Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shear flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

An innovative and alternative approach toward gear fabrication

In this paper, we present the first demonstration of single-step gear manufacturing via an innovative in-situ friction stir forging approach. This novel process is a natural extension to the friction stir processing technique and relies on shear and normal stresses to form the complex shapes. Friction stir welding pin tool with shoulder is plunged at high revolutions per minute (rpm) into the sample to heat it to the desired temperature and enable plastic flow. Then, the tool is forged at high plunge rate to form the desired structurally-sound and defect free complex shapes. To better visualize the process the experiments are complemented by a 3D thermomechanically coupled, smoothed particle hydrodynamics (SPH) model to understand the material flow pattern both radially and through thickness in the gear teeth, plastic strain distribution, and temperature profile. We have demonstrated application of I-FSF to inherently poor formable AZ31 Mg, AA 7075-T6, and AA5083–10 vol% TiB 2 composite and fabricated 14-tooth spur gears from these materials with minimal farther machining. In conclusion, microstructure of the forged gears exhibited a directional material flow pattern due to the normal forging action and refinement of grains to 6–13 μm through dynamically recrystallization across the radial, through-thickness direction, which is in good agreement with the corresponding SPH simulation results.

42 ENGINEERING↗
DOE OSTI2022

Mixing Driven by Critical Reflection of Near-Inertial Waves over the Texas–Louisiana Shelf

Studies of internal wave-driven mixing in the coastal ocean have been focused on internal tides, while wind-driven near-inertial waves (NIWs) have received less attention in this regard. Here, this study demonstrates a scenario of NIW-driven mixing over the Texas–Louisiana shelf. Supported by a high-resolution simulation over the shelf, the NIWs driven by land–sea breeze radiate downward at a sharp front and enhance the mixing in the bottom boundary layer where the NIWs are focused because of slantwise critical reflection. The criterion for slantwise critical reflection of NIWs is ω=$\sqrt{f{^2}+s^{2}_{bot}N{^2}(1-s_{ρ}/s_{bot})}$ (where ω is the wave frequency, s bot is the bottom slope, and s ρ is the isopycnal slope), under the assumption that the mean flow is in a thermal wind balance and only varies in the slope-normal direction. The mechanism driving the enhanced mixing is explored in an idealized simulation. During slantwise critical reflection, NIWs are amplified with enhanced shear and periodically destratify a bottom boundary layer via differential buoyancy advection, leading to periodically enhanced mixing. Turbulent transport of tracers is also enhanced during slantwise critical reflection of NIWs, which has implications for bottom hypoxia over the Texas–Louisiana shelf.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

A direct numerical simulation study for confined non-isothermal jet impingement at moderate nozzle-to-plate distances: Capturing jet-to-ambient density effects

A direct numerical simulation (DNS) campaign is deployed for a series of confined downward oriented, non-isothermal turbulent impinging jet configurations. A baseline Reynolds number of 9960 is obtained through a precursor DNS pipe flow simulation (Re τ = 505). Three jet temperature configurations (confinement height to nozzle diameter of three) enter a cylindrical domain that share ambient and impingement plate temperatures (298.15 K). The range of jet temperatures are crafted such that the ratio of inlet to ambient density varies from unity to 0.52, showcasing the effect of density disparity on flow characteristics such as core collapse, radial mixing of momentum and energy, near-wall stagnation behavior, wall-jet profiles, and large-scale vortical structures. Surface quantities provided include mean radial heat flux and wall-shear stress profiles, and heat flux histograms at select radial stations. Results showcase increased radial normal stresses for higher temperature jets that support increased mixing, resulting in large-scale recirculation structures that are smaller, while retaining similar normalized radial wall profiles for shear stress, heat flux and pressure. Furthermore, radial plots for wall shear stress and Nusselt number showcase strong radial decay as compared to previous configurations that share similar jet and ambient temperatures. For the 373.15 K case, a Gaussian-like histogram for heat fluxes at the impingement plate transitions to a log-normal profile as radial distances increase. In contrast, the 573.15 K configuration displays a bi-modal heat flux characteristic at the impingement plate, and in similar manner to the moderate temperature counterpart, transitions to a log-normal profile at larger radial distances.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Implications of inertial subrange scaling for stably stratified mixing

