Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “large area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Performance of large area xenon ion thrusters for orbit transfer missions

Studies have indicated that xenon ion propulsion systems can enable the use of smaller Earth-launch vehicles for satellite placement which results in significant cost savings. These analyses have assumed the availability of advanced, high power ion thrusters operating at about 10 kW or higher. A program was initiated to explore the viability of operating 50 cm diameter ion thrusters at this power level. Operation with several discharge chamber and ion extraction grid set combinations has been demonstrated and data were obtained at power levels to 16 kW. Fifty cm diameter thrusters using state of the art 30 cm diameter grids or advanced technology 50 cm diameter grids allow discharge power and beam current densities commensurate with long life at power levels up to 10 kW. In addition, 50 cm diameter thrusters are shown to have the potential for growth in thrust and power levels beyond 10 KW.

Rawlin, Vincent K.↗
NASA NTRS1989

Mapping small elevation changes over large areas - Differential radar interferometry

A technique is described, based on synthetic aperture radar (SAR) interferometry, which uses SAR images for measuring very small (1 cm or less) surface motions with good resolution (10 m) over swaths of up to 50 km. The method was applied to a Seasat data set of an imaging site in Imperial Valley, California, where motion effects were observed that were identified with movements due to the expansion of water-absorbing clays. The technique can be used for accurate measurements of many geophysical phenomena, including swelling and buckling in fault zones, residual displacements from seismic events, and prevolcanic swelling.

Gabriel, Andrew K.↗
NASA NTRS1989

Performance of Large Area Xenon Ion Thrusters for Orbit Transfer Missions

Studies have indicated that xenon ion propulsion systems can enable the use of smaller earth-launch vehicles for satellite placement which results in significant cost savings. These analyses have assumed the availability of advanced, high power ion thrusters-operating at about 10 kW or higher. A program was initiated to explore the viability of operating 50 cm diameter ion thrusters at this power level. Operation with several discharge chamber and ion extraction grid set combinations was demonstrated and data were obtained at power levels to 16 kW. Fifty cm diameter thrusters using state of the art 30 cm diameter grids or advanced technology 50 cm diameter grids allow discharge power and beam current densities commensurate with long life at power levels up to 10 kW. In addition, 50 cm diameter thrusters are shown to have potential for growth in thrust and power levels beyond 10 kW.

Rawlin, Vincent K.↗
NASA NTRS1989

Performance of the large-area detectors for the Burst and Transient Source Experiment (BATSE) on the Gamma Ray Observatory

BATSE, one of four experiments on the Gamma Ray Observatory (GRO), is expected to provide the most sensitive observations of gamma-ray bursts yet obtained, as well as to provide long-term monitoring of hard X-ray and low-energy gamma-ray emission from bright pulsating sources, transients, and solar flares. Eight uncollimated modules, positioned at the corners of the spacecraft to provide an unobstructed view of the sky, detect sources by various techniques based on time variability. Use of detectors with anisotropic response allows location of gamma-ray bursts to be determined to an accuracy of about 1 deg using BATSE data alone. The completed BATSE underwent intensive testing and calibration prior to its delivery in October 1988.

Paciesas, W. S.↗
NASA NTRS1991

Properties of large area ErBa2Cu3O(7-x) thin films deposited by ionized cluster beams

ErBa2Cu3O(7-x) films have been produced by simultaneous deposition of Er, Ba, and Cu from three ionized cluster beam (ICB) sources at acceleration voltages of 0.3 to 0.5 kV. Combining ozone oxidation with ICB deposition at 650 C eliminated any need of post annealing processing. The substrates were rotated at 10 rotations per minute during the deposition which took place at a rate of about 3 to 4 nm. Films with areas up to 70 mm in diameter have been made by ICB deposition. These films, 100 nm thick, were deposited on SrTiO3 (100) substrates at 650 C in a mixture of six percent O3 in O2 at a total pressure of 4 x 10(exp -4) Torr. They had T(sub c) ranging from 84.3 K to 86.8 K over a 70 mm diameter and J(sub c) above 10(exp 6) A/sq cm at 77 K. X ray diffraction measurements of the three samples showed preferential c-axis orientation normal to the substrate surface. Scanning electron micrographs (SEM) of the three samples also show some texture dependence on sample position. For the three samples, there is a correlation between SEM texture, full width at half-maximum of rocking curves and J(sub c) versus temperature curves.

