Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “injection rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Electron-cyclotron maser and solar microwave millisecond spike emission

An intense solar microwave millisecond spike emission (SMMSE) event was observed on May 16, 1981 by Zhao and Jin at Beijing Observatory. The peak flux density of the spikes is high to 5 x 100,000 s.f.u. and the corresponding brightness temperature (BT) reaches approx. 10 to the 15th K. In order to explain the observed properties of SMMSE, it is proposed that a beam of electrons with energy of tens KeV injected from the acceleration region downwards into an emerging magnetic arch forms so-called hollow beam distribution and causes electron-cyclotron maser (ECM) instability. The growth rate of second harmonic X-mode is calculated and its change with time is deduced. It is shown that the saturation time of ECM is t sub s approx. equals 0.42 ms and only at last short stage (delta t less than 0.2 t sub s) the growth rate decreases to zero rather rapidly. So a SMMSE with very high BT will be produced if the ratio of number density of nonthermal electrons to that of background electrons, n sub s/n sub e, is larger than 4 x .00001.

Li, Hong-Wei↗
NASA NTRS1989

Two-dimensional analysis of two-phase reacting flow in a firing direct-injection diesel engine

The flow field, spray penetration, and combustion in two-stroke diesel engines are described. Fuel injection begins at 345 degrees after top dead center (ATDC) and n-dodecane is used as the liquid fuel. Arrhenius kinetics is used to calculate the reaction rate term in the quasi-global combustion model. When the temperature, fuel, and oxygen mass fraction are within suitable flammability limits, combustion begins spontaneously. No spark is necessary to ignite a localized high temperature region. Compression is sufficient to increase the gaseous phase temperature to a point where spontaneous chemical reactions occur. Results are described for a swirl angle of 22.5 degrees.

Nguyen, H. Lee↗
NASA NTRS1995

Effects of Initial Conditions on a Single Jet in Crossflow

An experimental investigation of the effects of jet inlet flow conditions has been conducted for the isothermal mixing of a single jet injected into a crossflow. Jet penetration and mixing was studied using planar Mie scattering to measure time-averaged jet mixture fraction distributions. The effects of 'passive' control methods such as jet 'tabs' and jet swirl are reported. Mixing effectiveness, determined using a spatial unmixedness parameter based on the variance of the mean jet concentration distributions, was compared to a baseline case of a round jet injected into a uniform crossflow. All results are compared at a jet-to-mainstream momentum-flux ratio of 8.5. In the near-field, the mixing rates are similar to, or less than, the baseline configuration using this measure of mixedness. None of the tested configurations appear to significantly augment mixing within a downstream distance of 3 diameters of an equivalent-area round orifice.

Liscinsky, D. S.↗
NASA NTRS1999

The Effects of LOX Post Biasing on SSME Injector Wall Compatibility

An experimental investigation has been carried out to examine the effects of LOX post biasing of a shear coaxial injector on the behavior of the spray near a chamber wall. The experimental work was performed with inert propellant simulants in a high-pressure chamber. Injector flow rates and chamber pressure were designed to match the Space Shuttle Main Engine (SSME) injector gas-to-liquid density and velocity ratio at the point of propellant injection. Measurements of liquid mass flux, gas phase velocity and droplet size were made using mechanical patternation and phase Doppler interferometry techniques. The measurements revealed that the liquid mass flux distribution shifts away from the wall with increasing LOX post bias away from the wall. The shift in the liquid flux distribution was much greater than that caused by the angling of the LOX post alone. Gas velocity near the wall simultaneously increased with increasing LOX post bias away from the wall. The increase in wall side gas velocity was due to the higher fraction of gas injected on the wall side of the injector as a result of the eccentricity at the injector exit. The net result is a decrease in mixture ratio near the wall. Estimates of heat transfer and engine performance relative to the unbiased case are presented.

Strakey, P. A.↗
NASA NTRS2000

Computational Analysis of the Combustion Processes in an Axisymmetric, RBCC Flowpath

Computational fluid dynamic simulations have been used to study the combustion processes within an axisymmetric, RBCC flowpath. Two distinct operating modes have been analyzed to date, including the independent ramjet stream (IRS) cycle and the supersonic combustion ramjet (scramjet) cycle. The IRS cycle investigation examined the influence of fuel-air ratio, fuel distribution, and rocket chamber pressure upon the combustion physics and thermal choke characteristics. Results indicate that adjustment of the amount and radial distribution of fuel can control the thermal choke point The secondary mass flow rate was very sensitive to the fuel-air ratio and the rocket chamber pressure. The scramjet investigation examined the influence of fuel-air ratio and fuel injection schedule upon combustion performance estimates An analysis of the mesh-dependence of these calculations was presented. Jet penetration data was extracted from the three-dimensional simulations and compared favorably with experimental correlations of similar flows. Results indicate that combustion efficiency was very sensitive to the fuel schedule.

