SEARCH · Engineering Papers

Results for “frequency response control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 613 records · Page 34

All sources NASA NTRS DOE OSTI

NASA NTRS1976

A source array for generating higher order acoustic modes in circular ducts

A unique source array has been developed for the generation of both spinning and non-spinning higher order modes in a circular duct. The array consists of two concentric rings of sources. Through individual control of the response of each element, the array provided phase and amplitude control in the radial as well as circumferential directions. Radial modes shapes were measured in a 12-inch diameter anechoically-terminated hollow duct. These modes could be generated at their cut-off frequency and throughout a frequency range extending to the cut-off frequency for the next higher order radial mode. Comparisons are given between theory and experiment for the generation of specific modes. The radial dependence of the measured mode shapes was enhanced considerably by the design of this array. The results indicate a significant improvement over previous mode generation mechanisms. The contamination of the generated mode by additional spurious modes is also considered for variations between individual elements within the source array.

Wyerman, B. R.↗

NASA NTRS1978

Optimal regulator or conventional? Setup techniques for a model following simulator control system

Optimal regulator technique was compared for determining simulator control system gains with the conventional servo analysis approach. Practical considerations, associated with airborne motion simulation using a model-following system, provided the basis for comparison. The simulation fidelity specifications selected were important in evaluating the relative advantages of the two methods. Frequency responses for a JetStar aircraft following a roll mode model were calculated digitally to illustrate the various cases. A technique for generating forward loop lead in the optimal regulator model-following problem was developed which increases the flexibility of that approach. It appeared to be the only way in which the optimal regulator method could meet the fidelity specifications.

Deets, D. A.↗

NASA NTRS1986

Effect of water immersion on cardiopulmonary physiology at high gravity (+Gz)

The cardiopulmonary responses of eight male subject between 21-31 years exposed to 1, 2, and 3 Gz during immersion at 35 + or - 0.5 C to heart level and during control dry rides are studied. Ventilation, O2 consumption, the end-tidal pressure of CO2, heart frequency, cardiac output, functional residual capacity, and the arterial pressure of CO2 were measured. It is observed that as Gz increases ventilation, heart frequency, and O2 consumption increase, and the end-tidal and arterial pressures of CO2 decrease during dry rides, but are not altered during immersion. It is detected that the functional residual capacity is lower during immersion and decreases in both the dry and immersed state as Gz increases, and cardiac output decreases as Gz increases in dry rides. It is noted that changes produced by acceleration in a Gz direction are due to the effect on the systemic circulation rather than to the effect on the lungs.

Arieli, R.↗

NASA NTRS1988

Effects of nonlinear damping in flexible space structures

The classical Krylov-Bogoliubov "averaging" technique is used to study a class of nonlinear damping models, for which the damping force is proportional to the product of positive integer or fractional power of absolute values of displacement and that of velocity. The results are compared with linear viscous damping models. The amplitude decrement of free vibration for a single mode system with nonlinear models depends not only on damping ratio, but also on the initial amplitude, the time to measure the response, frequency of the system, and the powers of displacement and velocity. For the distributed system, the action of nonlinear damping is found to reduce energy of the system as well as to pass energy to higher modes. Experimental evidence such as in Spacecraft Control Laboratory Experiment seems to support the need for nonlinear models.

Hu, Anren↗

NASA NTRS1990

Payload vibration isolation in a microgravity environment

Many in-space research experiments require the microgravity environment attainable near the center of mass of the Space Station. Disturbances to the structure surrounding an experiment may lead to vibration levels that will degrade the microgravity environment and undermine the experiment's validity. In-flight disturbances will include vibration transmission from nearby equipment and excitation from crew activity. Isolation of these vibration-sensitive experiments is required. Analytical and experimental work accomplished to develop a payload (experiment) isolation system for use in space is described. The isolation scheme allows the payload to float freely within a prescribed boundary while being kept centered with forces generated by small jets of air. The vibration criterion was a maximum payload acceleration of 10 micro-g's (9.81x10(exp -5)m/s(exp 2), independent of frequency. An experimental setup, composed of a cart supported by air bearings on a flat granite slab, was designed and constructed to simulate the microgravity environment in the horizontal plane. Experimental results demonstrate that the air jet control system can effectively manage payload oscillatory response. An analytical model was developed and verified by comparing predicted and measured payload response. The mathematical model, which includes payload dynamics, control logic, and air jet forces, is used to investigate payload response to disturbances likely to be present in the Space Station.

