Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “programming systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Convolution Correction Factor Adjustments on Static PRA Models for Event Assessment

Current probabilistic risk assessment (PRA) models will contain cut sets that have time-constrained basic events such as switched components, recovery of failed components, and failures in time. For these cut sets that have multiple time-constrained events that interact (e.g., offsite power recover at the same time as multiple diesel generators fail to run), there is the possibility that the minimal cut set quantified result is too large. Since current PRA models typically assume that the accident scenario starts at “time zero,” the fails-to-run basic events use this starting time as the basis for their respective reliability models. Over time, the standard practice was to recognize this issue and accept it as part of the conservatism built into the event tree/fault tree PRA models. However, now that these same PRA models are being used in a regulatory forum, this conservatism needs to be addressed. Further, this issue exists not only for the baseline PRA results, but for deficiencies that have been observed or those that have the potential of occurrence, whether the deficiency is complete failure or just a degraded condition. We have found that this conservatism becomes very important when evaluating scenarios such as station blackout sequences and other loss of offsite power sequences. This paper will address the theory and implemented process used by the Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) PRA software. Starting with SAPHIRE version 8, the process that was developed is to calculate a “convolution correction factor” based on three distinct calculations. The first calculation is the cut set based frequency calculated via the standard event tree/fault tree PRA model (assuming all run failures start at time equal to zero). The second calculation is to perform the exact time-constrained calculation by integrating the component failure models over the time period of interest (e.g., time to recover, a mission time). For example, this exact calculation for the case of the diesel generators is to convolve their failure models with the offsite power recovery model to obtain the exact frequency. The third calculation is to produce the convolution correction factor by dividing the exact frequency calculation by the standard cut set frequency. This convolution correction factor is then applied to the PRA cut sets in order to remove the time-constrained conservatism. The process used to obtain the convolution correction factor for the baseline PRA is important; however, in this paper we also describe what happens when there is degradation of a component or a potential deficiency. These issues become very important in order to ensure that the convolution correction factor is re-calculated correctly. If the correction factor does not get re-calculated and the same baseline convolution correction factor is used, the final analysis result could be over conservative or under conservative. This paper will discuss how these issues are addressed and provide examples on how SAPHIRE automatically makes the necessary adjustments. MathCad verification results can be computed using the provided equations and input data.

99 GENERAL AND MISCELLANEOUS↗

Re-establishment of Light-Weight Radioisotope Heater Unit Platinum-30% Rhodium Alloy Components Production at Oak Ridge National Laboratory

During FY2018 the Oak Ridge National Laboratory (ORNL) Radioisotope Power Systems (RPS) Program completed re-establishment of capability to produce platinum-30% rhodium (Pt-30Rh) alloy components for the Light Weight Radioisotope Heater Unit (LWRHU) Program. These components were last produced at Mound Laboratory in the mid/late-1990s for the National Aeronautics and Space Administration (NASA) Cassini mission. The LWRHU Pt-30Rh Clad Body Subassembly and component fabrication operations are being performed in the iridium alloy Clad Vent Set (CVS) production area at ORNL. Existing equipment (furnaces, electron beam welders, presses, inspection, etc.) are being utilized along with new equipment (two lathes and laser marker) that were purchased for this work. ORNL purchased and qualified an initial quantity of starting materials (Pt powder, Pt-30Rh foil, sheet, and tubing). Equipment, tooling, and materials were procured/fabricated and qualified. Drawings and specifications were updated/modified/developed to the ORNL RPS Program format. Procedures were developed and qualified. All drawings, specifications, and procedures were reviewed/approved by the Idaho National Laboratory (INL) RPS Lead Lab Document Configuration Control Board (DCCB). The dimensional inspection operations and special processes (cleaning, heat treating, sintering, dye penetrant inspection, leak testing, and welding) were successfully qualified and documented. This paper will discuss the process of re-establishing LWRHU production at ORNL to provide for future NASA space exploration science mission needs10.

Veach Jr, Rex↗

Network support for system initiated checkpoints

A system, method and computer program product for supporting system initiated checkpoints in parallel computing systems. The system and method generates selective control signals to perform checkpointing of system related data in presence of messaging activity associated with a user application running at the node. The checkpointing is initiated by the system such that checkpoint data of a plurality of network nodes may be obtained even in the presence of user applications running on highly parallel computers that include ongoing user messaging activity.