Levenson, L. L.↗
NASA NTRS1991

Properties of large area ErBa2Cu3O(7-x) thin films deposited by ionized cluster beams

Ionized cluster beam (ICB) deposition is employed to produce ErBa2Cu3O(7-x) films on different substrates without post-annealing. Films with diameters of up to 70 mm are grown on SrTiO3 100 plane and exhibit Tc values of 84-87 K, Jc of about 10 exp 6 A/sq m at 77 K. These films are epitaxial with the c-axis perpendicular to the plane of the substrate surface, and they can be routinely produced by ICB with good Jc and Tc.

Levenson, L. L.↗
NASA NTRS1992

Large area solar cells from lunar materials

The first goal of the project was to produce polymers from materials available on the Moon. This, apparently simple, aim is made complicated by the fact that there is no carbon on the Moon and there are no polymers (with a couple of irrelevant exceptions) known which do not contain carbon. Because of the abundance of silicon and oxygen in the lunar regolith, it was decided to aim to produce siloxane polymers with the (-Si-O-) backbone found in silicones. A univalent side group is also needed but there are no univalent elements available in the regolith which could plausibly make stable structures. Failing this, hydrogen is a good choice for side group since it accounts for a small fraction of the total weight of the polymer. Thus, a group of target structures such as (-SiH2-O-)n, (-Si(OH)2-O-)n is determined. This goal was approached via a series of simpler syntheses. During the first year, polydimethylsiloxane (-Si(CH3)2-O-)n was made by controlled hydrolysis of SiCl2(CH3)2, which is a routine synthesis, and then an attempt was made to make polydichlorosiloxane by controlled hydrolysis of SiCl4. At the end of the first year, some infra-red spectra indicated that this product had been obtained.

Bryant, Read↗
NASA NTRS1992

Large-area YBa2Cu3O(7-delta) thin films on sapphire for microwave applications

We have deposited YBa2Cu3O(7-delta) (YBCO) films with low microwave surface resistance (Rs) on 5-cm-diam, oxide-buffered sapphire substrates by planar magnetron sputtering. MgO buffer layers are used on M-plane (1 0 -1 0) sapphire, and R-plane (1 -1 0 2) sapphire is buffered by CeO2. Rs values of 450-620 microhms at 77 K and 10 GHz were measured across an entire 5-cm diam YBCO film on M-plane sapphire. For YBCO on R-plane sapphire, Rs values at 77 K and 10 GHz were 950 microohms for a 5-cm-diam wafer and 700 microohms for 1 x 1 sq cm samples.

Cole, B. F.↗
NASA NTRS1993

Monitoring of wildfires in boreal forests using large area AVHRR NDVI composite image data

Normalized difference vegetation index (NDVI) composite image data, produced from AVHRR data collected in 1990, were evaluated for locating and mapping the areal extent of wildfires in the boreal forests of Alaska during that year. A technique was developed to map forest fire boundaries by subtracting a late-summer AVHRR NDVI image from an early summer scene. The locations and boundaries of wildfires within the interior region of Alaska were obtained from the Alaska Fire Service, and compared to the AVHRR-derived fire-boundary map. It was found that AVHRR detected 89.5 percent of all fires with sizes greater than 2000 ha with no false alarms and that, for most cases, the general shape of the fire boundary detected by AVHRR matched those mapped by field observers. However, the total area contained within the fire boundaries mapped by AVHRR were only 61 percent of those mapped by the field observers. However, the AVHRR data used in this study did not span the entire time period during which fires occurred, and it is believed the areal estimates could be improved significantly if an expanded AVHRR data set were used.

