broadens the potential applications of (AlMnCoNiZn) 3 O 4 and related HEO materials in the field of photocatalysis.

Heterojunction↗
DOE OSTI2025

A Mössbauer Spectroscopy Investigation of Nickel‐Zinc Ferrites Synthesized by a Self‐Combustion Method for Soft Magnetic Core Applications

Soft ferrites are materials of interest for magnetic cores, as used for wireless charging transformers. Their low permeabilities, high resistivity, and magnetic polarization make them interesting for high-power electric vehicle charging and drive systems. The nickel-zinc-doped ferrites are of particular interest; however, the compositional space is quite large with respect to dopant concentrations, stoichiometric ratios and synthesis technique. Nickel-zinc spinel ferrites with varying nickel-zinc ratios prepared by a self-combustion reaction followed by heat treatment exhibit good crystallinity, and their low-temperature Mössbauer spectra show local magnetism and site occupation in agreement with materials prepared by solid-state reaction. Thus, the combustion synthesis method offers a facile tunability of compositions, which, combined with the possibility of rapid characterization of atomic-scale magnetism by Mössbauer spectroscopy, enables advances in the compositional and processing space at a fast pace. Low-temperature Mössbauer spectroscopy data for samples with increasing nickel content reveals a systematic increase in average hyperfine field (2.8 T/Ni) and decrease in average isomer shift (−0.036 mm/s/Ni) that can determine the nickel/zinc content, even in the absence of applied magnetic field data. Furthermore, a gradual evolution of color is also observed with increasing nickel content, albeit trends in color depend on sintering conditions.

Mössbauer spectroscopy↗
DOE OSTI2021

Persistent Structure and Frustrated Magnetism in High Entropy Rare-Earth Zirconates

The configurational complexity and distinct local atomic environments of high entropy oxides remain largely unexplored, leaving structure-property relationships and the hypothesis that the family offers rich tunability for applications ambiguous. This work investigates the influence of cation size and materials synthesis in determining the resulting structure and magnetic properties of a family of high entropy rare-earth zirconates (HEREZs, nominal composition RE 2 Zr 2 O 7 with RE = rare-earth element combinations including Eu, Gd, Tb, Dy, Ho, La, or Sc). Here, the structural characterization of the series is examined through synchrotron X-ray diffraction and pair distribution function analysis, and electron microscopy, demonstrating average defect-fluorite structures with considerable local disorder, in all samples. The surface morphology and particle sizes are found to vary significantly with preparation method, with irregular micron-sized particles formed by high temperature sintering routes, spherical nanoparticles resulting from chemical co-precipitation methods, and porous nanoparticle agglomerates resulting from polymer steric entrapment synthesis. In agreement with the disordered cation distribution found across all samples, magnetic measurements indicate that all synthesized HEREZs show frustrated magnetic behavior, as seen in a number of single-component RE 2 Zr 2 O 7 pyrochlore oxides. These findings advance the understanding of the local structure of high entropy oxides and demonstrate strategies for designing nanostructured morphologies in the class.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanism of Contrasting Ionic Conductivities in Li 2 ZrCl 6 via I and Br Substitution

Understanding the complex structural and chemical factors that influence ionic conduction mechanisms is paramount for developing advanced inorganic superionic conductors in all‐solid‐state batteries, particularly halide solid electrolytes with excellent electrochemical oxidative stability and mechanical sinterability. Herein, contrasting ionic conduction behaviors in I − and Br − substituted Li 2 ZrCl 6 are revealed by combining experimental structural analyses and theoretical calculations. The inter‐slab distance along the c ‐axis, which varies with the anion substitution and M2‐M3 site disorder, is a key factor for opening the ab ‐plane conduction and facilitating the overall Li + conduction. Increased M3 site occupancy generally leads to contracted inter‐slab distance. The substantial increase in Li + conductivity upon I substitution (from 0.40 to 0.91 mS cm −1 ) originates from a sufficiently expanded lattice volume owing to its large ionic radii (I − = 2.20 Å), particularly inter‐slab distance that facilitates the ab intra‐plane Li + conduction, which also benefits from decreased M2‐M3 disorder. In contrast, Br (Br − = 1.96 Å) substitution results in insufficiently expanded Li + channels, which, exacerbated by increased M2‐M3 disorder, leads to degradation in Li + conductivity. Implementing I − substituted Li 2 ZrCl 6 resulted in superior electrochemical performance in LiCoO 2 ||Li‐In cells compared to those with an unsubstituted catholyte.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Elucidating Pore Network Evolution in Laboratory‐ and Shaft‐Furnace Hydrogen‐Reduced Iron Pellets Using Nanotomographic Characterization

