Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphitization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Electrochemical behavior of 0.2 to 3 molar ferrous chloride-ferric chloride mixtures on edge-on pyrolytic graphite rotated disk electrodes

Potentiostatic determinations in various mixtures of FeCl2-FeCl3 with excess HCl show rest potentials that are 0.1 V less electropositive than the theoretical values from the formulated ratios of FeII to FeIII (probably as a result of complexing). The standard rate constant sub s. ranges between 0.0001 and 0.000 cm/sec. Tafel slopes b of roughly 0.12V per decade indicate single-electron exchange kinetics. No significant trend in either b or sub s was attributed to mixture composition. The higher sub s. values occurred with and edge-on pyrolytic graphite that had undergone a permanent surface change.

Miller, R. O.↗
NASA NTRS1977

Design and fabrication of graphite-epoxy bolted wing skin splice specimens

Graphite-epoxy bolted joint specimens were designed and fabricated. These specimens were to be representative of a side-of-body wing skin splice with a 20-year life expectancy in a commercial transport environment. Preliminary tests were performed to determine design values of bearing and net tension stresses. Based upon the information developed, a three-fastener-wide representative wing skin splice was designed for a load of 2627 KN/m (15,000 lbf/in.). One joint specimen was fabricated and tested at NASA. The wing skin splice failed at 106 percent of design ultimate load. This joint design achieved all static load objectives. Fabrication of six specimens, together with their loading fixtures, was completed, and the specimens were delivered to NASA-LRC.

Johnson, R. W.↗
NASA NTRS1977

Effect of bow-type initial imperfection on the buckling load and mass of graphite-epoxy blade-stiffened panels

A structural synthesis computer code which accounts for first order effects of an initial bow and which can be used for sizing stiffened composite panels having an arbitrary cross section is used to study graphite blade-stiffened panels. The effect of a small initial bow on both the load carrying ability of panels and on the mass of panels designed to carry a specified load is examined. Large reductions in the buckling load caused by a small initial bow emphasize the need for considering a bow when a panel is designed.

Stroud, W. J.↗
NASA NTRS1976

The graphite crystal X-ray spectrometer on OSO-8

The large-area graphite crystal X-ray spectrometer aboard the OSO-8 satellite is described. The instrument can be used to measure continuum profiles over the energy band from 2 to 8 keV with a resolution of several tens of electron volts and to detect narrow line emission from strong X-ray sources with a limiting sensitivity (3 sigmas) of the order of 10-eV, equivalent width for a three-day observing period.

Kestenbaum, H. L.↗
NASA NTRS1977

Impact behavior of graphite-epoxy simulated fan blades

The response of a graphite-epoxy material, Modmor II/PR-286, to foreign object impact was investigated by impacting spherical projectiles of three different materials - gelatin, ice, and steel - on simulated blade specimens. Visual and metallographic inspection revealed three damage mechanisms: penetration, leading edge bending failure, and stress wave delamination and cracking. The steel projectiles caused penetration damage regardless of the impact location and angle. For the ice and gelatin particles impacting the leading edge, failure was due to large local bending strains, resulting in significant material removal and delamination damage.

Cook, T. S.↗
NASA NTRS1977

Graphite grain surface reactions in interstellar and protostellar environments

Surface reactions on warm (at least 60 K) graphite grains between lattice C atoms and impinging H and O atoms within or in the vicinity of H II regions can provide a prolific source of H2CO and other interstellar molecules. It is proposed that similar reactions in the primitive solar nebula led to the formation of the organic molecules found in carbonaceous chondrites. From this and related evidence, it is argued that most of the solid material in the solar system may have originated as interstellar grains.

Barlow, M. J.↗
NASA NTRS1977

Use of the short-beam shear test for quality control of graphite-polyimide laminates

The properties of laminated composite materials are strongly affected by many fabrication variables including temperature, time, and molding pressure. It is therefore necessary to have reliable quality control tests to check the properties of manufactured materials. The short-beam shear test is used widely by both manufacturers and researchers as a quality control test in the production of materials and development of new material systems. There are, however, several limitations to the standard test method. This paper presents the results of short-beam shear tests on graphite-polyimide laminates and reports on stiffness-strength relationships and nondestructive evaluation methods which aid in the interpretation of the test data.

