Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lithological”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Gas Release as a Deformation Signal

Radiogenic noble gases are contained in crustal rock at inter and intra granular sites. The gas composition depends on lithology, geologic history, fluid phases, and the aging effect by decay of U, Th, and K. The isotopic signature of noble gases found in rocks is vastly different than that of the atmosphere which is contributed by a variety of sources. When rock is subjected to stress conditions exceeding about half its yield strength, micro-cracks begin to form. As rock deformation progresses a fracture network evolves, releasing trapped noble gases and changing the transport properties to gas migration. Thus, changes in gas emanation and noble gas composition from rocks could be used to infer changes in stress-state and deformation. The purpose of this study has been to evaluate the effect of deformation/strain rate upon noble gas release. Four triaxial experiments were attempted for a strain rate range of %7E10-8 /s (180,000s) to %7E 10-4/s (500s); the three fully successful experiments (at the faster strain rates) imply the following: (1) helium is measurably released for all strain rates during deformation, this release is in amounts 1-2 orders of magnitude greater than that present in the air, and (2) helium gas release increases with decreasing strain rate.

58 GEOSCIENCES↗

Mechanisms for Methane Transport and Hydrate Accumulation in Coarse-Grained Reservoirs

The distribution of natural methane hydrate within high saturation reservoirs and mechanisms that control the migration of methane are an active area of research. In this project, we studied methane migration mechanisms and associated hydrate accumulation rates in coarse-grained sands of the Terrebonne Basin, located in Walker Ridge Block 313 (WR313), northern Gulf of Mexico. Hydrate in this area is distributed heterogeneously within ~900 m of methane hydrate stability zone, in both thick (10-25 m) and thin (< 3 m) sand layers, and in units of subvertical hydrate-filled fractures. We investigated hydrate formation from diffusively and advectively supplied methane using one-, two-, and three-dimensional basin modeling with inputs from well log and seismic data. The hydrate accumulations at WR313 can mostly be explained by short, diffusive migration of methane as well as short-range advective transport of methane from clays into neighboring coarser-grained layers. This is likely enhanced by small-scale lithologic variations, including local microbial methanogenesis in interbedded clays. Furthermore, our work shows overpressure in clay sediments surrounding sand reservoirs may enhance short-range diffusive migration. Long-range migration of dissolved methane and gas mainly influence hydrate saturation right at the base of the hydrate stability zone, although the dissolved phase can be channeled upwards along sands by compaction-driven flow. Capillary effects can allow gas bubbles to migrate appreciable distances above the predicted base of gas hydrate stability, possibly reaching a few tens of meters into the hydrate stability zone. Recycling methane from hydrate buried beneath the base of the hydrate stability zone can concentrate hydrate at large saturations within a few tens of meters of the base of hydrate stability.

58 GEOSCIENCES↗

Global Survey of Selected Deep Underground Facilities; Examples of Geotechnical and Engineering Capabilities, Achievements, Challenges(Mines, Shafts, Tunnels, Boreholes, Sites and Underground Facilities for Nuclear Waste and Physics R&D):A Guide

This report presents tables, references, notes, and a synthesis of some notable geotechnical and engineering information that were applied in the creation of five interactive layer maps [http://gis.inl.gov/globalsites/ will redirect to 2018 update, http://gis.inl.gov/GlobalSurvey/] for selected: 1) deep mines and shafts; 2) existing, considered or planned radioactive waste management deep underground studies or disposal facilities 3) deep large diameter boreholes, 4) physics underground laboratories and facilities, and 5) deep open pit mines from around the world. These data are intended to facilitate user access to basic information and references regarding “deep underground” facilities, history, activities, and plans. In general, the interactive maps and database provide each facility’s approximate site location, geology, and engineered features (e.g.: access, geometry, depth, diameter, year of operations, groundwater, lithology, host unit name and age, basin; operator, management organization, geographic data, nearby cultural features, other). Although the survey is not all encompassing, it is a comprehensive review of many of the significant existing and historical underground facilities discussed in the literature addressing radioactive waste management and deep mined geologic disposal safety systems. The interactive map suite allows for a better appreciation of site area geographic and cultural settings. The global survey is intended to be used as a communication tool to support and inform: 1) interested parties and decision makers; 2) radioactive waste disposal and siting option evaluations, and 3) safety case development applicable to any mined geologic disposal facility as a demonstration (examples) of historical and current engineering and geotechnical capabilities available for use in deep underground facility siting, planning, construction, operations and monitoring.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Assessing rare earth element concentrations in geothermal and oil and gas produced waters: A potential domestic source of strategic mineral commodities (Final Report)