In this work, we investigate the effects of the turbulent dynamic range on active scalar mixing in stably stratified turbulence by adapting the theoretical passive scalar modelling and demonstrating their usefulness through consideration of the results of direct numerical simulations of statistically stationary homogeneous stratified and sheared turbulence. By analysis of inertial and inertial–convective subrange scalings, we show that the relationship between the active scalar and turbulence time scales is predicted by the ratio of the Kolmogorov and Obukhov–Corrsin constants, provided mean flow parameters permit the two subrange scalings to be appropriate approximations. We use the resulting relationship between time scales to parameterise an appropriate turbulent mixing coefficient $\varGamma \equiv \chi /\epsilon$, defined here as the ratio of available potential energy ($E_p$) and turbulent kinetic energy ($E_k$) dissipation rates. With the analysis presented here, we show that $\varGamma$ can be estimated by $E_p,E_k$ and a universal constant provided an appropriate Reynolds number is sufficiently high. This large Reynolds number regime appears here to occur at $ {{Re_b}} \equiv \epsilon / \nu N^{2} \gtrapprox 300$ where $\nu$ is the kinematic viscosity and $N$ is the characteristic buoyancy frequency. We propose a model framework for irreversible diapycnal mixing with robust theoretical parametrisation and asymptotic behaviour in this high-$ {{Re_b}}$ limit.

42 ENGINEERING↗
DOE OSTI2022

Dynamic Strength of Iron at High Pressures and Strain Rates

Accurate modeling of meteorite impacts, and deformation of planetary cores require characterization of the flow strength and in-elasticity of iron in its different phases. In this letter, we investigate the flow strength of both the ambient α-phase and high-pressure ϵ-phase of iron at strain-rates of 1 × 10 5 s –1 and pressures up to 42 GPa using high pressure - pressure shear plate impact experiments. We report the strength of the ϵ-iron to be significantly higher than α-phase but consequently one order smaller than the previously reported dynamic strength at high pressures. As a result, the complete stress-strain response of the ϵ-phase is reported for the first time.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Monsoon Depression Amplification by Horizontal Shear and Humidity Gradients: A Shallow Water Perspective

Transient, synoptic-scale vortices produce a large fraction of total rainfall in most monsoon regions and are often associated with extreme precipitation. However, the mechanism of their amplification remains a topic of active research. For monsoon depressions, which are the most prominent synoptic-scale vortex in the Asian–Australian monsoon, recent work has suggested that meridional gradients in zonal wind in the vortex environment may produce growth through barotropic instability, while meridional gradients in environmental humidity have also been proposed to cause amplification through coupling with precipitating convection. Here, a two-dimensional shallow water model on a sphere with parameterized precipitation is used to examine the relative role played by these two environmental gradients. By systematically varying the meridional moisture gradient and meridional wind shear for both weak, quasi-linear waves and finite-amplitude isolated vortices, we show that rotational winds in the initial vortex are amplified most strongly by meridional shear of the environmental zonal wind, while vortex precipitation rates are most sensitive to environmental moisture gradients. The growth rate in the presence of both gradients is less than the sum of growth rates in the presence of isolated gradients, as the phase relation between moisture and vorticity anomalies becomes distorted with increasing shear. In conclusion, these results suggest that background meridional gradients in both zonal wind and environmental humidity can contribute to the amplification of vortices to monsoon depression strength, but with some degree of decoupling of the dry rotational flow and the moist convection.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Nonlinear Alfvén instability simulation and EP transport for ITER reversed shear (steady-state) and monotonic q-profile regimes *