Direct reduced iron (DRI) is an increasingly important feedstock for modern steelmaking. Fundamental research into DRI properties is limited by the discrepancy between the behavior of industrially produced pellets and laboratory‐produced pellets, leading to nongeneralizable conclusions from laboratory work. Here, in this study, a detailed nano‐computed tomographic characterization of ore pellets, hydrogen DRI reduced in a pilot‐scale shaft furnace, and laboratory‐reduced DRI is presented to better understand the microstructurally influenced property differences between the two. The shaft‐furnace‐reduced pellets show lower overall porosity but larger average pore volume thickness and solid volume thickness than the laboratory‐reduced pellets. This effect is attributed to increased sintering behavior in the shaft furnace case. All pellet types show almost entirely connected pore volumes. The tortuosity of the pores is shown to increase with a degree of reduction, though the shaft furnace pellets show lower tortuosity than the laboratory‐reduced pellets. Again, this difference is attributed to the larger pore volume thickness for shaft‐furnace‐reduced pellets.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Manufacturing and stiffness constraints for topology optimized periodic structures

Topology optimization (TO) is commonly applied to design the unit cells of periodic structures. For example, metamaterials, lattice structures, phononic crystals (PhC), and photonic crystals (PC) have all been previously designed via TO. Unfortunately, the optimal structures for certain design objectives, e.g., bandgaps, are often impossible to manufacture as they have disconnected regions or “islands” of solid material (ISM) that are not self-supporting. Additionally, designs with enclosed void space (EVS) are problematic for additive manufacturing (AM) since support material or pre-sintered powder cannot be removed after manufacturing. We present a series of constraints that may be incorporated into any TO framework to ensure structures are self-supporting without enclosed voids. Additionally, we employ homogenization-based constraints that allow the designer to tune the elastic stiffness and isotropy of the optimized design. The proposed constraints are evaluated on example microstructures and utilized in a simple optimization test problem to highlight their abilities and limitations so that guidelines for appropriate combinations of constraints may be proposed. Effective constraint combinations are demonstrated on the design of 3D photonic crystals for maximum bandgap subject to manufacturing and stiffness constraints.

42 ENGINEERING↗
DOE OSTI2021

MADE3D: Enabling the next generation of high-torque density wind generators by additive design and 3D printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments—especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technolgies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

17 WIND ENERGY↗
DOE OSTI2021

Pulsed electric current joining of oxide-dispersion-strengthened austenitic steels

The solid-state joining of oxide-dispersion-strengthened (ODS) austenitic steels was achieved using a pulsed electric current joining (PECJ) process. Microstructures of the austenitic grain structures and oxide dispersions in the joint areas were characterized using electron microscopy. Negligible grain growth was observed in austenitic grain structures, while slight coarsening of oxide dispersions occurred at a short holding time. The mechanisms of the PECJ process may involve three steps that occur simultaneously, including the sintering of mechanical alloying powders in the bonding layer, formation of oxide dispersions, and bonding of the mechanical alloying powders with the base alloy. The high hardness and irradiation resistance of ODS alloys were retained in the joint areas. This research revealed the fundamental mechanisms during the PECJ process, which is beneficial for its potential applications during the advanced manufacturing of ODS alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Aluminum/SmCo 5 composites for structural and magnetic applications