Steffen, Christopher J., Jr.↗
NASA NTRS2001

Computational Analysis of the Combustion Processes in an Axisymmetric, RBCC Flowpath

Computational fluid dynamic simulations have been used to study the combustion processes within an axisymmetric, RBCC flowpath. Two distinct operating modes have been analyzed to date, including the independent ramjet stream (IRS) cycle and the supersonic combustion ramjet (scramJet) cycle. The IRS cycle investigation examined the influence of fuel-air ratio, fuel distribution, and rocket chamber pressure upon the combustion physics and thermal choke characteristics. Results indicate that adjustment of the amount and radial distribution of fuel can control the thermal choke point. The secondary massflow rate was very sensitive to the fuel-air ratio and the rocket chamber pressure. The scramjet investigation examined the influence of fuel-air ratio and fuel injection schedule upon combustion performance estimates. An analysis of the mesh-dependence of these calculations was presented. Jet penetration data was extracted from the three-dimensional simulations and compared favorably with experimental correlations of similar flows. Results indicate that combustion efficiency was very sensitive to the fuel schedule.

Steffen, Christopher J., Jr.↗
NASA NTRSDate not supplied

Artemis I Off-Nominal-Trajectory Design and Optimization

In order to achieve the Artemis I mission objectives to human-rate the Orion spacecraft even under off-nominal conditions, trajectories were developed to handle contingency scenarios: alternate missions for contingencies before or during the Trans-Lunar Injection burn, recoveries to return Orion to the nominal trajectory after a delayed or partial burn, and abort trajectories to return the spacecraft to Earth after a critical failure. In addition, disposal trajectories were generated for situations where recovery was not an option. Details are given on the trajectory characteristics, solution families, the generation of the trajectories, and operations considerations.

Artemis I↗
NASA NTRSDate not supplied

Transient Liquefaction on the Lunar or Martian Surface Operational Demonstration

As developments of local production of cryogenic fluids on the Lunar or Martian Surface progress, it is important to understand transient system responses to help with the balancing of process plant power and understanding system level operations. During the Cryogenic Fluid In-situ Liquefaction for Landers (CryoFILL) testing, a series of transient oxygen liquefaction tests were completed. These tests included varying liquefaction flow rate, environmental temperature, tank fill level, and effective cryocooler lift while allowing the tank pressure to respond to the input controls. An additional transient test was run at the 90% fill level to determine the impact of injecting the gaseous oxygen at the bottom of the tank, allowing the vapor to bubble up through the liquid. Tests were run in a cyclical nature varying one variable at a time. The control variable was set in a manner to increase tank pressure for a period of time and then subsequently changed in a manner to decrease the tank pressure back to its original value with multiple cycles run for all tests. Tank pressure and system temperature responses were tracked as a function of time with an emphasis on repeatability. Results indicate that of the four variables tested, the environmental temperature is the least important. As expected, the bubbling of the liquefaction gas significantly decreased the pressurization and depressurization rates in the tank at the 90% full level.

Liquefaction↗
NASA NTRS1972

Flowing gas, non-nuclear experiments on the gas core reactor

Flow tests were conducted on models of the gas core (cavity) reactor. Variations in cavity wall and injection configurations were aimed at establishing flow patterns that give a maximum of the nuclear criticality eigenvalue. Correlation with the nuclear effect was made using multigroup diffusion theory normalized by previous benchmark critical experiments. Air was used to simulate the hydrogen propellant in the flow tests, and smoked air, argon, or freon to simulate the central nuclear fuel gas. All tests were run in the down-firing direction so that gravitational effects simulated the acceleration effect of a rocket. Results show that acceptable flow patterns with high volume fraction for the simulated nuclear fuel gas and high flow rate ratios of propellant to fuel can be obtained. Using a point injector for the fuel, good flow patterns are obtained by directing the outer gas at high velocity along the cavity wall, using louvered or oblique-angle-honeycomb injection schemes.

Kunze, J. F.↗
NASA NTRS1997

Ejector Noise Suppression with Auxiliary Jet Injection

An experimental program to reduce aircraft jet turbulence noise investigated the interaction of small auxiliary jets with a larger main jet. Significant reductions in the far field jet noise were obtained over a range of auxiliary jet pressures and flow rates when used in conjunction with an acoustically lined ejector. While the concept is similar to that of conventional ejector suppressors that use mechanical mixing devices, the present approach should improve thrust and lead to lower weight and less complex noise suppression systems since no hardware needs to be located in the main jet flow. A variety of auxiliary jet and ejector configurations and operating conditions were studied. The best conditions tested produced peak to peak noise reductions ranging from 11 to 16 dB, depending on measurement angle, for auxiliary jet mass flows that were 6.6% of the main jet flow with ejectors that were 8 times the main jet diameter in length. Much larger reductions in noise were found at the original peak frequencies of the unsuppressed jet over a range of far field measurement angles.

