Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “glass melting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

Interplanetary meteoroid debris in LDEF metal craters

The extraterrestrial meteoroid residue found lining craters in the Long Duration Exposure Facility (LDEF) aluminum and gold targets is highly variable in both quantity and type. In typical craters only a minor amount of residue is found and for these craters it is evident that most of the impacting projectile was ejected during crater formation. Less than 10 percent of the craters greater than 100 microns contain abundant residue consistent with survival of a major fraction of the projectile. In these cases the residue can be seen optically as a dark liner and it can easily be analyzed by SEM-EDX techniques. Because they are rare, the craters with abundant residue must be a biased sampling of the meteoroids reaching the earth. Factors that favor residue retention are low impact velocity and material properties such as high melting point. In general, the SEM-EDX observations of crater residues are consistent with the properties of chondritic meteorites and interplanetary dust particles collected in the stratosphere. Except for impacts by particles dominated by single minerals such as FeS and olivine, most of the residue compositions are in broad agreement with the major element compositions of chondrites. In most cases the residue is a thin liner on the crater floor and these craters are difficult to quantitatively analyze by EDX techniques because the electron beam excites both residue and underlying metal substrate. In favorable cases, the liner is thick and composed of vesicular glass with imbedded FeNi, sulfide and silicate grains. In the best cases of meteoroid preservation, the crater is lined with large numbers of unmelted mineral grains. The projectiles fragmented into micron sized pieces but the fragments survived without melting. In one case, the grains contain linear defects that appear to be solar flare tracks. Solar flare tracks are common properties of small interplanetary particles and their preservation during impact implies that the fragments were not heated above 600 C. We are investigating the meteoroid fragments in LDEF metal craters to determine the properties of interplanetary dust and to determine if there are meteoroid types that are overlooked or otherwise undetected in cosmic dust collections obtained from the stratosphere and polar ice.

Brownlee, D. E.↗

Production of Lunar Concrete Using Molten Sulfur

The United States has made a commitment to go back to the moon to stay in the early part of the next century. In order to achieve this objective it became evident to NASA that a Lunar Outpost will be needed to house scientists and astronauts who will be living on the moon for extended periods of time. A study has been undertaken by the authors and supported by NASA to study the feasibility of using lunar regolith with different binders such as molten sulfur, epoxy or hydraulic cement as a construction material for different lunar structures. The basic premise of this study is that it will be more logical and cost effective to manufacture lunar construction materials utilizing indigenous resources rather than transporting needed materials from earth. Lunar concrete (made from Hydraulic Cement and lunar soil) has been studied and suggested as the construction material of choice for some of the lunar projects. Unfortunately, its hydration requires water which is going to be a precious commodity on the moon. Therefore this study explores the feasibility of using binders other than hydraulic cement such as sulfur or epoxy with lunar regolith as a construction material. This report describes findings of this study which deals specifically with using molten sulfur as a binder for Lunar concrete. It describes laboratory experiments in which the sulfur to lunar soil simulant ratios by weight were varied to study the minimum amount of sulfur required to produce a particular strength. The compressive and tensile strengths of these mixes were evaluated. Metal and fiber glass fibers were added to some of the mixes to study their effects on the compressive and tensile strengths. This report also describes experiments where the sulfur is melted and mixed with the lunar regolith in a specially designed vacuum chamber. The properties of the produced concrete were compared to those of concrete produced under normal pressure.

Omar, Husam A.↗

Rare Earth Element Partition Coefficients from Enstatite/Melt Synthesis Experiments

Enstatite (En(80)Fs(19)Wo(01)) was synthesized from a hypersthene normative basaltic melt doped at the same time with La, Ce, Nd, Sm, Eu, Dy, Er, Yb and Lu. The rare earth element concentrations were measured in both the basaltic glass and the enstatite. Rare earth element concentrations in the glass were determined by electron microprobe analysis with uncertainties less than two percent relative. Rare earth element concentrations in enstatite were determined by secondary ion mass spectrometry with uncertainties less than five percent relative. The resulting rare earth element partition signature for enstatite is similar to previous calculated and composite low-Ca pigeonite signatures, but is better defined and differs in several details. The partition coefficients are consistent with crystal structural constraints.