The project team collected and analyzed 224 water samples and 101 matching rock samples. INL's improved method of measuring aqueous REEs allows study of samples previously thought too volume limited to measure. The study found that aqueous REEs occur at trace levels in all analyzed samples, and sometimes exceed ocean REE concentrations by a factor of 1,000. No significant predictive relationship to lithology, reservoir temperature, nor salinity was discovered, but aqueous REE concentration appears spatially controlled. Future work is needed to find the spatially-dependent variable that controls aqueous REE concentration.

15 GEOTHERMAL ENERGY↗

Mid-Atlantic U.S. Offshore Carbon Storage Resource Assessment Project (Final Technical Report)

The greatest potential for carbon storage in the northeastern United States lies in the offshore geologic formations comprising the outer continental shelf (Monteverde et al., 2011). Offshore storage can be linked to large point-sources of carbon dioxide (CO 2 ) while avoiding many of the logistical difficulties and potential risks encountered when siting onshore projects, especially in densely populated areas of the East Coast. Offshore CO 2 storage assessment and research in the United States is underway to address uncertainty in potential storage resources, particularly in the mid- and north-Atlantic offshore area. Given the current knowledge base and access to publicly available data, the objectives of the Mid-Atlantic U.S. Offshore Carbon Storage Resource Assessment Project (MAOCSRAP) were fourfold: (1) complete a systematic carbon storage resource assessment of the mid-Atlantic offshore coastal region from the Georges Bank Basin (GBB) through the Long Island Platform (LIP) to the southern Baltimore Canyon Trough (BCT); (2) define key input parameters to reduce uncertainty for offshore storage resource and efficiency estimates; (3) perform a preliminary assessment of risk factors, uncertainties, and data gaps; and (4) engage industry and regulatory stakeholders through development of a Road Map to assist future project planning and implementation. The MAOCSRAP project has compiled, inventoried, and assimilated various publicly available data sets to provide a strong technical basis on which future carbon storage studies and applications can be built. The knowledge infrastructure necessary to support the development of full-scale offshore carbon storage include: Defining the geologic characteristics of candidate storage sites (Chapter 2). Using existing seismic data to better define the continuity of the storage zones and seals (Chapter 3). Cataloguing the hydrogeologic properties of mid-Atlantic offshore storage sites (Chapter 4). Calculating prospective CO 2 storage resources using net effective pore volumes and fluid displacement properties specific to offshore lithologies (Chapter 5). Examining risk factors related to offshore storage (Chapter 6). Communicating with industry and other stakeholders about the future prospects for offshore storage (Chapter 7). Ensuring technology transfer to industry and other stakeholders (Chapter 8). Led by Battelle, this project was conducted by public and private entities with expertise in offshore geology and resources for the study region, including state geological surveys of Delaware, Maryland, and Pennsylvania; United States Geological Survey-Woods Hole Coastal and Marine Science Center and Haifa University; Rutgers University; Harvard University; and Lamont-Doherty Earth Observatory (LDEO) at Columbia University. The storage resource assessment was completed for a broad region offshore of the U.S. East Coast, from