Stinchcomb, W. W.↗
NASA NTRS1977

Experimental studies of graphite-epoxy and boron-epoxy angle ply laminates in shear

The nonlinear/inelastic response under inplane shear of a large variety of graphite-epoxy and boron-epoxy angle-ply laminates was tested. Their strength allowables were obtained and the mechanisms which govern their mode of failure were determined. Two types of specimens for the program were chosen, tested, and evaluated: shear panels stabilized by an aluminum honeycomb core and shear tubes. A modified biaxially compression/tension loaded picture frame was designed and utilized in the test program with the shear panels. The results obtained with this test technique categorically prefer the shear panels, rather than the tubes, for adequate and satisfactory experimental definition of the objectives. Test results indicate the existence of a so-called core-effect which ought to be considered when reducing experimental data for weak in shear laminates.

Weller, T.↗
NASA NTRS1977

Analytical and experimental studies of graphite-epoxy and boron-epoxy angle ply laminates in shear

The results of a comparison study between a test program on the inelastic response under inplane shear over a wide range of graphite-epoxy and boron-epoxy angle-ply laminates are reported. This investigation was aimed at evaluating the applicability and adequacy of these analyses to predict satisfactorily the responses of angle-ply laminates. It was observed that these analytical tools are inadequate for this purpose as they fail to predict with sufficient confidence the shape of response and in particular the strength values associated with a given laminate configuration. Consequently, they do not provide the sought-after information about failure mechanisms which trigger failure of a particular designed laminate.

Weller, T.↗
NASA NTRS1977

Experimental studies of graphite-epoxy and boron-epoxy angle ply laminates in compression

A test program aimed at studying the nonlinear/inelastic response under axial compression across a wide range of angle ply was graphite-epoxy and boron-epoxy laminates was presented and described. The strength allowables corresponding to the various laminate configurations were defined and the failure mechanisms which dictate their mode of failure were detected. The program involved two types of specimens for each laminate configuration: compression sandwich coupons and compression tubes. The test results indicate that the coupons perform better than the tubes displaying considerably high stress-strain allowables and mechanical properties relative to the tubes. Also, it is observed that depending on their dimensions the coupons are susceptible to very pronounced edge effects. This sensitivity results in assigning to the laminate conservative mechanical properties rather than the actual ones.

Weller, T.↗
NASA NTRS1977

Analytical and experimental studies of graphite-epoxy and boron-epoxy angle ply laminates in compression

The applicability and adequacy of several computer techniques in predicting satisfactorily the nonlinear/inelastic response of angle ply laminates were evaluated. The analytical predictions were correlated with the results of a test program on the inelastic response under axial compression of a large variety of graphite-epoxy and boron-epoxy angle ply laminates. These comparison studies indicate that neither of the abovementioned analyses can satisfactorily predict either the mode of response or the ultimate stress value corresponding to a particular angle ply laminate configuration. Consequently, also the simple failure mechanisms assumed in the analytical models were not verified.

Weller, T.↗
NASA NTRS1977

Method of adhering bone to a rigid substrate using a graphite fiber reinforced bone cement

A method is described for adhering bone to the surface of a rigid substrate such as a metal or resin prosthesis using an improved surgical bone cement. The bone cement has mechanical properties more nearly matched to those of animal bone and thermal curing characteristics which result in less traumatization of body tissues and comprises a dispersion of short high modulus graphite fibers within a bonder composition including polymer dissolved in reactive monomer such as polymethylmethacrylate dissolved in methylmethacrylate monomer.

Knoell, A. C.↗
NASA NTRS1978

Toughening of graphite-epoxy composites by interlaminar perforated Mylar films

Fracture and notch strength tests of graphite-epoxy composites showed that unidirectional lay-ups generally exhibit longitudinal cracking before failure, whereas multidirectional lay-ups fail transversely with little longitudinal cracking. A simple qualitative analysis suggested that the higher matrix shear stresses in unidirectional materials cause the longitudinal cracking, and that this cracking was responsible for the high toughness of unidirectional composites. In a series of comparative tests, the interlaminar strength of multi-directional composites was reduced by placing perforated Mylar films between laminae; tests on notched and slotted specimens showed that the interlaminar films promoted delamination and longitudinal cracking near the notches and that, as a result, toughness, notch strength, and impact strength were substantially increased.