The nonlinear evolution and dynamics of energetic particle (EP) driven instabilities in both steady-state (reversed shear q-profile) and monotonic q-profile regimes of ITER are examined using the global gyro-Landau closure model FAR3d. Both neutral beam and alpha components are included, leading to synergistic effects between the two populations. In order to maintain computational feasibility, the present nonlinear simulation includes all toroidal mode numbers ranging from n = 0 to 15. It cannot be excluded that n’s above this range could introduce larger linear growth rates; however, as indicated from the results, the n = 0 to 15 range is sufficient to provide a strong linear drive and significant nonlinear transport effects. While the toroidal mode numbers n = 6,13 dominate the linear instability growth phase, nonlinear energy transfers in the saturated phase reverse this trend, leading to the dominance of lower n’s in the saturated phase of the simulation. Zonal flow structure generation and EP density flattening are further consequences of the nonlinear phase. The density profile flattening is caused by collectively driven EP radial transport fluxes, which have non-local characteristics. Instantaneous alpha particle transport fluxes are significant (Γ α ~ 2 x 10 20 m –2 s –1 ) for the reversed shear regime and lower (Γ α ~ 1.1 x 10 20 m –2 s –1 ) for the monotonic q-profile case.

AE↗
DOE OSTI2022

Stress Birth and Death: Disruptive Computational Mechanics and Novel Diagnostics for Fluid-to-Solid Transitions

Many materials of interest to Sandia transition from fluid to solid or have regions of both phases coexisting simultaneously. Currently there are, unfortunately, no material models that can accurately predict this material response. This is relevant to applications that "birth stress" related to geoscience, nuclear safety, manufacturing, energy production and bioscience. Accurately capturing solidification and residual stress enables fully predictive simulations of the evolving front shape or final product. Accurately resolving flow of proppants or blood could reduce environmental impact or lead to better treatments for heart attacks, thrombosis, or aneurism. We will address a science question in this proposal: When does residual stress develop during the critical transition from liquid to solid and how does it affect material deformation? Our hypothesis is that these early phases of stress development are critical to predictive simulation of material performance, net shape, and aging. In this project, we use advanced constitutive models with yield stress to represent both fluid and solid behavior simultaneously. The report provides an abbreviated description of the results from our LDRD "Stress Birth and Death: Disruptive Computational Mechanics and Novel Diagnostics for Fluid-to-Solid Transitions," since we have written four papers that document the work in detail and which we reference. We give highlights of the work and describe the gravitationally driven flow visualization experiment on a model yield stress fluid, Carbopol, at various concentrations and flow rates. We were able to collapse the data on a single master curve by showing it was self-similar. We also describe the Carbopol rheology and the constitutive equations of interest including the Bingham-Carreau-Yasuda model, the Saramito model, and the HB-Saramito model including parameter estimation for the shear and oscillatory rheology. We present several computational models including the 3D moving mesh simulations of both the Saramito models and Bingham-Carreau-Yasuda (BCY) model. We also show results from the BCY model using a 3D level set method and two different ways of handling reduced order Hele-Shaw modeling for generalized Newtonian fluids. We present some first ever two-dimensional results for the modified Jeffries Kamani-Donley-Rogers constitutive equation developed during this project. We include some recent results with a successful Saramito-level set coupling that allows us to tackle problems with complex geometries like mold filling in a thin gap with an obstacle, without the need for remeshing or remapping. We report on some experiments for curing systems where fluorescent particles are used to track material flow. These experiments were carried out in an oven on Sylgard 184 as a model polymerizing system. We conclude the report with a summary of accomplishments and some thoughts on follow-on work.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Film Cooling Performance Prediction for Air and Supercritical CO 2