Alexander, Richard M.↗

NASA NTRS1990

Robust time-domain identification of mass stiffness, and damping matrices

Accurate estimates of the mass, stiffness, and damping characteristics of a structure is necessary for determining the control laws best suited for active control methodologies. There are several modal identification techniques available for determining the frequencies, damping ratios, and mode shapes of a structure. However, modal identification methods in both the frequency and time domains have difficulties for certain circumstances. Frequency domain techniques which utilize the steady-state response from various harmonic inputs often encounter difficulties when the frequencies are closely distributed, the structure exhibits a high degree of damping, or the steady-state condition is hard to establish. Time domain techniques have produced successful results, but lack robustness with respect to measurement noise. In this paper, two identification techniques and an estimation method are combined to form a time-domain technique to accurately identify the mass, stiffness, and damping matrices from noisy measurements.

Roemer, Michael J.↗

NASA NTRS1991

Flying quality analysis and flight evaluation of a highly augmented combat rotorcraft

This paper discusses implications of digital flight control system design for rotorcraft and illustrates the analysis of the resulting handling qualities obtained with the Advanced Digital Optical Control System demonstrator in the context of the proposed new handling-qualities specification for rotorcraft. Topics covered are digital flight control design and analysis methods, flight testing techniques, handling-qualities evaluation results, and correlation of flight test results with analytical models and the proposed handling-qualities specification. The evaluation of the demonstrator system indicates desirable response characteristics based on equivalent damping and frequency, but undersirably large effective time delays (exceeding 240 ms in all axes). Piloted handling qualities are found to be desirable or adequate for all low, medium, and high pilot gain tasks, but handling qualities are inadequate for ultrahigh gain tasks such as slope and running landings. Correlation of these results with the proposed handling-qualities specification indicates good agreement for the bandwidth boundaries, but suggests the need for more stringent limits on allowable phase delay. Analytical models based on emulation (s-plane) techniques compare favorably with flight-extracted frequency-domain characteristics of the overall (end-to-end) system responses.

Tischler, Mark B.↗

NASA NTRSDate not supplied

Sliding Mode Transient Scaling Controller for Gas Turbine Engine Emulation on an Electric Machine

The testing of hybrid-electric aircraft propulsion system components and control strategies has dictated the need for a low-cost gas turbine engine (GTE) emulation testbed. Within that testbed, electric machines (EMs) are used to emulate the dynamics of a GTE. GTE mathematical models are used to provide control torque commands to EMs. Most GTEs operate at much higher power levels than commercially available EMs. Therefore, the transient shaft dynamics of the GTE must be scaled appropriately. The sliding mode controller being presented here aims to deliver a control torque to an electric machine with a fixed inertia that will allow it to mimic the response of a GTE with a different inertia. This solution provides an easily scalable and tunable transient emulation method without having to scale the GTE mathematical model and/or add inertia to the physical EM shaft. This controller has been proven in simulation to produce nearly identical transient rotational speed response to a reference GTE shaft model which has a large difference in rotational inertia compared to the motor. Also, the inherent robustness of the sliding mode control scheme results in negligible changes in performance for large amounts of parameter uncertainty while minimizing high frequency fluctuations in the control signal.

sliding mode↗

NASA NTRS1974

Tradeoffs in manipulator structure and control. Part 4: Flexible manipulator analysis program

The Flexible Manipulator Analysis Program (FMAP) is a collection of FORTRAN coding to allow easy analysis of the flexible dynamics of mechanical arms. The user specifies the arm configuration and parameters and any or all of several frequency domain analyses to be performed, while the time domain impulse response is obtained by inverse Fourier transformation of the frequency response. A detailed explanation of how to use FMAP is provided.

Book, W. J.↗

NASA NTRS1971

Substructuring techniques

The substructure function generator program is discussed. Input to this program consists of a definition of a finite element model of a substructure, and specification of the type and number of displacement functions to be generated. Primary output is a substructure data file containing the substructure mass and stiffness matrices expressing kinetic and potential energies as quadratic forms in coefficients of the displacement functions, etc. The substructure synthesis program forms complete system mass, stiffness, and damping matrices, computes system modes and frequencies, and executes transient response calculations. Input to this program consists of the array of substructure data files generated by the function generator program for individual substructures, and data cards defining the position and interconnection of the substructures, damping data, forcing function details, and function control parameters.