Elber, W.↗
NASA NTRS1978

Process for utilizing low-cost graphite substrates for polycrystalline solar cells

Low cost polycrystalline silicon solar cells supported on substrates were prepared by depositing successive layers of polycrystalline silicon containing appropriate dopants over supporting substrates of a member selected from the group consisting of metallurgical grade polycrystalline silicon, graphite and steel coated with a diffusion barrier of silica, borosilicate, phosphosilicate, or mixtures thereof such that p-n junction devices were formed which effectively convert solar energy to electrical energy. To improve the conversion efficiency of the polycrystalline silicon solar cells, the crystallite size in the silicon was substantially increased by melting and solidifying a base layer of polycrystalline silicon before depositing the layers which form the p-n junction.

Chu, T. L.↗
NASA NTRS1978

Some effects of composition on friction and wear of graphite-fiber-reinforced polyimide liners in plain spherical bearings

Oscillating, plain spherical bearings with graphite-fiber-reinforced polyimide (GFRPI) liners were tested for friction and wear from 25 to 315 C. A condensation polymer was compared with an addition polymer, and a high-modulus fiber was compared with a lower cost, low-modulus fiber. All polymer-fiber combinations gave friction coefficients from 0.05 to 0.18 and low wear. Adding CdO and CdI2 reduced the wear of degassed bearings in dry air. These additives were not needed when the bearing liners contained adsorbed moisture. Although, at 25 C, MoS2 reduced the friction and wear of the base composite at unit loads above 70,000,000 N/m squared (10,000 psi), it had no beneficial effect at lighter loads.

Sliney, H. E.↗
NASA NTRS1978

Some load limits and self-lubricating properties of plain spherical bearings with molded graphite fiber reinforced polyimide liners to 320 C

Plain spherical bearings with molded liners of self-lubricating graphite fiber-polyimide composite were developed and their dynamic load capacities were determined. Liners were prepared by transfer molding a prepolymer resin-fiber mix into the space between the ball and outer race, the completing polymerization under heat and pressure. Bearing dynamic load capacities were in excess of 140 MPa (20,000 psi) from room temperature to 260 C and about 70 MPa (10,000 psi) at 320 C. Friction coefficients were about 0.20 at room temperatures and light loads and tended to decrease with increasing temperatures and loads to about 0.15. Thermal expansion of the liner at uniform bearing temperatures of 200 C or higher produced a bearing preload which could be alleviated by providing an initial internal diametral clearance of 0.05 to 0.10 mm.

Sliney, H. E.↗
NASA NTRS1977

The correlation of ultrasonic attenuation and shear strength in graphite-polyimide composites

The buffer rod technique for measuring attenuation in thin specimens is modified here to apply to specimens having intermediate thicknesses and high attenuation. The described procedure, which requires only one accessible surface of the material, was used to determine the initial attenuation values of ultrasonic waves in short beam shear specimens of graphite-polyimide composite material. It is shown that there is good correlation between the initial attenuation values and the shear strengths of the specimens determined by the standard short beam shear test method. The modified ultrasonic buffer block technique offers much potential for service as a quantitative, nondestructive, quality assurance test for composite materials.

Hayford, D. T.↗
NASA NTRS1978

NDT of DC-10 graphite-epoxy rudder

The results of visual and ultrasonic nondestructive tests (NDT) on a DC-10 rudder constructed of Thornel 300/5208 graphite-epoxy are presented. A viscous couplant was used for both contact pulse-echo ultrasonics and the Fokker bondtester. Attention is given to the stiffness of cohesive bond structures (the rudder is assembled primarily in a basic six-ply pattern), and to possible delamination. A piezoelectric transducer is employed to sense changes in impedance and signal amplitude. In all, four rudder units were evaluated. The main problems found in the units were porosity and cracking. It is noted that rudder unit four was able to be sufficiently cured to permit static tests on all rib, spar, and skin panel interfaces.

Hagemaier, D. J.↗