Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “radiation physics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Irradiation hardening and ductility loss of Eurofer97 steel variants after neutron irradiation to ITER-TBM relevant conditions

Ten Eurofer97 steel variants, produced by non-standard fabrication-processing routes and modified alloying chemistries, were studied by neutron irradiations in the high flux isotope reactor. The irradiations were performed to ITER-TBM relevant conditions of ~255–350 °C, 2.94–3.24 dpa. We quantified the irradiation-induced degradation of the steels using mechanical property tests. All the steels suffered from irradiation hardening, where a significant increase in Vickers microhardness and yield stress (σ YS ) occurred, accompanied with severe loss of tensile elongation. The extent of hardening was material dependent. For T irr = 300±30 °C, most steels showed σ YS increase in the range of ~30% to as high as ~66%, except for a low temperature tempered steel with σYS increase below 15%. Despite large losses in elongation, most failures were ductile. Significant post-necking ductility was retained with reduction in area (RA) between 65–75%, but <50% for low temperature tempered steels. The ultimate tensile stress to yield stress (σ UTS /σ YS ) ratios decreased significantly after irradiation, highlighting irradiation-induced strain hardening capacity reduction. No major effect of irradiation on the plastic instability stress (σ PIS ) and true fracture stress of the steels was observed. By comparing the tensile stresses in true stress units and with literature, the results suggest that RAFM steel designing should target materials with a large separation between σ PIS and σ YS , to ensure the materials can maintain large work hardening and uniform deformation capability after irradiation. The tensile data of the steels additionally revealed a compelling evidence of an inverse trend between the change in RA and increase in σ YS of the neutron irradiated Eurofer97 type steels.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Validation of the strike point position estimation with the local expansion method for MAST upgrade on the DIII-D tokamak

A local expansion method has been proposed for estimating the strike point position for the advanced divertor configuration on the MAST Upgrade tokamak. The paper discusses the application and assesses the performance of the technique on a long-legged divertor plasma configuration on an operating device - the DIII-D tokamak. A comparison of the spatial location of the outer strike point estimated with the local expansion method against the plasma boundary reconstruction and divertor diagnostics on the DIII-D tokamak is reported. A good agreement with the equilibrium reconstruction and diagnostic data is achieved with respect to estimation of the spatial location of the outer strike point for the long-legged divertor plasma discharge.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

IUPAC-IUGS recommendation on the half-lives of 147 Sm and 146 Sm

In this paper, the IUPAC-IUGS joint Task Group “Isotopes in Geosciences” recommends a value of (106.25 ± 0.38) Ga for the half-life of 147 Sm, and a corresponding decay constant λ 147 = (6.524 ± 0.024) × 10 –12 a –1 , both with a coverage factor k = 2. For the extinct radionuclide 146 Sm two very different half-lives are used in the scientific community ( c . 68 and 103 Ma), to such a degree that no consensus value can be endorsed at present by the Task Group. Pending dedicated re-investigations it is recommended that papers using the 146 Sm decay to quantify the cosmo/geological evolution of (extra)terrestrial samples perform a twin set of calculations using both proposed half-lives.

146Sm↗
DOE OSTI2021

Results from single-shock Marble experiments studying thermonuclear burn in the presence of heterogeneous mix on the National Ignition Facility

The Marble campaign on the National Ignition Facility investigates the effect of heterogeneous mix on thermonuclear burn for comparison to a probability distribution function (PDF) burn model. Marble utilizes plastic capsules filled with deuterated plastic foam and a fill gas containing tritium. As the capsules implode, the deuterium in the foam mixes with the tritium gas, and DT neutrons are produced as the shocks compress and heat the mixture. The yield of DT neutrons is dependent on the uniformity of the mix, with more heterogeneous mix producing fewer neutrons. In Marble, the heterogeneity of the mix is controlled by varying the diameter of voids introduced into the foam. The first NIF Marble campaign has been executed in which the Marble capsules were indirectly driven with a single strong shock using NIF hohlraums. The experiments produce a low-convergence, high-ion-temperature implosion. The ratio of DT to DD neutron yield is largely consistent with uniform atomic mix for fine-pore foam, and increases slightly with void diameter, contrary to 1D simulations using the PDF burn model. Recent 3D high-resolution simulations of similar experiments performed on the Omega Laser Facility suggest an explanation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Observations of multi-ion physics and kinetic effects in a surrogate to the solar CNO reactions