Massachusetts to Virginia. The results include high-level storage resource estimates for areas not previously characterized and improved storage resource estimates for geographically expansive portions of offshore geologic units. Results of the project provide a foundation for developing CO 2 storage along offshore areas of the mid-Atlantic United States. A combination of information was used to provide confidence in project results. Key findings of the major project tasks are summarized as follows. Subsurface Data Analysis: Legacy seismic, well-log, core, and biostratigraphic data were digitized, reprocessed, and analyzed using modern techniques, augmenting previous characterization efforts. The sequence stratigraphic framework for the Cretaceous and Jurassic strata was developed by correlating well-log depositional sequences to seismic reflectors identified in the BCT, LIP, and GBB. The integration of well-log stratigraphy with seismic stratigraphy and petrophysical analysis helped to identify and map potential storage zones within sequences of the Logan Canyon (LC), Missisauga, and Mohawk formations, as well as the regionally extensive caprock comprised of the Dawson Canyon shale. Approximately 4,000 kilometers (km) of seismic data was reprocessed to create a structural framework that was used to tie together all available well data, constrain sequence stratigraphic interpretations, and make regional assessments of offshore carbon storage resources. Prospective storage resource estimates were 150 to 1136 megatons (Mt) for the combined storage zones. This suggests mid-Atlantic U.S. offshore formations can store decades of CO 2 from industrial sources in the region. Preliminary local reservoir simulations suggest that injection rates of 1 Mt CO 2 /year may be sustained for 30 years in single injection wells in the BCT. Advanced geologic modeling and new data acquisition are needed to address data gaps and advance carbon capture and storage (CCS) in key offshore areas selected for further investigation. Offshore Risk Factors: Offshore geologic risk factors include soft sediment deformation, unit continuity, sedimentological and structural features, seismicity and hydrates. CO 2 storage risks include inadequate seals, migration/leakage, and chemical interactions leading to decreased storage. Sensitive habitats, environmental impacts, disturbance to seafloor, and other risks need to be identified in advance of project activities and integrated into detailed mitigation plans for all project phases. Stakeholder Engagement: Input and participation from government, industry, and environmental groups provided input into the Road Map and address next steps needed for project deployment. Early engagement and ongoing communication, as well as policy framework development, is key to large-scale deployment of CCS. Next Steps: This project represents an important first step by completing a high-level CO 2 storage resource assessment and building the knowledge infrastructure necessary to improve quantitative storage resource estimates. The data sets that have been curated under this project provide an opportunity to conduct research and development (R&D) needed to address data gaps and reduce risk and uncertainty. Offshore characterization and validation strategies that are systematically designed to provide data and infrastructure that can be upscaled to meet commercial requirements could be developed off of this foundation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Integrated characterization of CO 2 storage reservoirs on the Rock Springs Uplift combining geomechanics, geochemistry, and flow modeling