Metal-bonded magnetic composites (MBMCs) present a promising alternative to dense sintered magnets, particularly for intricate components. Compared to polymer-based bonded magnets, MBMCs have wider applicability in harsh environments. In this paper, we demonstrate a solid-state shear-based manufacturing technique to introduce localized magnetization into a paramagnetic aluminum matrix by embedding SmCo5 permanent magnet particles. Our magnetic composites display hard magnetic behavior with a coercivity of 13 kOe and a remanent magnetization of 4.32 emu/g. In addition to magnetization, we also report a 9% improvement in Young’s modulus. Despite the local temperature rise during processing, the magnetic phases didn’t decompose into unwanted phases, preserving the composite's hard magnetic properties. Creation of an interfacial metallurgical bond with the matrix ensured the suitability of the composites for structural applications. Our study investigates the mechanical, and functional properties of composites, paving the way for lightweight structural magnetic composites with a transformative potential in the aerospace, nuclear, and automotive applications. This work underscores the potential for further optimization and development to drive innovations in magnet and equipment design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Syntheses and Crystal Structures of Rare-Earth Oxyapatites Ca 2 RE 8 (SiO 4 ) 6 O 2 (RE = Pr, Tb, Ho, Tm)

Four different rare-earth oxyapatites of Ca 2 RE 8 (SiO 4 ) 6 O 2 (RE = Pr, Tb, Ho, Tm) were synthesized using a solution-based method followed by drying, calcination, and high-temperature sintering in air. X-ray powder diffraction and Raman spectroscopy were performed on the synthesized oxyapatites. Here, the RE oxyapatites crystallize in the hexagonal space group P6 3 /m with similar unit cell parameters, increasing linearly with larger RE cations. The unit cell volumes increase linearly whereas the densities decrease nonlinearly with larger RE cations. Raman spectra showed intense bands of the symmetric bending and stretching modes of SiO 4 at ~ 400 and 860 cm -1 regions, respectively. The bands generally shifted to higher frequencies with smaller RE cations in the structures.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Metal alloy microparticle tagging of UO 2 fuel pellets for nuclear forensics

A tagging strategy for UO 2 fuel pellets will be discussed which involves the creation of alloyed metal microparticles that can be tuned to create a unique identification (“barcode”) indicating provenance of the pellets. These specialized markers would contain high temperature resistant materials, such as Ti, Mo, and Cr, in small quantities such that they do not interfere with the performance of the pellets but are recoverable by standard analytical techniques. The Amazemet rePowder ultrasonic atomization system was used to manufacture the microparticles, and sample pellets were fabricated and sintered containing these dopants. Various techniques, such as Scanning Electron Microscopy (SEM) and Electron Probe Microanalysis (EPMA), were used to evaluate these sample pellets to determine if particles (and their alloy compositions) were recoverable. Details on how the particles were manufactured and characterized will be detailed, as well as results from their incorporation into test pellets. Next steps will involve the scale of this technique using more conventional mass production methods, as well as the implementation of other alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Metal Powder Recyclability in Binder Jet Additive Manufacturing

The recyclability of 316L stainless steel powder in the binder jetting process has been determined. The powder characterization results demonstrated a 22% increase in the number of coarse particles (> 30 µm) and an 18.2% reduction in the number of small particles (< 10 µm) after recycling up to 16 times. A few elongated and irregular-shaped particles were found after recycling, possibly due to particle agglomeration during handling and sieving. Here, a negligible increase in the oxygen content by 0.036% was detected in the recycled powder. The density of sintered parts produced using recycled powder was approximately 1.5% lower than when using fresh powder due to the changes in the particle size distribution and the flowability of the powder caused by the changes in morphology. Final parts built using fresh and recycled powder showed similar hardness (155 ± 3 HV and 165 ± 9 HV) and yield strength (206 ± 16 MPa and 192 ± 10 MPa), respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Advances in Processing, Manufacturing, and Applications of Magnetic Materials