The ‘CNO process’ occurs in heavier stars with finite metallicity in which hydrogen burning is catalyzed in the presence of 12 C. These reactions are more strongly dependent on temperature than the pp cycle reactions, and thus the CNO cycle dominates only in massive stars. For these types of reactions to be studied at ICF facilities such as OMEGA, an implosion platform using heavier nuclei in the fuel and capable of creating ion temperatures on the order of at least 20 keV is required. A potential route to reach these conditions is to take advantage of kinetic effects in low-convergence shock-driven ‘exploding pusher’ implosions. In this experiment, shots were conducted at the OMEGA laser facility using the surrogate reaction 13 C + D. Its cross section is substantially higher than the actual astrophysical CNO reactions. The yield of this reaction in these implosions was much lower than expected. Finally, physical explanations are discussed, with significant species stratification the likely explanation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Influences of shock imprinting on mix in a 3D-printed porous media

Mixing of materials in porous media can cause a significant impact on fusion yield as previously demonstrated by the National Ignition Facility (NIF) MARBLE Campaign. Initially, the reactants are separated, with deuterium in the lattice struts and a tritium gas fill in the voids. Lattice parameters such as the strut thickness and relative pitch, provide a control for the mix parameters in the experiment. Los Alamos National Laboratory’s (LANL) BOSQUE project looks to better understand how the mix of the reactants and shell materials impact the fusion burn and resultant yield on various laser platforms. xRAGE’s Eulerian hydrodynamics and adaptive mesh refinement (AMR) provide the unique ability to study the impacts of multiscale features of complex lattice structures. This modeling provides the ability to measure shock front variations as the wave progress’ through a given media. Initial conditions of the lattice are essential to accurately model mix and burn measured by experiment. By varying the initial orientation and densities of these lattice regions the early time dynamics of how the shock is launched into the system is changed and advocates for the study of resulting effects. In this work, we will study the sensitivities of shock effects in varying 3D printed geometric systems and how these shocks alter the structure and mix in the lattice. We will discuss both preliminary experimental results and simulations to help plan and constrain future experiments where we will study the impact of different lattice geometries and lattice bulk densities. This work concludes with the relative impacts of lattice geometries on shock speeds at different bulk densities and the resultant mix widths due to those shock interactions. We see agreement with theory at the higher end of our bulk density study, however, as we approach lower bulk density systems the dynamics of these interactions begin to change.

2 Photon Polymerization↗
DOE OSTI2022

Collision-Induced Dissociation at TRIUMF's Ion Trap for Atomic and Nuclear science

The performance of high-precision mass spectrometry of radioactive isotopes can often be hindered by large amounts of contamination, including molecular species, stemming from the production of the radioactive beam. In this paper, we report on the development of Collision-Induced Dissociation (CID) as a means of background reduction for experiments at TRIUMF's Ion Trap for Atomic and Nuclear science (TITAN). This study was conducted to characterize the quality and purity of radioactive ion beams and the reduction of molecular contaminants to allow for mass measurements of radioactive isotopes to be done further from nuclear stability. Furthermore, this is the first demonstration of CID at an ISOL-type radioactive ion beam facility, and it is shown that molecular contamination can be reduced up to an order of magnitude.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

A performant energy-conserving particle reweighting method for Particle-in-Cell simulations

A new particle-based reweighting method is developed and demonstrated in the Aleph Particle-in-Cell with Direct Simulation Monte Carlo (PIC-DSMC) program. Novel splitting and merging algorithms ensure that modified particles maintain physically consistent positions and velocities. This method allows a single reweighting simulation to efficiently model plasma evolution over orders of magnitude variation in density, while accurately preserving energy distribution functions (EDFs). Demonstrations on electrostatic sheath and collisional rate dynamics show that reweighting simulations achieve accuracy comparable to fixed weight simulations with substantial computational time savings. This highly performant reweighting method is recommended for modeling plasma applications that require accurate resolution of EDFs or exhibit significant density variations in time or space.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Accelerating eigenvalue computation for nuclear structure calculations via perturbative corrections

Subspace projection methods utilizing perturbative corrections have been proposed for computing the lowest few eigenvalues and corresponding eigenvectors of large Hamiltonian matrices. In this paper, we build upon these methods and introduce the term Subspace Projection with Perturbative Corrections (SPPC) method to refer to this approach. We tailor the SPPC for nuclear many-body Hamiltonians represented in a truncated configuration interaction subspace, i.e., the no-core shell model (NCSM). We use the hierarchical structure of the NCSM Hamiltonian to partition the Hamiltonian as the sum of two matrices. The first matrix corresponds to the Hamiltonian represented in a small configuration space, whereas the second is viewed as the perturbation to the first matrix. Eigenvalues and eigenvectors of the first matrix can be computed efficiently. Because of the split, perturbative corrections to the eigenvectors of the first matrix can be obtained efficiently from the solutions of a sequence of linear systems of equations defined in the small configuration space. These correction vectors can be combined with the approximate eigenvectors of the first matrix to construct a subspace from which more accurate approximations of the desired eigenpairs can be obtained. We show by numerical examples that the SPPC method can be more efficient than conventional iterative methods for solving large-scale eigenvalue problems such as the Lanczos, block Lanczos and the locally optimal block preconditioned conjugate gradient (LOBPCG) method. The method can also be combined with other methods to avoid convergence stagnation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Evaluation of several relevant fractionation processes as possible explanation for radioxenon isotopic activity ratios in samples taken near underground nuclear explosions in shafts and tunnels