This project improves understanding of the effects CO 2 injection and storage on geomechanical, petrophysical, and other properties on two potential reservoirs, the Madison Limestone and Weber Sandstone, at the Rock Springs Uplift, southwest Wyoming. Rock physics studies, laboratory experiments, and computer simulations were employed. Two groups of rock samples were prepared, one aged with formation brine and the second aged with CO 2 -saturated formation brine and subsequently used for geomechanical, geochemical, and petrophysical testing. Rock physics studies provided a facies classification to discriminate among different lithologies and to investigate the feasibility of predicting petrophysical properties using seismic inversion. By applying a zone-wise regression relation established in this facies analysis, a 3D reservoir model was developed. It was determined that time-lapse seismic data are not feasible for monitoring CO 2 displacement at the Rock Springs Uplift or to mitigate leakage-risks situations because pressure and fluid saturation have small effects on elastic velocities and synthetic seismograms. The small variations that do occur are due to the low porosity of the sandstone and the high stiffness of the dolomite. In the Madison Limestone, mineral dissolution due to reaction with CO 2 -saturated brine was observed in highly permeable pathways while mineral precipitation happened in intergranular or micropores. Changes in pore size were quantified via Time-Domain Nuclear Magnetic Resonance transverse relaxation time (T 2 ) and diffusion coefficient distributions. As opposed to continuous injection of CO 2 -saturated brine, a subtle increase in porosity after static ‘soaking’ with CO 2 -saturated brine increases permeability due to the heterogeneity of changes in pore and pore throat sizes. Porosity-permeability relationships are fitted using a power-law function that can be adopted to model time-evolved porosity and permeability in a transport-limited CO 2 injection process. The effect of CO 2 -saturated brine on the linear elastic properties of Weber Sandstone and Madison Limestone cannot be generally concluded. Considering horizontal and vertical orientations and different confining pressures, no consistent relationship between stress (or strain) data and reaction with CO 2 -saturated brine was observed in the nonlinear plastic and post-failure regime. The change of elastic constants due to reaction with CO 2 -saturated brine is more significant in Madison Limestone than in Weber Sandstone; however, no consistent trend was observed. Reservoir simulations suggest that injectivity for Weber Sandstone is adversely impacted by low permeability. Changes in confining pressure do not impact injection rate and can be ignored while the effect of changes to pore pressure cannot. The effect of confining pressure and pore pressure on the size of the CO 2 plume in the Madison Limestone is negligible because of higher permeability. Geomechanical and petrophysical properties induced by CO 2 -brine-rock reactions were time-dependent. Simulations considered these time-dependent properties and indicate that injectivity, porosity distribution, pressure distribution and CO 2 saturation were affected.

58 GEOSCIENCES↗

Geothermal Deep Direct Use for Turbine Inlet Cooling in East Texas

The National Renewable Energy Laboratory (NREL), the Southern Methodist University Geothermal Laboratory (SMU), Eastman Chemical (Longview, TX), and TAS (Houston, TX) evaluated the feasibility of using geothermal heat to improve the performance of a natural-gas power plant in East Texas. The area of interest is the Eastman Chemical plant in Longview, Texas, which is on the northwestern margin of a geologic region known as the Sabine Uplift. The feasibility study focused on determining the potential for accessing a subsurface hot-water geothermal resource within a 10-km radius of the site to provide thermal energy for absorption chillers. Wells within a 20-km radius are included for broader geological comparison to determine the heat flow, temperature-at-depth, field porosity and permeability. The lithologies of most interest are the Lower Cretaceous Trinity Group and Upper Jurassic Cotton Valley Group. The deeper Cotton Valley formations are hotter (averaging 117 to 130°C), yet permeability and porosity are low. The shallower Trinity Group contains more variability in permeability and porosity and lower temperatures averaging about 98 to 117°C. The shallower formations are considered despite the lower temperature because of increased ability to produce larger volumes of water and extract enough heat before reinjection. The complete SMU analysis is available in the National Geothermal Data System (NGDS). Tapping such deep geothermal sources for direct heating (as opposed to power generation) is known as geothermal deep direct use (DDU). Geothermal DDU has potential across a wide swath of the United States but is underutilized due to challenging project economics associated with developing a deep geothermal resource for what are typically small-scale, variable-demand projects. This project examines the feasibility of geothermal energy integration in a natural-gas combined cycle power station in East Texas. The DDU resource is tapped to drive absorption chillers (24/7) for production of chilled water at 5-10°C (41-50°F). This chilled water is stored until needed, which allows for continuous operation with a relatively small-capacity geothermal/absorption chiller system. When conditions are favorable, the chilled water is dispatched to cool the air entering the compressor stage of a gas combustion turbine. This process, known as turbine inlet cooling (TIC), boosts power production during periods of high temperature and high-power demand. Such systems can enhance grid reliability and reduce the cost for peak-demand power. A simulation model of the power plant was developed in IPSEpro software and validated against operational data from the plant. This model allowed the team to estimate the additional power that could be produced by applying TIC under different operating and ambient conditions. Absorption chiller performance was estimated from vendor sources to determine the production rate of chilled water from the geothermal resource. Geothermal drilling and development costs were estimated using NREL's GEOPHIRES 2.0. The expected lower drilling costs in this region led to an estimated cost of geothermal heat of about $4/MMBtu (1.4 cents/kWh t ). The estimated cost for the absorption chillers and TIC hardware were obtained from literature sources and project partners. Hourly data were obtained for weather, natural gas and electricity prices, and plant operating state for 2017, which served as a representative year. NREL estimated the capital cost, operating cost, and additional electricity production and revenue for different combinations of geothermal capacity, chiller capacity, and water storage-tank size. The analysis drove toward smaller geothermal and chiller systems to reduce equipment cost. A relatively low-cost water storage tank accumulated the near-continuous chilled water output for later use when TIC was most valued.