The current study explores the possibility of cooling the vanes and blades of a direct-fired sCO 2 turbine using film cooling. The operating conditions of a direct-fired sCO 2 cycle and thermophysical properties of the fluid at those conditions can alter the flow field characteristics of the coolant jet and its mixing with the mainstream. Very little information is present in the literature regarding the performance of film cooling geometries employing supercritical CO 2 . The objective of this study is to estimate the resulting film cooling effectiveness while also capturing the effects of the crossflow-to-mainstream velocity ratio on the coolant jet. Herein, a computational fluid dynamic model is used to study the coolant jet exiting a cylindrical hole located on a flat plate, with the coolant fed by an internal channel. Steady-state Reynolds-averaged Navier–Stokes equations were solved along with the (shear-stress transport) SST k–ω model to provide the turbulence closure. The operating conditions for the direct-fired sCO 2 turbine are obtained using an in-house Cooled Turbine Model. Numerical predictions revealed that the crossflow effects and jet lift-off were more pronounced in the case of sCO 2 when compared to air. Spatial distribution of flow field and cooling effectiveness are presented at different operating conditions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Hall–Petch strengthening limit through partially active segregation in nanocrystalline Ag-Cu alloys

The breakdown from grain-size strengthening to softening mechanisms is generally well understood for high-purity nanocrystalline materials when the mean grain size decreases to the nanometer range. In nanocrystalline alloys, however, the stabilization of nanosized grains by grain-boundary solute segregation complicates the above mechanisms. Moreover, current segregation models have little predictive power for determining the optimal solute content that maximizes Hall-Petch strengthening effects. In this article, using large-scale hybrid Monte-Carlo/molecular dynamic simulations, we present a systematic study of the Hall–Petch breakdown in Cu-segregated Ag alloys with grain sizes ranging from 8 nm to 59 nm, where three concentration-dependent regimes of plasticity are described: (1) Classical segregation strengthening behavior at low solute contents, (2) shear band-induced softening at high solute contents, and (3) a previously unknown, but extended plateau of maximum strengths for intermediate solute contents from 4 to 15 at.%, which we term as nanocrystalline Sterling silver. We find that flow strengths in nanocrystalline Sterling alloys naturally exhibit a zero-slope limit at the smallest grain sizes that is well below the ideal Hall–Petch strengthening trend. This phenomenon results from partially active grain-boundary segregation that acts to influence interfacial plasticity in some, but not all, grain boundary regions. Our findings amplify the atomic nature of solute segregation and interaction at grain boundaries and its complex roles on grain boundary-mediated plasticity mechanisms in nanocrystalline alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A micromechanical hydro-mechanical-damage coupled model for layered rocks considering multi-scale structures

An anisotropic Hydro-Mechanical-Damage coupled model was established in the framework of thermodynamics for saturated layered rocks, which contain arbitrarily-distributed cracks of smaller scales and orientated bedding planes of much larger scales. Here, the proposed model considers the anisotropic damage growth and frictional sliding of cracks and shear sliding and dilatancy of bedding planes, as well as the interaction between cracks and bedding planes. Numerical implementation of the nonlinear coupled model was developed based on TOUGHREACT, which is a well-established simulator for multiphase fluid flow and reactive transport analysis. The proposed model was first validated with laboratory water injection test results on rock blocks, and then used to study the effects of injection rates, in situ stresses and bedding planes on fluid injection processes at the field scale, demonstrating the importance to consider the variation of multi-scale structures for better understanding the coupled Hydro-Mechanical responses in layered rocks.

58 GEOSCIENCES↗
DOE OSTI2022

Theory of mean E × B shear in a stochastic magnetic field: ambipolarity breaking and radial current

The mean E $ \times $ B shear in a stochastic magnetic field is calculated, using the radial force balance relation and transport equations. This analysis is relevant to the L → H transition with resonant magnetic perturbations, and special focus is placed upon the physics of non-ambipolar transport and radial current. The key physical process is the flow of fluctuating currents along wandering magnetic fields. The increments in poloidal and toroidal rotation, density and ion pressure are calculated. The radial envelope of the magnetic perturbations inside the plasma defines a new scale ${\ell _{{\text{env}}}}$, which is the characteristic scale of the magnetic fluctuation intensity profile. Here, the net particle outflow due to stochastic magnetic fields is calculated and is determined by the net radial current through the separatrix. Implications for the L → H transition are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Sodium Hydrogen Sensor and Acoustic Flow Sensor Development