Berman, Charles H.↗
NASA NTRS1994

Middle- and low-latitude emissions from energetic neutral atom precipitation seen from ATLAS 1 under quiet magnetic conditions

During the ATLAS 1 mission spectral observations were made at middle and low latitudes of features expected from the precipitation of energetic neutral atoms. The Imaging Spectrometric Observatory was used at night in the UV and visible with maximum gain. The tangent ray heights of the look directions ranged from near 100 km to near 200 km, and the geomagnetic conditions were quiet during the observations, which were made March 28 to April 3, 1992. The N2(+) 1N 391.4-nm and O I 130.4 and 135.6-nm emissions were observed at all latitudes, with lower emission rates at lower magnetic dip latitudes, except that enhancements in the O I lines were seen within 30 deg of the dip equator to radiative recombination of ionospheric plasma. The latitude profile observed for the N2(+) 1N emission did not show an equatorial or midlatitude peak. This implies that the source of energetic neutrals is more consistent with prompt charge exchange loss of freshly injected trapped ions with relatively low mirror heights (i.e., ions on higher L shells with equatorial pitch angle distributions nearly isotropic to the loss cone) than loss of highly eroded populations of particles with high mirror heights (i.e., ions on lower L shells with pancake equatorial pitch angle distributions). The N2(+) 1N emission rates have been compared with models of atmospheric emission due to fluxes of O/O(+) and H/H(+) in the thermosphere, as produced by energetic neutral oxygen or hydrogen atom precipitation. Energy deposition rates are inferred.

Tinsley, B. A.↗
NASA NTRS1973

Technique for predicting high-frequency stability characteristics of gaseous-propellant combustors

A technique for predicting the stability characteristics of a gaseous-propellant rocket combustion system is developed based on a model that assumes coupling between the flow through the injector and the oscillating chamber pressure. The theoretical model uses a lumped parameter approach for the flow elements in the injection system plus wave dynamics in the combustion chamber. The injector flow oscillations are coupled to the chamber pressure oscillations with a delay time. Frequency and decay (or growth) rates are calculated for various combustor design and operating parameters to demonstrate the influence of various parameters on stability. Changes in oxidizer design parameters had a much larger influence on stability than a similar change in fuel parameters. A complete description of the computer program used to make these calculations is given in an appendix.

Priem, R. J.↗
NASA NTRS1979

Coolant tube curvature effects on film cooling as detected by infrared imagery

Reported herein are comparative thermal film cooling footprints observed by infrared imagery from straight, curved and looped coolant tube geometries. It was hypothesized that the difference in secondary flow and turbulence structure of flow through these three tubes should influence the mixing properties between the coolant and mainstream. The coolant was injected across an adiabatic plate through a hole angled at 30 deg to the surface in line with the free stream flow. The data cover a range of blowing rates from 0.37 to 1.25 (mass flow per unit area of coolant divided by free stream). Average temperature difference between coolant and tunnel air was 25 C. Data comparisons confirmed that coolant tube curvature significantly influences film cooling effectiveness.

Papell, S. S.↗
NASA NTRS1991

Effects of unsteady shock impingement on high-speed gaseous mixing

Tests are performed to determine the effects of impinging oscillating shocks of different frequencies on a 15 deg downstream angled, underexpanded, sonic helium jet injected into a supersonic airflow. Information on mixing, penetration, total pressure loss, and turbulence structure from these tests is employed to estimate mixing control achieved by adding an oscillating shock to the helium injection flow field. The principal result of this study is that impingement of an oscillating shock on a high-speed shear layer can be utilized to control the rate of mixing.

Wood, C. W.↗
NASA NTRS1997

Angled Injection: Turbulent Flow Hybrid Bearings Comparison to Test Results

Hydrostatic/hydrodynamic (hybrid) journal bearings handling process liquids have limited dynamic stability characteristics and their application as support elements to high speed flexible rotating systems is severely restricted. Measurements on water hybrid bearings with angled orifice injection have demonstrated improved rotordynamic performance with virtual elimination of cross-coupled stiffness coefficients and null or negative whirl frequency ratios. A bulk-flow model for prediction of the static performance and force coefficients of hybrid bearings with angled orifice injection is advanced. The analysis reveals that the fluid momentum exchange at the orifice discharge produces a pressure rise in the hydrostatic recess retards the shear flow induced by journal rotation, and thus, reduces cross-coupling forces. The predictions from the model are compared with experimental measurements for a 45 deg. angled orifice injection, 5 recess water hybrid bearing operating at 10.2, 17.4, and 24.6 krpm and with supply pressures of 4, 5.5, and 7 MPa. The correlations include recess pressures, flow rates, and rotordynamic force coefficients at the journal centered position.