Schwandt, Craig S.↗

A High Resolution Microprobe Study of EETA79001 Lithology C

Antarctic meteorite EETA79001 has received substantial attention for possibly containing a component of Martian soil in its impact glass (Lithology C) [1]. The composition of Martian soil can illuminate near-surface processes such as impact gardening [2] and hydrothermal and volcanic activity [3,4]. Impact melts in meteorites represent our most direct samples of Martian regolith. We present the initial findings from a high-resolution electron microprobe study of Lithology C from Martian meteorite EETA79001. As this study develops we aim to extract details of a potential soil composition and to examine Martian surface processes using elemental ratios and correlations.

Schrader, Christian M.↗

Endogenous Lunar Volatiles

The chapter will begin with an introduction that defines magmatic volatiles (e.g., H, F, Cl, S) versus geochemical volatiles (e.g., K, Rb, Zn). We will discuss our approach of understanding both types of volatiles in lunar samples and lay the ground work for how we will determine the overall volatile budget of the Moon. We will then discuss the importance of endogenous volatiles in shaping the "Newer Views of the Moon", specifically how endogenous volatiles feed forward into processes such as the origin of the Moon, magmatic differentiation, volcanism, and secondary processes during surface and crustal interactions. After the introduction, we will include a re-view/synthesis on the current state of 1) apatite compositions (volatile abundances and isotopic compositions); 2) nominally anhydrous mineral phases (moderately to highly volatile); 3) volatile (moderately to highly volatile) abundances in and isotopic compositions of lunar pyroclastic glass beads; 4) volatile (moderately to highly volatile) abundances in and isotopic compositions of lunar basalts; 5) volatile (moderately to highly volatile) abundances in and isotopic compositions of melt inclusions; and finally 6) experimental constraints on mineral-melt partitioning of moderately to highly volatile elements under lunar conditions. We anticipate that each section will summarize results since 2007 and focus on new results published since the 2015 Am Min review paper on lunar volatiles [9]. The next section will discuss how to use sample abundances of volatiles to understand the source region and potential caveats in estimating source abundances of volatiles. The following section will include our best estimates of volatile abundances and isotopic compositions (where permitted by available data) for each volatile element of interest in a number of important lunar reservoirs, including the crust, mantle, KREEP, and bulk Moon. The final section of the chapter will focus upon future work, outstanding questions, and any in-sights on the types of samples or experimental studies that will be needed to answer these questions.

McCubbin, F. M.↗

Pyrolysis Rate and Yield Strength Reduction in Carbon Fiber and Glass Fiber Composites under Reentry Heating Conditions

The behavior of composite materials, specifically carbon fiber-reinforced polymer (CFRP) and glass fiber-reinforced polymer (GFRP), under re-entry conditions poses a problem for orbital debris re-entry risk modeling. Since these materials pyrolyze rather than melt and their different components demise at different rates, modeling their destruction to determine ground impact risk is complex. Modern spacecraft are using these materials in ever-greater quantities owing to their superior strength-to -weight characteristics, and this has required that the orbital debris community improve its understanding of how these materials demise on re-entry.

Benton R Greene↗

Dissemination and fractionation of projectile materials in the impact melts from Wabar Crater, Saudi Arabia

Results are presented from the analyses of small ballistically dispersed melt samples (occurring in the form of aerodynamically shaped spheres, dumbbells, and teardrops) from the Wabar Crater (Saudi Arabia) and of melts from the Wabar and Nejed meteorites. On the basis of the data obtained and of models for crater forming processes it is concluded that the ballistically-dispersed glasses were formed from material at shallow levels in the target zone where temperatures were higher and where intimate physical contact with the disrupting impactor was achieved. Siderophile element fractionation was completed early, while the impactor was undergoing decompression and prior to mixing with the target glasses.