This report documents the development of diffusion-type hydrogen meters (DTHMs) as part of a steam generator leak detection system (SGLDS) of sodium-cooled fast reactors (SFR) and the demonstration of the capabilities of acoustic flowmeters, including a commercial UTFM (Flexim FLUXUS F721) and an Argonne HT acoustic flowmeter running on shear-to-longitudinal mode. It also evaluates two Argonne permanent magnet flowmeters (PMFMs).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

A variational phase-field framework for thermal softening and dynamic ductile fracture

A variational phase field model for dynamic ductile fracture is presented. Here, the model is designed for elasto-viscoplastic materials subjected to rapid deformations in which the effects of heat generation and material softening are dominant. The variational framework allows for the consistent inclusion of plastic dissipation in the heat equation as well as thermal softening. It employs a coalescence function to degrade fracture energy during regimes of high plastic flow. A variationally consistent form of the Johnson–Cook model is developed for use with the framework. Results from various benchmark problems in dynamic ductile fracture are presented to demonstrate capabilities. In particular, the ability of the model to regularize shear band formation and subsequent damage evolution in two- and three-dimensional problems is demonstrated. Importantly, these phenomena are naturally captured through the underlying physics without the need for phenomenological criteria such as stability thresholds for the onset of shear band formation.

42 ENGINEERING↗
DOE OSTI2021

Seismic anisotropy, dominant slip systems and phase transitions in the lowermost mantle

SUMMARY The presence of seismic anisotropy at the base of the Earth's mantle is well established, but there is no consensus on the deformation mechanisms in lower mantle minerals that could explain it. Strong anisotropy in magnesium post-perovskite (pPv) has been invoked, but different studies disagree on the dominant slip systems at play. Here, we aim to further constrain this by implementing the most recent results from atomistic models and high-pressure deformation experiments, coupled with a realistic composition and a 3-D geodynamic model, to compare the resulting deformation-induced anisotropy with seismic observations of the lowermost mantle. We account for forward and reverse phase transitions from bridgmanite (Pv) to pPv. We find that pPv with either dominant (001) or (010) slip can both explain the seismically observed anisotropy in colder regions where downwellings turn to horizontal flow, but only a model with dominant (001) slip matches seismic observations at the root of hotter large-scale upwellings. Allowing for partial melt does not change these conclusions, while it significantly increases the strength of anisotropy and reduces shear and compressional velocities at the base of upwellings.

58 GEOSCIENCES↗
DOE OSTI2020

Elucidating the Impact of Flow on Material-Sensitive Critical Heat Flux and Boiling Heat Transfer Coefficients: An Experimental Study with Various Materials

In this work, steady-state internal flow boiling critical heat flux (CHF) experiments were carried out at 10°C inlet subcooling and atmospheric pressure (84 kPa at an altitude of about 5300 feet) with mass flux ranging from 200 to 2,000 kg/m 2 -s on seven tube materials, including the accident-tolerant fuel cladding candidate FeCrAl (C26M) alloy. At a relatively low flow rate, the sensitivity of CHF to different materials was appreciable (the average difference among the tested materials was 19% at 200 kg/m 2 -s). As the absolute CHF differences stayed constant for higher flow rates, the increased flow rate led to reduced relative CHF differences among the tested materials (average relative difference of 15% at 1,000 kg/m 2 -s). FeCrAl alloy claddings that were oxidized under simulated Light Water Reactor (LWR) conditions yielded CHF comparable to as-received FeCrAl alloy cladding, with less than 1.8% difference. Experimental CHF results imply marginal material sensitivity impacts on the departure from nucleate boiling ratio in steady-state nuclear reactor cores. Yet, for accident progression analysis, material sensitivity may hold importance, as boiling behavior variation at low mass flux is appreciable. Macroscopic material parameters (surface wettability, surface roughness, and thermal properties) do not provide a suitable explanation for observed material-sensitive CHFs. Yet, surface roughness and thermal effusivity revealed power and linear relations, respectively, to the nucleate boiling heat transfer coefficients at low mass flux. At high mass flux, material sensitivity on nucleate boiling heat transfer significantly decreased due to the increased shear stress on boiling surface overwhelming material-related boiling implications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Novel nonwetting solid-infused surfaces for superior fouling mitigation