Whetstone, W. D.↗

NASA NTRS1989

Applications of flight control system methods to an advanced combat rotorcraft

Advanced flight control system design, analysis, and testing methodologies developed at the Ames Research Center are applied in an analytical and flight test evaluation of the Advanced Digital Optical Control System (ADOCS) demonstrator. The primary objectives are to describe the knowledge gained about the implications of digital flight control system design for rotorcraft, and to illustrate the analysis of the resulting handling-qualities in the context of the proposed new handling-qualities specification for rotorcraft. Topics covered in-depth are digital flight control design and analysis methods, flight testing techniques, ADOCS handling-qualities evaluation results, and correlation of flight test results with analytical models and the proposed handling-qualities specification. The evaluation of the ADOCS demonstrator indicates desirable response characteristics based on equivalent damping and frequency, but undersirably large effective time-delays (exceeding 240 m sec in all axes). Piloted handling-qualities are found to be desirable or adequate for all low, medium, and high pilot gain tasks; but handling-qualities are inadequate for ultra-high gain tasks such as slope and running landings.

Tischler, Mark B.↗

NASA NTRS1990

Active control of the forced response of a finite beam

The theoretical limit on reducing transverse vibrations in a simply-supported finite beam is investigated. The beam is assumed to be harmonically excited to a steady-state condition and controlled by single point sources. Results demonstrate the maximum possible attenuation of the beam vibrations as a function of excitation frequency, controller location, and spatial area of control.

Post, John T.↗

NASA NTRS1997

PLATSIM: A Simulation and Analysis Package for Large-Order Flexible Systems

The software package PLATSIM provides efficient time and frequency domain analysis of large-order generic space platforms. PLATSIM can perform open-loop analysis or closed-loop analysis with linear or nonlinear control system models. PLATSIM exploits the particular form of sparsity of the plant matrices for very efficient linear and nonlinear time domain analysis, as well as frequency domain analysis. A new, original algorithm for the efficient computation of open-loop and closed-loop frequency response functions for large-order systems has been developed and is implemented within the package. Furthermore, a novel and efficient jitter analysis routine which determines jitter and stability values from time simulations in a very efficient manner has been developed and is incorporated in the PLATSIM package. In the time domain analysis, PLATSIM simulates the response of the space platform to disturbances and calculates the jitter and stability values from the response time histories. In the frequency domain analysis, PLATSIM calculates frequency response function matrices and provides the corresponding Bode plots. The PLATSIM software package is written in MATLAB script language. A graphical user interface is developed in the package to provide convenient access to its various features.

Maghami, Peiman G.↗

NASA NTRS2006

High-Performance Scanning Acousto-Ultrasonic System

A high-performance scanning acousto-ultrasonic system, now undergoing development, is designed to afford enhanced capabilities for imaging microstructural features, including flaws, inside plate specimens of materials. The system is expected to be especially helpful in analyzing defects that contribute to failures in polymer- and ceramic-matrix composite materials, which are difficult to characterize by conventional scanning ultrasonic techniques and other conventional nondestructive testing techniques. Selected aspects of the acousto-ultrasonic method have been described in several NASA Tech Briefs articles in recent years. Summarizing briefly: The acousto-ultrasonic method involves the use of an apparatus like the one depicted in the figure (or an apparatus of similar functionality). Pulses are excited at one location on a surface of a plate specimen by use of a broadband transmitting ultrasonic transducer. The stress waves associated with these pulses propagate along the specimen to a receiving transducer at a different location on the same surface. Along the way, the stress waves interact with the microstructure and flaws present between the transducers. The received signal is analyzed to evaluate the microstructure and flaws. The specific variant of the acousto-ultrasonic method implemented in the present developmental system goes beyond the basic principle described above to include the following major additional features: Computer-controlled motorized translation stages are used to automatically position the transducers at specified locations. Scanning is performed in the sense that the measurement, data-acquisition, and data-analysis processes are repeated at different specified transducer locations in an array that spans the specimen surface (or a specified portion of the surface). A pneumatic actuator with a load cell is used to apply a controlled contact force. In analyzing the measurement data for each pair of transducer locations in the scan, the total (multimode) acousto-ultrasonic response of the specimen is utilized. The analysis is performed by custom software that extracts parameters of signals in the time and frequency domains. The computer hardware and software provide both real-time and postscan processing and display options. For example, oscilloscope displays of waveforms and power spectral densities are available in real time. Images can be computed while scanning continues. Signals can be digitally preprocessed and/or post-processed by filtering, windowing, time-segmenting, and running-waveform-averaging algorithms. In addition, the software affords options for off-line simulation of the waveform-data-acquisition and scanning processes. In tests, the system has been shown to be capable of characterizing microstructural changes and defects in SiC/SiC and C/SiC ceramic-matrix composites. Delaminations, variations in density, microstructural changes attributable to infiltration by silicon, and crack-space indications (defined in the next sentence) have been revealed in images formed from several time- and frequency-domain parameters of scanning acousto-ultrasonic signals. The crack-space indications were image features that were not revealed by other nondestructive testing methods and are so named because they turned out to mark locations where cracking eventually occurred.