15 GEOTHERMAL ENERGY↗

Real Time Degassing of Rock during Deformation

An experimental system we developed combines triaxial rock deformation and mass spectrometry to measure noble gas flow before, during, and after rock fracture. Geogenic noble gas is released during triaxial deformation (real time) and is related to volume strain and acoustic emissions. The noble gas release then represents a signal of deformation during its stages of development. Noble gases are contained in most crustal rock at inter and intra granular sites. Their release during natural and man-made stress and strain changes represents a signal of deformation in brittle and semi-brittle conditions. The noble gas composition depends on lithology, geologic history, age of the rock, and fluids present. Uranium, thorium and potassium-40 concentrations in the rocks also affect the production of radiogenic noble gases (4He, Ar). Noble gas emission and its relationship to crustal processes have been studied for many years in the geologic community including correlations to tectonic velocities and qualitative estimates of deep permeability from surface measurements, finger prints of nuclear weapon detonation, and as a potential precursory signal to earthquakes attributed to gas release due to pre-seismic stress, dilatancy and/or fracturing of the rock. Helium emission has been shown as a precursor of volcanic activity. We present empirical results/relationships of specimen strain, microstructural evolution, acoustic emissions, and noble gas release from laboratory triaxial experiments performed upon a granite and a young basalt, bedded salt, and a marine shale.

58 GEOSCIENCES↗

Potential Formation Damage: An Integrated Reservoir Characterization Study of the Naturally Fractured Carbonate Middle Duperow Formation at the Kevin Dome, Montana

In this study, we integrate geologic and engineering data of a naturally fractured carbonate reservoir at the Kevin Dome, Montana. Well test data are correlated with core description, geochemical and lithology study to determine the flow behavior and communication within the injection test interval and to the surrounding area. Based on a dual-continuum geologic model, numerical brine injection simulations are carried out to validate the interpretation results from our well test analytical models and forecast the probability of CO 2 injection success using current reservoir properties. As a result, our well test analytical models as well as lithology/core description suggest that fluid flow may be mainly restricted to the injection interval and the assumption of radial (horizontal) flow may be appropriate. The well test models also indicate that there is potentially formation damage with a positive skin factor although prior to brine injection well tests, well stimulation through acid treatment was performed. Our numerical simulation results appear to confirm this formation damage by showing additional pressure buildup in the injection data during later test periods. To explain this, acid may have dissolved dolomite then dolomite or calcite may have been formed again further into the matrix/fracture system. Another possible explanation is mechanical clogging of the fractures due to acid dissolving dolomite and dislodging fine grains. Our work also predicts that if no additional well stimulation is performed, the project will have a lower probability of successfully injecting 1 million tons of CO 2 into the Middle Duperow formation over 4 years.

42 ENGINEERING↗

High-frequency and Vertical Variations of Soil Moisture and their Impact on Ecosystem Dynamics

The vertical distribution of subsurface moisture is a major control on ecosystem dynamics and climate. The Mediterranean climate of California, with wet winters and dry summers, provides a testbed for understanding how transpiration is sustained through extended dry periods. The project developed and tested a new subsurface hydrology model that includes a parameterization of stochastic hydraulic conductivity to capture fracture flow, a diagnostic model of rooting profile that depends on the subsurface hydrology, and a representation of hydraulic redistribution by plant roots. A sensitivity study shows that it is plants with rooting depths >8 m that could access the subsurface moisture. The insight is applied to understand differential tree mortality during the 2012-2016 drought in California. The analysis shows that greater mortality trees on plutonic rocks than on sedimentary rocks. The study demonstrates, for the first time, the importance of lithology for the distribution and health of ecosystems.