Mittlefehldt, David W.↗

Diamines Containing Pendent Phenylethynyl Groups

Controlled molecular weight imide oligomers and co-oligomers containing pendent phenylethynyl groups (PEPIs) and endcapped with nonreactive or phenylethynyl groups have been prepared by the cyclodehydration of the precursor amide acid oligomers or co-oligomers containing pendent phenylethynyl groups and endcapped with nonreactive or phenylethynyl groups. The amine terminated amide acid oligomers or co-oligomers are prepared from the reaction of dianhydride(s) with an excess of diamine(s) and diamine containing pendent phenylethynyl groups and subsequently endcapped with a phenylethynyl phthalic anhydride or monofunctional anhydride. The anhydride terminated amide acid oligomers and co-oligomers are prepared from the reaction of diamine(s) and diamine containing pendent phenylethynyl group(s) with an excess of dianhydride(s) and subsequently endcapped with a phenylethynyl amine or monofunctional amine. The polymerizations are carried out in polar aprotic solvents such as and N,N-dimethylacetamide under nitrogen at room temperature. The amide acid oligomers or co-oligomers are subsequently cyclodehydrated either thermally or chemically to the corresponding imide oligomers. The polymers and copolymers prepared from these materials exhibit a unique and unexpected combination of properties that includes higher glass transition temperatures after curing and higher retention of neat resin, adhesive and carbon fiber reinforced mechanical properties at temperatures up to 204 C under wet conditions without sacrificing melt flow behavior and processability as compared to similar materials. These materials are useful as adhesives, coatings, films, moldings, and composite matrices.

Connell, John W.↗

Insulation Material

Manufactured by Hitco Materials Division of Armco, Inc. a ceramic fiber insulation material known as Refrasil has been used extensively as a heat-absorbing ablative reinforcement for such space systems as rocket motor nozzles, combustion chambers, and re-entry shields. Refrasil fibers are highly porous and do not melt or vaporize until fibers exceed 3,100 degrees Fahrenheit. Due to these and other properties, Refrasil has found utility in a number of industrial high temperature applications where glass, asbestos and other materials fail. Hitco used this insulation to assist Richardson Co., Inc. in the manufacturing of hard rubber and plastic molded battery cases.

Source record↗

Experiments leading to the production of new glasses in space.

Report on an experimental program aimed at verifying proposed concepts of glassmaking in space from substances that to date have been observed only in a crystalline condition. A summary is presented on the results of experiments conducted by laser melting of ceramic rods of chosen composition and allowing the droplets ejected from the spinning rod to cool by free falling. This technique should permit an early evaluation of which compositions are most suitable for subsequent more expensive space experiments.

Happe, R. A.↗

Iron metal production in silicate melts through the direct reduction of Fe/II/ by Ti/III/, Cr/II/, and Eu/II/

The production of metallic iron in silicate melts by chemical reactions of Ti(3+), Cr(2+), and Eu(2+) with Fe(2+) is demonstrated under experimental conditions in a simplified basaltic liquid. These reactions form a basis for interpreting the role of isochemical valency exchange models in explanations for the reduced nature of lunar basalts. The redox couples are individually investigated in the silicate melt to ascertain reference redox ratios that are independent of mutual interactions. These studies also provide calibrations of spectral absorptions of the Fe(2+) and Ti(2+) species in these glasses. Subsequent spectrophotometric analyses of Fe(2+) and Ti(2+) in glasses doped with both iron and titanium and of Fe(2+) in glasses doped with either iron and chromium or iron and europium ascertain the degree of mutual interactions in these dual-doped glasses.

Schreiber, H. D.↗

Apollo 15 yellow-brown volcanic glass - Chemistry and petrogenetic relations to green volcanic glass and olivine-normative mare basalts

Electron microprobe and INAA were used to analyze forty spherules of Apollo 15 yellow-brown glass for major and trace elements. The glass is one of twenty-five high-Mg primary magmas emplaced on the lunar surface in pyroclastic eruptions. The abundances show that the magma was produced by partial melting of differentiated cumulates in the lunar mantle. Models to explain the possible source-regions of several Apollo 15 and Apollo 12 low-Ti mare magmas are presented.