Kasischke, Eric S.↗
NASA NTRS1994

Continuum spectral characteristics of bursts measured with BATSE large area detectors

The continuum spectra of bursts are studied with particular emphasis placed on the search for spectral subcomponents. The spectra observed in individual bursts show significant evolution throughout their durations. The degree to which hard and soft spectra are combined in bursts and the effect this has on the complexity of the observed spectra are addressed. In particular the presence of broad cusps in spectra in the 50-100 keV range are studied to determine both the degree to which these features are present in the LAD data and whether superposition of hard and soft spectra simultaneously can account for them. Also the time histories of the power output (ergs/sec) from bursts are studied to investigate the dynamic coupling between hard and soft spectra in bursts as a probe of the autonomy of the hard and soft emission mechanisms.

Pendleton, Geoffrey N.↗
NASA NTRS1994

Large area soft x-ray collimator to facilitate x-ray optics testing

The first objective of this program is to design a nested conical foil x-ray optic which will collimate x-rays diverging from a point source. The collimator could then be employed in a small, inexpensive x-ray test stand which would be used to test various x-ray optics and detector systems. The second objective is to demonstrate the fabrication of the x-ray reflectors for this optic using lacquer-smoothing and zero-stress electroforming techniques.

Espy, Samuel L.↗
NASA NTRS1995

On treatments of fetch and stability sensitivity in large-area estimates of sensible heat flux over sea ice

Bulk transfer coefficients estimated as a function of atmospheric stability and sea-ice lead width are combined with Arctic meteorological observations and ice thickness data to calculate the sensitivity of turbulent flux estimates to changes in lead width, wind speed, air temperature, and ice thickness for a high-concentration ice pack. These results are considered in terms of bulk transfer parameterizations that use a fixed transfer coefficient r that address atmospheric stability only. On the basis of the fetch-sensitive parameterizations considered here, differences in lead width for widths up to about 200 m can exert a substantial influence on sensible heat transfer coefficients and heat flux from leads under typical Arctic conditions. Fluxes from an open water lead decrease by 34% if fetch increases from 10 m to 100 m. This effect is greatest for open water leads, decreases considerably as leads refreeze, and is negligible for ice thicker than about 0.3 m. If open or newly refrozen leads make up 2% of the ice cover, than an increase in mean fetch from 10 m to 100 m yields a decrease of about 2 W/sq m in areally averaged flux from the ice pack. Calculations using observed and theoretical lead width distributions suggest that parameterizing lead widths in a sea ice model can be done effectively using a single, representative lead width rather than requiring a full distribution of widths. When coupled to the lowest atmospheric boundary layer using a bulk similarity theory model, this sensitivity of heat transfer to fetch results in substantially higher near-surface air temperatures over narrow leads, with equilibrium air temperatures decreasing by about 50% as fetch increases from 10 to 100 m.

Maslanik, J. A.↗
NASA NTRS1995

Fabrication of large-area CCD detectors on high-purity, float-zone silicon

In this report on the fabrication of a 1024 x 1024 charge coupled device (CCD) imager to be used as a soft x-ray sensor onboard the Advanced X-ray Astronomical Facility (AXAF), the following conclusions were found: the dislocations that limited the performance of the high resistivity imager were characterized; the sources of stress were identified and the dislocations found were eliminated; and a charge transfer inefficiency (CTI) of 10(exp -6) and read noise as low as 1.3/e was demonstrated. This sensor must have low noise and a low CTI and must be radiation hardened to withstand any radiation damage from a space environment.

Gregory, J. A.↗
NASA NTRS1996

Thin, Large-Area Positive Electrodes in Na/NiCl(2) Cells

Thin, larger-area, noncylindrical positive electrodes investigated for use in place of smaller-area, cylindrical positive electrodes now used in Na/NiCl(2) high-temperature rechargeable electrochemical cells and batteries. Greater power densities achievable, without compromising on energy densities.