54 ENVIRONMENTAL SCIENCES↗

X-ray Computed Tomography on UNESE Core: FY2020 Data Report to Support Fracture and Multiphase Fluid Flow Studies

Natural and induced fractures are potential preferential pathways for migration of radioactive gases to earths surface from underground nuclear explosions (UNEs). This report documents X-ray computed tomography (XRCT) imaging on 26 samples of rock core that was collected to support the Underground Nuclear Explosion Signatures Experiment (UNESE) program. The XRCT datasets are intended to help fill a data gap on the three-dimensional (3D) characteristics of natural and/or induced fractures at the centimeter and smaller scale, which may strongly influence multiphase fluid flow and transport properties of preferential flow paths and interaction with the matrix of the surrounding host rock. Pre- and post-UNE rock samples were carefully chosen to enable comparison of fractures as a function of lithologic and petrophysical properties, as well as distance to the past UNEs. This report serves as documentation for the data, including an introduction with the research motivation, a methods and materials section, descriptions of the XRCT datasets without post-processing, and recommendations for 3D quantification via image analysis and digital rock physics.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Installation of Lysimeters Near Engineered Trench 3

Three new lysimeter stations were installed on the north rim of Engineered Trench 3 (Figure ES-1)at the E-Area Low Level Waste Facility (ELLWF). These stations were designated as ET3-VL-3, ET3-VL-4, and ET3-VL-5. The stations were installed in a line with the two existing stations (ET3-VL-1 and ET3-VL-2) and spaced approximately 100 ft apart. Two lysimeters were installed at each station at the depths shown in Table ES-1. Lysimeter placement was based on borehole lithology and was comparable to the existing lysimeter stations. The deepest lysimeter at each of the three new lysimeter stations was designated as the action-level lysimeter.Following installation, the lysimeters were purged and placed under vacuum for sampling. Sampling occurred in December 2020 with each lysimeter producing 1000 ml of water for tritium analysis. All lysimeters were below the administrative limit for ET3 (43.7 pCi/ml) with all but ET3-VL-5 (222) at background levels. ET3-VL-5 (222) had a tritium concentration of 27.5 pCi/ml.With the addition of the new lysimeters at ET3, the vadose zone monitoring system is now comprised of 309 active lysimeters at 102 lysimeter stations. There are 93 action-level lysimeters at 102 stations

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Assessment of Enhanced Oil Recovery Using Carbon Dioxide in Michigan Basin Silurian Pinnacle Reefs

The Midwest Regional Carbon Sequestration Partnership (MRCSP) has incorporated the work of geologic research teams (Geoteams) in its regional characterization, project planning and carbon dioxide (CO 2 ) injection implementation work since the partnership was established by the U.S. Department of Energy (DOE) in 2003. Over this 16-year period, the cohort of Geoteams has grown from five to ten states and has contributed to the characterization of geologic sequestration opportunities, refinement of reservoir and seal data, and supported injection efforts through both predictive and post-injection assessments. The Michigan team at Western Michigan University has provided technical analysis and support of the enhanced oil recovery (EOR) using carbon dioxide (CO 2 ) in the Northern Michigan Silurian Pinnacle reefs. With Core Energy, LLC as the industry partner, this project has assessed the potential for EOR in known fields in the Michigan Pinnacle reefs and the capacity for CO2 storage in the reef reservoirs as they are depleted and after reservoir abandonment. This project managed by Core Energy, LLC, involves the only commercial CO 2 Enhanced Oil Recovery floods within the MRCSP region. The Silurian pinnacle reef trend shows significant potential for CO 2 -EOR: this play is relatively new, with approximately 60% of the wells in the largest Niagaran fields still accessible. Most wells have modern logs and there are many cores, core analyses, pressure tests and produced water analyses available for study from these fields. These carbonate reservoirs in Michigan have produced sufficient oil to warrant evaluation for additional recovery efforts. The role of the Michigan team was to collect and analyze all relevant data about reservoir properties, including lithologic and depositional characteristics of the reservoir formations and porosity and fluid flow properties through different compartments in the reservoir. The team has also developed models that represent the geological and physical characteristics of the reservoir and seal system.