SanAndres, Luis↗
NASA NTRS2000

Bioavailability and Pharmacodynamics of Promethazine in Human Subjects

Space Motion Sickness (SMS) is often treated in space with promethazine (PMZ). Anecdotal reports indicate that the common side effects of drowsiness and decrements in cognitive performance that are associated with PMZ administration (50 mg IM on the ground, are absent or less pronounced in space suggesting I that-the bioavailability and/or pharmacodynamic behavior of PMZ may be altered during space flight. There are limited flight opportunities available for clinical research in space, the NRA-99, therefore, solicits research required to improve, or answer specific questions about in-flight diagnosis, therapy, and post-flight rehabilitation. We propose here, to establish a noninvasive method for pharmacodynamic and therapeutic assessment of PMZ. The specific objectives of the proposed research are to, 1. Establish a saliva to plasma ratio of PMZ after administration, 2. Estimate the relative bioavailability of the three flight-specific dosage forms of PMZ, and 3. Establish the dose-response relationship of PMZ. We will estimate the bioavailability of intramuscular injection (IM), oral tablets and rectal suppositories in normal subjects during ambulatory and antiorthostatic; bed rest (ABR) conditions using novel stable isotope techniques. Drowsiness, cognitive performance and salivary flow rate will be measured as a function of circulating drug concentrations after administration of three IM doses of PMZ. We will compare and contrast the bioavailability of PMZ during normal and ABR conditions to examine whether or not ABR can simulate changes in drug, absorption and availability similar to those anticipated in a microgravity environment. Results of this study will validate methods for an approved study with this medication awaiting a flight opportunity for manifestation. These data will also provide the much needed information on the dynamics and therapeutic index. of this medication and their implications on crew fatigue and performance in space. Key words: Promethazine, stable isotopes, bioavailability, pharmacodynamics, cognitive performance, antiorthostatic bed rest.

Putcha, Lakshmi↗
NASA NTRS1995

Sensitivity of two-dimensional model predictions of ozone response to stratospheric aircraft: An update

The Goddard Space Flight Center (GSFC) two-dimensional model of stratospheric photochemistry and dynamics has been used to calculate the O3 response to stratospheric aircraft (high-speed civil transport (HSCT)) emissions. The sensitivity of the model O3 response was examined for systematic variations of five parameters and two reaction rates over a wide range, expanding on calculations by various modeling groups for the NASA High Speed Research Program and the World Meteorological Organization. In all, 448 model runs were required to test the effects of variations in the latitude, altitude, and magnetitude of the aircraft emissions perturbation, the background chlorine levels, the background sulfate aerosol surface area densities, and the rates of two key reactions. No deviation from previous conclusions concerning the response of O3 to HSCTs was found in this more exhaustive exploration of parameter space. Maximum O3 depletions occur for high-altitude, low altitude HSCT perturbations. Small increases in global total O3 can occur for low-altitude, high-altitude injections. Decreasing aerosol surface area densities and background chlorine levels increases the sensitivity of model O3 to the HSCT perturbations. The location of the aircraft emissions is the most important determinant of the model response. Response to the location of the HSCT emissions is not changed qualitatively by changes in background chlorine and aerosol loading. The response is also not very sensitive to changes in the rates of the reactions NO + HO2 yields NO2 + OH and HO2 + O3 yields OH + 2O2 over the limits of their respective uncertainties. Finally, levels of lower stratospheric HO(sub x) generally decrease when the HSCT perturbation is included, even though there are large increases in H2O due to the perturbation.

Considine, David B.↗
NASA NTRS1976

Teledyne Continental Motors emissions data and analysis and flight test results

Five different engine models were tested covering combinations of all engine categories in current production in the range from 100 to 435 brake horsepower. Engines were divided into five major types: carbureted, fuel injected, direct drive, geared, and turbocharged. Emissions data were categorized by three separate fuel system schedules: baseline, case 1, and case 2. Baseline was defined as the average fuel flow rate established by the fuel system's production tolerance band when operated with the mixture control at the full-rich position. Case 1 was defined as the minimum allowable fuel flow rate established by the engine certification. Case 2 was defined as the fuel rate corresponding to the leanest fuel-air ratio obtainable before a safety limit occurred with the engine operating on a propeller test stand. Safety limits that developed during testing were cylinder-head overheating or inadequate acceleration from a given mode of operation.

Rezy, B. J.↗