Fouling is a ubiquitous issue in several environmental and energy applications. Here we introduce novel nonwetting solid-infused surfaces (SIS) with superior anti-fouling characteristics that are durable than conventional nonwetting surfaces in a dynamic flow environment. A systematic study is presented to elucidate the fouling mitigation performance of SIS in comparison to lubricant-infused surface (LIS) and conventional smooth surface. Copper tubes with SIS, LIS or smooth inner walls are fabricated and subjected to accelerated calcium sulfate fouling in a flow fouling experimental setup. Fouling on the various surface types is quantified in terms of asymptotic fouling resistance, and the fundamental morphological differences in the interactions of the foulant and the various surface types are analyzed. Based on a systematic sweep of the parameter combinations using design of experiments and Taguchi analysis, an analytical dependence of asymptotic fouling resistance on the governing parameters namely, Reynolds number, foulant concentration and temperature is derived. The analytical model is shown to predict the asymptotic fouling resistance to within 20% accuracy with a 95% confidence. In addition, for the first time, the effects of shear durability on the fouling mitigation performance of LIS vis-à-vis SIS are studied. It is shown that the novel nonwetting SIS offers a robust option for superior fouling mitigation over LIS in the long run.

42 ENGINEERING↗
DOE OSTI2025

Unsteady- and Steady-State Relative Permeability Study with X-ray and Acoustic Monitoring for CO 2 Storage in Deep Saline Aquifers

In this study, we link the multiphase flow measurements with controls of sedimentary structures (e.g., heterogeneity and anisotropy) on relative permeability to variations in ultrasonic velocities for two deep saline aquifer formations (Entrada and Bluff Sandstones) in the San Juan Basin of the Southwestern USA. The rock specimens were extracted from outcrop sites near Durango, CO, USA. They have distinct differences in grain size, cementation composition, and individual chemical amounts, despite both formations being eolian sandstones. We performed a series of unsteady- and steady-state CO 2 -brine relative permeability experiments under capillary-controlled displacement rates. Unsteady-state experiments were conducted at 71 °C and 9.65 MPa; steady-state experiments were conducted at 85 °C and 22.8 MPa and 89 °C and 24.1 MPa for the Bluff and Entrada Sandstones, respectively. During the unsteady experiments, X-ray computed tomography was used to visualize multiphase flow in porous media and quantify saturations during brine drainage under various flow rates. Scan images and saturation profiles indicate that the CO 2 distribution in the pore volume was strongly impacted by the presence of high-angle cross-laminations, heterogeneous rock structure, and direction of bedding orientation. Those factors contribute to dramatic and quick initial breakthroughs and affect the overall saturation dynamics. Steady-state relative permeability tests were conducted at net flow rates of 1 mL/min for both brine drainage and imbibition. During the experimental steps, the CO 2 fractional flow was increased and decreased for both drainage and imbibition scenarios to mimic the front when CO 2 contacts brine and behind the front when brine enters space previously occupied by CO 2 . It was found that compressional velocity decreased, while shear waves slightly increased as brine saturation decreased. The hysteresis effects for the relative permeability and acoustic velocities were distinct. Furthermore, the CO 2 /brine front stability is quantified by applying a mobility ratio approach to spot saturations at which the boundary line between fluids becomes uneven. The results presented in this work can potentially boost the quality and precision of forecasts for the CO 2 storage projects in which the vertical and horizontal core-scale heterogeneity and anisotropy impact the plume migration within host reservoirs.

carbon dioxide (CO2)↗