01 COAL, LIGNITE, AND PEAT↗

Pulsed Neutron Capture for Monitoring CO 2 Storage with Enhanced Oil Recovery in Northern Michigan

The Midwest Regional Carbon Sequestration Partnership (MRCSP) was founded in 2003 as part of the U.S. Department of Energy’s (DOE’s) Regional Carbon Sequestration Partnership initiative. Since its founding, MRCSP has made significant strides toward making CCUS a viable option for states in the region. The public/private consortium, funded through the DOE Regional Carbon Sequestration Initiative, brings together nearly 40 industry partners and 10 states. Battelle, as the project lead, oversees research, development and operations and coordinates activities among the partners. The incremental, phased approach has built a valuable knowledge base for the industry and paved the way for commercial-scale adoption of CCUS technologies. From 2008 to 2020, MRCSP Phase III focused on the development of large-scale injection projects. This report is part of a series of reports prepared under the Midwestern Regional Carbon Sequestration Partnership (MRCSP) Phase III (Development Phase). These reports summarize and detail the findings of the work conducted under the Phase III project. Pulsed neutron capture (PNC) logging has been used as part of the MRCSP monitoring of CO 2 injection and storage during assessment of enhanced oil recovery (EOR) in several Northern Niagara Pinnacle Reef Trend (NNPRT) reefs in Michigan. This technique and data processing cost less than traditional fluid sampling and presents a low risk to well operations by utilizing through-tubing logging capabilities. Additionally, monitoring CO 2 migration and break-through can be conducted from a single monitoring well in the reservoir. A total of four reefs were selected for these studies to monitor CO 2 migration and to test the viability and effectiveness of the PNC technology for saturation monitoring in a low porosity and highly diverse lithology environment. This study provides assessment of the technology and recommendations for utilization of saturation analysis.

01 COAL, LIGNITE, AND PEAT↗

Western Sector In-Situ Chemical Oxidation Project: Additional Injection Pilot Testing Supplemental Results (U)

Trichloroethylene (TCE) and tetrachloroethylene (PCE) are persistent at elevated concentrations in the Western Sector of the M-Area Hazardous Waste Management Facility (HWMF) groundwater plume. Migration of these chlorinated ethenes as Dense Non-Aqueous Phase Liquids (DNAPLs) occurred from the M-Area Settling Basin along geologic strata resulting in a high concentration groundwater plume in Western Sector. Pump-and-treat has been active for over 30 years at the M-Area HWMF to hydraulically contain the primary sources of the plume in addition to other remediation strategies throughout the contaminated zone, like soil vapor extraction, dynamic underground stripping, groundwater recirculation wells, and bioremediation. In-situ chemical oxidation (ISCO) has been identified as a viable treatment method for removal of these volatile organic compounds (VOCs) due to the complex lithology and high concentrations in this part of the aquifer. In addition to ISCO, a new recovery well (i.e., RWM018) was also installed in Western Sector to contain the high concentration VOC plume. The ISCO projects have utilized the gradient induced by RWM018 to help plan the injection and monitoring locations. The combination of ISCO and the additional pump and treat in Western Sector with the installation of RWM018 will help to control the plume and maximize remediation efforts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Computed Tomography Scanning and Geophysical Measurements of the Caney Shale Formation from the Tomaney #1-35-34-27 Well