Gas samples taken from two historic underground nuclear tests done in 1989 at the Nevada National Security Site (NNSS), formerly the Nevada Test Site (NTS), were examined to determine how xenon isotopes fractionate because of early-time cavity processes, transport through the rock, or dispersal through tunnels. Xenon isotopes are currently being used to distinguish civilian sources of xenon in the atmosphere from sources associated with underground nuclear explosions (UNEs). The two nuclear tests included (1) BARNWELL, a test conducted in a vertical shaft approximately 600 m below ground surface at Pahute Mesa, and (2) DISKO ELM, a horizontal line-of-sight test done in P-tunnel approximately 261 m below the surface of Aqueduct Mesa. Numerical flow and transport models developed for the two sites had mixed success when attempting to match the observed xenon isotope ratios. At the BARNWELL site, the simulated xenon isotope ratios were consistent with measurements from the chimney and ground surface and appeared to have been affected primarily by fractionation during subsurface transport. At the DISKO ELM site, samples taken from two elevations in the chimney failed to show the degree of fractionation predicted by the models during transport and did not show evidence for significant fractionation due to early-time condensation of refractory xenon-precursor radionuclides into the melt glass. Gas samples taken from the adjacent tunnels in the days following the test showed mixed evidence for early-time separation of xenon isotopes from their iodine precursors.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Investigation of the competition between Tl + and Ce 3+ scintillation in Tl2LiYCl6:Ce, an elpasolite scintillator

Li-containing elpasolite scintillators are currently investigated for their ability to detect both thermal neutrons and gamma photons with a single inorganic crystal. The scintillation is typically triggered by using an activator such as Ce. However, when Tl, also a luminescent ion, is present in the matrix, competition between the two centers Tl and Ce can occur. In this study, we are using Ce doped Tl 2 LiYCl 6 to investigate this competition. To this end, the Ce (which substitutes Y) concentration is varied from 0 to 1 in the Tl 2 LiY 1-x CexCl 6 composition. In the low concentration range in which Ce remains a dopant, the photo- and radioluminescence spectra show that the scintillation of Tl 2 LiYCl 6 :Ce is mostly dominated by recombination on intrinsic luminescent centers. For cerium concentrations higher than x = 0.02, very different emissions can be easily distinguished from the photo- and radioluminescence of undoped and low Ce doped Tl 2 LiYCl 6 crystals. These emissions are attributed to the formation of a second phase Tl 2 CeCl 5 , identified by X-ray diffraction. We conclude that the intrinsic luminescence related to Tl dominates the scintillation in the range of concentration for which Ce does substitute on the Y-site.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Point defect evolution under irradiation: Finite size effects and spatio-temporal correlations

The evolution of point defect concentrations under irradiation is controlled by their diffusion properties, and by their formation and elimination mechanisms. The latter includes the mutual recombination of vacancies and interstitials, and the elimination of point defects at sinks. Two models are traditionally used to predict the defect concentration evolution, the standard rate theory (SRT) and the atomistic kinetic Monte Carlo (AKMC). We show in this work a large discrepancy in the defect concentrations between both methods when the average number of defects in the AKMC simulation box is close or lower than one. The reason is that AKMC naturally captures strong space and time correlations between vacancies and interstitials generated by the finite size of the periodic simulation box. These correlations strongly affect the recombination rate and the point defect concentrations. SRT fails to predict such correlations, and the corresponding solution deviates from the more accurate solution given by the AKMC simulation under similar conditions. These finite size correlation effects are strong when the elimination of point defects occurs by recombination only, but can still be significant in the presence of sinks. In order to account for the spacio-temporal correlation in a continuum framework, we introduce a Correlated Pair Theory (CPT). This theory fully takes into account the correlations between vacancy and interstitial pairs and predicts point defect concentrations in good agreement with AKMC simulations. Inversely, if the goal is for the AKMC to reproduce defect concentrations in bulk using small simulation boxes, the naturally occurring correlations need to be corrected. We show here that the CPT can be used to modify the elimination rates in the AKMC simulations, so as to yield point defect concentrations in agreement with SRT.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Disordering of helium gas bubble superlattices in molybdenum under ion irradiation and thermal annealing