Magnetic materials are increasingly important for many green energy technologies. Probably, the best known of these are permanent magnets. They are used to supply a magnetic field and are widely used in actuators, motors, generators, data storage, and sensors. These are “hard magnets,” meaning that they retain a large permanent magnetization (difficult to be demagnetized), which is what makes them so useful in motors where an opposing magnetic field can be used to push against them. A coercivity (resistance to demagnetization) of ~400 Oe (32,000 A/m) or more is typically the threshold value for a hard magnet and is typical of isotropic sintered ferrite (SrFe 12 O 19 ) such as found in many “refrigerator magnets.” Comparably important soft magnets are useful for directing magnetic fields and can be very easily (de)magnetized. As such, they typically have a coercivity < 12.5 Oe (1000 A/m), and specialized very soft magnets can have coercivities < 0.00125 Oe (1 A/m). Some common applications include coil cores, transformer cores, and magnetic shielding. Additionally, they are important for many AC electrical applications such as inductors, filters, and resonators, particularly at high frequencies up to and including microwaves.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Manufacturing Processes for Permanent Magnets: Part II—Bonding and Emerging Methods

Abstract Permanent magnets produce magnetic fields and maintain the field even in the presence of an opposing magnetic field. They are widely used in electric machines, electronics, and medical devices. Part I reviews the conventional manufacturing processes for commercial magnets, including Nd-Fe-B, Sm-Co, alnico, and ferrite in cast and sintered forms. In Part II, bonding, emerging advanced manufacturing processes, as well as magnet recycling methods are briefly reviewed for their current status, challenges, and future directions.

Cui, Jun (ORCID:0000000179118172)↗
DOE OSTI2022

Powder Metallurgy HIP Process Study and Mechanical Property Evaluations for IN740H

The effects of hot isostatic pressing (HIP) parameters and powder size distribution (PSD) on the resulting microstructure and properties of powder metallurgy (P/M) IN740H have been investigated. Properties can be substantially tailored through the appropriate management of these parameters. Applying a thermal presoak to the input powder prior to the sintering stage of HIP can significantly increase average grain size and coarse grain fraction, enabling a trade for improved creep resistance at the expense of tensile strength. Here, powder thermal presoak was found to have a larger impact on microstructure and properties than the use of a coarser PSD alone. Additionally, substantial grain growth and grain boundary migration is observed in P/M IN740H at HIP temperatures above 1260°C. Given its inherently finer grain size, P/M HIP IN740H typically outperforms its cast and wrought counterparts in tensile response. Creep life at 700–800°C was inferior to wrought due to PPBs coincident with grain boundaries which served as cavity nucleation sites, leading to lower creep ductility. The ability to adjust the microstructure toward a more balanced creep and tensile behavior allows P/M HIP IN740H to be considered for high-temperature applications in advanced ultra-supercritical steam and supercritical carbon dioxide power cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Heterogeneous 3D Morphological Evolution of Ni Microparticles in Molten Salts: Visualized by Operando Synchrotron X-ray Nano-tomography

Ni-based superalloys are promising materials for high-temperature molten salt (MS) energy generation and storage. Studying morphological and chemical evolution of pure Ni in MS provides fundamental knowledge for MS technologies and corrosion mitigation. Here, in this study, real-time 3D morphological changes of Ni microparticles in molten KCl-MgCl 2 were studied by operando synchrotron X-ray nano-tomography at 700°C. Rapid Ni particle agglomeration occurred, without significant chemical reactions, such as oxide or chloride formation. The morphological growth evolved differently from classical coarsening or sintering behaviors and occurred nonuniformly, with other regions showing slight dissolution of Ni. Ni nanoparticles were found to be dispersed in many areas of the samples, either from microparticle dissolution or other radiation-induced nanoparticle formation mechanisms. This study discusses important factors, i.e., thermal gradient, amounts of salt and metals, and radiation effect, that influence morphological changes of materials in MS, critical for fundamental understanding of material–MS interactions as well as for practical applications.

36 MATERIALS SCIENCE↗