Evaluation of reservoir samples can support resource estimation and determination of effective extraction methodologies. While it is common for commercial entities to perform these characterizations, the resources necessary to conduct these analyses are not always available to the broader interest base, such as state agencies, universities, and research-based consortiums. To meet the growing need for comprehensive and high-quality lithologic data for collaborative research initiatives, the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) has used available resources in conjunction with previous techniques and new, innovative methodologies to develop a systematic approach for the evaluation of cores. This report focuses on the Tomaney #1-35-34-27 well. Tomaney #1-35-34-27 was drilled in southwestern Stephens County, Oklahoma within section 35, township 2S, and range 4W. The Tomaney #1-35-34-27 was drilled in January/February of 2020 and targeted the Devonian Woodford Shale Formation and cored the Mississippian Caney Shale formation within the Ardmore Basin.

04 OIL SHALES AND TAR SANDS↗

Mixing Cell Model: A One-Dimensional Numerical Model for Assessment of Water Flow and Contaminant Transport in the Unsaturated Zone

This report describes the Mixing Cell Model code, a one dimensional model for water flow and solute transport in the unsaturated zone under steady state or transient flow conditions. The model is based on the principles and assumptions underlying mixing-cell model formulations. The unsaturated zone is discretized into a series of independent mixing cells. Each cell may have unique hydrologic, lithologic, and sorptive properties. Ordinary differential equations describe the material (water and solute) balance within each cell. Water-flow equations are derived from the continuity equation, assuming that unit gradient conditions exist at all times in each cell. Pressure gradients are considered implicitly through model discretization. Unsaturated hydraulic conductivity and moisture contents are determined by the material specific moisture-characteristic curves. Solute-transport processes include explicit treatment of advective processes, first order chain decay, and linear sorption reactions. Dispersion is addressed through implicit and explicit dispersion. Implicit dispersion is an inherent feature of all mixing-cell models and originates from the formulation of the problem in terms of mass balance around fully mixed volume elements. Expressions are provided that relate implicit dispersion to the physical dispersion of the system. Two FORTRAN codes were developed to solve the water flow and solute-transport equations: (1) the Mixing Cell Model for Flow (MCMF) solves transient water-flow problems and (2) the Mixing Cell Model for Transport (MCMT) solves the solute-transport problem. The transient water-flow problem is typically solved first by estimating the water flux through each cell in the model domain as a function of time using the MCMF code. These data are stored in either ASCII or binary files that are later read by the solute transport code (MCMT). Code output includes solute pore water concentrations, water and solute inventories in each cell and at each specified output time, and water and solute fluxes through each cell and specified output time. Computer run times for coupled transient water flow and solute transport were typically several seconds on a 2 GHz Intel Pentium IV desktop computer. The model was benchmarked against analytical solutions and finite element approximations to the partial differential equations (PDE) describing unsaturated flow and transport. Differences between the maximum solute flux estimated by the mixing cell model and the PDE models were typically less than two percent. This revision includes an option for a fixed concentration lower boundary condition for diffusive fluxes for versions 020321 and later.

54 ENVIRONMENTAL SCIENCES↗

Data Report: UT-GOM2-1 Sediment Grain Size Measurements at Site GC 955, Holes H002 and H005

Sediment grain size measurement in marine sediments provides a record of the stratigraphic variation in grain size and thus energy regime at the time of deposition. In addition to the grain size distribution, the degree of sediment sorting can also be calculated, and together they both influence primary sediment porosity and permeability. Here we present sediment grain size results from laser diffraction particle size analysis of samples from pressure cores collected during the 2017 UT GOM2-1 Expedition. We measured both bulk sediment and organic carbon-free sediment fractions for 46 samples and organic carbon-free sediment for 5 samples at Site GC 955, Holes H002 and H005. Differences between the bulk sediment and organic carbon-free fractions reflect the relative amount and size fraction of the organic carbon. The sample results presented here represent the grain size variation of the host lithology across the Green Canyon (GC) 955 gas hydrate reservoir.

03 NATURAL GAS↗