Self-organization of gas bubbles causes the formation of an ordered array of nanoscale gas bubbles (a gas bubble superlattice), a highly efficient mechanism for gas storage under irradiation. Here, the stability of helium (He) gas bubble superlattices in molybdenum (Mo) under krypton (Kr) ion irradiation and thermal annealing has been investigated. The He gas bubble superlattices gradually become disordered under Kr ion irradiation at 300° C, and the order-disorder transformation process completes at 2.5 dpa. Both transmission electron microscopy (TEM) and synchrotron-based small-angle X-ray scattering (SAXS) reveal that the order-disorder transformation of He gas bubble superlattices is associated with a slight increase in the average bubble size. Phase-field modeling indicates that the inhomogeneous growth and coarsening of bubbles/voids cause the disordering of imperfect superlattices under irradiation and implies that highly ordered superlattices could potentially exhibit much stronger resistance to irradiation damage. Under thermal annealing, the He gas bubble superlattices in Mo become unstable and disordered at 1000° C with the bubble size increasing from ~1.1 to ~1.6 nm. The finding in this research provides insights into the disordering mechanisms of defect superlattices as well as guidance for designing stable defect superlattices in harsh environments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Electrochemical behavior and separation of iodide in molten LiF-NaF-KF melt

This work studied the electrochemical behavior of iodide in molten LiF-NaF-KF mixture and the separation of iodide from the molten salt at 973 K using a graphite working electrode. The cyclic voltammetry (CV) and chronoamperometry (CA) measurements indicated an anodic passivation layer was formed on the graphite electrode in this melt and the layer blocked the charge transfer across the electrolyte/electrode interface. However, the added I- ions could pass through the passivation layer and were oxidized at the graphite electrode. The characterization of the obtained products proved that iodide ions was efficiently oxidized to I2 gas during electrolysis. Furthermore, the graphite anode showed excellent stability without any obvious change in dimensions after electrolysis, which showed the high current efficiency of I2 evolution reaction. Thus, the graphite electrode was possible to be served as an excellent anode to separate other anions (such as Br) from molten fluoride salts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Method for identification of redox control parameters for corrosion mitigation in molten fluoride salts

Structural material corrosion is a significant concern for the development of molten salt-cooled reactors (MSR) and redox control was proposed to mitigate the corrosion. This study presents an efficient approach to identify the partial pressure of F 2 gas for fluorine driven corrosion, the concentration ratios of UF 4 /UF 3 and ZrF 4 /ZrF 2 , and the partial pressure ratio of HF/H 2 needed to limit metal corrosion and its subsequent dissolution in molten fluoride salts. The identification procedure is made by simply using auxiliary axes in Ellingham diagrams. This approach greatly simplifies the optimization of redox control methods in studying the material corrosion in molten salts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Flux Helium Irradiation of Dispersion-Strengthened Tungsten Alloys and Effects of Heavy Metal Impurity Layer Deposition

Tungsten has been chosen as the plasma-facing material (PFM) for the divertor region in ITER and also a candidate PFM for future plasma-burning nuclear fusion reactors. During fusion device operation, PFMs will be exposed to low-energy He irradiation at high temperatures, resulting in sub-surface bubbles and surface morphology changes such as pores and fuzz. Carbide dispersion-strengthened W materials may enhance the ductility of W, but their behavior under high flux He irradiation remains unclear. In this work, the response of dispersion-strengthened tungsten materials to high flux, low energy He irradiation at high temperature is examined. Tungsten alloyed with 1, 5, or 10 wt. % tantalum carbide or titanium carbide exposed to these conditions result in surface pores, coral-like feature growth and sub-surface helium bubbles. Reactor-relevant helium irradiation (5 x 10 26 m -2 fluence) combined with high powered laser pulses to simulate off-normal reactor events does not significantly alter the surface morphology, as the surface nanostructures appear stable and cracks are only observed on a localized region of one sample. However, specimens show the development of an impurity layer on the surface, likely impurity deposition from the sample holder during irradiation, resulting in a mixed material layer on the surface. Helium bubbles exist in this impurity layer, and obscure conclusions about helium interactions with the carbide dispersoids. Nonetheless, it is clear that the dispersoid microstructure limits He bubble formation and subsequent surface nanostructuring, attributed to the dispersoid composition.

36 MATERIALS SCIENCE↗