Chen, Dong↗

The Department of Energy Savannah River Operations Office Savannah River National Laboratory Unmanned Aircraft System Aviation Implementation Plan

The Department of Energy Savannah River Operations Office Savannah River National Laboratory Unmanned Aircraft System Aviation Implementation Plan was written to provide guidance for the safe, efficient, and lawful operation of the SRNL small Unmanned Aircraft System (sUAS) Program. It shall be the intent of every sUAS remote pilot in command to make reasonable effort not to invade a person's reasonable expectation of privacy when operating the sUAS. SRS sUAS operations will be conducted in accordance all applicable Federal Aviation Administration (FAA), Department of Energy (DOE), and DOE-Savannah River Operations Office (DOE-SR) regulations, policies and procedures. All sUAS operations will be conducted in accordance with the applicable FAA issued DOE Certificate of Authorization (COA) and be approved by the applicable DOE-SR Flight Readiness Review Board (FRRB). The scope of this document is limited to remote pilots in command of sUAS's in support of the DOE, DOE-SR, or SRS missions, research & development (R&D) and national security strategic initiatives supported by SRNL, and other approved missions as required in the US National Airspace (NAS) as defined by the FAA.

99 GENERAL AND MISCELLANEOUS↗

Measuring Fundamental Improvements in Sustainable Urban Mobility: The Mobility-Energy Productivity Metric: Preprint

Recent technological advancements in mobility are creating many options for connecting citizens with employment, goods, and services, particularly in urban areas where modes such as bike and car shares, electric scooters, ridesourcing, and ridesharing are proliferating at a rapid pace. Analysis and tools for overall transportation planning are dominated by urban regional travel demand models whose roots in highway operations poorly reflect the system dynamics in denser areas where parking costs, convenience, and availability - not to mention sustainability concerns and quality of life - are driving people to an ever-greater spectrum of mobility services. In this paper, we present a new paradigm for evaluating mobility options within an urban area. First developed for the U.S. Department of Energy's Energy Efficient Mobility System research program, this metric is termed the Mobility-Energy Productivity (MEP) metric. At its heart, the MEP metric measures accessibility and appropriately weights it with travel time, cost, and energy of modes that provide access to opportunities in any given location. The proposed metric is versatile in that it can be computed from readily available data sources or derived from outputs of regional travel demand models. End times associated with parking, curb access, cost, and reliability and frequency of service need to be carefully considered to obtain an appropriate and accurate perspective when computing the metric. Ultimately, the MEP metric can be used to reflect the impacts of new mobility technologies (transportation network companies, electric scooters), business models (car shares and bike shares), and land-use practices (such as transit-oriented development) on sustainable urban mobility. This paper lays out the need, requirements, and framework for this new metric, and offers it, in collaboration with the American Society for Civil Engineers (ASCE), as a foundational metric for Smart City assessment.

30 DIRECT ENERGY CONVERSION↗

Assessment of Cladding-Cladding Delamination Failures in U-Mo Fuel Plates

Monolithic fuel is a candidate fuel form for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo alloy-based fuel in a monolithic form that is sandwiched between zirconium diffusion barriers and encapsulated in an aluminum cladding. To qualify this fuel system, the program must demonstrate that the fuel meets the safety standards, has a predictable behavior, and performs well in a reactor. Although many plates have shown satisfactory thermo-mechanical performance in reactor, a small number of experimental plates exhibited failures, rendering performance of these plates unacceptable. Post-irradiation examinations of failed plates have revealed that various failures modes are present, including pillowing, blistering, buckling, warping, delamination, fracture, rupture, oxide spallation, etc. Previous studies have implied that such various operational and loading conditions could generate a complex stress-strain state, facilitating distinct failure modes that could impact the structural integrity. To understand such various failure modes, a comprehensive set of studies focusing on failure modes is being performed. As a part of these studies, this work studies the cladding-cladding separation failures that were observed in some of previous irradiation tests. To understand the root cause of cladding separation failures, selected plates from previous irradiation experiments were simulated under comparable operational conditions. Stress-strain state of the plates at the interface were examined. The results were comparatively evaluated to understand possible effects of stress state of the bond-line on delamination failures. This paper presents these findings, discusses such failure modes, and examines the influence of various factors on previously observed cladding delamination failures.

42 ENGINEERING↗

INL Operations Improvements of Nuclear Enabled Missions for NASA - Presentation

The Idaho National laboratory (INL) has supported NASA missions integrate nuclear power systems since the Department of Energy (DOE) moved the Radioisotope Power Systems (RPS) program in 2002 from Mound, Ohio to the Materials and Fuels Complex, INL (Argonne National Laboratory West (ANL-W) prior to 2005). This paper discusses the evolution of INL operations improvements made at INL and KSC throughout the Mars Exploratory Rovers, New Horizons, Mars Science Laboratory, and Mars 2020 missions.