Hughes, S. S.↗

Low Viscosity Imides Based on Asymmetric Oxydiphthalic Anhydride

A series of low-melt viscosity imide resins were prepared from asymmetric oxydiphthalic dianhydride (a-ODPA) and 4-phenylethynylphthalic anhydride as the endcap, along with 3,4' - oxydianiline (3,4' -ODA), 3,4' -methylenedianiline (3,4' -MDA), 3,3' -methylenedianiline (3,3' - MDA) and 3,3'-diaminobenzophenone (3,3'-DABP), using a solvent-free melt process. These imide oligomers displays low-melt viscosities (2-15 poise) at 260-280 C, which made them amenable to low-cost resin transfer molding (RTM) process. The a-ODPA based RTM resins exhibits glass transition temperatures (Tg's) in the range of 265-330 C after postcure at 343 C. The mechanical properties of these polyimide/carbon fiber composites fabricated by RTM will be discussed.

Chuang, Kathy C.↗

Castable Amorphous Metal Mirrors and Mirror Assemblies

A revolutionary way to produce a mirror and mirror assembly is to cast the entire part at once from a metal alloy that combines all of the desired features into the final part: optical smoothness, curvature, flexures, tabs, isogrids, low CTE, and toughness. In this work, it has been demonstrated that castable mirrors are possible using bulk metallic glasses (BMGs, also called amorphous metals) and BMG matrix composites (BMGMCs). These novel alloys have all of the desired mechanical and thermal properties to fabricate an entire mirror assembly without machining, bonding, brazing, welding, or epoxy. BMGs are multi-component metal alloys that have been cooled in such a manner as to avoid crystallization leading to an amorphous (non-crystalline) microstructure. This lack of crystal structure and the fact that these alloys are glasses, leads to a wide assortment of mechanical and thermal properties that are unlike those observed in crystalline metals. Among these are high yield strength, carbide-like hardness, low melting temperatures (making them castable like aluminum), a thermoplastic processing region (for improving smoothness), low stiffness, high strength-to-weight ratios, relatively low CTE, density similar to titanium alloys, high elasticity and ultra-smooth cast parts (as low as 0.2-nm surface roughness has been demonstrated in cast BMGs). BMGMCs are composite alloys that consist of a BMG matrix with crystalline dendrites embedded throughout. BMGMCs are used to overcome the typically brittle failure observed in monolithic BMGs by adding a soft phase that arrests the formation of cracks in the BMG matrix. In some cases, BMGMCs offer superior castability, toughness, and fatigue resistance, if not as good a surface finish as BMGs. This work has demonstrated that BMGs and BMGMCs can be cast into prototype mirrors and mirror assemblies without difficulty.

Hofmann, Douglas C.↗

Shock-induced melting in anorthositic rock 60015 and a fragment of anorthositic breccia from the 'picking pot' /70052/

Microscopic and chemical evidence are presented to support the contention that shock-generated incipient grain-boundary melting of plagioclase occurred in an anorthositic lunar rock and that shock-generated plagioclase liquid was present along grain boundaries during post-shock adiabatic expansion in a fragment of anorthositic breccia. The first contention is supported by microtextural relationships in the rock, the composition of its metal particles (most iron with some cobalt and less nickel), and glass inclusions with vapor bubbles. The second contention is supported by angular irregular voids in the fragment as well as the occurrence of oriented glass filaments in some of the voids. It is shown that shock-generation of 'cataclastic anorthosite' and high-temperature plagioclase liquids can explain the exceptionally young lead and argon ages of the anorthositic rock. The results of the breccia study indicate that shock lithification of plagioclase-rich particulate material from the highland regolith is due to grain-boundary melting of plagioclase.

Sclar, C. B.↗

Metamorphic effects in experimentally heated Krymka /L3/ chondrite

Experimental charges of the Krymka unequilibrated ordinary chondrite heated from 500-1000 C have been examined petrographically for evidence of metamorphism. Of the petrologic criteria commonly used to distinguish types 4-6 chondrites, only changes in opaque mineral compositions are observed. Chemical and textural observations indicate development of a fine-grained intergrowth of taenite + troilite beginning at 700 C due to melting within the metal-rich portion of the Fe-Ni-S system, and minor reduction of troilite to metal, possibly through sulfur loss at higher temperatures. Overall textural integration, glass devitrification, and significant Fe-enrichment of ferromagnesian minerals are not observed because the short duration of these experiments was not sufficient for the development of other changes normally attributed to metamorphism in ordinary chondritic meteorites.