Bugga, Ratnakumar↗
NASA NTRS1996

Studies of Large-Area Inversion-Layer Metal-Insulator-Semiconductor (IL/MIS) Solar Cells and Arrays

Many inversion-layer metal-insulator-semiconductor (IL/MIS) solar cells have been fabricated. There are around eighteen 1 cm(exp 2) IL/MIS solar cells which have efficiencies greater than 7%. There are only about three 19 cm(exp 2) IL/MIS cells which have efficiencies greater than 4%. The more accurate control of the thickness of the thin layer of oxide between aluminum and silicon of the MIS contacts has been achieved. A lot of effort and progress have been made in this area. A comprehensive model for MIS contacts under dark conditions has been developed that covers a wide range of parameters. It has been applied to MIS solar cells. One of the main advantages of these models is the prediction of the range of the thin oxide thickness versus the maximum efficiencies of the MIS solar cells. This is particularly important when the thickness is increased to 25 A. This study is very useful for our investigation of the IL/MIS solar cells. The two-dimensional numerical model for the IL/MIS solar cells has been tried to develop and the results are presented in this report.

Ho, Fat Duen↗
NASA NTRS1994

The Effects of Sensor Field-of-View on the Geometrical Characteristics of Sea Ice Leads and Implications for Large-Area Heat Flux Estimates

The release of heat from sea ice fractures ('leads') is an important component of the heat budget in the Arctic, but their impact on regional scale climate is difficult to assess without more information on their distribution in both space and time. Remote sensing of leads using satellite data, specifically AVHRR thermal and Landsat visible-band imagery, is examined empirically with respect to lead width, orientation, and area fraction. The geometrical aspects of the sensor are simulated so that the effect of sensor field-of-view on retrieved lead width statistics can be assessed. This is done using Landsat data and simulated lead networks degraded to AVHRR pixel sizes. The analyses illustrate how leads of sufficiently high contrast tend to 'grow' with increasing pixel size and how small or low contrast leads disappear. The relationship between lead contrast and the width/field-of-view ratio is also examined in order to determine the limits of lead detectability, and illustrates the multivalued nature of the problem of lead width retrieval. To help quantify the importance of changes in lead statistics, turbulent heat flux is calculated as a function of lead width and lead fraction. It is shown that pixel size has a substantial effect on estimates of turbulent heat transfer from leads to the atmosphere.

Key, J.↗
NASA NTRS1999

Research with Large Area Imaging X-Ray Telescope Sounding Rocket Program

We are engaged in a program to develop focussing hard X-ray telescopes in a double conical or Wolter 1 geometry that function up to 100 keV by employing small graze angles and multilayer coatings. Directly polished substrates are not an option because they are too thick to be nested efficiently. The only alternative is to fabricate the very thin substrates by replication. Our objective is the production of integral cylindrical substrates because they should result in better angular resolution than segmented foil geometries. In addition, integral cylinders would be more resistant to possible stress from deep multilayer coatings than segmented ones. Both electroforming of nickel (method of SkX, JET-X, and XMM) and epoxy replication are under consideration. Both processes can utilize the same types of mandrels and separation agents- While electroforming can produce substrates that are thin, the high density of the nickel may result in high weight optics for some missions. For convenience, experimentation with replication and coating is being carried out initially on flats. Our replication studies include trials with gold and carbon separation agents. This paper reports on our efforts with epoxy replicated optics.

Gorenstein, Paul↗
NASA NTRS1999

New Mission Concepts for Astrophysics Large Area X-Ray Spectroscopy Mission

Work at SAO was performed under the overall direction of Dr. Harvey Tananbaum, the Principal Investigator for the program. Dr. Jay Bookbinder was responsible for day to day program coordination at SAO and liaison with GSFC. Dr. Nicholas E. White served as GSFC Technical Officer for the Grant. The effort was directed at formulating the general characteristics and scientific requirements of the contemplated mission. While funding and therefore effort was limited, nonetheless SAO was involved in a broad range of activities. These activities were defined by our SAO proposal to GSFC that were subsequently accepted and funded by this Grant. The main activities were: Support of mission studies. Support the development of science requirements. and Performance of selected engineering studies and trades. During this period, an integrated GSFC/SAO management team began to form and work together. Jean F. Grady was appointed Project Formulation Manager at GSFC and assumed the overall management direction of the project including coordination of work performed under the grant.

Tananbaum, Harvey↗