99 GENERAL AND MISCELLANEOUS↗

Electrical Substation Configuration Effect on Substation Reliability

It is crucial that the U.S. electrical grid be reliable, due to its critical role in the economy and our national defense/security. Many common tasks and industrial operations rely on proper electrical power distribution. In designing new bus systems or evaluating existing ones, the type of configuration employed affects the level of risk, reliability, maintenance, and cost involved. The present work utilizes Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) to perform a probabilistic risk assessment (PRA)-based sensitivity study on substation reliability in regard to different bus configurations. This study examines single bus, main and transfer, breaker and a half, double bus/double breaker, and ring bus configurations applied to busses with different numbers of lines. The case variances, methods, and rankings presented herein can help guide bus configurations for electrical grid design/analysis in the future.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Electrical Substation Configuration Effect on Substation Reliability

The nation’s electrical grid must be reliable because of its critical role in the economy, defense, and security of the nation. Many common tasks and industrial operations rely on proper electrical power distribution. In the design of new bus systems or evaluation of existing bus systems, the type of bus configuration affects the risk, reliability, maintenance, and cost of the system. This work utilizes Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) to perform a probabilistic risk assessment (PRA) based sensitivity study on the reliability of substations with differing bus configurations. This study examines single bus, main and transfer, breaker and a half, double bus/double breaker, and ring bus configurations applied to busses of varying number of lines. The case variances, methods, and rankings presented can provide a guide for bus configuration for future electrical grid design and analysis.

24 POWER TRANSMISSION AND DISTRIBUTION↗

SRS Defense Waste Processing Facility - the Nation's Only Operating Vitrification Facility - Completes 20 Years of Radioactive Operations - 17407

Savannah River Remediation (SRR) is the current Liquid Waste contractor at the U.S. Department of Energy's (DOE) Savannah River Site (SRS), located near Aiken, South Carolina, and operates the Defense Waste Processing Facility (DWPF), along with the other SRS liquid waste facilities. The DWPF, the nation's only operating vitrification facility, completed 20 years of radioactive operations in 2016. During this period, DWPF has safely treated the high-level liquid waste at this DOE facility since radioactive operations began with the first transfer of sludge waste feed to DWPF on March 12, 1996. A little over a month later, on April 29, 1996, the first radioactive canister was poured. DWPF poured its 4,000. canister of vitrified waste on December 31, 2015. As of September 30, 2016, DWPF has removed approximately 59.9 million curies from the liquid waste system at SRS and placed them in 4,106 canisters. SRS has operationally closed 8 high-level waste tanks. The DWPF melter has poured nearly 7.14 million kg of molten glass, and the facility has used only two melters in its lifetime. Melter 1 poured 1,339 canisters (1996-2002), while melter 2 to date (September 30, 2016) has poured 2,767 canisters (2003-present). Melter 2 continues to safely and efficiently operate. In order to achieve these accomplishments, the facility has chronicled a history of continued operational improvements such as the installation of bubblers in the melter to increase production, incorporation of glass compositions to achieve higher waste loadings, and improvements to melter design to extend melter life. As SRR moves forward to the next 20 years, continued improvements as well as maintaining the aging infrastructure through a proactive system health program are key priorities. This paper chronicles 20 years of challenges, improvements and accomplishments, and discusses future operations and infrastructure upgrades including implementation of a key flowsheet change to significantly reduce hydrogen generation in the Chemical Process Cell. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Criticality safety control of fuel debris produced by the accident of Fukushima Daiichi nuclear power plants - technical development in Japan from 2012 and the future

Full text of publication follows: On 11 March 2011, Japan was attacked by the '2011 off the Pacific coast of Tohoku Earthquake'. It was the greatest earthquake ever recorded around Japan. It caused big tsunami and it also attacked Tohoku sea coast area severely and violently. Approximately 16,000 people passed away and still about 2,600 people are lost by the earthquake and the tsunami. This extraordinary natural disaster affected the society of Japan deeply. But more serious problem is the severe accident occurred in Fukushima Daiichi Nuclear Power Plants (1FNPP) after the earthquake and tsunami attack. By the tsunami after the earthquake, because of loss of ultimate heat sink (LUHS), three reactors of 1FNPP were damaged and the intact fuel became fuel debris. After the accident, Government of Japan setup the council for the decommissioning of TEPCO's Fukushima Daiichi Nuclear Power Plant and it released the general plan for countermeasure of the severe accident occurred in Japan, i.e. 'Mid-and-long-Term Road map towards the Decommissioning of Fukushima Daiichi Nuclear Power Units 1-4'. According to the road map, nuclear power reactor vendors and research institutes in Japan have started the national project to carry out the decommissioning activity. International Research Institute for Nuclear Decommissioning (IRID) is the association for technical development for Fukushima site decommissioning. Under this umbrella, nuclear power reactor vendors in Japan, i.e. Toshiba, Hitachi and Mitsubishi, and Japan Atomic Energy Agency (JAEA) have carried out the technical development required for the criticality safety control of the Fukushima fuel debris. Furthermore, JAEA has a plan to use the criticality assembly STACY for obtaining the neutronics characteristics of the fuel debris by modifying STACY from the solution system to heterogeneous system. This program is conducted by entrustment of Nuclear Regulation Authority of Japan, independently from IRID framework. It is expected that it will reach first criticality in FY2018. Researchers in universities in Japan also have own research program to control reactivity of fuel debris. This presentation will summarize the on-going research programs in Japan for the criticality safety control in order to remove and store the fuel debris from Fukushima site. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