Mcsween, H. Y., Jr.↗

Modelling of dispersal and deposition of impact glass spherules from the Cretaceous-Tertiary boundary deposit

The dispersal of glass spherules or tektites from a bolide impact with the Earth is modelled as ballistic trajectories in standard atmosphere. Ballistic dispersal of Cretaceous-Tertiary boundary impact glass spherules found in Haiti and Mimbral, Mexico requires a fireball radius in excess of 50 km but less than 100 km to account for the observed distribution. Glass spherules from 1 and up to 8 mm in diameter have been found at the KT boundary at Beloc in Haiti, at Mimbral, Mexico, and at DSDP Sites 536 and 540 in the Gulf of Mexico corresponding to paleodistances of 600 to 1000 km from the Chicxulub crater. In Haiti the basal and major glass-bearing unit at the KT boundary is attributed to fallout on basis of sedimentologic features. When compared with theoretical and observed dispersal of volcanic ejecta, the grain size versus distance relationship of the KT boundary tektite fallout is extreme, and rules out a volcanic fallout origin. At a comparable distance from source, the KT impact glass spherules are more than an order of mangitude coarser than ejecta of the largest known volcanic events. We model the dispersal of KT boundary impact glass spherules as ballistic ejecta from a fireball generated by the impact of a 10 km diameter bolide. Mass of ejecta in the fireball is taken as twice the bolide mass. Melt droplets are accelerated by gas flow in the fireball cloud, and leave the fireball on ballistic trajectories within the atmosphere, subject to drag, depending on angle of ejection and altitude. The model for ballistic dispersal is based on equations of motion, drag and ablation for silicate spheres in standard atmosphere.

Espindola, J. M.↗

Insights Into Reconstructing REE Compositions of Melt From Zircon-Melt Partition Coefficients Using Zircon-Hosted Melt Inclusions From the Yellowstone Volcanic Province

Establishing the major and trace element composition of the Earth’s melts (Hadean to recent) is essential for understanding crustal evolution. Due to its physical-chemical resilience, zircon spans the complete age spectra of Earth’s history, and thus provides the only physical record from the early Earth. However, the petrological context i.e., the melt from which zircon crystallised, is often lost, except for inclusions of melt preserved within zircon. Melt inclusions in zircon (MI) provide a valuable tool to constrain zircon-melt REE partition coefficients (D REE ), which are used with the zircon REE chemistry to reconstruct melt compositions. Such reconstruction requires accurate partition coefficients, which are particularly sensitive to temperature, but also to pressure and melt composition. We determined the major and trace element compositions of 60 co-existing zircon-MI pairs from two ~ 2 Ma age rhyolites (the caldera-forming Huckleberry Ridge Tuff; HRT-C and the post-caldera Blue Creek Flow; BC-1) of the Yellowstone Plateau volcanic field by EPMA and SIMS, and calculated a set of 60 zircon-MI partition coefficients. The MI from both units are glassy with average silica contents of 78.30 ± 0.74 and 77.19 ± 1.11 wt %, and Ti-in-zircon crystallisation temperatures are 839 ± 36 and 835 ± 35 oC. Measured D REE patterns for each population (n = 30) are tightly constrained and exhibit a smooth pattern spanning ~ six orders of magnitude from La to Lu, (with exceptions at Ce and Eu), and for the HRT exhibit greater curvature (i.e., flatter) between the MREE to HREE compared to the BC-1. D REE patterns for the HRT have small to moderate Ce anomalies (Ce/Ce* Di 50 ± 40), whereas those in the BC-1 are larger (98 ± 45), and both units exhibit negligible to positive Eu anomalies (Eu/Eu* Di 1.07 ± 0.89 and 1.80 ± 2.01, respectively). We compare the trace element compositions of the MI to bulk-glass compositions from Yellowstone to assess any differences, which are small, then compare the measured MI compositions to those reconstructed using published partition coefficients (natural, empirical and experimental). The choice of D REE for reconstruction of the melt REE pattern results in differing petrogenetic interpretations.

Laura J. Crisp↗