Roth, Don↗

NASA NTRS1985

Application of frequency domain handling qualities criteria to the longitudinal landing task

Under NASA sponsorship, an in-flight simulation of the longitudinal handling qualities of several configurations for the approach and landing tasks was performed on the USAF/AFWAL Total In-Flight Simulator by the Calspan Corporation. The basic configuration was a generic transport airplane with static instability. The control laws included proportional plus integral gain loops to produce pitch-rate and angle-of-attack feedback loops. The evaluation task was a conventional visual approach to a flared touchdown at a designated spot on the runway with a lateral offset. The general conclusions were that the existing criteria are based on pitch-attitude response and that these characteristics do not adequately discriminate between the good and bad configurations of this study. This paper describes the work that has been done to further develop frequency-based criteria in an effort to provide better correlation with the observed data.

Sarrafian, S. K.↗

NASA NTRS1991

The zeroes of controlled structures - Sensor/actuator attributes and structural modelling

The effects of sensor/actuator design and modeling decisions on the zero frequencies of single input single output structural systems are explored. A zero definition based on the high gain closed loop character of the poles of a system is used to study parametrically zeroes as a function of sensor and actuator location. An infinite order model is adopted so that the effects of finite order modeling are removed. Examples focus on point or localized actuators and sensors and simple uniform structures. The sensitivity of the zero frequencies to changes in the sensor and actuator location for both collocated and non-collocated cases are presented. Non-minimum phase behavior is visible in only certain non-collocated situations. In addition to the sensor/actuator attributes, the zeroes are shown to be a function of the truncation and discretization used to model the structural response for collocated and dual systems. Methods for improving the zero predictions in the control bandwidth are suggested.

Fleming, Farla M.↗

NASA NTRS1977

Study of synthesis techniques for insensitive aircraft control systems

Insensitive flight control system design criteria was defined in terms of maximizing performance (handling qualities, RMS gust response, transient response, stability margins) over a defined parameter range. Wing load alleviation for the C-5A was chosen as a design problem. The C-5A model was a 79-state, two-control structure with uncertainties assumed to exist in dynamic pressure, structural damping and frequency, and the stability derivative, M sub w. Five new techniques (mismatch estimation, uncertainty weighting, finite dimensional inverse, maximum difficulty, dual Lyapunov) were developed. Six existing techniques (additive noise, minimax, multiplant, sensitivity vector augmentation, state dependent noise, residualization) and the mismatch estimation and uncertainty weighting techniques were synthesized and evaluated on the design example. Evaluation and comparison of these six techniques indicated that the minimax and the uncertainty weighting techniques were superior to the other six, and of these two, uncertainty weighting has lower computational requirements. Techniques based on the three remaining new concepts appear promising and are recommended for further research.

Harvey, C. A.↗

NASA NTRS1982

Generation of desired signals from acoustic drivers

A procedure to control transient signal generation is developed for the study of internal noise propagation from aircraft engines. A simple algorithm incorporating transform techniques is used to produce signals of any desired waveform from acoustic drivers. The accurate driver response is then calculated, and from this the limiting frequency characteristics are determined and the undesirable frequencies where the driver response is poor are eliminated from the analysis. A synthesized signal is then produced by convolving the inverse of the response function with the desired signal. Although the shape of the synthesized signal is in general quite awkward, the driver generates the desired signal when the distorted signal is fed into the driver. The results of operating the driver in two environments, in a free field and in a duct, are presented in order to show the impedance matching effect of the driver. In addition, results using a high frequency cut-off value as a parameter is presented in order to demonstrate the extent of the applicability of the synthesis procedure. It is concluded that the desired signals can be generated through the signal synthesis procedure.

Ramakrishnan, R.↗